فتوکپی رنگی,فتوکپی رنگی کونیکا,فتوکپی رنگی کونیکامینولتا,فتوکپی رنگی کونیکا مینولتا,فتوکپی رنگی کونیکامینولتا552,فتوکپی رنگی,کونیکا مینولتا 552, کونیکا مینولتا ,552 کونیکا مینولتا ,552 کونیکامینولتا ,552 کونیکامینولتا ,552فتوکپی رنگی کونیکامینولتابیزهاب55
(0) محصول

کونیکا مینولتا 350

5410 |
بازدید
قیمت: 0 ریال
موجودی انبار: نا محدود

توضیحات مختصر

لازم به توضیح است که با حذف ویا انتخاب هریک از فیلدهای اختیاری اعم از آپشن دستگاه ویا کارکرد آن قیمت تغیر خواهد کرد . پس قبل از خرید به با دقت مطالعه فرمایید. دستگاهي رنگي که با قابليتهاي ممتاز و منحصر بفرد خود از قبيل کپي برداري، پرينت و اسکن اسناد حجيم، با وضوحيتي بي نظير، موجب صرفه جوئي فوق العاده در زمان و هزينه هاي دفتر کار شما مي گردد. فتوکپی رنگی کونیکا مینولتا c450 از محسنات این سری فتوکپی رنگی بصرفه بودن و ارزان بودن مواد مصرفی و بورس بودن قطعات و خدمات فنی است. از لحاظ زمان ساخت جزو دستگاهای قدیمی محسوب میشه زیرا عمر مفید دستگاه رنگی سه سال می باشد به علت نوسانات قیمت ارز لطفا برای استعلام قیمت با شماره تلفنها ی زیر تماس حاصل فرمایید 04137222043-04137252392-04137254200-04137253033-04136586892-04137253034-09120370093-09148659399
سازنده: Konica Minolta

تعداد: 

 آرشیو فیلم های آموزشی

توضیح مختصری در موردکیفیت وآپشن های دستگاه رنگی کونیکامینولتا350

توضیح مختصری در مورد دستگاه رنگی کونیکامینولتا350

نحوه کپی کردن از حافظه دستگاه کونیکامینولتا 350

پیرنت روی پاکت در دستگاه رنگی کونیکامینولتا350

چاپ بنر در دستگاه کونیکا مینولتا 350

نحوه عوض کردن تونرکونیکا مینولتا ۳۵۰

راه اندازی اکسن در دستگاه کونیکا مینولتا 350

سرویس امیج کونیکا مینولتا350

 فرستادن فاکس با دستگاه کونیکامینولتا350

پشت رو زدن با دستگاه کونیکا مینولتا 450 (نحوه کاربادوبلکس

                                               رفع ایرادات کونیکا 350به صورت فیلمهای آموزشی برای مشتریانی که شماره اشتراک دارند

 

 

 

Code

Description

Remedy

C0000

Main Motor's failure to turn
• The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning.

1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the PWB-MC connector for proper connection and correct as necessary. PWB-MC PJ6MC-1 (DC24 Vcopyir.com 15-R 4 M1 operation check PWB-MC PJ11MC-6A (LOCKcopyir.com PWB-MC PJ11MC-3A (REMcopyir.com 6-Q. 5 Change PWB-MC. 6 Change PU1.

C0001

Main Motor turning at abnormal timing
• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

1 M1 operation check PWB-MC PJ11MC-6A (LOCKcopyir.com PWB-MC PJ11MC-3A (REMcopyir.com 6-Q. 2 Change PWB-MC. 3 Change PU1.

C0016

Bk PC Motor's failure to turn
• The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning.

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the connector of motor for proper drive coupling and correct as necessary. 3 Check the PWB-MC connector for proper connection and correct as necessary. PWB-MC PJ6MC-3 (DC24 Vcopyir.com 15-R. 4 M7 operation check PWB-MC PJ11MC-6B (LOCKcopyir.com PWB-MC PJ11MC-3B (REMcopyir.com 13-A. 5 Change PWB-MC.

C0017

Bk PC Motor's turning at abnormal timing
• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

1 M7 operation check PWB-MC PJ11MC-6B (LOCKcopyir.com PWB-MC PJ11MC-3B (REMcopyir.com 13-A. 2 Change PWB-MC.

C0018

Color PC Drum Motor's failure to turn
• The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning.

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the connector of motor for proper drive coupling and correct as necessary. 3 Check the PWB-MC connector for proper connection and correct as necessary. PWB-MC PJ6MC-5 (DC24 Vcopyir.com 15-R 4 M5 operation check (C0018copyir.com PWB-MC PJ11MC-13B (LOCKcopyir.com PWB-MC PJ11MC-10B (REMcopyir.com 13-B. 5 Change PWB-MC.

C0019

Color PC Drum Motor's turning at abnormal timing
• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

1 M5 operation check (C0019copyir.com PWB-MC PJ11MC-13B (LOCKcopyir.com PWB-MC PJ11MC-10B (REMcopyir.com 13-B. 2 Change PWB-MC.

C001A

Color Developing Motor's failure to turn
• The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning.

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the connector of motor for proper drive coupling and correct as necessary. 3 Check the PU-1 connector for proper connection and correct as necessary. PU1 PJ5PU1-13 (DC24 Vcopyir.com 22-E. 4 M6 operation check (C001Acopyir.com PWB-MC PJ2MC-6 (LOCKcopyir.com PWB-MC PJ2MC-3 (REMcopyir.com 13-D. 5 Change PU-1MC.

C001B

Color Developing Motor's turning at abnormal timing
• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

1 M6 operation check (C001Bcopyir.com PWB-MC PJ2MC-6 (LOCKcopyir.com PWB-MC PJ2MC-3 (REMcopyir.com 13-D. 2 Change PWB-MC.

C0040

Suction Fan Motor's failure to turn
• The Fan Lock signal remains HIGH for a predetermined continuous period of time while the Motor remains stationary.

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M12 operation check PWB-MC PJ18MC-9 (LOCKcopyir.com PWB-MC PJ18MC-7 (REMcopyir.com 6-P. 4 Change PWB-MC.

C0046

Fusing Cooling Fan Motor/1 failure to turn

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M9 operation check PU1 PJ17PU1-5 (LOCKcopyir.com 2-K 4 Change PU-1.

C0048

Fusing Cooling Fan Motor/1 or Fusing Cooling Fan Motor/2 failure to turn

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M15, M16 operation check M15: PWB-MC PJ3MC-6A (LOCKcopyir.com PWB-MC PJ3MC-4A (REMcopyir.com M16: PWB-MC PJ3MC-9A (LOCKcopyir.com PWB-MC PJ3MC-7A (REMcopyir.com 2-I (M15copyir.com 2-J (M16copyir.com. 4 Change PWB-MCWB-MC.

C004C

Ozone Ventilation Fan Motor's failure to turn

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M18 operation check PWB-MC PJ5MC-13 (LOCKcopyir.com PWB-MC PJ5MC-11 (REMcopyir.com 26-V. 4 Change PWB-MC.

C004D

Toner Suction Fan Motor's failure to turn

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M20 operation check PWB-MC PJ3MC-3A (LOCKcopyir.com PWB-MC PJ3MC-1A (REMcopyir.com 26-V. 4 Change PWB-MC.

C004E

Power Supply Cooling Fan Motor's failure to turn

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M21 operation check PU1 PJ12PU1-3 (LOCKcopyir.com 22-G 4 Change PU-1.

C004F

Cooling Fan Motor 2’s failure to turn

1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M10 operation check PWB-MC PJ5MC-7 (LOCKcopyir.com PWB-MC PJ5MC-6 (REMcopyir.com

C0060

Fusing Drive Motor’s failure to turn

1 Check the M2 connector for proper connection and correct as necessary. 2 Check the Fusing Unit drive for possible overload and correct as necessary. 3 Check the PWB-MC connector for proper connection and correct as necessary. PWB-MC PJ6MC-7 (DC24 Vcopyir.com 15-R. 4 M2 operation check PWB-MC PJ11MC-13A (LOCKcopyir.com PWB-MC PJ11MC-10A (REMcopyir.com 2-N. 5 Change PWB-MCB.

C0061

Fusing Drive Motor turning at abnormal timing
• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

1 M2 operation check PWB-MC PJ11MC-13A (LOCKcopyir.com PWB-MC PJ11MC-10A (REMcopyir.com 2-N. 2 Change PWB-MC.

C0094

2nd Image Transfer Roller pressure/retraction failure
• The 2nd Image Transfer Pressure Position Sensor is not activated (retracted positioncopyir.com within 2 sec. after the 2nd Image Transfer Pressure/Retraction Motor has started turning during a sequence of the 2nd Image Transfer Roller's retracting motion. • The 2nd Image Transfer Pressure Position Sensor is not deactivated (pressed positioncopyir.com within 2 sec. after the 2nd Image Transfer Pressure/Retraction Motor has started turning during a sequence of the 2nd Image Transfer Roller's pressing motion.

1 Check the M13 connector for proper connection and correct as necessary. 2 PC29 I/O check PWB-MC PJ12MC-9A (ONcopyir.com 6-B. 3 M13 operation check PWB-MC PJ18MC-1 (REMcopyir.com 6-A. 4 Change PWB-MC.

C0096

Image Transfer Belt pressure/ retraction failure
• The 1st Image Transfer Retraction Position Sensor is not activated (retracted positioncopyir.com within 5 sec. after the 1st Image Transfer Pressure/Retraction Motor has started turning during a sequence of the Transfer Belt's retracting motion. • The 1st Image Transfer Retraction Position Sensor is not deactivated (pressed positioncopyir.com within 1 sec. after the 1st Image Transfer Pressure/Retraction Motor has started turning during a sequence of the Transfer Belt's pressing motion.

1 Check the M11 connector for proper connection and correct as necessary. 2 PC12 I/O check PWB-MC PJ3MC-6B (ONcopyir.com 6-B. 3 M11 operation check PWB-MC PJ5MC-1~4 (Pulse Outputcopyir.com 6-C. 4 Change PWB-MC.

C0098

Fusing Pressure Roller pressure/ retraction failure
• No change is observed in the encoder sensor pulse even after the lapse of 0.5 sec. after the Fusing Pressure/Retraction Motor has started turning for a sequence of the Fusing Pressure Roller’s retracting motion. • No change is observed in the encoder sensor pulse even after the lapse of 0.5 sec. after the Fusing Pressure/Retraction Motor has started turning for a sequence of the Fusing Pressure Roller’s pressing motion. • The Fusing Pressure Position Sensor is not activated (pressed positioncopyir.com even when 30 encoder sensor pulses are counted after the Fusing Pressure/Retraction Motor has started turning for a sequence of the Fusing Pressure Roller’s pressing motion.

1 Check the M9 connector for proper connection and correct as necessary. 2 PC33 I/O check PWB-MC PJ7MC-12A (ONcopyir.com 2-M. 3 PC34 operation check PWB-MC PJ16MC-3A (Pulse Outputcopyir.com 16-P. 4 M19 operation check PWB-MC PJ19MC-5B,6B (Pulse Outputcopyir.com 2-J. 5 Change Fusing Unit. 6 Change PWB-MC.

C0200

Cyan PC Drum Charge Corona malfunction
• An output is automatically produced from the PC Drum Charge Corona of each color when the malfunction resetting procedure is performed after C0208 (PC Drum Charge Corona malfunctioncopyir.com has been detected. The SCD signal is detected for a continuous 0.5-sec. period at this time.

1 Check the Imaging Unit contact and correct or clean as necessary. 2 Check the HV1 contact and correct or clean as necessary. 3 Change Imaging Unit. 4 Change HV1. 5 Change PWB-MC.

C0202

Magenta PC Drum Charge Corona malfunction

1 Check the Imaging Unit contact and correct or clean as necessary. 2 Check the HV1 contact and correct or clean as necessary. 3 Change Imaging Unit. 4 Change HV1. 5 Change PWB-MC.

C0204

Yellow PC Drum Charge Corona malfunction

1 Check the Imaging Unit contact and correct or clean as necessary. 2 Check the HV1 contact and correct or clean as necessary. 3 Change Imaging Unit. 4 Change HV1. 5 Change PWB-MC.

C0206

Black PC Drum Charge Corona malfunction

1 Check the Imaging Unit contact and correct or clean as necessary. 2 Check the HV1 contact and correct or clean as necessary. 3 Change Imaging Unit. 4 Change HV1. 5 Change PWB-MC.

C0208

PC Drum Charge Corona malfunction
• The SCD signal is detected for a continuous 0.5-sec. period while the PC Drum Charge Corona is being energized.

1 Check the Imaging Unit contact and correct or clean as necessary. 2 Check the HV1 contact and correct or clean as necessary. 3 Change Imaging Unit. 4 Change HV1. 5 Change PWB-MC.

C0400

Exposure Lamp’s failure to turn ON
• The output from the CCD Sensor is a predetermined value or less during CCD Sensor gain adjustment.

1 Check the flat cable for proper connection and correct or change as necessary. 2 Change Scanner Assy. 3 Change PWB-C.

C0410

Exposure Lamp turning ON at abnormal timing
• The average output value of the CCD Sensor with the Scanner at its standby position is a predetermined value or more at the end of a scan job.

1 Check the flat cable for proper connection and correct or change as necessary. 2 Change Scanner Assy. 3 Change PWB-C.

C0500

Heating Roller warm-up failure
• The temperature of the Heating Roller does not reach 100 °C within 50 sec. after the Heating Roller Heater Lamp has been turned ON. • The temperature of the Heating Roller does not reach 100 °C and that of the Fusing Pressure Roller does not reach 195 °C within 200 sec. after the Heating Roller Heater Lamp has been turned ON. • The voltage of the Heating Roller Thermistor does not increase by five steps within 20 sec. after the Heating Roller Heater Lamp has been turned ON. • No zero cross signal is detected even with the lapse of 1 sec. or more after the Heating Roller Heater Lamp has been turned ON.

1 Check the Fusing Unit for correct installation (whether it is secured in positioncopyir.com. 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1.

C0501

Fusing Pressure Roller warm-up failure
• The voltage of the Fusing Pressure Roller Thermistor does not increase by five steps within 20 sec. after the predrive of the Fusing Roller has been started during a warm-up cycle.

1 Check the Fusing Unit for correct installation (whether it is secured in positioncopyir.com. 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1.

C0510

Heating Roller abnormally low temperature
• No zero cross signal is detected even with the lapse of 1 sec. or more during a standby state, print cycle, or Power Save. • A temperature of 120 °C or less of the Heating Roller is detected for 1 sec. or more during a standby state. • A temperature of 120 °C or less of the Heating Roller is detected for 1 sec. or more during a print cycle. • A temperature of 70 °C or less of the Heating Roller is detected for 1 sec. or more during Power Save.

1 Check the Fusing Unit for correct installation (whether it is secured in positioncopyir.com. 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1.

   
         

 

 

Brand:

 
 
 
 

 

 

  Download service manual PDF.

Model:

 

 

   

Free Parts Catalog on line.

 

Konica-Minolta bizhub C350 Trouble Error Codes List page 3 (from 8copyir.com

 

 

 

 

 

Code:

 

 

 

Code

Description

Remedy

C0511

Fusing Pressure Roller abnormally low temperature
• . A temperature of 80 °C or less of the Fusing Pressure Roller is detected for 1 sec. or more during a standby state. • A temperature of 80 °C or less of the Fusing Pressure Roller is detected for 1 sec. or more during a print cycle. • A temperature of 80 °C or less of the Fusing Pressure Roller is detected for 1 sec. or more during Power Save.

1 Check the Fusing Unit for correct installation (whether it is secured in positioncopyir.com. 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1.

C0520

Heating Roller abnormally high temperature
• A temperature of 225 °C or more of the Heating Roller is detected for 1 sec. or more.

1 Check the Fusing Unit for correct installation (whether it is secured in positioncopyir.com. 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1.

C0521

Fusing Pressure Roller abnormally high temperature
• A temperature of 190 °C or more of the Fusing Pressure Roller is detected for 1 sec. or more before the start of the heater temperature control. • A temperature of 215 °C or more of the Fusing Pressure Roller is detected for 1 sec. or more after the start of the heater temperature control.

1 Check the Fusing Unit for correct installation (whether it is secured in positioncopyir.com. 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1.

C0650

Scanner Home Sensor malfunction
• The Scanner Home Sensor is unable to detect the Scanner located at its home position. • The Scanner Home Sensor is unable to detect a Scanner even when the Scanner Motor has been driven to move the Scanner over the maximum traveling distance. • The Scanner Home Sensor detects the Scanner when the Scanner has moved 5 mm from the position, at which it blocks the Scanner Home Sensor.

1 Correct or change the Scanner drive (cable, pulley, gear, beltcopyir.com if it is faulty. 2 Correct the Scanner Motor set screw if loose. 3 Adjust “Top Image” and “FD-Mag”. 4 Check the PC201, M201, PWB-IC and PWB-C connector for proper connection and correct as necessary. 5 PC201 I/O check PWB-C PJ11C-8 (ONcopyir.com 21-Z 6 M201 operation check PWB-IC PJ3IC-3 (LOCKcopyir.com PWB-IC PJ3IC-1 (REMcopyir.com 25-Z. 7 Change PWB-IC. 8 Change PWB-C.

C0660

Scanner overrun failure
• The Scanner Home Sensor detects the Scanner at its home position during a period of time that begins with the time when a prescan command and a scan preparation command are executed and ends when a home return command is executed.

1 Correct or change the Scanner drive (cable, pulley, gear, beltcopyir.com if it is faulty. 2 Correct the Scanner Motor set screw if loose. 3 Adjust “Top Image” and “FD-Mag”. 4 Check the PC201, M201, PWB-IC and PWB-C connector for proper connection and correct as necessary. 5 PC201 I/O check PWB-C PJ11C-8 (ONcopyir.com 21-Z 6 M201 operation check PWB-IC PJ3IC-3 (LOCKcopyir.com PWB-IC PJ3IC-1 (REMcopyir.com 25-Z. 7 Change PWB-IC. 8 Change PWB-C.

C0900

Tray3 Elevator failure

1 Check the M101 connector for proper connection and correct as necessary. 2 Check the connector of M101 for proper drive coupling and correct as necessary. 3 PC105 I/O check PWB-Z PJ6Z-3 (ONcopyir.com 2-Y. 4 M101 operation check PWB-Z PJ4Z-4 (+copyir.com PWB-Z PJ4Z-5 (-copyir.com 2-U. 5 Change PWB-Z.

C0910

Tray2 Elevator failure
• The Lift-up Sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started.

 

C0950

Tray4 Elevator failure

 

C0960

Bypass lifting motion failure
• The Bypass Lift-up Sensor is not blocked even when the Tray2 Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the standby position to the take-up position was started. • The Bypass Lift-up Sensor is not unblocked even when the Tray2 Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the take-up position to the standby position was started.

1 Check the M103 connector for proper connection and correct as necessary. 2 Check the connector of M103 for proper drive coupling and correct as necessary. 3 PC115 I/O check PWB-Z PJ7Z-11A (ONcopyir.com 2-E 4 CL101 operation check. 5 M103 operation check PWB-Z PJ5Z-5-8 (Pulse Outputcopyir.com 2-V. 6 Change PWB-Z.

C0990

LCT Elevator Motor malfunction (Elevator malfunctioncopyir.com

 

C0991

LCT ascent motion failure (soft limit errorcopyir.com

 

C0996

LCT Shift Motor malfunction

 

C0997

LCT shifting failure

 

C0998

LCT ejection failure

 

C099C

LCT Shift Gate malfunction

 

C099D

LCT communications error

 

C0B00

Finishing option transport system malfunction

 

C0B05

Finishing option Paddle Motor malfunction

 

C0B20

Finishing option Stapler Unit CD drive failure

 

C0B25

Finishing option Stapler Unit Slide Motor malfunction

 

C0B30

 
نوع وسیله استوک
کاربری لیزری
سرعت چاپ 35 برگ در دقیقه
دقت 600Dpi
تعداد رنگ 4 رنگ
سطح چاپ A4, A3, A5, B4
سال تولید 2005
کشور سازنده چین, ژاپن, کانادا, فرانسه, آلمان, هلند, آمریکا
لارج باکس اختیاری
برد پرینتر دارد
فکس دارد
اسکن به فایل(Scan To File) دارد
کاربری دوکاره
قابلیت تغذیه خودکار(ADF) دارد
قابلیت چاپ دو رو دارد
قابلیت کپی دارد
کارکرد کارتریج مشکی 200000
نوع پورت ارتباطی USB 2
نظرات

 آدرس: آذربایجان شرقی، مراغه، شهرک صنعتی خانقاه، واحد 7، شرکت کپی ایران
شماره تماس: 04137252392
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: Info@copyir.com   |  ساعات کاری: از 8 الی 22

Map Data
Map data ©2017 Google
Map DataMap data ©2017 Google
Map data ©2017 Google
Map
Satellite


فرم تماس با ما

تضمین بهترین قیمت
 
تضمین بهترین قیمت چیست؟

ما تضمین می‌کنیم محصولات عرضه شده در کپی ایران با گارانتی اصل، بالاترین کیفیت و ارزان‌ترین قیمت نسبت به سایر فروشگاه‌های فیزیکی و اینترنتی در سراسر کشور است. اگر پس از خرید از کپی ایران، متوجه شدید فروشگاهی همان کالا را با شرایط یکسان و قیمتی پایین‌تر ارائه می‌دهد، می‌توانید درخواست استفاده از «تضمین بهترین قیمت» را ارسال و در صورت تایید، اختلاف قیمت آن را به طور کامل از ما دریافت کنید.
چه شرایطی دارد؟

برای ارائه درخواست تضمین بهترین قیمت باید شرایط زیر وجود داشته باشد:

    مدل یکسان: محصولات باید از نظر ویژگی‌های فنی، رنگ، امکانات و قابلیت‌ها یکسان باشند.
    کالای اصل: از آنجایی که همه کالاهای موجود در کپی ایران اصل هستند، درخواست کالاهای غیر اصل رد خواهد شد.

3. گارانتی اصل و یکسان: کالاهای مورد مقایسه باید گارانتی و خدمات پس از فروش اصل و یکسان داشته باشند، زیرا نوع و کیفیت خدمات گارانتی‌های مختلف بر قیمت آنها نیز تاثیر می‌گذارد.

    لوازم جانبی اصلی در بسته‌بندی کارخانه: کپی ایران همه لوازم و قطعات همراه کالا که از طرف شرکت سازنده ارائه می‌شود را بدون تغییر یا کم و کاستی به مشتری تحویل می‌دهد. بنابراین محصولاتی که در سایر فروشگاه‌ها ارائه می‌شوند، در صورتی امکان مقایسه خواهند داشت که لوازم جانبی و قطعات اصل و با کیفیت به همراه داشته باشند.

5. یکسانی شرایط برای کالاهایی که دارای تاریخ تولید یا انقضا هستند، شامل تاریخ مصرف نیز می‌شود.

    فروشگاه‌ها و وب‌سایت‌های مجاز: مرجع مقایسه قیمت باید فروشگاه مجاز و وب‌سایت دارای نماد اعتماد الکترونیک از وزارت صنعت معدن و تجارت باشد.
    کالا برای فروش موجود باشد: کالا باید در زمان ارائه درخواست به کپی ایران در سایت یا فروشگاه موردنظر برای فروش موجود و قابل خریداری باشد.

