A01     copyir.com201    Master     copyir.compositioning sensor does not go ON even after the write pulse motor is activated during the master     copyir.compositioning, master     copyir.comcut, ormaster     copyir.comloading operation.
A01     copyir.com202    Master     copyir.compositioning sensor does not go OFF even when the write pulse motor is reversed during the master     copyir.compositioning or at start ofmaster     copyir.commaking operation.
A01     copyir.com206    Timeout error during master     copyir.commaking operation
A01     copyir.com211    Master     copyir.compositioning sensor is ON during standby.
A01     copyir.com214    Master     copyir.compositioning sensor is ON at the start of master making.
A01     copyir.com215    Faulty gate     copyir.comarray control for the write pulse motor (motor does not stop within set time)
A02     copyir.com509    Master     copyir.comloading sensor was OFF when the master was checked at a specified drum angle during the master     copyir.comloading oper201ation.
A04     copyir.com303    Master     copyir.comdisposal jam sensor was OFF at both 120 and 180 degrees drum angle.
A04     copyir.com314    Master     copyir.comdisposal error (recovery error).
A05     copyir.com304    Master     copyir.comdisposal jam sensor was ON at the completion of the master     copyir.comdisposal operation.
A05     copyir.com312    The master     copyir.comdisposal jam sensor was ON at the start of master     copyir.commaking operation.
A05     copyir.com315    The master     copyir.comdisposal jam sensor was ON when the master disposal box was set in the machine.
A06     copyir.com403    Paper     copyir.comfeed     copyir.comtray upper or lower safety switch is OFF.
A07     copyir.com409    Paper     copyir.comejection sensor was OFF when the paper should have arrived, and the paper sensor was ON when the machine stopped (Papermisfeed).
A07     copyir.com412    Paper sensor was OFF three times in succession when a paper misfeed was detected (paper misfeed).
A07     copyir.com413    Paper sensor was ON when the paper should have left the paper sensor (long     copyir.comlength paper mode error).
A07     copyir.com418    The paper sensor was ON at the start of machine operation when the START button was pressed.
A07     copyir.com429    Paper feed error (recovery error).
A07     copyir.com432    Paper sensor was ON when the machine went into paper feed retry movement after a paper misfeed.
A08     copyir.com410    Paper     copyir.comejection sensor was OFF when paper should have arrived, and the paper sensor was OFF when the machine stopped (paper jamon the print drum).
A08     copyir.com421    Paper sensor was ON when the paper should have left the paper sensor during feeding of long paper in long     copyir.comlength paper mode (paperlonger than 555 mm).
A08     copyir.com430    Paper jam on print drum (recovery error).
A09     copyir.com411    Paper     copyir.comejection sensor was ON when the paper should have left the paper     copyir.comejection sensor.
A09     copyir.com417    Paper     copyir.comejection sensor was ON at the start of machine operation when the START button was pressed.
A09     copyir.com431    Paper     copyir.comejection error (recovery error).
A10     copyir.com102    Original     copyir.comregistration     copyir.comsensor remaining jam
A10     copyir.com103    Original     copyir.comIN     copyir.comsensor remaining jam
A10     copyir.com105    Original     copyir.comregistration     copyir.comsensor non     copyir.comarrival jam
A10     copyir.com106    Original     copyir.comIN     copyir.comsensor non     copyir.comarrival jam
A10     copyir.com107    Original     copyir.comOUT     copyir.comsensor non     copyir.comarrival jam
A10     copyir.com109    An original feed error occurred, due to opening the AF.
A10     copyir.com162    No original in AF during AF master making.
A16     copyir.com525    Waiting for the master to be removed.
A17     copyir.com209    Cutter home     copyir.composition switch is OFF at the start of master     copyir.commaking or master     copyir.comset operation.
A34     copyir.com218    Request to resetting the master.
B01     copyir.com730    Keycard counter: No card
B22     copyir.com721    With the “Tape separation” function set ON, no power is supplied to the job separator when start key is pressed.
B22     copyir.com727    After cluster     copyir.comA signal turned ON, BUSY     copyir.comsignal stayed "L" more than 7 seconds (power to job separator was turned OFF while the tape isbeing ejected.
B23     copyir.com722    With the “Tape separation” function set ON, no tape detected in the job separator when the start key is pressed.
B23     copyir.com723    No tape remains in job separator upon completion of the tape     copyir.comejection operation.
B24     copyir.com724    Tape jam detected when the start key is pressed with the “Tape separation” function set to ON.
B24     copyir.com725    Job separator tape     copyir.comjam detection signal is “H” within 1,200 milliseconds after the cluster     copyir.comA signal turns ON (tape misfeed).
B24     copyir.com726    Job separator tape     copyir.comjam detection signal is “L” when the BUSY signal changes from “L” to “H” (or after 7 sec. at “L”) after the cluster     copyir.comAsignal goes ON (tape misfeed).
B31     copyir.com916    Network cable is not connected when the machine is powered ON.
B32     copyir.com917    Communication error on the network.
B32     copyir.com920    Error detected by Network Interface Card (NIC)      copyir.com NAK (negative acknowledgement was received).
B33     copyir.com931    DHCP server is not found with DHCP ON.
B34     copyir.com919    Error detected on the locally connected printer.
C01     copyir.com512    The ink sensor did not go ON even when inking was performed for the preset period.
C01     copyir.com563    Ink remaining amount is zero.
C01     copyir.com574    Inkless error was detected 5 times consecutively on one same ink bottle.
C02     copyir.com200    The master end was detected twice in succession at 10     copyir.commilliseconds intervals during master transport.
C02     copyir.com240    Master remaining amount is zero
C03     copyir.com308    Compression detection position was reached before the master     copyir.comcompression     copyir.commotor encoder     copyir.comsensor count reached the specified level,after the master compression motor turned ON in the compression direction.
C03     copyir.com313    Master removal box full detected by the master removal count.
C04     copyir.com402    Paper detection sensor is OFF (no paper on the feed tray).
D01     copyir.com526    Print drum is not set in the machine (drum connection signal, drum safety switch, and drum     copyir.comlock sensor is OFF.
D01     copyir.com527    Print drum connection signal is OFF when the print drum was inserted in the machine.
D01     copyir.com528    Print drum safety switch is OFF when the print drum was inserted in the machine.
D01     copyir.com529    Print drum lock sensor is OFF when the print drum was inserted in the machine (time     copyir.comout: 5 seconds).
D01     copyir.com530    Print drum connection signal does not go OFF within 5 seconds after the print drum safety switch went OFF when the print drum waspulled out.
D02     copyir.com532    Incorrect print drum is used.
D03     copyir.com533    Ink cartridge set sensor is OFF.
D04     copyir.com534    Incorrect ink cartridge is used.
D04     copyir.com560    Ink TAG is not detected on ink bottle.
D04     copyir.com561    Ink cartridge communication error (communication with the ink cartridge was interfered by noise).
D04     copyir.com562    Wrong ink cartridge information.
D04     copyir.com564    Detected a mismatch in ink cartridge information
D05     copyir.com210    Master detection sensor is OFF (not detecting master).
D07     copyir.com310    Disposal     copyir.combox safety switch is OFF.
D08     copyir.com224    Master making unit is not set (both the safety switch and lock sensor are OFF).
D08     copyir.com226    Master making unit safety switch is still OFF when the master making unit is set in position.
D08     copyir.com227    Master making unit lock sensor is still OFF when the master making unit is set in position (timeout: 5 seconds).
D08     copyir.com228    Master making unit lock sensor is still ON even after the master making unit safety switch went OFF, when the master making unit waspulled out of the machine.
D09     copyir.com212    Master     copyir.commaking     copyir.comunit set sensor is OFF (sensor light path is free).
D11     copyir.com535    Front cover set switch is OFF.
D13     copyir.com9    The rear cover is opened (serviceman safety switch is OFF).
D17     copyir.com236    Incorrect master roll.
D17     copyir.com237    Master roll undetected.
D17     copyir.com238    Master roll communication error.
D17     copyir.com239    Wrong master roll detected.
D17     copyir.com241    Detected a mismatch in master roll information.
D18     copyir.com522    Print drum ready for release (solenoid is ON).
D19     copyir.com223    Master making unit ready for release (solenoid is ON).
D22     copyir.com540    Error in access to the Drum PCB (unable to read from or write on the Drum PCB).
D22     copyir.com542    Abnormal data on Drum PCB.
E01     copyir.com10    Battery voltage was less than 2.5 V when the power was switched ON (weak battery: time to replace battery).
E02     copyir.com11    Master counter reached the value set for the maintenance call (value set by test mode). [The message appears when either the power isturned ON, the unit is reset, or when the machine operation ended.]
E02     copyir.com12    Copy counter reached the value set for the maintenance call (value by set test mode). [The message appears when either the power isturned ON, the unit is reset, or when the machine operation ended.]
E02     copyir.com22    Maintenance counter inside the print drum reached the value set for the maintenance call (value set by test mode). [The messageappears when either the power is turned ON, the unit is reset, or when the machine operation ended.]
F01     copyir.com15    There is no master on the print drum at the start of printing.
F02     copyir.com18    Paper size does not match with the image size on the print drum at the start of printing.
F03     copyir.com16    Multi     copyir.comup was selected using custom size paper.
F05     copyir.com19    In master making, the print quantity selected is less than the minimum print quantity.
F10     copyir.com21    Paper size does not match with the size of image on the print drum when test print is selected and activated.
F21     copyir.com32    Next original is not in placed on AF for multi     copyir.comup operation.
F22     copyir.com33    Next original is not placed on flatbed for multi     copyir.comup operation.
F37     copyir.com50    Original was set on the AF with book mode selected, when master making is activated.
F50     copyir.com910    Auto     copyir.comprinter     copyir.comselection is disabled due to error on linked printer.
F54     copyir.com923    Auto     copyir.comprinter     copyir.comselection is disabled due to no paper in the linked printer.
F55     copyir.com924    Auto     copyir.comprinter     copyir.comselection is disabled while receiving print data from PC.
F58     copyir.com927    Cannot print from linked printer (Initializing NET     copyir.comC).
H1     copyir.com566    Requesting ink color information input (Ink     copyir.comTAG related).
H2     copyir.com567    Requesting print density information input (Ink     copyir.comTAG related).
H3     copyir.com568    Requesting test printing print density information input (Ink     copyir.comTAG related).
H4     copyir.com242    Requesting master     copyir.commaking density information input (Master     copyir.comTAG related).
H5     copyir.com243    Requesting Print density information input (Master     copyir.comTAG related).
H6     copyir.com244    Requesting test printing print density information input (Master     copyir.comTAG related).
P01     copyir.com520    Main encoder sensor does not go ON/OFF within 10 milliseconds after the main motor activates.
P01     copyir.com521    B     copyir.compositioning sensor status does not change even after 3,033 pulses after the main motor activates.
P01     copyir.com524    Clamp unit is not at the home position while the print drum is in operation (except during master disposal).
P01     copyir.com537    Print drum failed to stop at position B. (over     copyir.comrun)
P01     copyir.com538    Print drum is not locked during operation. (Print     copyir.comdrum lock position sensor: OFF)
P02     copyir.com400    Both the upper and lower limit sensors were ON at the same time.
P02     copyir.com401    Overload current was detected in the elevator motor.
P02     copyir.com404    The lower     copyir.comlimit sensor does not go OFF within 2 seconds after the elevator motor operates in the raising direction from the lower     copyir.comlimitposition.
P02     copyir.com405    The upper     copyir.comlimit sensor does not go ON within 12 seconds after the elevator motor operates in the raising direction.
P02     copyir.com406    The upper     copyir.comlimit sensor does not go OFF within 2 seconds after the elevator motor operates in the lower direction from the upper     copyir.comlimitposition.
P02     copyir.com407    The lower     copyir.comlimit sensor does not go ON within 12 seconds after the elevator motor operates in the lowering direction.
P02     copyir.com408    The upper     copyir.comlimit sensor is OFF continuously for over 2 seconds during operation of the elevator servo action to raise the feed tray.
P03     copyir.com500    Clamp sensor A is OFF after the completion of the clamp unit initialization or home positioning movement.
P03     copyir.com501    Clamp sensor B does not change within 1 second from the time the clamp motor operates in the correct direction.
P03     copyir.com502    Clamp sensor B does not change within 1 second from the time the clamp motor operates in the reverse direction.
P03     copyir.com503    Clamp sensor A does not go ON within 3 seconds when the clamp unit makes initialization movement.
P03     copyir.com504    At the start of Clamp plate open/close action, the the detection sequence of clamp     copyir.comsensors A & B is abnormal.
P03     copyir.com505    At the start of print drum Positon     copyir.comA compensation movement, the detection sequence of clamp     copyir.comsensors A & B is abnormal.
P03     copyir.com506    At the start of Clamp unit Home     copyir.compositioning movement, the detection sequence of clamp     copyir.comsensors A & B is abnormal.
P03     copyir.com507    Clamp sensor A is ON after the clamp release action is completed.
P03     copyir.com508    Clamp sensor A is ON after the A     copyir.composition compensating movement is completed.
P03     copyir.com545    Clamp unit is not in the home position while the print drum is in movement (cause due to the clamp motor).
P04     copyir.com513    The overflow sensor was ON for a set number of times in succession during the 10     copyir.commillisecond     copyir.cominterval overflow     copyir.comsensor check.
P05     copyir.com603    The vertical     copyir.comcentering sensor does not switch ON even when the vertical     copyir.compositioning pulse motor activated in the image     copyir.comdown direction for5 seconds during vertical home positioning movement.
P05     copyir.com604    The vertical     copyir.comcentering sensor does not switch OFF even when the vertical     copyir.compositioning pulse motor activated in the image     copyir.comup direction for 5seconds during vertical home positioning movement.
P05     copyir.com605    Even though the vertical positioning motor stopped according to the vertical centering sensor detection, the stopping position does notcorrespond with the programmed position. (GA control error).
P05     copyir.com612    The one     copyir.comstep     copyir.compositioning key was pressed with vertical     copyir.comprint     copyir.composition information undefined.
P08     copyir.com951    Print job executed was not in correct RisoRinc format.
P11     copyir.com600    Print pressure HP sensor does not switch ON within 3.9 seconds after the print pressure pulse motor activated towards higher pressureduring home positioning operation.
P11     copyir.com601    Print pressure HP sensor does not switch OFF within 4.6 seconds after the print pressure pulse motor activated towards lower pressureduring home positioning operation.
P11     copyir.com602    Even though the print pressure control pulse motor stopped according to the print pressure HP sensor detection, the stopping positiondoes not correspond with the programmed position. (GA control error).
P12     copyir.com300    Overload current was detected in the master removal motor.
P12     copyir.com301    Master compression motor lock when moving compression plate up.
P12     copyir.com305    Master compression sensor does not go ON within 6.5 seconds after the master compression motor operates in the return direction.
P12     copyir.com306    Master compression sensor does not go OFF within 2 seconds after the master compression motor operates in the compress direction.
P12     copyir.com307    Master compression plate maximum position is not detected within 6.5 seconds after the master compression motor operates in thecompress direction.
P12     copyir.com309    Master     copyir.comcompression     copyir.commotor encoder sensor count did not change as the master compression motor activated in the compress directionand moved out from the home position.
P12     copyir.com316    Master     copyir.comcompression     copyir.commotor encoder sensor count did not change within 10 milliseconds after the master compression motor activated.
P13     copyir.com203    Cutter HP switch does not go OFF within 100 milliseconds after the cutter motor is activated.
P13     copyir.com204    Cutter HP switch does not go ON within 300 milliseconds after the cutter motor is activated.
P13     copyir.com205    Master     copyir.compositioning sensor is ON when the print drum rotates through the preset angle following master cutting.
P13     copyir.com221    Both the cutter HP switch and cutter stop position switch are ON at the same time.
P13     copyir.com222    Cutter HP switch does not go ON within 450 milliseconds after the cutter home positioning operation started.
P13     copyir.com231    Cutter HP switch does not go OFF within 500 milliseconds after the cutter moved out from the home position.
P13     copyir.com232    Cutter stop position switch does not go ON within 2 seconds after the cutting operation started.
P13     copyir.com233    Cutter stop position switch does not go OFF within 500 milliseconds after the cutter activates to move from the stop position to the homeposition.
P13     copyir.com234    Cutter HP switch does not go ON within 2 seconds after the cutter home positioning operation started.
P14     copyir.com114    Incorrect main     copyir.comunit data.
P14     copyir.com115    The scanner operation is not completed within the set time.
P14     copyir.com116    Timeout error for black shading compensation. (RZ3 series only)
P14     copyir.com117    Timeout error for white shading compensation. (RZ3 series only)
P14     copyir.com123    Offset adjustment not completed within set time. (RZ3 series only)
P14     copyir.com124    Gain adjustment not completed within set time. (RZ3 series only)
P14     copyir.com125    Offset adjustment not completed.
P14     copyir.com126    Gain adjustment not completed.
P14     copyir.com135    Malfunction detected during offset adjustment. (RZ3 series only)
P14     copyir.com136    Malfunction detected during offset adjustment. (RZ3 series only)
P14     copyir.com137    Malfunction detected during black shading compensation. (RZ3 series only)
P14     copyir.com138    Malfunction detected during white shading compensation. (RZ3 series only)
P14     copyir.com170    Even though the read pulse motor stopped according to the sensor detection, the stopping position does not correspond with theprogrammed position. (GA control error).
P15     copyir.com110    ABC (auto     copyir.combase     copyir.comcontrol) timeout. The original does not move from the ABC scanning position on the AF unit.
P15     copyir.com111    Operation command was made to the AF unit without 24 volts supplied to the AF unit.
P15     copyir.com130    Timeout error in receiving reply from the AF unit after command signal was sent from the Riso printer to the AF unit.
P15     copyir.com131    Riso printer received an undefined command from the AF unit.
P15     copyir.com132    Riso printer detected communication sequence error from the AF unit.
P15     copyir.com133    Communication error with AF unit (ACK or NAK error).
P15     copyir.com134    Riso printer could not send command to the AF unit within the set time.
P15     copyir.com160    AF unit detection signal went OFF while the AF unit is in operation.
P15     copyir.com4    Communication error with AF     copyir.comCPU.
P17     copyir.com20    Solenoid counter is not connected.
P18     copyir.com531    Print drum lock sensor is still ON even after 100 milliseconds after the print drum lock solenoid is activated.
P19     copyir.com207    TPH pressure sensor does not go OFF within 2 seconds after the thermal     copyir.compressure motor activates in the decompressing direction, orduring home positioning operation.
P19     copyir.com208    TPH pressure sensor does not go ON within 2 seconds after the thermal     copyir.compressure motor activates in the decompressing direction.
P19     copyir.com216    TPH pressure sensor does not go OFF within 500 millisecond after the thermal     copyir.compressure motor activates in the compressing direction.
P19     copyir.com217    TPH pressure sensor does not go ON within 2 seconds after the thermal     copyir.compressure motor activates in the compressing direction.
P20     copyir.com415    Paper     copyir.comejection     copyir.comwing home sensor does not go OFF within 7,000 milliseconds after the paper ejection wing motor activates in thecounterclockwise direction from the home position.
P20     copyir.com416    Overload current was detected in the paper     copyir.comejection motor.
P20     copyir.com437    Paper     copyir.comejection encoder sensor status does not change within 10 milliseconds after the paper     copyir.comejection motor is activated.
P24     copyir.com539    Inking     copyir.commotor encoder sensor status does not change within 20 milliseconds after the inking     copyir.commotor is activated.
P25     copyir.com26    Battery voltage was below 2.3 volts (too low) when the power is turned ON.
P92     copyir.com570    EEPROM on the print drum PCB was being accessed while the print drum was in releasing action from the machine.
P93     copyir.com932    No reply from the NET     copyir.comC network interface card while accessing to the network interface card.
P93     copyir.com933    No response from NET     copyir.comC for 90 seconds during NET     copyir.comC initialization.
P94     copyir.com225    TPH code does not match with the machine code when the power is turned ON with the master     copyir.commaking unit in operating position or whenthe master     copyir.commaking unit is inserted in operating position while the power is ON.
P95     copyir.com59    Machine serial     copyir.comnumber information sent from SH     copyir.comPCB does not match with the machine serial number information in the MCTL PCB.
P96     copyir.com171    TPH resistance value not input.
P96     copyir.com172    Scanner adjustment not completed.
P96     copyir.com433    Paper size width potentiometer test     copyir.commode setting is not completed.
P96     copyir.com569    Either the print drum color information or ink category information is still not input.
P96     copyir.com613    Print pressure data missing.
P98     copyir.com119    Image processing PCB trouble.
P98     copyir.com120    Scanner communication problem. (RZ3 series only)
P98     copyir.com129    Faulty Scanner GA PCB. (RZ3 series only)
P98     copyir.com2    No reply from Mini     copyir.comRosa PCB when the machine power is turned ON even though the Rosa connection signal is ON.
P98     copyir.com245    Master transfer time     copyir.comout error during master making (Write pulse motor error).
P98     copyir.com246    Master transfer time     copyir.comout error during master making (Load pulse motor error).
P98     copyir.com38    Machine data on EEPROM does not match with that on the SH     copyir.comPCB
P98     copyir.com39    Improper EEPROM on the SH     copyir.comPCB.
P98     copyir.com46    The DIMM capacity does not match.
P98     copyir.com5    Hardware error.
P98     copyir.com51    Touch     copyir.companel communication error
P98     copyir.com53    Failure in calling out the saved Memory settings (program, mode, user paper information).
P98     copyir.com54    Failure in saving the Memory settings (program, mode, user paper information).
P98     copyir.com55    Machine type code from SH     copyir.comPCB does not match with the machine information on the H8     copyir.comPCB.
P98     copyir.com6    FRAM checksum error.
P98     copyir.com614    Vertical print position data missing.
P98     copyir.com63    The test     copyir.commode memory data stored was outside the adjustment range.
P98     copyir.com64    An undefined command was sent in communication between SH     copyir.comPCB and MCTL PCB.
P98     copyir.com65    Communication error 01 between SH     copyir.comPCB and MCTL PCB (MCTL PCB side).
P98     copyir.com67    Communication error 03 between SH     copyir.comPCB and MCTL PCB (MCTL PCB side).
P98     copyir.com68    Communication error 04 between SH     copyir.comPCB and MCTL PCB (MCTL PCB side).
P98     copyir.com69    Communication error 05 between SH     copyir.comPCB and MCTL PCB (MCTL PCB side).
P98     copyir.com7    Mini Rosa PCB not connected.
P98     copyir.com70    Communication error 06 between SH     copyir.comPCB and MCTL PCB (MCTL PCB side).
P98     copyir.com71    Communication error 07 between SH     copyir.comPCB and MCTL PCB (MCTL PCB side).
P98     copyir.com72    Communication error 08 between SH     copyir.comPCB and MCTL PCB (MCTL PCB side).
P98     copyir.com73    Communication error 09 between SH     copyir.comPCB and MCTL PCB (MCTL PCB side).
P98     copyir.com74    Communication error 10 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com75    Communication error 11 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com76    Communication error 12 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com77    Communication error 13 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com78    Communication error 14 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com79    Communication error 15 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com80    Communication error 16 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com81    Communication error 17 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com82    Communication error 18 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com83    Communication error 19 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com84    Communication error 20 between SH     copyir.comPCB and MCTL PCB (SH     copyir.comPCB side)
P98     copyir.com934    Main read/write communication error (detected by read/write side).
P98     copyir.com935    Main read/write communication error (detected by machine side).
P98     copyir.com937    Serial number data missing.
P98     copyir.com938    FRAM version     copyir.comdown.