ADU motor rotation abnormal C06 Feed motor rotation abnormal C0A Developer motor rotation abnormal C11 ADU paper side guide operation abnormal C12 ADU paper end guide operation abnormal C13 1st cassette tray operation abnormal C14 2nd cassette tray operation abnormal C15 3rd cassette tray operation abnormal C16 4th cassette tray operation abnormal C18 LCF tray operation abnormal C27 Carriage home position sensor not turning OFF within a fixed time C28 Carriage home position sensor not turning ON within a fixed time C29 Exposure lamp disconnection detected C31 Used toner transport motor rotation abnormal C33 Developer removal shutter abnormal C35 Transfer belt unit contact/release operation abnormal C38 Auto-toner error (K) C39 Auto-toner error (C) C3A Auto-toner error (M) Copyir.com C05 ADU motor rotation abnormal C06 Feed motor rotation abnormal C0A Developer motor rotation abnormal C11 ADU paper side guide operation abnormal C12 ADU paper end guide operation abnormal C13 1st cassette tray operation abnormal C14 2nd cassette tray operation abnormal C15 3rd cassette tray operation abnormal C16 4th cassette tray operation abnormal C18 LCF tray operation abnormal C27 Carriage home position sensor not turning OFF within a fixed time C28 Carriage home position sensor not turning ON within a fixed time C29 Exposure lamp disconnection detected C31 Used toner transport motor rotation abnormal C33 Developer removal shutter abnormal C35 Transfer belt unit contact/release operation abnormal C38 Auto copyir.comtoner error (K) C39 Auto copyir.comtoner error (C) C3A Auto copyir.comtoner error (M) C3B Auto copyir.comtoner error (Y) C3C Main charger wire cleaning abnormal (K) C3D Main charger wire cleaning abnormal (C) C3E Main charger wire cleaning abnormal (M) C3F Main charger wire cleaning abnormal (Y) C41 Thermistor or heater abnormal when warming copyir.comup is started C42 Thermistor abnormal after the copier has become ready C43 Thermistor abnormal during warming copyir.comup after abnormality judgment C44 Heater abnormal during warming copyir.comup after abnormality judgment C46 Heater abnormal (low temperature) after the copier has become ready C47 Rear thermistor abnormal after the copier has become ready C48 Heater abnormal (high temperature) C57 Communications error between LGC copyir.comCPU and IPC board C5A Communications error between LGC copyir.comCPU and printer controller C5B LGC copyir.comCPU signal transmission error to IMC copyir.comCPU C5C LGC copyir.comCPU signal reception error from IMC copyir.comCPU C7 Error C7 C72 Aligning sensor automatic adjustment error C73 EEPROM initializing error C74 Paper exit sensor automatic adjustment error C82 Communications error between scanner and ADF C94 LGC copyir.comCPU abnormal C9A Main memory abnormal C9B LGC copyir.comCPU protocol abnormal C9D IMC copyir.comCPU protocol abnormal C9E IMC board connection abnormal CA1 Polygonal motor rotation abnormal CA2 H copyir.comSYNC abnormal CB1 Feed motor abnormal CB2 Delivery motor abnormal CB3 Tray lift motor abnormal CB4 Alignment motor abnormal CB5 Staple motor abnormal CB6 Stapler shift motor abnormal CB7 Height sensor abnormal CB8 Backup RAM data abnormal CB9 Saddle stitcher/paper pushing plate motor abnormal CBA Saddle stitcher/stitcher motor (front) abnormal CBB Saddle stitcher/stitcher motor (rear) abnormal CBC Saddle stitcher/alignment motor abnormal CBD Saddle stitcher/guide motor abnormal CBE Saddle stitcher/paper folding motor abnormal CBF Saddle stitcher/paper positioning plate motor abnormal CD1 Laser calibration error (K) CD2 Laser calibration error (C) CD3 Laser calibration error (M) CD4 Laser calibration error (Y) CD5 Saddle stitcher/sensor connector connection error CD6 Saddle stitcher/microswitch abnormal CD7 Communication error between finisher and saddle stitcher CD9 Swing motor abnormal CDA Horizontal registration motor abnormal CDB Punch motor abnormal CE1 Image quality sensor abnormal (OFF level) CE2 Image quality sensor abnormal (no pattern level) CE3 Abnormal image caused by poor charge CE4 Image quality control test pattern abnormal CE5 Temperature/humidity sensor upper copyir.comlimit abnormal CE6 Drum thermistor abnormal (Y) CE9 Drum thermistor abnormal (K) CF1 Color registration control abnormal E01 Paper leading edge not reaching the exit sensor E02 Paper trailing edge not passing the exit sensor E03 Paper remaining inside the copier at power ON E11 Paper misfeed from the ADU E12 Paper misfeed from the bypass tray E13 Paper misfeed from the 1st cassette E14 Paper misfeed from the 2nd cassette E15 Paper misfeed from the 3rd cassette E16 Paper misfeed from the 4th cassette E19 Paper misfeed from the LCF E21 Paper transport jam from the LCF E22 Paper transport jam from the 1st cassette E23 Paper transport jam from the 2nd cassette E24 Paper transport jam from the 3rd cassette E25 Paper transport jam from the 4th cassette E26 Paper transport jam from the bypass tray E41 Front cover opened during printing E42 Side door opened during printing E43 ADU pulled out during printing E45 LCF jam access cover opened during printing E46 Bypass unit opened during printing E50 Paper not reaching the ADU E51 Paper not restarting from the ADU stack E52 Paper not reaching the ADU path sensor E54 ADU paper transport jam E71 Original not reaching the aligning sensor E72 Original not reaching the exit sensor E73 Original not passing the exit sensor E79 Original pre copyir.comfeed jam E9F Punching jam EA1 Paper transport delay jam EA2 Paper transport stop jam EA3 Paper remaining inside the finisher at power ON EA4 Finisher front door opened during printing EA5 Finisher stapling jam EA6 Finisher early arrival jam EA8 Saddle stitcher stapling jam EA9 Saddle stitcher front door opened during printing EAA Paper remaining in the saddle stitcher at power ON EAB Saddle stitcher transport stop jam EAC Saddle stitcher transport delay jam EAE Finisher receive time copyir.comout jam EB7 Restart time copyir.comout error EC2 OHP film jams when not fed from bypass tray or 2nd cassette EC3 OHP film used in non copyir.comOHP mode F07 Communications error between system copyir.comCPU and LGC copyir.comCPU F09 Communications error between system copyir.comCPU and scanner copyir.comCPU F10 HDD formatting error F11 Communications error between system copyir.comCPU and scanner copyir.comCPU F12 Communications error between system copyir.comCPU and scanner copyir.comCPU F13 Communications error between system copyir.comCPU and LGC copyir.comCPU F51 Communications error between system copyir.comCPU and AI board during pre copyir.comscanning
Main motor abnormality: The main motor is not rotating normally copyir.com C020 Developer drive motor abnormality: The developer drive motor is not rotating normally copyir.com C030 Transport motor abnormality: The transport motor is not rotating normally copyir.com C040 PFP motor abnormality: The PFP motor is not rotating normally copyir.com (the case that paper can be fed from any drawer except the PFP) C130 1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 1st drawer) C140 2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 2nd drawer) C150 PFP upper drawer tray abnormality: The PFP upper drawer tray-up motor is not rotating or the PFP upper drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the PFP upper drawer) C160 PFP lower drawer tray abnormality: The PFP lower drawer tray-up motor is not rotating or the PFP lower drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the PFP lower drawer) C180 LCF tray-up motor abnormality: The LCF trayup motor is not rotating or the LCF tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the LCF) C1A0 LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally copyir.com (the case that paper can be fed from any drawer except the LCF) C1B0 LCF transport motor abnormality: The LCF transport motor is not rotating normally (when paper can be fed from any drawer except the LCF) copyir.com C260 Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON copyir.com C270 (1) Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time copyir.com (2) Downloading firmware with an incorrect model copyir.com If the error occurs, the exposure lamp lights twice at the same time copyir.com C280 Carriage home position sensor not going ON within a specified time C360 Charger cleaner motor abnormality: Charger cleaner motor is not rotating or wire cleaner is not moving normally C411 Thermistor or heater lamp abnormality at power-ON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser roller does not rise in a specified period of time after power is turned ON copyir.com C412 Thermistor/heater lamp abnormality at power- ON: Thermistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a specified period of time after power-ON copyir.com C443 Heater lamp abnormality after abnormality judgment (not reaching to intermediate temperature) C445 Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality) C446 Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality) C447 Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status) C448 Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified C471 IH power voltage abnormality or IH initial abnormality (IH board initial abnormality) C472 IH power voltage abnormality (power supply abnormality) C475 IH power voltage abnormality (power supply abnormality when door is opened) C480 Overheating of IGBT: The temperature of the IGBT rises abnormally copyir.com C490 IH control circuit or IH coil abnormality: Abnormality is detected in IH control circuit or IH coil is broken/ shorted copyir.com C4B0 Fuser unit counter abnormality C550 RADF I/F error: Communication error has occurred between the RADF and the scanner copyir.com C570 Communication error between Engine-CPU and IPC board C580 Communication error between IPC board and finisher C900 Connection error between SYS board and LGC board C940 Engine-CPU abnormality C950 LGC board memory abnormality C960 Connection error between LGC board and DRV board, ID abnormality C970 High-voltage transformer abnormality: Leakage of the main charger is detected copyir.com C9E0 Connection error between SLG board and SYS board CA10 Polygonal motor abnormality: The polygonal motor is not rotating normally copyir.com CA20 H-Sync detection error: H-Sync signal detection PC board cannot detect laser beams copyir.com CB20 Delivery motor abnormality: Delivery motor or delivery roller is not rotating normally copyir.com [MJ-1022] CB30 Tray 1/Tray 2 shift motor abnormality: Tray 1/Tray 2 shift motor is not rotating or delivery tray is not moving normally copyir.com [MJ-1023/1024] CB40 Rear aligning plate motor abnormality: Rear aligning plate motor is not rotating or aligning plate is not moving normally copyir.com [MJ-1023/1024] CB50 Staple motor abnormality: Staple motor is not rotating or stapler is not moving normally copyir.com [MJ-1022/ 1023/1024] CB80 Backup RAM data abnormality: 1) Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON copyir.com [MJ-1023/1024] 2) Abnormality of checksum value on punch controller PC board is detected when the power is turned ON copyir.com [MJ-1023/1024 (when MJ-6004 is installed)] CB90 Paper pushing plate motor abnormality: Paper pushing plate motor is not rotating or paper pushing plate is not moving normally copyir.com [MJ-1024] CBA0 Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally copyir.com [MJ-1024] CBB0 Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally copyir.com [MJ-1024] CBC0 Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally copyir.com [MJ-1024] CBD0 Guide motor abnormality: Guide motor is not rotating or guide is not moving normally copyir.com [MJ-1024] CBE0 Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally copyir.com [MJ-1024] CC00 Sensor connector abnormality: Connector of guide home position sensor, paper pushing plate home position sensor or paper pushing plate top position sensor is disconnected copyir.com [MJ-1024] CC10 Micro switch abnormality: With all covers closed, inlet door switch, delivery door switch or front cover switch is open copyir.com [MJ-1024] CC20 Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1023/1024] CC30 Stack processing motor abnormality: The stack processing motor is not rotating or the stack delivery belt is not moving normally copyir.com [MJ-1022] CC40 Swing motor abnormality: Swing motor is not rotating or swing unit is not moving normally copyir.com [MJ-1023/ 1024] CC50 Horizontal registration motor abnormality: Horizontal registration motor is not rotating or puncher is not shifting normally copyir.com [MJ-1023/1024 (when MJ- 6004 is installed)] CC60 Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally copyir.com [MJ-1023/ 1024 (when MJ-6004 is installed)] CC80 Front alignment motor abnormality: Front alignment motor is not rotating or front aligning plate is not moving normally copyir.com [MJ-1022] Front aligning plate motor abnormality: Front aligning plate motor is not rotating or aligning plate is not moving normally copyir.com [MJ-1023/1024] CC90 Upper stack tray lift motor abnormality: The upper stack tray lift motor is not rotating or the upper stack tray is not moving normally copyir.com [MJ-1022] CCA0 Lower stack tray lift motor abnormality: The lower stack tray lift motor is not rotating or the lower stack tray is not moving normally copyir.com [MJ-1022] CCB0 Rear jogging motor abnormality: The rear jogging motor is not rotating or the rear jogging plate is not moving normally copyir.com [MJ-1022] CCD0 Stack ejection motor abnormality: Stack ejection motor or stack ejection roller is not rotating normally copyir.com [MJ-1023/1024] CCE0 Paper trailing edge assist motor abnormality: Paper trailing edge assist motor is not rotating or paper trailing edge assist is not moving normally copyir.com [MJ- 1023/1024] CCF0 Gear changing motor abnormality: Gear changing motor is not rotating normally copyir.com [MJ-1023/1024] CE00 Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board [MJ- 1023/1024 (when MJ-6004 is installed)] CE10 Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF copyir.com CE20 Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed copyir.com CE40 Image quality control test pattern abnormality: The test pattern is not formed normally copyir.com CE50 Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range copyir.com CE90 Drum thermistor abnormality: The output value of the drum thermistor is out of a specified range copyir.com CEA0 Revolver home position detection abnormality: It cannot detect that the revolver is at its home position copyir.com CEB0 Black developer unit lifting movement abnormality: The black developer unit does not move up or down normally (lifting cam does not operate normally) copyir.com CEC0 2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally copyir.com CEE0 Transfer belt position detection abnormality (normal speed): The home position of the transfer belt cannot be detected copyir.com CEE1 Transfer belt position detection abnormality (when decelerating): Reference position of the transfer belt cannot be detected copyir.com CEF0 Revolver motor abnormality: Revolver motor is not rotating or revolver is not moving normally copyir.com CF20 Toner density detection voltage abnormality: The output value of the color auto-toner sensor in printing is out of a specified range copyir.com CF30 Reference plate detection voltage abnormality: The output value of the color auto-toner sensor against the reference plate is out of a specified range at the light amount correction during an auto-toner adjustment or when a print job has finished copyir.com CF30 Reference plate detection voltage abnormality: The output value of the color auto-toner sensor against the reference plate is out of a specified range at the light amount correction during an auto-toner adjustment or when a print job has finished copyir.com CF40 Light amount correction voltage abnormality: The light amount correction is not finished normally during an auto-toner adjustment or when a print job has finished, or the output value of the sensor is out of a specified range when the light amount correction has finished copyir.com CF50 Color auto-toner sensor abnormality: The connection of the color auto-toner sensor cannot be detected at the initialization, or the output value of color auto-toner sensor when the revolver starts rotating for initialization is out of a specified range copyir.com E010 Jam not reaching the exit sensor: The paper which has passed through the fuser unit does not reach the exit sensor copyir.com E020 Stop jam at the exit sensor: The trailing edge of the paper does not pass the exit sensor after its leading edge has reached this sensor copyir.com E030 Power-ON jam: The paper is remaining on the paper transport path when power is turned ON copyir.com E061 Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment copyir.com E062 Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment copyir.com E063 Incorrect paper size setting for PFP upper drawer: The size of paper in the 3rd drawer differs from size setting of the equipment copyir.com E064 Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment copyir.com E065 Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment copyir.com E090 Image data delay jam: Image data to be printed cannot be prepared E110 ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing copyir.com E120 Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor copyir.com E130 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor copyir.com E140 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor copyir.com E150 PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor copyir.com E160 PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed sensor copyir.com E190 LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor copyir.com E200 1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com E210 2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com E220 2nd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir.com E300 PFP upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com E310 PFP upper drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir.com E320 PFP upper drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the PFP upper drawer feed sensor copyir.com E330 PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com E340 PFP lower drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir.com E350 PFP lower drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the PFP upper drawer feed sensor copyir.com E360 PFP lower drawer transport jam (Paper not reaching the PFP upper drawer feed sensor): The paper does not reach the PFP upper drawer feed sensor after it has passed the PFP lower drawer feed sensor copyir.com E400 Jam access cover open jam: The jam access cover has opened during printing copyir.com E410 Front cover open jam: The front cover has opened during printing copyir.com E420 PFP side cover open jam: The PFP side cover has opened during printing copyir.com E430 ADU open jam: The ADU has opened during printing copyir.com E440 Side cover open jam: The side cover has opened during printing copyir.com E450 LCF side cover open jam: The LCF side cover has opened during printing copyir.com E480 Bridge unit open jam: The bridge unit has opened during printing copyir.com E510 Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section