8. با توجه به رسمی بودن فاکتورهای کپی ایران، فاکتور فروشگاه فیزیکی یا اینترنتی مورد مقایسه نیز باید رسمی و دارای کد اقتصادی و 9% مالیات بر ارزش افزوده باشد.

9. با توجه به لزوم یکسان بودن شرایط مقایسه، اگر لحاظ کردن مواردی مانند هزینه حمل و نقل یا مالیات بر ارزش افزوده، قیمت اولیه اعلام شده توسط فروشنده یا فروشگاه اینترنتی مورد مقایسه را تغییر دهد، ملاک مقایسه قیمت کپی ایران، مبلغ نهایی پرداخت شده توسط خریدار خواهد بود.

10.درمورددستگاهای استوک ملاک شرایط مذبور می باشد .

1.مدل دستگاه

2.آپشن های مورد نظر

3.کارکرد دستگاه یعنی دارای شناسنامه باشد که دستگاه مذبور در کجا کار کرده وچه قطعاتی در چه کارکردی تعویض شده است

4.زمان فروش مواد مصرفی آکبند برای شما تحویل داده شده است یا خیر

چگونه درخواست بفرستید؟

مدارک زیر را همراه فاکتور خود، به آدرس ایمیل www.copyir@yahoo.comارسال کنید:

1. پیش‌فاکتور فروشگاه به صورت عکس یا فایل اسکن شده؛ پیش فاکتور باید:

- شامل نام فروشگاه، اطلاعات تماس، آدرس و مهر فروشگاه، نام خریدار، تاریخ و مدت اعتبار پیش فاکتور، اطلاعات محصول و نام گارانتی مربوط به آن باشد.

- تا 24 ساعت بعد از زمان ارسال ایمیل توسط مشتری دارای اعتبار  و کالا در آن فروشگاه موجود و قابل خریداری باشد.

- صرفا برای همان محصول به صورت تکی باشد.

2. در فروشگاه‌های اینترنتی، کافی‌ست آدرس فروشگاه اینترنتی و لینک مستقیم صفحه کالای مورد مقایسه به آدرس ایمیل ذکر شده ارسال شود. بدیهی است که اگر به وب سایت‌های مرجع مقایسه قیمت لینک داده شود، ایمیل ارسالی قابل بررسی نخواهد بود.

چه زمانی درخواست بفرستید؟

درخواست مشتری باید حداکثر تا 48 ساعت بعد از فاکتور شدن سفارش، ارسال شود.

بررسی ثبت درخواست تا حداکثر 3 روز کاری انجام می‌شود.

پس از ارسال استعلام و در صورت تایید قیمت پایین‌تر، اضافه مبلغ پرداخت شده را به حساب شخص واریز می‌کنیم.

سوال دارید؟

با شماره تلفن 04136589016 – داخلی 8 (خدمات پس از فروش) تماس بگیرید.
 
قوانین

در صورت مشاهده تخلف یا تلاش برای سوءاستفاده از این طرح، حق عدم پذیرش آن درخواست برای کپی ایران محفوظ است.

کپی ایران می‌تواند در هر زمان به تشخیص خود شرایط تضمین بهترین قیمت را تغییر داده یا ارائه آن را متوقف کند

 

 

    • ایرادات فتوکپی رنگی 450 بر اساس کد می باشد ما برا ی سهولت کار بران تمامی کدهای را در اختیار عزیزان قرار می دهیم
    • C0000    Main Motor's failure to turn
      • The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turningcopyir.com    1 Check the M1 connector for proper connection and correct as necessarycopyir.com 2 Check M1 for proper drive coupling and correct as necessarycopyir.com 3 Check the PWB-MC connector for proper connection and correct as necessarycopyir.com PWB-MC PJ6MC-1 (DC24 Vکپی ایران 15-R 4 M1 operation check PWB-MC PJ11MC-6A (LOCKکپی ایران PWB-MC PJ11MC-3A (REMکپی ایران 6-Qcopyir.com 5 Change PWB-MCcopyir.com 6 Change PU1copyir.com
      C0001    Main Motor turning at abnormal
Copyright MAXXmarketing Webdesigner GmbH
Google Analytics Alternative