لمینت MKP
1402-06-04
Menu
101-001 Exposure lamp error Shading at AGC
The shading data peak does not reach the specified threshold (64/255 degit) when the machine executes the shading at initialization ( copyir.com • Defective exposure lamp • Defective lamp stabilizer • Defective exposure lamp harness
101-002 Exposure lamp error Shading at scanning
The shading data peak does not reach the specified threshold (64/255 degit) when the machine executes the shading at scanning ( copyir.com • Defective exposure lamp • Defective lamp stabilizer • Defective exposure lamp harness
120 Scanner home position error 1
The scanner home position sensor does not detect the “OFF” condition during operation ( copyir.com • Defective scanner motor drive board • Defective scanner motor • Defective home position sensor • Defective harness
121 Scanner home position error 2
The scanner home position sensor does not detect the “ON” condition during operation • Defective scanner motor drive board • Defective scanner motor • Defective home position sensor • Defective harness
141 Black level detection error
The black level cannot be adjusted within the target value during the zero clamp after the AGC ( copyir.com • Defective SBU • Defective harness
142 White level detection error
The white level cannot be adjusted within the target value during the zero clamp after the AGC ( copyir.com • Defective SBU • Defective harness
144-001 SBU connection error
The SBU connection cannot be detected at power on or recovery from the energy save mode ( copyir.com • Insufficient power supply for SBU • Defective SBU • Defective harness • Defective detection port on the BCU
144-002 SBU serial communication error
The unusual register value from the SBU is detected more than three times at power on or recovery from the energy save mode ( copyir.com • Insufficient power supply for SBU • Defective SBU • Defective harness • Defective detection port on the BCU
144-003 GBSBU reset error
The GBSBU cannot be reset at power on or recovery from the energy save mode • Insufficient power supply for SBU • Defective SBU • Defective harness • Defective detection port on the BCU
144-004 Cannot finish the SBU communication ( copyir.com
The communication between BCU and SBU has not completed ( copyir.com • Insufficient power supply for SBU • Defective SBU • Defective harness • Defective detection port on the BCU
161-001 IPU error The error result of self-diagnostic by the Taurus (ASIC on the IPU) is detected ( copyir.com not completed ( copyir.com • Defective IPU • Defective BCU • Defective connection between IPU and SBU
161-002 ASIC (Taurus) memory error
The memory check error of ASIC (Taurus) is detected when a machine turns on or recovers from the energy saver mode ( copyir.com • Defective IPU (Taurus memory) • Unusual power source
165 Copy Data Security Unit error
• The copy data security board is not detected when the copy data security function is set “ON” with the initial setting ( copyir.com • A device check error occurs when the copy data security function is set “ON” with the initial setting ( copyir.com • Incorrect installation of the copy data security board • Defective copy data security board
200 Maintenance unit home position error
• The maintenance unit sensor does not get “OFF” signal after the maintenance unit motor has rotated ( copyir.com • The maintenance unit sensor does not get “ON” signal even the maintenance unit motor has rotated for certain time when it is assumed that the maintenance unit has to return to the home position ( copyir.com • Defective maintenance unit home position sensor • Defective maintenance unit drive motor
202 Tank full lever error
• The position of the tank full lever does not stay at the tank full position after ink initialization or air releasing ( copyir.com • The position of the tank full lever is not detected at ink suction ( copyir.com • Defective tank full sensor • Tank full lever bent or broken • Incorrect ink suction
210 Main scan encoder signal error
The input signal from the main scan encoder is not detected during operation of the main scan motor ( copyir.com • Defective main scan encoder • Defective main scan encoder sensor • Defective main scan drive motor
211 Main scan encoder error
The carriage unit does not stop at home position (rear side) or reverse position (front side) ( copyir.com • Defective main scan drive motor • Main scan encoder coming off • Defective main scan encoder sensor
503 Tray 2 (optional paper tray unit) feed error
• The lift sensor is not activated within 18 seconds twice consecutively after the tray lift motor starts lifting the bottom plate ( copyir.com • When the tray lowers, the tray lift sensor does not go off within 1 ( copyir.com 5 sec twice consecutively ( copyir.com • Defective or disconnected tray lift motor • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Reverse connection of harness
504 Tray 3 (optional paper tray unit) feed error
• The lift sensor is not activated within 18 seconds twice consecutively after the tray lift motor starts lifting the bottom plate ( copyir.com • When the tray lowers, the tray lift sensor does not go off within 1 ( copyir.com 5 sec twice consecutively ( copyir.com • Defective or disconnected tray lift motor • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Reverse connection of harness
506 Paper feed motor lock error (optional paper tray unit) A motor lock signal is not detected for more than 1 ( copyir.com 5 s or the lock signal is not detected for more than 1 ( copyir.com 0 s during rotation ( copyir.com • Defective paper feed motor • Too much load on the drive mechanism
520 Sub scan motor error
The sub scan motor does not reply for 100ms when a machine sends the “stop” command to the sub scan motor ( copyir.com • Defective sub scan encoder sensor • Timing belt of the sub scan encoder is come off ( copyir.com • Defective sub scan motor
570 Charge bias leak
High voltage unit sends a signal of charge bias leak ( copyir.com • Defective charge roller • Defective high voltage unit
571 Ink head temperature error
The temperature sensor at the ink head detects unusual temperature for 0 ( copyir.com 8 seconds ( copyir.com • Disconnect harness • Defective temperature sensor at the ink head
572 Belt temperature error
The temperature sensor at the belt unit detects unusual temperature for 0 ( copyir.com 8 seconds ( copyir.com • Disconnect harness • Defective temperature sensor at the ink head
573 Belt temperature and absolute humidity error
• The temperature sensor at the belt unit detects less than –15°C or more than 85°C ( copyir.com • The humidity sensor at the belt unit detects less than 0% or more than 100% ( copyir.com • Disconnect harness • Defective temperature sensor at the ink head
610 Mechanical counter error The machine detects disconnection of a mechanical counter when SP5987-1 is set to “ON” ( copyir.com • Disconnected mechanical counter
620 Communication command error between BCU and ADF
A communication error occurs after the machine detects the correct communication between BCU and ADF • Defective connection between ADF and BCU • Defective ADF • Defective IPU
630 CSS communication error
The machine tries to communicate with one of the terminals of a relevant service center ( copyir.com – An error signal returns ( copyir.com • Communication error on the public telephone network (logged only; the machine can still operate)
632 MF accounting device error 1 The machine sends a data frame ( copyir.com – No normal end signal returns ( copyir.com – This symptom happens three times ( copyir.com • Defective or broken line between machine and device
633 MF accounting device error 2 The machine is communicating with the accounting device ( copyir.com – The break signal returns ( copyir.com • Defective or broken line between machine and device
634 MF accounting device error 3
A backup RAM error is reported from the accounting device ( copyir.com • Defective accounting device controller • Defective battery in the accounting device ( copyir.com
635 MF accounting device error 4
A battery voltage error is reported from the accounting device ( copyir.com • Defective accounting device controller • Defective battery in the accounting device
636-001 SD Card Error Expanded authentication module error
There is no expanded authentication module in the machine ( copyir.com The SD card or the file of the expanded authentication module is broken ( copyir.com There is no DESS module in the machine ( copyir.com
636-002 SD Card Error Version error
The version of the expanded authentication module is not correct ( copyir.com
650 Communication error of the remote service modem (Cumin-M)
651 Incorrect dial up connection
670 Engine startup error
Just after the main power is turned on or the machine is recovering from auto off mode, the engine ready signal assertion fails ( copyir.com Just after the main power is turned on, the engine does not respond ( copyir.com • Poor connection between the BCU and controller board • Defective BCU • Defective controller board
672 Controller-to-operation panel communication error at startup
After powering on the machine, communication between the controller and operation panel does not begin, or the communication is interrupted after a normal startup ( copyir.com • Controller stalled • Controller board installed incorrectly • Defective controller board • Operation panel connector loose or defective • Poor connection of DIMM and optional boards on the controller board
685 SBU/IPU communication error
While data is sent between the scanner and BCU board, a communication error has occurred ( copyir.com • Defective scanner unit cable • Defective SBU board • Defective BCU board
687 Memory address command error
The BCU does not receive a memory address command from the controller 120 seconds after paper is in the position for registration ( copyir.com • Loose connection • Defective controller • Defective BCU
818 Watchdog error
While the system program is running, no other programs can run (due to a bus hold or endless loop) ( copyir.com • Defective controller board
819 Kernel stop
820 Self-Diagnostic Error: CPU
821 Self-Diagnostic Error: ASIC
822 Self-Diagnostic Error: HDD
823 Self-diagnostic Error: NIB
824 Self-diagnostic Error: NVRAM
The controller cannot recognize the standard NVRAM installed or detects that the NVRAM is defective • NVRAM damaged or abnormal • Backup battery has discharged • NVRAM socket damaged
826 Self-diagnostic Error: RTC/Optional NVRAM
827 Self-diagnostic Error: RAM
828 Self-diagnostic Error: ROM
829 Self-diagnostic Error: Optional RAM
851 IEEE1394 I/F abnormal
The IEEE1394 interface cannot be used, due to a driver error ( copyir.com • IEEE1394 interface board defective • Defective controller board
853 Wireless card startup error
The machine starts up ( copyir.com – The IEEE802 11b card connection board is recognized – The wireless LAN card or bluetooth card is not recognized ( copyir.com • Loose connection between the card and the connection board
854 Wireless card access error
The machine has been reading the data from the card ( copyir.com – The machine loses access to the card; the wireless LAN card or bluetooth card connection board is still recognized ( copyir.com • Loose connection between the card and the connection board
855 Wireless card error
Some illegal data is found in the card ( copyir.com • Defective card
856 Wireless card connection board error
An error is detected in the wireless LAN card or bluetooth card connection board ( copyir.com • Defective card connection board
857 USB I/F Error USB interface error is detected ( copyir.com • Defective controller
860 HDD startup error at main power on
HDD is connected but a driver error is detected ( copyir.com The driver does not respond with the status of the HDD within 30 s ( copyir.com • No formatted HDD • Label name input during formatting is corrupted ( copyir.com
861 HDD reboot error
The HDD does not become ready within 30 seconds after the power is supplied to the HDD ( copyir.com • Loose connection • Defective cables • Defective HDD • Defective controller
863 HDD read error
The data stored in the HDD cannot be read correctly ( copyir.com • Bad sector detected during operation of the HDD • Defective HDD • Defective controller
864 HD data CRC error
While reading data from the HDD or storing data in the HDD, data transmission fails ( copyir.com • Defective HDD
865 HD access error
An error other than SC863 and SC864 is detected while operating the HDD ( copyir.com • Defective HDD
866 SD card authentication error
A digital license error of an SD card application is detected ( copyir.com • SD card data has corrupted ( copyir.com
867 SD card error An application SD card is removed from the boot slot while an application is activated ( copyir.com • An application SD card is ejected ( copyir.com
868 SD card access error
(-13 to -3: File system error, other number: Device error) An error report is sent from the SD card reader ( copyir.com • SD card not inserted correctly • SD card defective • Controller board defective
870 Address book data error The address book in the hard disk is accessed ( copyir.com – An error is detected in the address book data; address book data is not read; or data is not written into the address book ( copyir.com ( copyir.com • Data corruption • Defective hard disk • Defective controller software
872 HDD received mail data error
An error is detected in the received mail data partition of the HDD at machine initialization ( copyir.com • Defective HDD • Power failure during an access to the HDD
873 HDD sent mail data error
An error is detected in the sent mail data partition of the HDD at machine initialization ( copyir.com • Defective HDD • Power failure during an access to the HDD
874 Delete All error 1: HDD
An error is detected while the all data of the HDD or NVRAM are formatted physically by the Data Overwrite Security Unit (B735) ( copyir.com • Not installed Data Overwrite Security Unit (SD card) • Defective HDD
875 Delete All error 2: Data area
An error is detected while the all data of the HDD or NVRAM are formatted logically by the Data Overwrite Security Unit (B735) ( copyir.com • The logical format for HDD fails ( copyir.com
876 Log Data Error
877 HDD Data Overwrite Security SD card error
The all delete cannot be executed even though the Data Overwrite Security Unit (B735) is installed and activated ( copyir.com • Defective SD card (B735) • Not installed SD card (B735)
880 File Format Converter (MLB) error
A request to get access to the MLB was not answered within the specified time ( copyir.com • MLB defective
900 Electronic total counter error
The value of the total counter is out of the normal range ( copyir.com • Defective NVRAM
920 Printer error
An application error that stops the machine operation is detected ( copyir.com • Defective software
921 Printer font error
A necessary font is not found in the SD card when the printer application starts ( copyir.com • A necessary font is not found in the SD card ( copyir.com • The SD card data is corrupted ( copyir.com
925 Net file error
The management file for net files is corrupted; net files are not normally read ( copyir.com Netfiles: Jobs to be printed from the document server using a PC and the DeskTop- Binder software • Defective hard disk • Data corruption • Defective software
990 Software performance error
The software attempted to perform an unexpected operation ( copyir.com NOTE: When this error occurs, the file name, address, and data will be stored in NVRAM ( copyir.com This information can be checked by using SP7-403 ( copyir.com See the data and the situation in which this SC occurs ( copyir.com Then report the data and conditions to your technical control center • Software defective • Internal parameter incorrect • Insufficient working memory
991 Software continuity error The software attempted to perform an unexpected operation ( copyir.com However, unlike SC990, the process can keep on running ( copyir.com • Logged only; the machine can continue to operate
992 Undefined error An error not controlled by the system occurred (the error does not come under any other SC code) ( copyir.com • Defective software program
997 Application function selection error
The application selected by a key press on the operation panel does not start or ends abnormally ( copyir.com • Software for that application is defective • An option required by the application (RAM, DIMM, board) is not installed ( copyir.com • Too complicated nest of the fax group address
998 Application start error
After switching the machine on, the application does not start within 60 s ( copyir.com (No applications start or end normally ( copyir.com ) • Software for that application is defective • An option required by the application (RAM, DIMM, board) is not installed ( copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.