ریکوآفشیوRicoh Aficio 1015

ایرادات ریکو براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

401   Transfer roller leak error 1
A current leak signal for the transfer roller is detected ( copyir.com ) A current feedback signal for the transfer roller is not detected ( copyir.com )    • High voltage supply board defective • Poor connection of the PCU • Transfer/separation unit set incorrectly • Transfer roller damaged
402   Transfer roller leak error 2
A current leak signal for the transfer roller is detected ( copyir.com ) A current feedback signal for the transfer roller is not detected ( copyir.com )    • High voltage supply board defective • Poor connection of the PCU • Transfer/separation unit set incorrectly • Transfer roller damaged
500   Main motor lock
A main motor lock signal is not detected for more than 7 consecutive checks (700 ms) after the main motor starts to rotate, or the lock signal is not detected for more than 7 consecutive checks during rotation after the last signal ( copyir.com )    • Too much load on the drive mechanism • Main motor defective
503   Upper paper tray lift motor malfunction (optional paper tray units)
The paper lift sensor fails to activate twice continuously after the tray lift motor has been on for 18 seconds ( copyir.com )    • Paper lift sensor defective • Tray lift motor defective • Too much load on the drive mechanism • Poor tray lift motor connection
504   Lower paper tray lift motor malfunction (optional two-tray paper tray unit)
The paper lift sensor fails to activate twice continuously after the tray lift motor has been on for 18 seconds ( copyir.com )    • Paper lift sensor defective • Tray lift motor defective • Too much load on the drive mechanism • Poor tray lift motor connection
506   Paper feed motor lock (optional paper tray units)
A motor lock signal is not detected for more than 1 ( copyir.com ) 5 s or the lock signal is not detected for more than 1 ( copyir.com ) 0 s during rotation ( copyir.com )    • Paper feed motor defective • Too much load on the drive mechanism
541   Fusing thermostat/thermistor open
The fusing temperature detected by the thermistor is below 10°C for 5 seconds after the main power switch is turned on ( copyir.com )    • Fusing thermostat defective or out of position • Fusing thermistor defective or out of position • Power supply board defective
542   Fusing temperature warm-up error
The fusing temperature does not reach 80°C within 30 seconds after the main switch is turned on ( copyir.com )    • Fusing thermistor defective or out of position • Fusing lamp open • Fusing thermostat open • Fusing thermofuse open • Power supply board defective
543   Fusing overheat error
A fusing temperature of over 230°C is detected for 1 second by the fusing thermistor ( copyir.com )    • Fusing thermistor defective • Power supply board defective
544   Fusing low temperature error
A fusing temperature of lower than 100°C is detected for 1 second by the fusing thermistor during operation or stand-by mode ( copyir.com )    • Fusing lamp open • Fusing thermistor defective • Power supply board defective • Fusing thermistor open • Fusing thermostat open
546   Unstable fusing temperature
The fusing temperature does not rise 3 °C or more within 5 seconds after the fusing lamp has been on over 8 seconds ( copyir.com )    • Thermistor defective • Power supply unit defective
547   Zero cross signal malfunction
Zero cross signals are not detected within 5 seconds after the main power switch is turned on, or are not detected within 1 second after operation begins ( copyir.com )    • Power supply board defective • IOB defective • BiCU defective
620   Communication error between IOB and ADF
The IOB does not receive a response from the ADF main board for 4 seconds or more ( copyir.com )    • Poor connection between the IOB and ADF main board (DF connector) • ADF main board defective • IOB defective
691   Communication error between BiCU and fax controller
The BiCU board cannot communicate with the fax controller ( copyir.com )    • Poor connection between the BiCU board and the fax controller • BiCU board defective • Fax controller defective
692   Communication error between BiCU and printer controller
The BiCU board cannot communicate with the printer controller ( copyir.com )    • Poor connection between the BiCU board and the printer controller ( copyir.com ) • BiCU board defective • Printer controller defective
695   Fax firmware error
The fax program cannot be started ( copyir.com )    • The fax firmware download has not been completed correctly ( copyir.com ) Try again ( copyir.com )
760   ADF gate abnormal
The ADF Gate signal line between the ADF main board and the IOB is disconnected ( copyir.com )    • ADF main board defective • Input/output board defective • Poor connection (ADF Gate line) between the ADF main board and the IOB ( copyir.com )
900   Electrical total counter error
The electrical total counter does not work properly ( copyir.com )    • NVRAM defective
901   Mechanical total counter
The mechanical total counter does not work properly ( copyir.com )    • Mechanical total counter defective • IOB defective • Disconnected mechanical total counter
921   IMB memory controller error
A memory control job is not completed within a certain period ( copyir.com )    • IMB defective • BiCU defective • Poor connection between IMB and BiCU
922   IMB DRAM error
The machine detects a discrepancy in the IMB DRAM write/read data during its write/read test (done at power off/on and at recovery from low power or night/off mode) ( copyir.com )    • IMB defective • BiCU defective • Poor connection between BiCU and IMB
924   Optional DRAM error
The machine detects a discrepancy in the Optional DRAM write/read data during its write/read test (done at power off/on and at recovery from low power or night/off mode) ( copyir.com )    • Non-supported DRAM connected • Poor connection between IMB and optional DRAM • Optional DRAM defective • IMB defective • BiCU defective
925   IMB non-connected error
IMB is not connected ( copyir.com ) This SC only appears with B040 and B043 version machines ( copyir.com )    • IMB is not connected • Poor connection between BiCU and IMB • IMB defective • BiCU defective
926   Memory capacity error
The machine detects a discrepancy between the memory capacity detected during the memory check at power on and the check at recovery from low power or night/off mode ( copyir.com )    • Poor connection between optional DRAM and IMB • Optional DRAM defective • IMB defective • BiCU defective
981   NVRAM error
The machine detects a discrepancy in the NVRAM write/read data when attempting to save actual data to the NVRAM (i ( copyir.com ) e ( copyir.com ) during actual use) ( copyir.com )    • NVRAM defective • Poor connection between BiCU and NVRAM • NVRAM is not connected • BiCU defective
990   Communication error between BICU and IOB
The BiCU board cannot communicate with the IOB ( copyir.com )    • The connection between the BiCU board and the IOB is poor ( copyir.com ) • BiCU board defective • IOB defective
999   Program version error
An incorrect type of main software was downloaded ( copyir.com )    • The main software for another machine was downloaded to this machine ( copyir.com ) Switch the machine off ( copyir.com ) Connect an IC card that has the correct firmware to the machine ( copyir.com ) Switch the machine on, and download the firmware (see section 5 ( copyir.com ) 1 ( copyir.com ) 9) ( copyir.com )
695   Fax firmware error
The fax program cannot be started ( copyir.com )    • The fax firmware download has not been completed correctly ( copyir.com ) Try again ( copyir.com )
760   ADF gate abnormal
The ADF Gate signal line between the ADF main board and the IOB is disconnected ( copyir.com )    • ADF main board defective • Input/output board defective • Poor connection (ADF Gate line) between the ADF main board and the IOB ( copyir.com )
900   Electrical total counter error
The electrical total counter does not work properly ( copyir.com )    • NVRAM defective
901   Mechanical total counter
The mechanical total counter does not work properly ( copyir.com )    • Mechanical total counter defective • IOB defective • Disconnected mechanical total counter
921   IMB memory controller error
A memory control job is not completed within a certain period ( copyir.com )    • IMB defective • BiCU defective • Poor connection between IMB and BiCU
922   IMB DRAM error
The machine detects a discrepancy in the IMB DRAM write/read data during its write/read test (done at power off/on and at recovery from low power or night/off mode) ( copyir.com )    • IMB defective • BiCU defective • Poor connection between BiCU and IMB
924   Optional DRAM error
The machine detects a discrepancy in the Optional DRAM write/read data during its write/read test (done at power off/on and at recovery from low power or night/off mode) ( copyir.com )    • Non-supported DRAM connected • Poor connection between IMB and optional DRAM • Optional DRAM defective • IMB defective • BiCU defective
925   IMB non-connected error
IMB is not connected ( copyir.com ) This SC only appears with B040 and B043 version machines ( copyir.com )    • IMB is not connected • Poor connection between BiCU and IMB • IMB defective • BiCU defective
926   Memory capacity error
The machine detects a discrepancy between the memory capacity detected during the memory check at power on and the check at recovery from low power or night/off mode ( copyir.com )    • Poor connection between optional DRAM and IMB • Optional DRAM defective • IMB defective • BiCU defective
981   NVRAM error
The machine detects a discrepancy in the NVRAM write/read data when attempting to save actual data to the NVRAM (i ( copyir.com ) e ( copyir.com ) during actual use) ( copyir.com )    • NVRAM defective • Poor connection between BiCU and NVRAM • NVRAM is not connected • BiCU defective
990   Communication error between BICU and IOB
The BiCU board cannot communicate with the IOB ( copyir.com )    • The connection between the BiCU board and the IOB is poor ( copyir.com ) • BiCU board defective • IOB defective
999   Program version error
An incorrect type of main software was downloaded ( copyir.com )    • The main software for another machine was downloaded to this machine ( copyir.com ) Switch the machine off ( copyir.com ) Connect an IC card that has the correct firmware to the machine ( copyir.com ) Switch the machine on, and download the firmware (see section 5 ( copyir.com ) 1 ( copyir.com ) 9) ( copyir.com )
695   Fax firmware error
The fax program cannot be started ( copyir.com )    • The fax firmware download has not been completed correctly ( copyir.com ) Try again ( copyir.com )
760   ADF gate abnormal
The ADF Gate signal line between the ADF main board and the IOB is disconnected ( copyir.com )    • ADF main board defective • Input/output board defective • Poor connection (ADF Gate line) between the ADF main board and the IOB ( copyir.com )
900   Electrical total counter error
The electrical total counter does not work properly ( copyir.com )    • NVRAM defective
901   Mechanical total counter
The mechanical total counter does not work properly ( copyir.com )    • Mechanical total counter defective • IOB defective • Disconnected mechanical total counter
921   IMB memory controller error
A memory control job is not completed within a certain period ( copyir.com )    • IMB defective • BiCU defective • Poor connection between IMB and BiCU
922   IMB DRAM error
The machine detects a discrepancy in the IMB DRAM write/read data during its write/read test (done at power off/on and at recovery from low power or night/off mode) ( copyir.com )    • IMB defective • BiCU defective • Poor connection between BiCU and IMB
924   Optional DRAM error
The machine detects a discrepancy in the Optional DRAM write/read data during its write/read test (done at power off/on and at recovery from low power or night/off mode) ( copyir.com )    • Non-supported DRAM connected • Poor connection between IMB and optional DRAM • Optional DRAM defective • IMB defective • BiCU defective
925   IMB non-connected error
IMB is not connected ( copyir.com ) This SC only appears with B040 and B043 version machines ( copyir.com )    • IMB is not connected • Poor connection between BiCU and IMB • IMB defective • BiCU defective
926   Memory capacity error
The machine detects a discrepancy between the memory capacity detected during the memory check at power on and the check at recovery from low power or night/off mode ( copyir.com )    • Poor connection between optional DRAM and IMB • Optional DRAM defective • IMB defective • BiCU defective
981   NVRAM error
The machine detects a discrepancy in the NVRAM write/read data when attempting to save actual data to the NVRAM (i ( copyir.com ) e ( copyir.com ) during actual use) ( copyir.com )    • NVRAM defective • Poor connection between BiCU and NVRAM • NVRAM is not connected • BiCU defective
990   Communication error between BICU and IOB
The BiCU board cannot communicate with the IOB ( copyir.com )    • The connection between the BiCU board and the IOB is poor ( copyir.com ) • BiCU board defective • IOB defective
999   Program version error
An incorrect type of main software was downloaded ( copyir.com )    • The main software for another machine was downloaded to this machine ( copyir.com ) Switch the machine off ( copyir.com ) Connect an IC card that has the correct firmware to the machine ( copyir.com ) Switch the machine on, and download the firmware (see section 5 ( copyir.com ) 1 ( copyir.com ) 9) ( copyir.com )