copyir.com E520 Stop jam in the ADU: The paper does not reach the ADU exit sensor after it has passed the ADU entrance sensor copyir.com E550 Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished copyir.com E712 Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor E714 Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray copyir.com E721 Jam not reaching the read sensor: The original does not reach the read sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side) copyir.com E722 Jam not reaching the original exit/reverse sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section copyir.com E724 Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor copyir.com E725 Stop jam at the read sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor copyir.com E731 Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor copyir.com E860 RADF jam access cover open: The RADF jam access cover has opened during RADF operation copyir.com E870 RADF open jam: RADF has opened during RADF operation E871 Cover open jam in the read ready status E910 Jam at the bridge unit transport sensor 1: The paper does not reach the bridge unit transport sensor 1 after it has passed the exit sensor copyir.com E920 Stop jam at the bridge unit transport sensor 1: The trailing edge of the paper does not pass the bridge unit transport sensor 1 after its leading edge has reached the sensor copyir.com E930 Jam at the bridge unit transport sensor 2: The trailing edge of the paper does not reach the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 1 copyir.com E940 Stop jam at the bridge unit transport sensor 2: The trailing edge of the paper does not pass the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 2 copyir.com E9F0 Punching jam: Punching is not performed properly copyir.com EA10 Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor copyir.com[MJ-1031/1101] The paper which has passed the bridge unit does not reach the inlet sensor copyir.com EA20 Paper transport stop jam: The paper does not pass through the inlet sensor copyir.com The paper which has passed through the inlet sensor does not reach the feeding sensor copyir.com EA30 Power-ON jam: Paper exists at the inlet sensor when power is turned ON copyir.com EA40 Joint open jam: The finisher cover opened during machine operation copyir.com Cover open error: The front cover or stationary tray is opened during paper transport copyir.com EA50 Stapling jam: Stapling is not performed properly copyir.com EA60 Early arrival jam: The inlet sensor detects the paper earlier than a specified timing copyir.com EA70 Stack exit belt home position error: The stack exit belt is not at the home position copyir.com Stack slider home position error: The stack slider is not at the home position copyir.com EA80 Stapling jam: Stapling is not performed properly copyir.com [MJ-1024] EA90 Door open jam: The delivery cover or inlet cover has opened dur-ing printing [MJ-1024] copyir.com EAA0 Power-ON jam: Paper exists at No copyir.com1 paper sensor, No copyir.com 2 paper sensor, No copyir.com3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON copyir.com [MJ-1024] EAB0 Transport stop jam: The paper which passed through the inlet sensor does not reach or pass No copyir.com1 paper sensor, No copyir.com 2 paper sensor, No copyir.com3 paper sensor or delivery sensor copyir.com [MJ-1024] EAC0 Transport delay jam: The paper which has reached the inlet sensor does not pass through the inlet sensor copyir.com [MJ-1024] EAD0 Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing copyir.com EAE0 Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher copyir.com EAF0 Stack return jam: It cannot load the paper which passed through the delivery roller on the intermediary process tray copyir.com [MJ-1022] EB50 Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper copyir.com EB60 Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]) copyir.com F070 Communication error between System-CPU and Engine-CPU F090 SRAM abnormality on the SYS board F091 NVRAM abnormality on the SYS board 092 SRAM and NVRAM abnormality on the SYS board F100 HDD format error: HDD cannot be initialized normally copyir.com F101 HDD unmounted: Connection of HDD cannot be detected copyir.com F102 HDD start error: HDD cannot become ‘Ready’ state copyir.com F103 HDD transfer time-out: Reading/writing cannot be performed in the specified period of time copyir.com F104 HDD data error: Abnormality is detected in the data of HDD copyir.com F105 HDD other error F106 Point and Print partition damage F107 /BOX partition damage F108 /SHA partition damage F110 Communication error between System-CPU and Scanner-CPU F111 Scanner response abnormality F120 Database abnormality: Database is not operating normally copyir.com F130 Invalid MAC address F200 Data overwrite kit (GP-1060) is taken off F350 SLG board abnormality
