T1    Main Motor Lock
• In 3 seconds from turning ON of the Main motor, the A detection sensor light path is still held blocked     copyir.com
• In 8 seconds from turning ON of the Main motor, the A detection sensor is not blocked     copyir.com
T10    Malfunction Image Processing PCB
• When the scanning contrast adjustment signal is not output from the image processing PCB     copyir.com
T11    Pressure Control Motor Lock
• In 100ms from turning ON of the Pressure control motor, the Encoder sensor cannot detect a pulse     copyir.com
• In 5 seconds from turning ON of the Pressure control motor, the Pressure centering sensor is not turned ON/OFF     copyir.com
T12    • Malfunction of Trimming PCB
• When the TOP signal is not output from the Trimming PCB 2
T13    Cutter Motor Lock
• After master cutting retrial with the drum held in C-2 position, when the Master positioning sensor is in light-receiving state     copyir.com (Master cutting has failed in the 2nd time     copyir.com)
T14    Clamp Error (2)
• If the actuator of the Clamp safety switch is not depressed when the Clamp solenoid is not in operation     copyir.com
T15    Flat Bed Read Pulse Motor Lock
• If the Image scanner home position sensor does not detect the Image scanner within 18898 pulses after the Flat bed read pulse motor is activated     copyir.com
• If the Image scanner ADF Shading sensor does not detect the Image scanner within 15748 pulses after the Flat bed read pulse motor is activated     copyir.com • If the scanner home position sensor does not detect the Image scanner within 14,551 pulses(462 mm worth) after the Flat bed read pulse motor is activated during prescanning     copyir.com
• If the Image scanner is not release from the Image scanner home position sensor within 314 pulses after the Flat bed read pulse motor is activated     copyir.com
• If the Image scanner is not released from the Image scanner ADF Shading sensor within 314 pulses after the Flat bed read pulse motor is activated     copyir.com
T16    Position C Sensor Malfunction
• If the Position C sensor status has not been changed from ON to OFF (or OFF to ON) within 8 seconds from the start of the Main Motor     copyir.com
T17    Replace Battery
• When the battery voltage is less than 2     copyir.com4 V at power-on, all reset, or end of operation     copyir.com
T18    Sorter Error
• If an error signal is received from the sorter     copyir.com
T19    Thermal Pressure Motor Lock
• If the TPH Pressure switch has not been depressed within 4 seconds after the TPH Pressure motor was activated to lower the TPH     copyir.com
• If the TPH Pressure switch has not been released within 4 seconds after the TPH Pressure motor was activated to raise the TPH     copyir.com
T2    Elevator Motor Lock
• In 15 seconds from turning ON of the Elevator motor in upward direction, the Elevator upper limit sensor is not pushed     copyir.com
• In 15 seconds from turning ON of the Elevator motor in downward direction, the light path of the Elevator lower limit sensor is not blocked     copyir.com
• In 3 seconds from turning ON of the Elevator motor in upward direction, the Elevator lower sensor is held blocked     copyir.com
• In 3 seconds from turning ON of the Elevator motor in downward direction, the Elevator upper limit sensor is held pressed down     copyir.com
T20    Wing Motor Lock
• If neither of the Jump wing sw1 or sw2 has been depressed within 5 seconds after the Wing motor was activated     copyir.com
• If neither of the Jump wing sw1 or sw2 has been released within 5 seconds after the Wing motor was activated     copyir.com
T3    Clamp Error (1)
• In 4 seconds from turning ON of the Clamp solenoid in clamp retrial, the Clamp safety switch is held still pressed down     copyir.com
• In 4 seconds from turning OFF of the Clamp solenoid, the Clamp safety SW has not been pressed     copyir.com
• In 8 seconds from turning ON of the Clamp motor in opening direction in clamp retrial, the 180° Angular sensor has not detected magnet     copyir.com
• In 8 seconds from turning ON of the Clamp motor in closing direction in clamp retrial, the 0° Angular sensor has not detected magnet     copyir.com
In any of the above cases, master making is performed to the end     copyir.com
T30    P     copyir.com -F     copyir.com Tray Slide Pulse Motor
• When the Paper feed tray position sensor is not turned on/ off within 165 pulses(approx     copyir.com 3 second) after the P     copyir.com -F     copyir.com tray slide pulse motor is turned on     copyir.com
T4    Overflow
• When ink is in contact with the Overflow sensor     copyir.com The Drum set switch need be pushed     copyir.com
T5    Print Positioning Motor Lock
• In 12 seconds from turning ON of the Print positioning motor, the Vertical centering sensor is not turned ON/OFF     copyir.com
T50    Connect “Copy/Master” Counter
• When the copy counter or the master counter has not been connected     copyir.com
T6    Pressure Detection Sensor Malfunction
• In 8 seconds from turning ON of the main motor, the Pressure detection sensor is not turned ON/OFF     copyir.com
T68    SF3000 Power Supply Malfunction
• When no power is supplied to the SF3000     copyir.com
T7    Communication error between FR and Digitizer
• On occurrence of an error in communication between the System PCB and Digitizer III     copyir.com
T78    Machine Model Selection Error
• When there is no machine type which corresponds to the code having been set in System PCB     copyir.com
T79    Destination Spec     copyir.com Code Error
• When the code set (DIP switch) does not match the model set with the Hex     copyir.com switch     copyir.com
T8    Communication error between System PCB and Panel PCB
• On occurrence of an error in communication between the System PCB and the Panel PCB     copyir.com
T9    Communication error between FR and the Sorters
• On occurrence of an error in communication between the System PCB and the Sorter (TM)

اشتراک گذاری در:

پست های مرتبط

دیدگاهتان را بنویسید

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

جستجو در مطالب

سوالی دارید؟

برای آگاهی از راه های ارتباط با ما، بر روی دکمه زیر کلیک کنید

مطالب جدید ...

در خبرنامه ما عضو شوید