Your browser does not support JavaScript! > ریسو گراف ks600

   کانال تلگرام کپی ایران

(0) محصول
شنبه, 28 فروردين 1395 11:08

ریسو گراف ks600

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

C1    Close Separation fan unit
• If the actuator of the Separation base unit safety switch is not depressed     copyir     copyir     copyir.comcomcom
C2    Close Master Making Unit
• If the actuator of the Master making unit safety switch is not depressed     copyir     copyir     copyir.comcomcom
C3    Close Master Removal Unit
• If the actuator of the Master removal unit safety switch is not depressed     copyir     copyir     copyir.comcomcom
C4    Set master disposal box     copyir     copyir     copyir.comcomcom
• If the master disposal box set sensor does not detect     copyir     copyir     copyir.comcomcom
C5    Set Ink bottle in Place
• If the Ink bottle set sensor does not detect the Ink bottle     copyir     copyir     copyir.comcomcom
C6    Replace Master Roll
• If the black tape attached at the end of the Master roll has been detected by the Master end sensor during master making or confidential operation     copyir     copyir     copyir.comcomcom
C7    Empty Disposal Box
• If the Master removal 5 times     copyir     copyir     copyir.comcomcom
C8    Replace Ink bottle
• If the Ink sensor does not detect ink in the Squeegee unit within 20 seconds after the Inking motor was activated     copyir     copyir     copyir.comcomcom
• If the Ink sensor does not detect ink in the Squeegee unit within 40 seconds after the Inking motor was activated when the Ink bottle is installed just after replacing empty ink bottle     copyir     copyir     copyir.comcomcom
E1    Main Motor Lock
• If excessive current is detected 0     copyir     copyir     copyir.comcomcom3 seconds consecutively after the Main motor is activated     copyir     copyir     copyir.comcomcom
• If no Encoder sensor output after Main motor is activated     copyir     copyir     copyir.comcomcom
E12    Master removal motor lock
• Excessive current to the motor is detected three time consecutively during the current check made every 100 ms     copyir     copyir     copyir.comcomcom
E13    Cutter motor Lock
• If the Cutter home position switch is not turned OFF within 500 ms after the Cutter motor is activated     copyir     copyir     copyir.comcomcom
• If the Cutter end position switch is not pressed within 2000 ms after the Cutter motor is activated     copyir     copyir     copyir.comcomcom
E16    Inking Motor Lock
• If excessive current is detected 2     copyir     copyir     copyir.comcomcom5 seconds consecutively after the Inking motor is activated     copyir     copyir     copyir.comcomcom
E19    TPH pressure error [During TPH Up Positioning]
• If the light path of the TPH pressure sensor is not opened within 10 seconds after the Write pulse motor is activated     copyir     copyir     copyir.comcomcom [During TPH Down Positioning]
• If the light path of the TPH pressure sensor is not blocked within 10 seconds after the Write pulse motor is activated     copyir     copyir     copyir.comcomcom
E3    Clamp Motor Lock [During Clamp Motor Initial Positioning]
• If the light path of the Clamp senors both C and L are not opened within 10 seconds after after the Clamp motor is activated     copyir     copyir     copyir.comcomcom [During Master Release from the Clamp Plate]
• If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated     copyir     copyir     copyir.comcomcom
• If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated     copyir     copyir     copyir.comcomcom [When the Clamp Plate opens during Master Clamping]
• If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated     copyir     copyir     copyir.comcomcom
• If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated     copyir     copyir     copyir.comcomcom [When the Clamp Plate closes during Master Clamping]
• If the light path of the Clamp sensor L is not opened within 10 seconds after the Clamp motor is activated     copyir     copyir     copyir.comcomcom
E4    Ink Overflow
• If the Overflow sensor detects excessive ink in the Squeegee unit     copyir     copyir     copyir.comcomcom
E6    Position     copyir     copyir     copyir.comcomcomA Sensor Malfunction
• If Position     copyir     copyir     copyir.comcomcomA sensor cannot be detected (or keeps detecting     copyir     copyir     copyir.comcomcom even though the Main motor encoder sensor signal is making the output after the Main motor is activated     copyir     copyir     copyir.comcomcom
J1    No Master on the Drum
• If the Master sensor does not find master on the Drum when the Drum is at 134° during the printing movement     copyir     copyir     copyir.comcomcom
J10    Removed Master Jammed at the Master removal area
• If the Master removal sensor is detecting the removed master (light path blocked     copyir     copyir     copyir.comcomcom even though the Drum has returned to the position     copyir     copyir     copyir.comcomcomA after the master removal process     copyir     copyir     copyir.comcomcom
J2    Paper Jam in the Second Paper Feed Area
• If the Paper receiving sensor does not find paper when the Drum is at Position     copyir     copyir     copyir.comcomcom334° and 104° the printing operation     copyir     copyir     copyir.comcomcom
J3    Paper Jam in the Paper Receiving Area
• If the status of the Paper receiving sensor does not change from detecting paper to not detecting from Drum angle 357° to 280° the printing operation     copyir     copyir     copyir.comcomcom
J4    Master Loading Error
• If the Master sensor does not detect the master (light not reflected     copyir     copyir     copyir.comcomcom within 5 seconds     copyir     copyir     copyir.comcomcom
J5    Master Loading Error (onto the Drum     copyir     copyir     copyir.comcomcom
• If the Master sensor does not detect the master (light not reflected     copyir     copyir     copyir.comcomcom during the master loading when the Drum is at 134° from the position     copyir     copyir     copyir.comcomcomA     copyir     copyir     copyir.comcomcom
J6    Master Cut Malfunction
• If the Master positioning sensor is still detecting the master (light reflected back     copyir     copyir     copyir.comcomcom when the Drum is at position     copyir     copyir     copyir.comcomcomA after the cutting     copyir     copyir     copyir.comcomcom
