Your browser does not support JavaScript! > ریسو گراف fr3950

   کانال تلگرام کپی ایران

(0) محصول
سه شنبه, 24 فروردين 1395 17:05

ریسو گراف fr3950

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

T1    Main Motor Lock
• In 3 seconds from turning ON of the Main motor, the A detection sensor light path is still held blocked     copyir.com
• In 8 seconds from turning ON of the Main motor, the A detection sensor is not blocked     copyir.com
T10    Malfunction Image Processing PCB
• When the scanning contrast adjustment signal is not output from the image processing PCB     copyir.com
T11    Pressure Control Motor Lock
• In 100ms from turning ON of the Pressure control motor, the Encoder sensor cannot detect a pulse     copyir.com
• In 5 seconds from turning ON of the Pressure control motor, the Pressure centering sensor is not turned ON/OFF     copyir.com
T12    • Malfunction of Trimming PCB
• When the TOP signal is not output from the Trimming PCB 2
T13    Cutter Motor Lock
• After master cutting retrial with the drum held in C-2 position, when the Master positioning sensor is in light-receiving state     copyir.com (Master cutting has failed in the 2nd time     copyir.com)
T14    Clamp Error (2)
• If the actuator of the Clamp safety switch is not depressed when the Clamp solenoid is not in operation     copyir.com
T15    Flat Bed Read Pulse Motor Lock
• If the Image scanner home position sensor does not detect the Image scanner within 18898 pulses after the Flat bed read pulse motor is activated     copyir.com
• If the Image scanner ADF Shading sensor does not detect the Image scanner within 15748 pulses after the Flat bed read pulse motor is activated     copyir.com • If the scanner home position sensor does not detect the Image scanner within 14,551 pulses(462 mm worth) after the Flat bed read pulse motor is activated during prescanning     copyir.com
• If the Image scanner is not release from the Image scanner home position sensor within 314 pulses after the Flat bed read pulse motor is activated     copyir.com
• If the Image scanner is not released from the Image scanner ADF Shading sensor within 314 pulses after the Flat bed read pulse motor is activated     copyir.com
T16    Position C Sensor Malfunction
• If the Position C sensor status has not been changed from ON to OFF (or OFF to ON) within 8 seconds from the start of the Main Motor     copyir.com
T17    Replace Battery
• When the battery voltage is less than 2     copyir.com4 V at power-on, all reset, or end of operation     copyir.com
T18    Sorter Error
• If an error signal is received from the sorter     copyir.com
T19    Thermal Pressure Motor Lock
• If the TPH Pressure switch has not been depressed within 4 seconds after the TPH Pressure motor was activated to lower the TPH     copyir.com
• If the TPH Pressure switch has not been released within 4 seconds after the TPH Pressure motor was activated to raise the TPH     copyir.com
T2    Elevator Motor Lock
• In 15 seconds from turning ON of the Elevator motor in upward direction, the Elevator upper limit sensor is not pushed     copyir.com
• In 15 seconds from turning ON of the Elevator motor in downward direction, the light path of the Elevator lower limit sensor is not blocked     copyir.com
• In 3 seconds from turning ON of the Elevator motor in upward direction, the Elevator lower sensor is held blocked     copyir.com
• In 3 seconds from turning ON of the Elevator motor in downward direction, the Elevator upper limit sensor is held pressed down     copyir.com
T20    Wing Motor Lock
• If neither of the Jump wing sw1 or sw2 has been depressed within 5 seconds after the Wing motor was activated     copyir.com
• If neither of the Jump wing sw1 or sw2 has been released within 5 seconds after the Wing motor was activated     copyir.com
T3    Clamp Error (1)
• In 4 seconds from turning ON of the Clamp solenoid in clamp retrial, the Clamp safety switch is held still pressed down     copyir.com
• In 4 seconds from turning OFF of the Clamp solenoid, the Clamp safety SW has not been pressed     copyir.com
• In 8 seconds from turning ON of the Clamp motor in opening direction in clamp retrial, the 180° Angular sensor has not detected magnet     copyir.com
• In 8 seconds from turning ON of the Clamp motor in closing direction in clamp retrial, the 0° Angular sensor has not detected magnet     copyir.com
In any of the above cases, master making is performed to the end     copyir.com
T30    P     copyir.com -F     copyir.com Tray Slide Pulse Motor
• When the Paper feed tray position sensor is not turned on/ off within 165 pulses(approx     copyir.com 3 second) after the P     copyir.com -F     copyir.com tray slide pulse motor is turned on     copyir.com
T4    Overflow
• When ink is in contact with the Overflow sensor     copyir.com The Drum set switch need be pushed     copyir.com
T5    Print Positioning Motor Lock
• In 12 seconds from turning ON of the Print positioning motor, the Vertical centering sensor is not turned ON/OFF     copyir.com
T50    Connect “Copy/Master” Counter
• When the copy counter or the master counter has not been connected     copyir.com
T6    Pressure Detection Sensor Malfunction
• In 8 seconds from turning ON of the main motor, the Pressure detection sensor is not turned ON/OFF     copyir.com
T68    SF3000 Power Supply Malfunction
• When no power is supplied to the SF3000     copyir.com
T7    Communication error between FR and Digitizer
• On occurrence of an error in communication between the System PCB and Digitizer III     copyir.com
T78    Machine Model Selection Error
• When there is no machine type which corresponds to the code having been set in System PCB     copyir.com
T79    Destination Spec     copyir.com Code Error
• When the code set (DIP switch) does not match the model set with the Hex     copyir.com switch     copyir.com
T8    Communication error between System PCB and Panel PCB
• On occurrence of an error in communication between the System PCB and the Panel PCB     copyir.com
T9    Communication error between FR and the Sorters
• On occurrence of an error in communication between the System PCB and the Sorter (TM)

خواندن 947 دفعه
محتوای بیشتر در این بخش: « ریسو گراف fr3910 ریسو گراف gr seies »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب