Your browser does not support JavaScript! > ریکوآفشیو Ricoh Aficio 1018

   کانال تلگرام کپی ایران

(0) محصول
پنج شنبه, 05 آبان 2827 06:03

ریکوآفشیو Ricoh Aficio 1018

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات ریکو براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس  مانوئلهاو رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

 

 

 

101    Exposure Lamp Error
The standard white level was not detected properly when scanning the white plate    • Exposure lamp defective• Exposure lamp stabilizer defective • Exposure lamp connector defective • Dirty scanner mirror or scanner mirror out of position • SBU board defective • SBU connector defective • Lens block out of position • Incorrect position or width of white plate scanning
120    Scanner home position error 1
The scanner home position sensor does not detect the off condition during initialization or copying ( copyir.com )     • Scanner home position sensor defective • Scanner drive motor defective • Scanner home position sensor connector defective • Scanner drive motor connector defective • IOB board defective
121    Scanner home position error 2
The scanner home position sensor does not detect the on condition during initialization or copying ( copyir.com )     • Scanner home position sensor defective • Scanner drive motor defective • Scanner home position sensor connector defective • Scanner drive motor connector defective • IOB board defective
122    Scanner home position error 3
The scanner home position sensor detects the on condition while the scanner is returning to the home position ( copyir.com )     • Scanner home position sensor defective • Scanner drive motor defective • Scanner home position sensor connector defective • Scanner drive motor connector defective • IOB board defective
123    Scanner home position error 4
The scanner home position sensor does not detect the on condition after the scanner returns to the home position ( copyir.com )     • Scanner home position sensor defective • Scanner drive motor defective • Scanner home position sensor connector defective • Scanner drive motor connector defective • IOB board defective
130    Communication Error between BiCU and SBU
The BiCU board cannot detect the SBU connect signal ( copyir.com )     • The flat cable between the BiCU board and the SBU has a poor connection • The flat cable between the BiCU board and the SBU damaged • BiCU board defective • SBU defectiv
192    Automatic SBU adjustment error
During the automatic SBU adjustment, the machine detects that the white level read from the white plate or paper is out of range ( copyir.com )     • Exposure lamp defective • SBU auto adjustment was not done correctly • SBU defective • BiCU board defective • Exposure lamp stabilizer defective
194    SBU White Level Detection Error
The automatic SBU adjustment failed twenty times consecutively ( copyir.com )     • Exposure lamp defective • Dirty white plate • Incorrect position or width of white plate scanning • BiCU board defective • SBU board defective
302    Charge roller current leak
A current leak signal for the charge roller is detected ( copyir.com )     • Charge roller damaged • High voltage supply board defective • Poor connection of the PCU
320    Polygonal mirror motor error
The polygon mirror motor does not reach operating speed within 10 seconds after the motor ON signal is sent, or does not turn on within one of the 200 ms check intervals during operation ( copyir.com )     • Polygon mirror motor defective • Poor connection between the polygonal mirror motor driver and the BiCU board • Damaged cable between BiCU/IOB and polygonal mirror motor driver • BiCU board defective
321    No laser writing signal (F-GATE) error
The laser writing signal (F-GATE) fails to turn Low after the laser crosses 5 mm on the drum surface from the laser writing start position ( copyir.com )     • BiCU board defective • IMB board defective • The fax controller or printer controller has a poor connection • Fax controller or printer controller defective
322    Laser synchronization error
The main scan synchronization detector board cannot detect the laser synchronization signal for more than 5 consecutive 100 ms intervals ( copyir.com )     • Poor connection between the LD unit and the BICU board • Damaged cable between BiCU and LD unit • LD unit out of position • LD unit defective • BiCU board defective
390    TD sensor error
The TD sensor outputs less than 0 ( copyir.com ) 2 V or more than 4 ( copyir.com ) 0 V 10 times consecutively during copying ( copyir.com )     • TD sensor abnormal • Poor connection of the PCU
391    Development bias leak
A development bias leak signal is detected ( copyir.com )     • Poor connection of the PCU • High voltage supply board defective
392    TD sensor initial setting error
TD sensor initial setting is not performed correctly ( copyir.com )     • ID sensor defective • No developer • Drum does not turn • Development roller does not turn • Poor connection of the PCU • The voltage is not applied to charge roller
401    Transfer roller leak error 1
A current leak signal for the transfer roller is detected ( copyir.com )  A current feedback signal for the transfer roller is not detected ( copyir.com )     • High voltage supply board defective • Poor connection of the PCU • Transfer/separation unit set incorrectly • Transfer roller damaged
402    Transfer roller leak error 2
A current leak signal for the transfer roller is detected ( copyir.com )  A current feedback signal for the transfer roller is not detected ( copyir.com )     • High voltage supply board defective • Poor connection of the PCU • Transfer/separation unit set incorrectly • Transfer roller damaged
500    Main motor lock
A main motor lock signal is not detected for more than 7 consecutive checks (700 ms) after the main motor starts to rotate, or the lock signal is not detected for more than 7 consecutive checks during rotation after the last signal ( copyir.com )     • Too much load on the drive mechanism • Main motor defective
503    Upper paper tray lift motor malfunction (optional paper tray units)
The paper lift sensor fails to activate twice continuously after the tray lift motor has been on for 18 seconds ( copyir.com )     • Paper lift sensor defective • Tray lift motor defective • Too much load on the drive mechanism • Poor tray lift motor connection
504    Lower paper tray lift motor malfunction (optional two-tray paper tray unit)
The paper lift sensor fails to activate twice continuously after the tray lift motor has been on for 18 seconds ( copyir.com )     • Paper lift sensor defective • Tray lift motor defective • Too much load on the drive mechanism • Poor tray lift motor connection
506    Paper feed motor lock (optional paper tray units)
A motor lock signal is not detected for more than 1 ( copyir.com ) 5 s or the lock signal is not detected for more than 1 ( copyir.com ) 0 s during rotation ( copyir.com )     • Paper feed motor defective • Too much load on the drive mechanism
541    Fusing thermostat/thermistor open
The fusing temperature detected by the thermistor is below 10°C for 5 seconds after the main power switch is turned on ( copyir.com )     • Fusing thermostat defective or out of position • Fusing thermistor defective or out of position • Power supply board defective
542    Fusing temperature warm-up error
The fusing temperature does not reach 80°C within 30 seconds after the main switch is turned on ( copyir.com )     • Fusing thermistor defective or out of position • Fusing lamp open • Fusing thermostat open • Fusing thermofuse open • Power supply board defective
543    Fusing overheat error
A fusing temperature of over 230°C is detected for 1 second by the fusing thermistor ( copyir.com )     • Fusing thermistor defective • Power supply board defective
544    Fusing low temperature error
A fusing temperature of lower than 100°C is detected for 1 second by the fusing thermistor during operation or stand-by mode ( copyir.com )     • Fusing lamp open • Fusing thermistor defective • Power supply board defective • Fusing thermistor open • Fusing thermostat open
546    Unstable fusing temperature
The fusing temperature does not rise 3 °C or more within 5 seconds after the fusing lamp has been on over 8 seconds ( copyir.com )     • Thermistor defective • Power supply unit defective
547    Zero cross signal malfunction
Zero cross signals are not detected within 5 seconds after the main power switch is turned on, or are not detected within 1 second after operation begins ( copyir.com )     • Power supply board defective • IOB defective • BiCU defective
620    Communication error between IOB and ADF
The IOB does not receive a response from the ADF main board for 4 seconds or more ( copyir.com )     • Poor connection between the IOB and ADF main board (DF connector) • ADF main board defective • IOB defective
691    Communication error between BiCU and fax controller
The BiCU board cannot communicate with the fax controller ( copyir.com )     • Poor connection between the BiCU board and the fax controller • BiCU board defective • Fax controller defective
692    Communication error between BiCU and printer controller
The BiCU board cannot communicate with the printer controller ( copyir.com )     • Poor connection between the BiCU board and the printer controller ( copyir.com )  • BiCU board defective • Printer controller defective
695    Fax firmware error
The fax program cannot be started ( copyir.com )     • The fax firmware download has not been completed correctly ( copyir.com )  Try again ( copyir.com )
760    ADF gate abnormal
The ADF Gate signal line between the ADF main board and the IOB is disconnected ( copyir.com )     • ADF main board defective • Input/output board defective • Poor connection (ADF Gate line) between the ADF main board and the IOB ( copyir.com )
900    Electrical total counter error
The electrical total counter does not work properly ( copyir.com )     • NVRAM defective
901    Mechanical total counter
The mechanical total counter does not work properly ( copyir.com )     • Mechanical total counter defective • IOB defective • Disconnected mechanical total counter
921    IMB memory controller error
A memory control job is not completed within a certain period ( copyir.com )     • IMB defective • BiCU defective • Poor connection between IMB and BiCU
922    IMB DRAM error
The machine detects a discrepancy in the IMB DRAM write/read data during its write/read test (done at power off/on and at recovery from low power or night/off mode) ( copyir.com )     • IMB defective • BiCU defective • Poor connection between BiCU and IMB
924    Optional DRAM error
The machine detects a discrepancy in the Optional DRAM write/read data during its write/read test (done at power off/on and at recovery from low power or night/off mode) ( copyir.com )     • Non-supported DRAM connected • Poor connection between IMB and optional DRAM • Optional DRAM defective • IMB defective • BiCU defective
925    IMB non-connected error
IMB is not connected ( copyir.com )  This SC only appears with B040 and B043 version machines ( copyir.com )     • IMB is not connected • Poor connection between BiCU and IMB • IMB defective • BiCU defective
926    Memory capacity error
The machine detects a discrepancy between the memory capacity detected during the memory check at power on and the check at recovery from low power or night/off mode ( copyir.com )     • Poor connection between optional DRAM and IMB • Optional DRAM defective • IMB defective • BiCU defective
981    NVRAM error
The machine detects a discrepancy in the NVRAM write/read data when attempting to save actual data to the NVRAM (i ( copyir.com ) e ( copyir.com )  during actual use) ( copyir.com )     • NVRAM defective • Poor connection between BiCU and NVRAM • NVRAM is not connected • BiCU defective
990    Communication error between BICU and IOB
The BiCU board cannot communicate with the IOB ( copyir.com )     • The connection between the BiCU board and the IOB is poor ( copyir.com )  • BiCU board defective • IOB defective
999    Program version error
An incorrect type of main software was downloaded ( copyir.com )     • The main software for another machine was downloaded to this machine ( copyir.com )  Switch the machine off ( copyir.com )  Connect an IC card that has the correct firmware to the machine ( copyir.com )  Switch the

chine on, and download the firmware (see section 5 ( copyir.com ) 1 ( copyir.com ) 9) ( copyir.com )

جهت اطلاع از انواع مدلهاوقیمت دستگاههای فتوکپی رنگی لطفا کلیک کنید 

جهت اطلاع از انواع مدلهاوقیمت دستگاههای فتوکپی رومیزی لطفا کلیک کنید  

جهت اطلاع از انواع مدلهاوقیمت دستگاههای فتوکپی متوسط لطفا کلیک کنید 

جهت اطلاع از انواع مدلهاوقیمت دستگاههای ریسو گراف لطفا کلیک کنید  

جهت اطلاع از انواع مدلها وقیمت دستگاههای پلاتر لطفا کلیک کنید 

جهت اطلاع از انواع مدلها وقیمت دستگاههای فتوکپی تکثیر لطفا کلیک کنید

خواندن 2687 دفعه آخرین ویرایش در پنج شنبه, 06 تیر 1398 11:36

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب