توشیبا Toshiba DP5510

ایرادات دستگاههای توشیبا براساس کد می باشد. شرکت کپی ایران در نظر دارد تمامی سرویس مانوئلها و رفع ایرادات را در اختیار شما عزیزان قرار دهد.

 

C04    Abnormal feed motor
C13    Abnormal 1st cassette tray (Paper can be fed from cassettes other than the 1st cassette  copyir.com)
C14    Abnormal 2nd cassette tray (Paper can be fed from cassettes other than the 2nd cassette  copyir.com)
C15    Abnormal 3rd cassette tray (Paper can be fed from cassettes other than the 3rd cassette  copyir.com)
C16    Abnormal 4th cassette tray (Paper can be fed from cassettes other than the 4th cassette  copyir.com)
C18    Abnormal tandem LCF tray-up motor (Paper can be fed from cassettes other than the tandem LCF cassette  copyir.com)
C1A    Abnormal tandem LCF end fence motor (Paper can be fed from cassettes other than the tandem LCF cassette  copyir.com)
C1C    Abnormal external LCF tray-up motor (Paper can be fed from cassettes other than the external LCF)
C26    Peak detection error
C27    Carriage home position sensor not going OFF within a fixed time
C28    Carriage home position sensor not going ON within a fixed time
C36    Abnormal main charger wire cleaner drive motor
C37    Abnormal transfer belt cam motor
C41    Abnormal thermistor or heater at the power ON
C43    Abnormal thermistor after abnormality judgment
C44    Abnormal fuser after abnormality judgment
C45    Abnormal side thermistor after the copier has become ready
C46    Abnormal pressure roller thermistor during a ready state
C47    Abnormal IH power voltage / IH initialization error
C48    IGBT high temperature
C49    Abnormal IH circuit or coil
C4A    Cleaning web finished
C55    RADF I/F error
C56    Communication error between main CPU and PFC
C57    Communication error between main CPU and IPC board
C58    Communication error between IPC board and finisher
C59    Communication error between main CPU and laser CPU
C73    EEPROM initialization error
C82    Read sensor adjustment error
C83    Original length sensor adjustment error
C84    Small original reverse sensor adjustment error
C85    Abnormal tray lift motor
C86    Large original exit sensor adjustment error
C94    Abnormal main CPU
CA1    Abnormal polygonal motor
CA2    H-Sync detection error
CA3    Secondary scanning coarse adjustment error
CA5    Laser power adjustment error
CA6    Laser calibration error
CA9    Image data transmission error from SYS board
CAA    Secondary scanning fine adjustment error
CAB    Secondary scanning inter-page compensation error
CAC    Primary scanning dot adjustment error
CB1    Abnormal feed motor
CB2    Abnormal delivery motor
CB3    Abnormal tray lift motor
CB4    Abnormal alignment motor
CB5    Abnormal staple motor
CB6    Abnormal stapler shift motor
CB7    Abnormal height sensor
CB8    Abnormal backup RAM data
CB9    Abnormal saddle stitcher paper pushing plate motor
CBA    Abnormal saddle stitcher stitch motor (front)
CBB    Abnormal saddle stitcher stitch motor (rear)
CBC    Abnormal saddle stitcher alignment motor
CBD    Abnormal saddle stitcher guide motor
CBE    Abnormal saddle stitcher paper folding motor
CBF    Abnormal saddle stitcher paper positioning plate moto
CC0    Abnormal saddle stitcher sensor connector connection
CC1    Abnormal saddle stitcher microswitch
CC2    Abnormal communication between finisher and saddle stitcher
CC4    Abnormal swing motor
CC5    Abnormal horizontal registration motor
CC6    Abnormal punch motor
CC7    Abnormal punch unit backup RAM data
CCC    Communication error between inserter and finisher
CCD    Abnormal inserter EEPROM
CCE    Abnormal inserter fan
CD0    Laser initializing time out
CD1    Abnormal drum cleaning brush motor
CD2    Abnormal used toner transport motor
CD3    Abnormal recycle toner transport motor
CD4    Full toner bag
CD5    Web motor signal path error
CE0    Abnormal comparator
CE1    Beam sensor detection error
CE2    Sensor busy error
CE3    Primary scanning adjustment error
CE4    Abnormal window comparator
E01    Leading edge of paper not reaching the fuser exit sensor
E02    Trailing edge of paper not passing the fuser exit sensor
E03    Paper remaining inside the copier at power ON
E09    Jam caused by an abnormal HDD
E11    Misfeeding during duplex printing (paper not reaching the registration sensor)
E12    Bypass misfeeding (paper not reaching the registration sensor)
E13    1st cassette misfeeding (paper not reaching the 1st cassette feed sensor)
E14    2nd cassette misfeeding (paper not reaching the 2nd cassette feed sensor)
E15    3rd cassette misfeeding (paper not reaching the 3rd cassette feed sensor)
E16    4th cassette misfeeding (paper not reaching the 4th cassette feed sensor)
E18    Tandem LCF misfeeding (paper not reaching the tandem LCF feed sensor)
E19    External LCF misfeeding (paper not reaching the external LCF feed sensor)
E20    Paper fed from the 1st cassette (not reaching the registration sensor)
E21    Paper fed from the 1st cassette (not reaching the 1st cassette transport sensor)
E22    Paper fed from the 2nd cassette (not reaching the registration sensor)
E23    Paper fed from the 2nd cassette (not reaching the 1st cassette transport sensor)
E24    Paper fed from the 2nd cassette (not reaching the 2nd cassette transport sensor)
E25    Paper fed from the external LCF (not reaching the registration sensor)
E30    Paper fed from the 3rd cassette (not reaching the registration sensor)
E31    Paper fed from the 3rd cassette (not reaching the 1st cassette transport sensor)
E32    Paper fed from the 3rd cassette (not reaching the 2nd cassette transport sensor)
E33    Paper fed from the 3rd cassette (not reaching the 3rd cassette transport sensor)
E34    Paper fed from the 4th cassette (not reaching the registration sensor)
E35    Paper fed from the 4th cassette (not reaching the 1st cassette transport sensor)
E36    Paper fed from the 4th cassette (not reaching the 2nd cassette transport sensor)
E37    Paper fed from the 4th cassette (not reaching the 3rd cassette transport sensor)
E38    Paper fed from the 4th cassette (not reaching the 4th cassette transport sensor)
E3C    Paper fed from the tandem LCF (not reaching the registration sensor)
E3D    Paper fed from the tandem LCF (not reaching the 1st cassette feed sensor)
E3E    Paper fed from the tandem LCF (not reaching the 2nd cassette feed sensor)
E3F    Paper fed from the tandem LCF (not reaching the tandem LCF transport sensor)
E41    Front cover opened during printing
E44    Feed cover opened during printing
E45    LCF side cover opened during printing
E46    Bypass feed unit cover opened during printing
E47    Exit cover opened during printing
E50    Leading edge of paper not reaching the reverse sensor 2
E51    Leading edge of paper not reaching the transport sensor 1
E52    Leading edge of paper not reaching the transport sensor 2
E54    Leading edge of paper not reaching the transport sensor 3
E55    Paper remaining on the transport path when CRUN is OFF
E57    Leading edge of paper not reaching the reverse sensor 1
E58    Trailing edge of paper not passing the reverse sensor 1 or reverse sensor 2
E59    Trailing edge of paper not passing the exit sensor
E5A    Leading edge of paper not reaching the exit sensor
E71    Original feeding jam
E72    Original transport jam
E73    Original discharging jam
E74    Original reversing jam
E76    Small original discharging jam
E77    Scanning section transport jam
E7B    RADF opened at the original transporting
E7C    RADF opened at the large original discharging
E7D    RADF opened at the small original reversing
E7E    RADF opened at the small original discharging
E7F    RADF opened at the original scanning section
E80    Jam access cover opened at the original feeding
E81    Jam access cover opened at the original transporting
E82    Jam access cover opened at the large original dischaging
E83    Jam access cover opened at the small original reversing
E84    Jam access cover opened at the small original discharging
E85    Jam access cover opened at the original scanning section
E9F    Punching jam
EA1    Finisher paper transport delay jam
EA2    Finisher paper transport stop jam
EA3    Paper remaining inside the finisher at power ON
EA4    Finisher front door opened during printing
EA5    Finisher stapling jam
EA6    Finisher early arrival jam
EA7    Stack transport jam before stapling
EA8    Saddle stitcher stapling jam
EA9    Saddle stitcher door opened during printing
EAA    Paper remaining at the saddle stitcher at power ON
EAB    Saddle stitcher paper transport stop jam
EAC    Saddle stitcher paper transport delay jam
EAD    Print end command time-out jam
EAE    Receiving time time-out jam
EB3    Ready time time-out jam
EB5    Paper left on the transport path
EB6    Paper left on the transport path
EC0    Inserter feeding delay jam
EC1    Inserter feeding stop jam
EC2    Inserter reverse path delay jam 1
EC3    Inserter reverse path stop jam 1
EC4    Inserter reverse path delay jam 2
EC5    Inserter reverse path stop jam 2
EC6    Inserter transport delay jam 1
EC7    Inserter transport stop jam 1
EC8    Inserter transport delay jam 2
EC9    Inserter transport stop jam 2
ECA    Paper remaining in the inserter when power is ON
ECB    Wrong size of inserter
ECC    Inserter feeding Jam
F07    Communication error between SYS board and LGC board
F10    HDD formatting error
F11    Communication error between SYS board and SLG board

پست های مرتبط

دیدگاهتان را بنویسید

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

جستجو در مطالب

سوالی دارید؟

برای آگاهی از راه های ارتباط با ما، بر روی دکمه زیر کلیک کنید

مطالب جدید ...

در خبرنامه ما عضو شوید