J7    Original Jam at Entrance
• During the Original scanning, if the Original IN sensor does not detecting within 5 second after the Read pulse motor activates     copyir     copyir     copyir.comcomcom
J8    Original Jam
• During the Original set movement, if the Original IN sensor still detecting Original (sensor light reflected     copyir     copyir     copyir.comcomcom the master making movement     copyir     copyir     copyir.comcomcom
J9    Master Removal Error
• In case the Master removal sensor does not detect the removed master (light path opened     copyir     copyir     copyir.comcomcom at Drum 134° from the Position      copyir     copyir     copyir.comcomcomA during the master removal even though a master was detected on the Drum before the master removal operation     copyir     copyir     copyir.comcomcom
C1    Close Separation fan unit
• If the actuator of the Separation base unit safety switch is not depressed     copyir.com
C2    Close Master Making Unit
• If the actuator of the Master making unit safety switch is not depressed     copyir.com
C3    Close Master Removal Unit
• If the actuator of the Master removal unit safety switch is not depressed     copyir.com
C4    Set master disposal box     copyir.com
• If the master disposal box set sensor does not detect     copyir.com
C5    Set Ink bottle in Place
• If the Ink bottle set sensor does not detect the Ink bottle     copyir.com
C6    Replace Master Roll
• If the black tape attached at the end of the Master roll has been detected by the Master end sensor during master making or confidential operation     copyir.com
C7    Empty Disposal Box
• If the Master removal 5 times     copyir.com
C8    Replace Ink bottle
• If the Ink sensor does not detect ink in the Squeegee unit within 20 seconds after the Inking motor was activated     copyir.com
• If the Ink sensor does not detect ink in the Squeegee unit within 40 seconds after the Inking motor was activated when the Ink bottle is installed just after replacing empty ink bottle     copyir.com
E1    Main Motor Lock
• If excessive current is detected 0     copyir.com3 seconds consecutively after the Main motor is activated     copyir.com
• If no Encoder sensor output after Main motor is activated     copyir.com
E12    Master removal motor lock
• Excessive current to the motor is detected three time consecutively during the current check made every 100 ms     copyir.com
E13    Cutter motor Lock
• If the Cutter home position switch is not turned OFF within 500 ms after the Cutter motor is activated     copyir.com
• If the Cutter end position switch is not pressed within 2000 ms after the Cutter motor is activated     copyir.com
E16    Inking Motor Lock
• If excessive current is detected 2     copyir.com5 seconds consecutively after the Inking motor is activated     copyir.com
E19    TPH pressure error [During TPH Up Positioning]
• If the light path of the TPH pressure sensor is not opened within 10 seconds after the Write pulse motor is activated     copyir.com [During TPH Down Positioning]
• If the light path of the TPH pressure sensor is not blocked within 10 seconds after the Write pulse motor is activated     copyir.com
E3    Clamp Motor Lock [During Clamp Motor Initial Positioning]
• If the light path of the Clamp senors both C and L are not opened within 10 seconds after after the Clamp motor is activated     copyir.com [During Master Release from the Clamp Plate]
• If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated     copyir.com
• If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated     copyir.com [When the Clamp Plate opens during Master Clamping]
• If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated     copyir.com
• If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated     copyir.com [When the Clamp Plate closes during Master Clamping]
• If the light path of the Clamp sensor L is not opened within 10 seconds after the Clamp motor is activated     copyir.com
E4    Ink Overflow
• If the Overflow sensor detects excessive ink in the Squeegee unit     copyir.com
E6    Position-A Sensor Malfunction
• If Position-A sensor cannot be detected (or keeps detecting) even though the Main motor encoder sensor signal is making the output after the Main motor is activated     copyir.com
J1    No Master on the Drum
• If the Master sensor does not find master on the Drum when the Drum is at 134° during the printing movement     copyir.com
J10    Removed Master Jammed at the Master removal area
• If the Master removal sensor is detecting the removed master (light path blocked) even though the Drum has returned to the position-A after the master removal process     copyir.com
J2    Paper Jam in the Second Paper Feed Area
• If the Paper receiving sensor does not find paper when the Drum is at Position-334° and 104° the printing operation     copyir.com
J3    Paper Jam in the Paper Receiving Area
• If the status of the Paper receiving sensor does not change from detecting paper to not detecting from Drum angle 357° to 280° the printing operation     copyir.com
J4    Master Loading Error
• If the Master sensor does not detect the master (light not reflected) within 5 seconds     copyir.com
J5    Master Loading Error (onto the Drum)
• If the Master sensor does not detect the master (light not reflected) during the master loading when the Drum is at 134° from the position-A     copyir.com
J6    Master Cut Malfunction
• If the Master positioning sensor is still detecting the master (light reflected back) when the Drum is at position-A after the cutting     copyir.com
J7    Original Jam at Entrance
• During the Original scanning, if the Original IN sensor does not detecting within 5 second after the Read pulse motor activates     copyir.com
J8    Original Jam
• During the Original set movement, if the Original IN sensor still detecting Original (sensor light reflected) the master making movement     copyir.com
J9    Master Removal Error
• In case the Master removal sensor does not detect the removed master (light path opened) at Drum 134° from the Position -A during the master removal even though a master was detected on the Drum before the master removal operation     copyir.com

خواندن 886 دفعه
محتوای بیشتر در این بخش: « ریسو گراف ks500 ریسو گراف ks800 »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب