Your browser does not support JavaScript! > ریکوآفشیوRicoh Aficio MP6500SP
(0) محصول
سه شنبه, 20 بهمن 1394 18:43

ریکوآفشیوRicoh Aficio MP6500SP

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات ریکو براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

101    Exposure Lamp Error
At trigger on, the lamp was not detected on( copyir( copyir.com com     • SBU board defective • SIOB board defective • IPU board defective • BCU board defective • Exposure lamp defective • Lamp stabilizer defective • Lamp stabilizer harness damaged, disconnected • Standard white plate dirty, disconnected or has condensation • DF white belt dirty • DF glass dirty or has condensation • Scanner mirror dirty, out of position or has condensation • Lens dirty, out of position
120    Scanner home position error 1
The scanner HP sensor does not detect the OFF condition during initialization or copying( copyir( copyir.com com     • BCU, SIOB defective • Scanner motor defective • Scanner HP sensor defective( copyir( copyir.com com  • Harness between BCU, SIOB, scanner motor disconnected( copyir( copyir.com com  • Harness between scanner HP sensor and BCU disconnected( copyir( copyir.com com  • Scanner wire, timing belt, pulley, or carriage installed incorrectly( copyir( copyir.com com
121    Scanner home position error 2
The scanner HP sensor does not detect the ON condition during initialization or copying( copyir( copyir.com com     • BCU, SIOB defective • Scanner motor defective • Scanner HP sensor defective • Harness between BCU, SIOB, scanner motor disconnected • Harness between scanner HP sensor and BCU disconnected • Scanner wire, timing belt, pulley or carriage installed incorrectly( copyir( copyir.com com
141    Black level detection error
The black level cannot be adjusted within the target during auto gain control( copyir( copyir.com com     • Harness between SBU – SIOB is disconnected( copyir( copyir.com com  • Harness between SIOB – BCU is disconnected( copyir( copyir.com com  • Defective SBU • Defective BCU
142    White level detection error
The white level cannot be adjusted to the second target level within the target during auto gain control( copyir( copyir.com com     • Dirty exposure lamp or optics section • SBU board defective • SIOB defective • IPU board defective • BCU board defective • Harnesses are disconnected( copyir( copyir.com com  • Exposure lamp defective • Lamp stabilizer defective • Scanner motor defective
143    SBU auto gain error
The white level cannot be adjusted to the first target level within the target during auto gain control( copyir( copyir.com com     • SBU board defective • SIOB board defective • IPU board defective • BCU board defective • Scanner motor defective • Exposure lamp defective • Exposure lamp stabilizer defective • Harness between exposure lamp and lamp stabilizer is disconnected • Harness between lamp stabilizer – SIOB is disconnected • Harness between SBU - SIOB is disconnected • Harness between SIOB - BCU is disconnected • Harness between SBU – IPU is disconnected • Harness between IPU - BCU is disconnected • White plate is installed incorrectly or is dirty • Scanning mirrors of the exposure unit are dirty or out of position
144    SBU transmission error
After the SBU switches on, the BCU detects one of the following conditions on the SBU: • 1 s after power on, the SYDO signal does not go high, even after 1 retry( copyir( copyir.com com  • 1 s after power on, the SYDO signal goes high, but the SBU ID could not be read after 3 attempts( copyir( copyir.com com     • SBU defective • SIOB defective • BCU defective • Harness between the SBU - SIOB is disconnected • Harness between the SIOB - BCU is disconnected • Harness between the SIOB – PSU is disconnected
161-001    IPU error
The error result of self-diagnostic by the ASIC on the BICU is detected( copyir( copyir.com com     • Defective BICU • Defective connection between BICU and SBU
161-002    IPU error
The machine detects an error during an access to the Ri( copyir( copyir.com com     • Defective BICU board
161-003    IPU error
The IPU fails to configure or initialize the DRAM( copyir( copyir.com com     • Defective BICU board
165    Copy data security unit error B829
The copy data security option is installed by not operating correctly( copyir( copyir.com com     • Copy data security card corrupted • The board is not installed or the board is defective
181    Inverter Fan Error
When the exposure lamp is triggered on, the inverter fan motor does not rotate( copyir( copyir.com com     • SIOB defective • BCU defective • Inverter fan motor defective • Harness between the inverter fan motor - SIOB is disconnected • Harness between the SIOB – BCU is disconnected • Harness between the SIOB – PSU is disconnected
182    Scanner Fan Error: Right Side
The fan located on the right side of the exposure unit is not rotating( copyir( copyir.com com     • Check the fan connections • Fan defective • Check SBU connection • SBU defective
185    CIS transmission error
Error caused during ASIC register's automatic initialization on the CIS, or during transmission between the CIS – DF( copyir( copyir.com com     • Harness between the CIS – DF is disconnected • CIS defective
186    CIS LED error
LED on the CIS causes error • During initializing, the ration of the average between leading-edge area and rearedge is beyond the permissible level (0( copyir( copyir.com com 7 – 1( copyir( copyir.com com 43)( copyir( copyir.com com  • During scanning, the shading data peak is under 32(8bit)( copyir( copyir.com com     • Harness CN210 and CN220 on ADF are disconnected( copyir( copyir.com com  • Otherwise, replace CIS( copyir( copyir.com com
187    CIS BK level error
The BK level scanned by CIS is abnormal( copyir( copyir.com com  The BK level average of R, G or B is/are not from 2 to 62( copyir( copyir.com com  0 < Calibrated BK data level < 255(10bit)( copyir( copyir.com com     • Turn off the machine( copyir( copyir.com com  • Make sure CN210 and CN220 are connected firmly( copyir( copyir.com com  • Turn on the machine( copyir( copyir.com com
188    CIS white level error
The shading data peak detected from the CIS is abnormal( copyir( copyir.com com     • CIS defective
189    CIS gray balance adjustment error
The adjustment error occurs during the test after adjusting the gray balance( copyir( copyir.com com     • CIS defective
195    Machine serial number error
The number registered for the machine serial number does not match( copyir( copyir.com com     1( copyir( copyir.com com  Confirm the correct serial number of the machine in the specifications( copyir( copyir.com com  Important: When SC195 occurs, the serial number must be input( copyir( copyir.com com  Contact your technical supervisor( copyir( copyir.com com
202    Polygon mirror motor error 1: Timeout at ON
The polygon mirror motor unit did not enter "Ready" status within 20 sec( copyir( copyir.com com  after the motor was turned on,    • The polygon mirror motor PCB connector is loose, broken, or defective • Polygon mirror motor PCB defective • Polygon mirror motor defective • IPU defective
203    Polygon mirror motor error 2: Timeout at OFF
The polygon mirror motor did not leave "Ready" within 3 sec( copyir( copyir.com com  after the motor was switched off( copyir( copyir.com com  (The XSCRDY signal did not go HIGH (inactive) within 3 sec( copyir( copyir.com com )    • The polygon mirror motor PCB connector is loose, broken, or defective • Polygon mirror motor PCB defective • Polygon mirror motor defective • IPU defective
204    Polygon mirror motor error 3: XSCRDY signal error
The polygon mirror motor "Ready" signal goes inactive (HIGH) while images are being produced or the synchronization signal is being output( copyir( copyir.com com     • Polygon mirror motor PCB connector loose, broken, defective • Polygon mirror motor PCB defective • Polygon mirror motor defective
205    Polygon mirror motor error 4: Unstable timeout
The "Ready" signal (XSCRDY) was detected as unstable for more than 20 sec( copyir( copyir.com com  while the polygon mirror motor was operating at normal speed( copyir( copyir.com com     • Electrical noise on the line with the motor signals • Polygon mirror motor PCB connector loose, broken, defective • Polygon mirror motor PCB defective • IPU defective
220    Laser synchronization detection error
The 1st laser synchronization detection unit could not detect the line synchronization signal (DETP0) within 500 ms while the polygon mirror motor was operating at normal speed( copyir( copyir.com com  Note: The unit polls for the signal every 50 ms( copyir( copyir.com com  This SC is issued after the 10th attempt fails to detect the signal( copyir( copyir.com com     • Laser synchronization board connector loose, broken, defective • Laser synchronization detection board is not installed correctly (out of alignment) • Laser synchronization board defective • IPU defective
221    Laser Synchronization Detector Error: K Leading Edge (Not LD0)
While the polygon motor is rotating normally, no synchronizing detection signal is output for black, leading edge for any LD other than LD0( copyir( copyir.com com     • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective
230    FGATE ON error: K
The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [K]( copyir( copyir.com com     • Defective ASIC • Poor connection between controller and BICU( copyir( copyir.com com  • Defective BICU
231    FGATE OFF error: K
• The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]( copyir( copyir.com com  • The PFGATE ON signal still asserts when the next job starts( copyir( copyir.com com     See SC 230 for troubleshooting details( copyir( copyir.com com
240    LD error: K
The BICU detects LDB error a few times consecutively when LDB unit turns on after LDB initialization( copyir( copyir.com com     • Worn-out LD • Disconnected or broken harness of the LD
300    Charge corona output error
The feedback voltage from the charge corona unit is detected too high 9 times( copyir( copyir.com com     • Charge corona power pack defective • Charge corona harness disconnected • Poor charge corona unit connection
303    Charge corona grid leak
When the high voltage is output to the corona grid, feedback voltage exceeds the prescribed value 9 times( copyir( copyir.com com     • Charge corona power pack defective • Charge corona harness disconnected • Poor charge corona unit connection
304    Charge grid circuit open
When high voltage goes to the corona grid, feedback voltage is more than the set value 9 times( copyir( copyir.com com  This feedback voltage is used to update PWM for output control( copyir( copyir.com com     • Charge corona unit defective or disconnected • Charge corona harness defective • Charge corona power pack is defective( copyir( copyir.com com
305    Charge corona wire cleaner error 1
The charge cleaner pad does not arrive at the home position: Motor locked within 4 s after switching on, or does not lock within 30 s( copyir( copyir.com com  Motor locked within 10 s after reversing, or does not lock within 30 s( copyir( copyir.com com     • Charge corona wire cleaner motor defective • Motor driver defective
306    Charge corona wire cleaner error 2
Charge corona motor is disconnected( copyir( copyir.com com  (The current at the charge corona motor is detected less than 83 mA( copyir( copyir.com com )    • Charge corona wire cleaner motor connector is defective or disconnected( copyir( copyir.com com
310    Potential sensor calibration error 1
During drum potential sensor calibration, the drum potential sensor output voltage does not meet specification when test voltages (–100V, –800V) are applied to the drum( copyir( copyir.com com     • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • Development power pack defective
311    Potential sensor calibration error 2
During drum potential sensor calibration, the drum potential sensor output voltage does not meet specification when test voltages (–100V, –800V) are applied to the drum( copyir( copyir.com com     • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • Development power pack defective
312    Potential sensor calibration error 3
During drum potential sensor calibration when adjusting the drum potential (VD), the drum potential sensor detects VD higher than VG (grid voltage)( copyir( copyir.com com  -or- When adjusting VD (drum surface potential of black areas after exposure), even after 5 adjustments of VG (charge corona grid potential), VD could not be set in the target range (–800±10 + VL + 130V)    • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • Development power pack defective • Charge corona unit worn out, dirty
314    Potential sensor calibration error 4
During drum potential sensor calibration when adjusting the drum potential (VH) for LD power adjustment, the first time the VH pattern is made, the drum potential sensor detects that VH is more than 500V: VH > –500 + VL + 130 V    • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • LD defective
315    Potential sensor calibration error 5
During drum potential sensor calibration, when -100V is applied to the drum, the output value is out of the prescribed range( copyir( copyir.com com     • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • Development power pack defective
316    Potential sensor calibration error 6
During drum potential sensor calibration, when -800V is applied to the drum, the output value is out of the prescribed range( copyir( copyir.com com     • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • Development power pack defective
317    Potential sensor calibration error 7
During drum potential sensor calibration, when VL is adjusted, the pattern surface potential VL pattern is not within range 0V to -400V( copyir( copyir.com com  (VL is the potential after exposing a white pattern( copyir( copyir.com com )    • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • Charge corona power pack defective • Development power pack defective
340    TD sensor output error
TD sensor output voltage (Vt), measured during each copy cycle, is detected 10 times at one of the following levels: Vt = 0( copyir( copyir.com com 5 volts or lower Vt = 4( copyir( copyir.com com 0 volts or higher    • TD sensor defective • TD sensor harness disconnected • TD sensor connector disconnected or defective • IOB defective • Toner bottle motor defective Note: When the TD sensor is defective, the toner supply is controlled using pixel count and the ID sensor( copyir( copyir.com com
341    TD sensor adjustment error 1
During the TD sensor auto adjustment, the TD sensor output voltage (Vt) is 2( copyir( copyir.com com 5 volts or higher even though the control voltage is set to the minimum value (PWM = 0)( copyir( copyir.com com  When this error occurs, SP2-906-1 reads 0( copyir( copyir.com com 00V( copyir( copyir.com com  Note: This SC is released only after correct adjustment of the TD sensor has been achieved( copyir( copyir.com com  Switching the machine off and on will cancel the SC display, but does not release ID sensor toner supply( copyir( copyir.com com     • TD sensor defective • TD sensor harness disconnected • TD sensor connector disconnected or defective • IOB defective • Toner bottle motor defective Note: When the TD sensor is defective, the toner supply is controlled using pixel count and the ID sensor( copyir( copyir.com com
342    TD sensor adjustment error 2
During the TD sensor auto adjustment, the TD sensor output voltage (Vt) does not enter the target range (3( copyir( copyir.com com 0 ± 0( copyir( copyir.com com 1V) within 20 s( copyir( copyir.com com  When this error occurs, the display of SP2-906-1 reads 0( copyir( copyir.com com 00V( copyir( copyir.com com  Note: This SC is released only after correct adjustment of the TD sensor has been achieved( copyir( copyir.com com  Switching the machine off and on will cancel the SC display, but does not release ID sensor toner supply( copyir( copyir.com com     • TD sensor defective • TD sensor harness disconnected • TD sensor connector disconnected or defective • IOB defective
345    Development output abnormal
The high voltage applied to the development unit is detected 10 times higher than the upper limit (45%) of PWM( copyir( copyir.com com     • Development power pack defective • Development bias leak due to poor connection, defective connector
350    ID sensor error 1
One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern( copyir( copyir.com com  Vsp greater than or equals 2( copyir( copyir.com com 5V Vsg less than 2( copyir( copyir.com com 5 Vsp = 0V Vsg = 0    • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty
351    ID sensor error 2
The ID sensor output voltage is 5( copyir( copyir.com com 0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern( copyir( copyir.com com     • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty
352    ID sensor error 3
For 2 s during the ID sensor pattern check, the ID sensor pattern edge voltage is not 2( copyir( copyir.com com 5V or the pattern edge is not detected within 800 ms( copyir( copyir.com com     • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty
353    ID sensor error 4
One of the following ID sensor output voltages is detected at ID sensor initialization( copyir( copyir.com com  Vsg less than 4( copyir( copyir.com com 0V when the maximum PWM input (255) is applied to the ID sensor( copyir( copyir.com com  Vsg greater than or equal to 4( copyir( copyir.com com 0V when the minimum PWM input (0) is applied to the ID sensor( copyir( copyir.com com     • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty
354    ID sensor error 5
Vsg falls out of the adjustment target (4( copyir( copyir.com com 0 ±0( copyir( copyir.com com 2V) during Vsg checking( copyir( copyir.com com     • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty
355    ID sensor error 6
The Vp value, which measures the reflectivity of the ID sensor pattern, was not in the range of -70V to -400V( copyir( copyir.com com     • Potential sensor defective • Potential sensor harness defective • Potential sensor disconnected • IOB defective • OPC unit connector defective • Charge corona power pack defective • Charge corona wire dirty, broken
401    Transfer output abnormal
When the transfer is output, the feedback voltage remains higher than 4V for 60 ms( copyir( copyir.com com     • Transfer power pack defective • Transfer current terminal, transfer power pack disconnected, damaged connector
402    Transfer output abnormal release detection
When the transfer is output, there is hardly any feedback voltage within 60 ms even with application of 24% PWM( copyir( copyir.com com     • Transfer power pack defective • Transfer unit harness disconnected • Transfer connector loose, defective
430    Quenching lamp error
At the completion of auto process control initialization, the potential of the drum surface detected by the potential sensor is more than -400V, the prescribed value( copyir( copyir.com com     • Quenching lamp defective • Quenching lamp harness disconnected • Quenching lamp connector loose, defective
440    Main motor lock
The main motor lock signal remains low for 2 seconds while the main motor is on( copyir( copyir.com com     • Drive mechanism overloaded • Motor driver board defective
441    Development motor lock
The development motor lock signal remains high for 2 seconds while the development motor is on( copyir( copyir.com com     • Drive mechanism overloaded due to toner clumping in the wasted toner path • Motor driver board defective
490    Main fan error
The main fan motor lock signal goes high for 5 s while the fan is on( copyir( copyir.com com     • Fan motor overloaded due to obstruction • Fan connector disconnected
495    Toner recycling unit error
Encoder pulse does not change for 3 s after the main motor switches on( copyir( copyir.com com     • Waste toner transport has stopped due to motor overload • Toner end sensor detective, disconnected
496    Toner collection bottle error
The toner collection bottle set switch remains off when the front door is closed( copyir( copyir.com com     • No toner collection bottle set • Poor connection of the switch connector
497    Toner collection motor error
The toner collection motor connector set signal remains off for 1 s( copyir( copyir.com com     • Toner pump motor defective • Motor connector loose, disconnected
501    Tray 1 lift malfunction
• The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate( copyir( copyir.com com  • When the tray lowers, the tray lift sensor does not go off within 1( copyir( copyir.com com 5 s( copyir( copyir.com com  • Tray overload detected when the tray is set( copyir( copyir.com com  • The lower limit sensor of the LCT does not detect the lower limit within 10 s( copyir( copyir.com com     • Tray lift motor defective, disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected, blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray( copyir( copyir.com com  • This SC will not display until the operator has pulled the tray out and pushed it in 3 times( copyir( copyir.com com  • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset( copyir( copyir.com com
502    Tray 2 lift malfunction
• The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate( copyir( copyir.com com  • When the tray lowers, the tray lift sensor does not go off within 1( copyir( copyir.com com 5 s( copyir( copyir.com com  • Tray overload detected when the tray is set( copyir( copyir.com com     • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray( copyir( copyir.com com  • This SC will not display until the operator has pulled the tray out and pushed it in 3 times( copyir( copyir.com com  • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset( copyir( copyir.com com
503    Tray 3 lift malfunction
• The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate( copyir( copyir.com com  • When the tray lowers, the tray lift sensor does not go off within 1( copyir( copyir.com com 5 s( copyir( copyir.com com  • Tray overload detected when the tray is set( copyir( copyir.com com     • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray( copyir( copyir.com com  • This SC will not display until the operator has pulled the tray out and pushed it in 3 times( copyir( copyir.com com  • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset( copyir( copyir.com com
504    Tray 4 lift malfunction
• The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate( copyir( copyir.com com  • When the tray lowers, the tray lift sensor does not go off within 1( copyir( copyir.com com 5 s( copyir( copyir.com com  • Tray overload detected when the tray is set( copyir( copyir.com com     • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray( copyir( copyir.com com  • This SC will not display until the operator has pulled the tray out and pushed it in 3 times( copyir( copyir.com com  • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset( copyir( copyir.com com
507    LCT feed motor malfunction
One of the following conditions is detected: • The LD signal from the feed motor is detected abnormal for 50 ms after the motor switches on( copyir( copyir.com com  • At power on, the motor is detected loose or disconnected( copyir( copyir.com com     • Feed motor defective • Feed motor connector disconnected • Obstacle interfering with mechanical movement of motor
510    LCT tray malfunction
One of the following conditions is detected: • When the bottom plate is lifted, the upper limit sensor does not come on for 18 s( copyir( copyir.com com  • When the bottom plate is
lowered, the lower limit sensor does not come on for 18 s( copyir( copyir.com com
• After lift begins, the upper limit sensor does not switch on before the pick-up solenoid switches on( copyir( copyir.com com  • The paper end sensor switches on during lift and the upper limit
sensor does not switch on for 2( copyir( copyir.com com 5 s, and a message prompts user to reset paper( copyir( copyir.com com     • Tray lift motor defective or connector disconnected • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective
515    Tandem rear fence motor error
One of the conditions is detected: • The return sensor does not switch on within 10 s( copyir( copyir.com com  after the rear fence motor switches on( copyir( copyir.com com  • The HP sensor does not switch on 10 s( copyir( copyir.com com  after the rear fence motor switches on( copyir( copyir.com com  • The HP sensor and return sensor switch on at the same time( copyir( copyir.com com     • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty Note • This problem will not issue the SC code on the operation panel( copyir( copyir.com com  • The machine will prompt the operator to reset tray by opening and closing it( copyir( copyir.com com  • If the problem persists, the machine will display again and the tray cannot be used( copyir( copyir.com com
520    Duplex jogger motor error 1
When the jogger fence moves to the home position, the jogger HP sensor does not turn on even if the jogger fence motor has moved the jogger fence 153( copyir( copyir.com com 5 mm( copyir( copyir.com com     • Paper or other obstacle has jammed mechanism • Sensor connector disconnected or defective • Sensor defective
521    Duplex jogger motor error 2
When the jogger fence moves from the home position, the jogger fence HP sensor does not turn off even if the jogger motor has moved the jogger fence 153( copyir( copyir.com com 5 mm( copyir( copyir.com com     • Paper or other obstacle has jammed mechanism • Sensor connector disconnected or defective • Sensor defective
531    Fusing exit motor error
The PLL lock signal was low for 2 s during motor operation( copyir( copyir.com com     • Motor lock caused by physical overload • Motor drive PCB defective
541    Fusing thermistor open
The fusing temperature detected by the center thermistor was below 0°C for 7 s( copyir( copyir.com com     • Thermistor open • Thermistor connector defective • Thermistor damaged, or out of position • Fusing temperature –15% less than the standard input voltage
542    Fusing temperature warm-up error
One of the following occurred: • After power on, or after closing the front door, the hot roller does not reach the 100°C control temperature within 25 s( copyir( copyir.com com  • 5 sec( copyir( copyir.com com  after temperature rise started, temperature remained below 21°C after 5 samplings( copyir( copyir.com com  • Fusing unit did not attain reload temperature within 48 s( copyir( copyir.com com  of the start of fusing temperature control( copyir( copyir.com com     • Fusing lamp disconnected • Thermistor warped, out of position • Thermostat not operating
543    Fusing lamp overheat error 1 (software)
Central thermistor detected a temperature of 240°C at the center of the hot roller( copyir( copyir.com com  Fusing temperature control software error    • PSU defective • IOB defective • BICU defective
544    Fusing lamp overheat error 1 (hardware)
The center thermistor or an end thermistor detected a temperature of 250°C on the hot roller( copyir( copyir.com com     • PSU defective • IOB defective • BICU defective
545    Fusing lamp overheat error 2
After hot roller reaches warmup temperature, the fusing lamps remained on at full capacity for 11 samplings (1( copyir( copyir.com com 8 s( copyir( copyir.com com  duration) while the hot roller was not rotating( copyir( copyir.com com     • Thermistor damaged, or out of position • Fusing lamp disconnected
547    Zero cross signal malfunction
One of the following conditions is detected 10 times: • When the main switch is on, the frequency measured by the number of zero cross signals for 500 ms is larger than 66Hz or smaller than 45 Hz( copyir( copyir.com com  • The interval between one zero cross signal and the next is 7( copyir( copyir.com com 5 ms or shorter 3 times consecutively for 500 ms( copyir( copyir.com com     • Noise on the ac power line
551    Fusing thermistor error 1
The end thermistor (contact type) was less than 0C (32F) for more than 7 seconds( copyir( copyir.com com     • Thermistor disconnected • Thermistor connector defective
552    Fusing thermistor error 2
The end thermistor (contact type) could not detect: • 100°C 25 seconds after the start of the warmup cycle( copyir( copyir.com com  • A change in temperature more than than 16 degrees for 5 seconds( copyir( copyir.com com  • The reload temperature with 56 seconds after the start of the fusing temperature control cycle( copyir( copyir.com com     • Fusing lamp disconnected • Thermistor bent, damaged • Thermistor position incorrect
553    Fusing thermistor error 3
The end thermistor (contact type) was at 240°C (464°F) for more than 1 second( copyir( copyir.com com  The temperature is read 10 times every second( copyir( copyir.com com  (at 0( copyir( copyir.com com 1 s intervals)( copyir( copyir.com com     • PSU defective • IOB control board defective • BICU control board defective
555    Fusing lamp error
After the start of the warmup cycle, a fusing lamp was at full power for 1( copyir( copyir.com com 8 s but the hot roller did not turn( copyir( copyir.com com     • Thermistor bent, out of position • Fusing lamp disconnected • Circuit breaker opened
557    Zero cross signal error
High frequency noise was detected on the powe r line( copyir( copyir.com com     • No action required( copyir( copyir.com com  The SC code is logged and the operation of the machine is not affected( copyir( copyir.com com
559    Fusing jam: 3 counts
At the fusing exit sensor the paper was detected late for three pulse counts (lag error), and SP1159 was on( copyir( copyir.com com     • If this SC occurs, the machine cannot be used until the service technician cancels the SC code( copyir( copyir.com com  • This SC occurs only if SP1159 has been set to "1" (On)( copyir( copyir.com com  (Default: 0 (Off))( copyir( copyir.com com
569    Fusing pressure release motor error
During copying, the HP sensor could not detect the actuator, tried again 3 times and could not detect( copyir( copyir.com com     • Motor lock because of too much load • Motor driver defective • HP sensor defective, disconnected, connector defective, harness damaged
590    Toner collection motor error
The toner collection motor sensor output does not change for 3 s while the toner collection motor is on( copyir( copyir.com com     • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing
599    1-bin Exit Motor Error (Japan Only)
The transport lock sensor output does not change within 300 ms after the motor switches on( copyir( copyir.com com     • Motor overload • Motor driver defective
620    BICU/ADF communication/timeout error
After 1 data frame is sent to the finisher MBX, an ACK signal is not received within 100 ms, and is not received after 3 retries    • Serial line connection unstable • External noise on the line
621    BICU/Finisher communication/break error
During communication with the finisher MBX, the BICU received a break (Low) signal from the finisher( copyir( copyir.com com     • Serial line connection unstable • External noise on the line
623    BICU/Tray 1 to 4 communication/timeout error
After 1 data frame is sent to the trays, an ACK signal is not received within 100 ms, and is not received after 3 retries( copyir( copyir.com com     • Serial line connection unstable • External noise on the line
625    VBCU-DTMB (DMC1) communication error
Communication between the VBCU and DMC (main) was interrupted( copyir( copyir.com com  An ACK/NAK signal was not received within 100 ms after a data frame was sent and three retries failed( copyir( copyir.com com     • Check the DTMB harness connections at the DTMB and VBCU • DTMB defective • PSU defective • VBCU defective • 5V power supply defective
626    BICU, LCT communication/timeout error
After 1 data frame is sent to the LCT, an ACK signal is not received within 100 ms, and is not received after 3 retries( copyir( copyir.com com     • Serial line connection unstable • External noise on the line
627    BICU, LCT communication/break reception error
During communication with the LCT, the BICU received a break (Low) signal( copyir( copyir.com com     • Serial line connection unstable • External noise on the line
628    Fan folder communication error 1
The main machine issued a timeout three failed attempts to communicate with the fan folder unit( copyir( copyir.com com  Possible causes: • There was no answer from the fan folder within 100 ms in response to data sent from the main machine( copyir( copyir.com com  • The fan folder unit was switched off while folding was in progress( copyir( copyir.com com  • The main machine received an illegal command from the fan folder( copyir( copyir.com com  • 60 sec( copyir( copyir.com com  after the main machine fed the document to the fan folder, the fan folder failed to notify the main machine that the folded document has exited the fan folder( copyir( copyir.com com     • Fan folder not connected to main machine • Fan folder main control unit connector loose, broken, defective • Fan folder main control unit defective
629    Fan folder communication error 2: Cross Folder
There was no answer from the fan folder within 100 ms in response to data sent from the main machine( copyir( copyir.com com     • Fan folder not connected to main machine • Fan folder main control unit connector loose, broken, defective • Fan folder main control unit defective
632    Charge Unit Device Error 1    
633    Charge Unit Device Error 2    
634    Charge Unit Device Error 3    
635    Charge Unit Device Error 4    
636-01    SD Card Error: Expanded authentication module error
There is no expanded authentication module in the machine( copyir( copyir.com com  The SD card or the file of the expanded authentication module is broken( copyir( copyir.com com  There is no DESS module in the machine( copyir( copyir.com com     • No expanded authentication module • Defective SD card • No DESS module
636-02    SD Card Error: Version error
The version of the expanded authentication module is not correct( copyir( copyir.com com     • Incorrect module version
641    Engine-to-controller communication error
The controller sent a frame to the main machine engine but there was no response as demanded by RAPI protocol( copyir( copyir.com com  The frame was sent 3 times at 100 ms intervals( copyir( copyir.com com  This SC was issued after the 3rd attempt failed( copyir( copyir.com com     • Examine the connection between the controller and the engine board( copyir( copyir.com com  • Replace the engine board if the error is frequent( copyir( copyir.com com
650    NRS Modem Communication Error
One of the following factors could be the cause of this error: • In the User Tools, check the settings for the dial-up user name and dial-up password( copyir( copyir.com com  • Modem has been disconnected( copyir( copyir.com com  • Modem board disconnected( copyir( copyir.com com     Check the following for a machine that is using Cumin (NRS modem): • An error was returned during the dialup connection • A network was detected at startup • At startup, the machine detected that the NIB was disabled, or did not detect a modem board
651    Illegal Remote Service Dial-up
An expected error occurred when Cumin-M dialed up the NRS Center( copyir( copyir.com com     • Software bug • No action is required because only the count is logged
670    Engine Startup Error
At power on or after the machine leaves the energy conservation mode: • ENGRDY signal does not assert • IPURDY signal does not assert After power on and the prescribed time has elapsed: • No EC response from the engine • No PC response from the engine • No SC response from the engine During machine operation mode: • Write to Rapi drive failure (could not locate destination on the PCI) • After the /ENGRDY signal asserts with no effect( copyir( copyir.com com     • BICU O Controller Board disconnected • BICU board defective • Controller board defective • Mother board defective • Software error; switch off/on, if that fails, change the engine firmware • PSU-E or PSU-C defective
671    Illegal Engine Board
An illegal engine board was detected by the firmware at power on( copyir( copyir.com com     • Replace BICU
672    Controller Startup Error
The line between the controller board and the operation panel does not open correctly when the machine is powered on, or after the machine was powered on communication between the controller and operation panel is suspended( copyir( copyir.com com  The controller board and operation panel could not exchange the handshake (FDH) and acknowledge (FEH) signals within 15 s of the operation panel reset after power on, or after 2 retries there was no response to the transmission line confirmation command issued every 30 s from the operation panel to the controller board( copyir( copyir.com com     • Controller board defective • Controller board installed incorrectly • Operation panel harness connection loose or incorrect
701    ADF bottom plate motor error
• Bottom plate position sensor does not detect the plate after the bottom plate lift motor switches on to lift the plate( copyir( copyir.com com  • Bottom plate HP sensor does not detect the plate after the bottom plate motor reverses to lower the plate( copyir( copyir.com com     • Bottom plate position sensor defective • Bottom plate HP sensor defective • Bottom plate motor defective • ADF main board defective
705    ARDF bottom plate lift motor
The bottom plate HP sensor does not detect the home position of the bottom plate after the bottom plate lift motor switches on and lowers the bottom plate( copyir( copyir.com com  The bottom plate position sensor does not detect the position of the plate after the lift motor switches on and raises the bottom plate( copyir( copyir.com com     • ARDF feed motor disconnected, defective • Bottom plate HP sensor disconnected, defective • ARDF main board defective
720    Finisher transport motor error
The encoder pulse of the finisher transport motor does not change state (high/low) within 600 ms and does not change after 2 retries( copyir( copyir.com com     • Finisher transport motor defective • Transport motor harness disconnected, or defective • Finisher main board defective
721    Finisher jogger motor error
• The finisher jogger HP sensor remains de-activated for more 1,000 pulses when returning to home position( copyir( copyir.com com  • The finisher jogger HP sensor remains activated for more than 1,000 pulses when moving away from home position    • Jogger HP sensor defective • Jogger mechanism overload • Jogger motor defective (not rotating) • Finisher main board defective • Harness disconnected or defectiv
724    Finisher staple hammer motor error (D460)
The staple hammer motor did not return to the home position within the prescribed time (340 ms)( copyir( copyir.com com     • Staple hammer HP sensor loose, broken, defective • Electrical overload on the stapler drive PCB elect • Staple hammer motor defective • Finisher main board defective
725    Exit guide motor
The status of the exit guide sensor did not change at the prescribed time during operation of the exit guide( copyir( copyir.com com     Exit guide open sensor loose, broken, defective( copyir( copyir.com com  Exit guide motor defective Finisher main board defective
726    Front shift jogger motor error (B703)
The sides fences do not retract within the prescribed time after the shift jogger motor switches on( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective
727    Rear shift jogger motor (B703)
The side fences do not retract within the prescribed time after the shift jogger motor switches on( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     Motor harness disconnected, loose, defective
Motor defective
Motor overload
HP defective
728    Shift jogger retraction motor error (B703)
The side fences do not retract within the prescribed time after the retraction motor switches on( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective
740    Finisher corner stapler motor error
The stapler motor does not switch off within the prescribed time after operating( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Staple jam • Number of sheets in the stack exceeds the limit for stapling • Stapler motor disconnected, defective
741    Finisher corner stapler rotation motor error
The stapler does not return to its home position within the specified time after stapling( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Stapler rotation motor disconnected, defective • Stapler rotation motor overloaded due to obstruction • Stapler rotation HP sensor disconnected, defective
742    Finisher stapler movement motor error
The stapler HP sensor is not activated within the specified time after the stapler motor turned on( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Stapler movement motor disconnected, defective • Stapler movement motor overloaded due to obstruction • Stapler HP sensor disconnected, defective
743    Booklet stapler motor error 1
The front stapler unit saddle-stitch motor does not start operation within the specified time( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Front motor disconnected, defective • Front motor overloaded due to obstruction
744    Booklet stapler motor error 2
The rear stapler unit saddle-stitch motor does not start operation within the specified time( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Rear motor disconnected, defective • Rear motor overloaded due to obstruction
745    Feed-Out Belt Motor Error (D373/B830)
The stack feed-out belt HP sensor does not activate within the specified time after the stack feed-out belt motor turns on( copyir( copyir.com com  The 1st detection failure causes a jam error, and the 2nd failure causes this SC code( copyir( copyir.com com     If the motor is operating 1( copyir( copyir.com com  Stack feed-out HP sensor harness loose, broken, defective 2( copyir( copyir.com com  Stack feed-out HP sensor defective If the motor is not operating: 1( copyir( copyir.com com  Feed-out motor blocked by an obstruction 2( copyir( copyir.com com  Feed-out motor harness loose, broken, defective 3( copyir( copyir.com com  Feed-out motor defective 4( copyir( copyir.com com  Booklet finisher main board defective
746    Stack Plate Motor Error 1: Front Motor (B830)
The stack plate HP sensor (front) does not activate within 500 ms after the motor turns on( copyir( copyir.com com  The 1st detection failure causes a jam error, and the 2nd failure causes this SC code( copyir( copyir.com com     If the motor is operating 1( copyir( copyir.com com  Front stack plate HP sensor harness loose, broken, defective 2( copyir( copyir.com com  Front stack plate HP sensor defective If the motor is not operating: 1( copyir( copyir.com com  Motor blocked by an obstruction 2( copyir( copyir.com com  Motor harness loose, broken, defective 3( copyir( copyir.com com  Motor defective 4( copyir( copyir.com com  Booklet finisher main board defective
747    Stack Plate Motor Error 2: Center Motor (B830)
The stack plate HP sensor (center) does not activate within 500 ms after the motor turns on( copyir( copyir.com com  The 1st detection failure causes a jam error, and the 2nd failure causes this SC code( copyir( copyir.com com     If the motor is operating 1( copyir( copyir.com com  Center stack plate HP sensor harness loose, broken, defective 2( copyir( copyir.com com  Center stack plate HP sensor defective If the motor is not operating: 1( copyir( copyir.com com  Motor blocked by an obstruction 2( copyir( copyir.com com  Motor harness loose, broken, defective 3( copyir( copyir.com com  Motor defective 4( copyir( copyir.com com  Booklet finisher main board defective
748    Stack Plate Motor Error 3: Rear Motor (B830)
The stack plate HP sensor (rear) does not activate within 500 ms after the motor turns on( copyir( copyir.com com  The 1st detection failure causes a jam error, and the 2nd failure causes this SC code( copyir( copyir.com com     If the motor is operating 1( copyir( copyir.com com  Rear stack plate HP sensor harness loose, broken, defective 2( copyir( copyir.com com  Rear stack plate HP sensor defective If the motor is not operating: 1( copyir( copyir.com com  Motor blocked by an obstruction 2( copyir( copyir.com com  Motor harness loose, broken, defective 3( copyir( copyir.com com  Motor defective 4( copyir( copyir.com com  Booklet finisher main board defective
750    Finisher tray 1 (upper tray lift) motor error
The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Tray lift motor disconnected, defective • Upper tray paper height sensor disconnected, defective • Finisher main board connection to motor loose • Finisher main board defective
753    Return roller motor error
Occurs during the operation of the lower tray pressure motor( copyir( copyir.com com     • Motor harness disconnected, loose, defective • Motor overloaded • Home position sensor harness disconnected, loose, defective • Home position defective
755    Shift Motor Error: 3K Finisher (B830)
The shift tray half-turn sensors: Failed twice to detect the shift tray at the home position at the specified time( copyir( copyir.com com  -or- Failed twice to detect that the shift tray had left the home position( copyir( copyir.com com     If the motor is operating 1( copyir( copyir.com com  Half-turn sensor 1, 2 harnesses loose, broken, defective 2( copyir( copyir.com com  One of the half-turn sensors is defective If the motor is not operating: 1( copyir( copyir.com com  Motor blocked by an obstruction 2( copyir( copyir.com com  Motor harness loose, broken, defective 3( copyir( copyir.com com  Motor defective 4( copyir( copyir.com com  Finisher main board defective
760    Finisher punch motor error
The punch HP sensor is not activated within the specified time after the punch motor turned on( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Punch HP sensor disconnected, defective • Punch motor disconnected, defective • Punch motor overload due to obstruction
761    Finisher folder plate motor error
The folder plate moves but is not detected at the home position within the specified time( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction
763    Punch movement motor error
Occurs during operation of the punch unit( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Motor harness disconnected, loose, defective • Motor defective
764    Paper position sensor slide motor error
Occurs during operation of the punch unit( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Motor harness disconnected, loose, defective • Motor defective
765    Folding unit bottom fence lift motor
The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Motor harness disconnected, loose, defective • Motor defective
766    Clamp roller retraction motor error
The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Motor harness disconnected, loose, defective • Motor defective
767    Stack junction gate motor error
Occurs during operation of the punch unit( copyir( copyir.com com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code( copyir( copyir.com com     • Motor harness disconnected, loose, defective • Motor overload • Motor defective
770    Cover interposer tray bottom plate motor error
After the motor starts to raise the bottom plate, the bottom plate position sensor does not detect the plate at the specified time (3 s)( copyir( copyir.com com  After the motor starts to lower the bottom plate, the bottom plate HP sensor does not detect the bottom plate( copyir( copyir.com com     • Bottom plate position sensor, disconnected, defective • Bottom plate HP sensor disconnected, defective
775    Jogger Top Fence Motor: 3K Finisher B830
The top fence HP sensor detected that: The top fence did not arrive at the home position within the specified number of pulses( copyir( copyir.com com  -or- The top fence failed to leave the home position within the specified number of pulses( copyir( copyir.com com     If the jogger top fence motor is operating: 1( copyir( copyir.com com  Top fence HP sensor harness loose, broken, defective 2( copyir( copyir.com com  Top fence HP sensor defective If the jogger top fence motor is not operating: 1( copyir( copyir.com com  Motor blocked by an obstruction 2( copyir( copyir.com com  Motor harness loose, broken, defective 3( copyir( copyir.com com  Motor defective 4( copyir( copyir.com com  Finisher main board defective
776    Jogger Bottom Fence Motor (B830)
The bottom fence HP sensor detected that: The bottom fence did not arrive at the home position at the specified time( copyir( copyir.com com  -or- The bottom fence failed to leave the home position at the specified time( copyir( copyir.com com     If the jogger bottom fence motor is operating: 1( copyir( copyir.com com  Bottom fence HP sensor harness loose, broken, defective 2( copyir( copyir.com com  Bottom fence HP sensor defective If the jogger bot
778-1    Horizontal Transport Motor Error Multi Folder (D454)
The motor drive PCB detected an error at the motor( copyir( copyir.com com     • Motor harness or connector loose, broken, defective • Motor or motor drive board defective
778-2    Top Tray Exit Motor Multi Folder (D454)
The motor drive PCB detected an error at the motor( copyir( copyir.com com     • Motor harness or connector loose, broken, defective • Motor or motor drive board defective
778-3    Top Tray JG Motor Multi Folder (D454)
The top tray JG HP sensor did not detect the top tray junction gate at (or out of) its home position( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • Top tray JG HP sensor dirty • Sensor harness or connector loose, broken, defective • Top tray JG motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
778-4    Entrance JG Motor Multi Folder (D454)
The entrance junction gate HP sensor did not detect the entrance junction gate at (or out of) its home position( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • Entrance JG HP sensor dirty • Sensor harness or connector loose, broken, defective • Entrance JG motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
779    Z-fold stopper 1 Motor error
The bottom fence HP sensor detected that: The bottom fence did not arrive at the home position at the specified time( copyir( copyir.com com  -or- The bottom fence failed to leave the home position at the specified time( copyir( copyir.com com     • Motor overcurrent • Motor driver overheat • Motor harness loose
780    Z-Fold feed motor error
The feed motor does not attain the prescribed speed within the specified time( copyir( copyir.com com     • Feed motor disconnected, defective • Feed motor overloaded due to obstruction • Feed motor lock
781    Z-Fold lower stopper motor
The lower stopper motor does not attain the prescribed speed within the specified time( copyir( copyir.com com     • Lower stopper motor disconnected, defective • Lower stopper motor overloaded due to obstruction • Lower stopper HP sensor disconnected, defective
782    Z-Fold upper stopper motor
The upper stopper was not detected at the home position after the motor remained on long enough to move it 128( copyir( copyir.com com 7 mm( copyir( copyir.com com     • Upper stopper motor disconnected, defective • Upper stopper motor overloaded due to obstruction • Upper stopper HP sensor disconnected, defective
783-1    2nd Stopper Motor Error Multi Folder (D454)
The 2nd stopper HP sensor did not detect the 2nd stopper in (or out of) its home position within the prescribed time( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • 2nd stopper HP sensor dirty • Sensor harness or connector loose, broken, defective • 2nd stopper motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
783-10    Fold Plate Motor Error Multi Folder (D454)
The fold plate HP sensor did not detect the fold plate in (or out of) its home position within the prescribed time( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • Fold plate HP sensor dirty • Sensor harness or connector loose, broken, defective • Fold plate motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
783-11    Jogger Fence Motor Multi Folder (D454)
The jogger fence HP sensor did not detect the jogger fence in (or out of) its home position within the prescribed time( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • Jogger fence HP sensor dirty • Sensor harness or connector loose, broken, defective • Jogger fence motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
783-12    Positioning Roller Motor Error Multi Folder (D454)
The positioning roller HP sensor did not detect the positioning roller in (or out of) its home position within the prescribed time( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • Positioning roller HP sensor dirty • Sensor harness or connector loose, broken, defective • Positioning roller motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
783-13    FM2 Direct-Send JG Motor Multi Folder (D454)
The direct-send JG HP sensor did not detect the direct-send JG in (or out of) its home position within the prescribed time( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • FM2 direct-send JG HP sensor dirty • Sensor harness or connector loose, broken, defective • FM2 direct-send JG motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
783-14    FM6 Pawl Motor Multi Folder (D454)
The FM6 pawl HP sensor did not detect the FM6 pawl in (or out of) its home position( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • FM6 pawl HP sensor dirty • Sensor harness or connector loose, broken, defective • FM6 pawl motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
783-2    3rd Stopper Motor Error Multi Folder (D454)
The 3rd stopper HP sensor did not detect the 3rd stopper in (or out of) its home position within the prescribed time( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • 3rd stopper HP sensor dirty • Sensor harness or connector loose, broken, defective • 3rd stopper motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
783-3    1st Fold Motor Error Multi Folder (D454)
The motor drive PCB detected an error at the motor( copyir( copyir.com com     • Motor harness or connector loose, broken, defective • Motor or motor drive board defective
783-4    2nd Fold Motor Error Multi Folder (D454)
The motor drive PCB detected an error at the motor( copyir( copyir.com com     • Motor harness or connector loose, broken, defective • Motor or motor drive board defective
783-5    Crease Motor Error Multi Folder (D454)
The motor drive PCB detected an error at the motor( copyir( copyir.com com     • Motor harness or connector loose, broken, defective • Motor or motor drive board defective
783-6    Dynamic Roller Transport Motor Error Multi Folder (D454)
The motor drive PCB detected an error at the motor( copyir( copyir.com com     • Motor harness or connector loose, broken, defective • Motor or motor drive board defective
783-7    Reg( copyir( copyir.com com  Roller Transport Motor Error Multi Folder (D454)
The motor drive PCB detected an error at the motor( copyir( copyir.com com     • Motor harness or connector loose, broken, defective • Motor or motor drive board defective
783-8    Dynamic Roller Lift Motor Error Multi Folder (D454)
The dynamic roller HP sensor did not detect the dynamic roller in (or out of) its home position within the prescribed time( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • Dynamic roller HP sensor dirty • Sensor harness or connector loose, broken, defective • Dynamic roller lift motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
783-9    Registration Roller Release Motor Error Multi Folder (D454)
The registration roller HP sensor did not detect the registration roller in (or out of) its home position within the prescribed time( copyir( copyir.com com  The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code( copyir( copyir.com com     • Registration roller HP sensor dirty • Sensor harness or connector loose, broken, defective • Registration roller release motor harness or connector loose, broken, defective • Sensor defective • Motor or motor drive board defective
784    Z-fold timing unit fold timing sensor adjustment error
The A/D (Digital/ Analog) input value did not change even after
the D/A (Digital/ Analog) output value changed( copyir( copyir.com com     • Fold timing sensor connector loose, broken, defective • Fold timing sensor defective • Fold timing sensor, mylar covered with paper dust • Mylar disconnected( copyir( copyir.com com
785    Z-fold leading edge sensor adjustment error
The A/D input value did not change even after the D/A output value changed( copyir( copyir.com com     • Leading edge sensor connector loose, broken, defective • Leading edge sensor defective • Leading edge sensor, mylar covered with paper dust • Mylar disconnected( copyir( copyir.com com
786    Z-fold EEPROM error
The write operation to the Z-folding EEPROM failed after 2 attempts    • EEPROM defective
789    Z-fold top tray exit motor error
The motor driver detects an error( copyir( copyir.com com     • Motor overcurrent • Motor driver overheat
790    Finisher staple trimming hopper full
The staple waste hopper is full of cut staples( copyir( copyir.com com     • If the hopper is full, empty the hopper • If the hopper is not full, the hopper full sensor is disconnected, defective
816    Energy save I/O subsystem error
The energy save I/O subsystem is defective or this system detects the controller board error( copyir( copyir.com com     • Reboot the machine( copyir( copyir.com com  • Replace the controller board( copyir( copyir.com com
817    Monitor Error
This is a file detection and electronic file signature check error when the boot loader attempts to read the self-diagnostic module, system kernel, or root system files from the OS Flash ROM, or the items on the SD card in the controller slot are false or corrupted( copyir( copyir.com com     • OS Flash ROM data defective; change the controller firmware • SD card data defective; use another SD card
819    Fatal kernel error
Due to a control error, a RAM overflow occurred during system processing( copyir( copyir.com com  One of the following messages was displayed on the operation panel( copyir( copyir.com com     • System program defective • Controller board defective • Optional board defective • Replace controller firmware
820    Self-diagnostic Error: CPU
0008 Self-diagnostic Error: CPU: System Call Exception
0612 Self-diagnostic Error: CPU: ASIC Interrupt Error    • System program defective • Controller board defective • Optional board defective • Replace controller firmware Note: For more details about this SC code error, execute SP5990 to print an SMC report so you can read the error code( copyir( copyir.com com  The error code is not displayed on the operation panel
821    Self-diagnostic error: ASIC
The Write & Verify check of the ASIC returned an error( copyir( copyir.com com  Note: The main ASIC module on the controller board controls the bus of the ROM device( copyir( copyir.com com     • Replace the controller board
822    Self-diagnostic error: HDD    
823    Self-diagnostic error: NIB    
824    Self-diagnostic error 4: NVRAM
One or more of the following conditions exist: • NVRAM not present( copyir( copyir.com com  • NVRAM damaged • NVRAM socket damaged    • NVRAM defective • Controller board defective • NVRAM backup battery exhausted • NVRAM socket damaged Note: In every case, the controller board must be replaced( copyir( copyir.com com
829    Self-diagnostic Error: Optional RAM
The optional RAM returned an error during the self-diagnostic test( copyir( copyir.com com     • Replace the optional memory board • Controller board defective
833    Self-diagnostic error 8: Engine I/F ASIC    
834    Self-diagnostic error 9: Optional Memory RAM DIMM    
838    Self-diagnostic Error: Clock Generator
A verify error occurred when setting data was read from the clock generator via the I2C bus( copyir( copyir.com com     • Replace the controller board
851    IEEE 1394 I/F error
Driver setting incorrect and cannot be used by the 1394 I/F( copyir( copyir.com com     • NIB (PHY), LINK module defective; change the Interface Board • Controller board defective
853    Wireless LAN Error 1
During machine start-up, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802( copyir( copyir.com com 11b or Bluetooth)( copyir( copyir.com com     • Wireless LAN card missing (was removed)
854    Wireless LAN Error 2
The board that holds the wireless LAN card can be accessed, but the wireless LAN card (802( copyir( copyir.com com 11b/Bluetooth) itself could not be accessed while the machine was operating( copyir( copyir.com com     • Wireless LAN card has been removed( copyir( copyir.com com
855    Wireless LAN Error 3
An error is detected for the wireless LAN card (802( copyir( copyir.com com 11b or Bluetooth)( copyir( copyir.com com     • Wireless LAN card defective • Wireless card connection not tight
856    Wireless LAN Error 4
An error is detected for the wireless LAN board (802( copyir( copyir.com com 11b or Bluetooth)( copyir( copyir.com com     • Wireless LAN card board defective( copyir( copyir.com com  • PCI connector loose (External controller interface board)( copyir( copyir.com com
857    USB I/F Error 1
The USB driver is unstable and generated an error( copyir( copyir.com com  The USB I/F cannot be used( copyir( copyir.com com     • USB board or controller board defective
858    Data Encryption Error 1
These are errors of the HDD Data Encryption Option D377( copyir( copyir.com com     • Replace the controller board
859    Data Encryption Error 2
These are errors of the HDD Data Encryption Option D377( copyir( copyir.com com     
860    HDD startup error at power on
HDD is connected but a driver error is detected( copyir( copyir.com com  The driver does not respond with the status of the HDD within 30 s( copyir( copyir.com com     • HDD is not initialized • Level data is corrupted • HDD is defective
861    HDD Error 2: HDD Startup
The hard disks were detected at power on, but the disks were not detected within 30s after recovery from the energy conservation mode( copyir( copyir.com com     • Cable between the hard disks and controller board disconnected or loose • Hard disk power connector loose • One of the hard disks is defective • Controller defective
862    Bad sector overflow
There more 100 bad sectors in image storage area of the HDD( copyir( copyir.com com     • HDD defective • Format HDD with SP4911-2
863    HDD data read failure
The data written to the HDD cannot be read normally, due to bad sectors generated during operation    • HDD defective Note: If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM, and the next time the HDD is accessed, these bad sectors will not be accessed for read/write operation( copyir( copyir.com com
864    HDD data CRC error
During HDD operation, the HDD cannot respond to a CRC error query( copyir( copyir.com com  Data transfer did not execute normally while data was being written to the HDD( copyir( copyir.com com     • HDD defective
865    HDD access error
HDD responded to an error during operation for a condition other than those for SC863, 864( copyir( copyir.com com     • HDD defective( copyir( copyir.com com
866    SC card error 1: Confirmation
The machine detects an electronic license error in the application on the SD card in the controller slot immediately after the machine is turned on( copyir( copyir.com com  The program on the SD card contains electronic confirmation license data( copyir( copyir.com com  If the program does not contain this license data, or if the result of the check shows that the license data in the program on the SD card is incorrect, then the checked program cannot execute and this SC code is displayed( copyir( copyir.com com     • Program missing from the SD card • Download the correct program for the machine to the SD card
867    SD card error 2: SD card removed
The SD card in the boot slot when the machine was turned on was removed while the machine was on( copyir( copyir.com com     • Insert the SD card, then turn the machine off and on( copyir( copyir.com com
868    SD card error 3: SC card access
An error occurred while an SD card was used( copyir( copyir.com com     • SD card not inserted correctly • SD card defective • Controller board defective Note: If you want to try to reformat the SC card, use SD Formatter Ver 1( copyir( copyir.com com 1( copyir( copyir.com com
870    Address Book Data Error
Address book data stored on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network( copyir( copyir.com com  The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective( copyir( copyir.com com     • Software defective, switch off/on, and change the controller firmware if the problem is not solved( copyir( copyir.com com  • HDD defective Recommended Recovery • Execute SP5846 050 (UCS Settings – Initialize all Directory Info( copyir( copyir.com com ) to initialize all address book data( copyir( copyir.com com  • Initialize the user information with SP5832 006 (HDD Formatting – User Information 1) and SP5832 007 (HDD Formatting – User Information 2) • Replace the HDDs( copyir( copyir.com com  • Boot the machine from the SD card( copyir( copyir.com com
872    HDD mail RX data error
An HDD error was detected immediately after power on( copyir( copyir.com com  The HDD may be defective or the machine was accidentally powered off while the HDD was being accessed( copyir( copyir.com com     • Reformat the HDD with SP5832-7 (Mail RX Data) • Replace the HDD
873    HDD mail send data error
An error was detected on the HDD immediately after the machine was turned on, or power was turned of while the machine used the HDD( copyir( copyir.com com     • Do SP5832-007 (Format HDD – Mail TX Data) to initialize the HDD( copyir( copyir.com com  • Replace the HDD( copyir( copyir.com com
874    Delete All Error 1: HDD
A data error was detected for the HDD/NVRAM after the "Delete All" option was used( copyir( copyir.com com  Note: The source of this error is the Data Overwrite Security Unit running from an SD card( copyir( copyir.com com     • Turn the main switch off/on and try the operation again( copyir( copyir.com com  • Install the Data Overwrite Security Unit again( copyir( copyir.com com  For more, see section "MFP Options" in "Installation"( copyir( copyir.com com  • HDD defective( copyir( copyir.com com
875    Delete All Error 2: Data area
An error occurred while the machine deleted data from the HDD Note: The source of this error is the Data Overwrite Security Unit running from an SD card( copyir( copyir.com com     • Turn the main switch off/on and try the operation again( copyir( copyir.com com
876    Log data abnormal
An error was detected in the handling of the log data at power on or during machine operation( copyir( copyir.com com  This can be caused by switching the machine off while it is operating( copyir( copyir.com com     • Software error( copyir( copyir.com com  Update the firmware • NVRAM defective • HDD defective
877    Data Overwrite Security SD card error
An error occurred, preventing successful execution of the Data Overwrite Security function, even though it has been set up and enabled( copyir( copyir.com com     • DOS card is not inserted completely into the SD card slot • DOS card has been removed from the SD card slot( copyir( copyir.com com  • DOS card is damaged( copyir( copyir.com com  Note: • If the SD card has been removed (or was not installed correctly), switch the machine off, insert the SD card, then switch on the machine again( copyir( copyir.com com  • If the SD card has been damaged, procure a new SD card, replace the NVRAM, then do the DOS option installation( copyir( copyir.com com
878    TPM electronic authentication error
The system hash value registered in TPM and the value registered in USB flash memory are not same during system booting( copyir( copyir.com com     • The system module was updated through the prescribed update root, so the controller board became defective( copyir( copyir.com com  • USB flash memory did not work correctly( copyir( copyir.com com
880    Media Link Board Error
A request for access to the Media Link Board was not answered within the specified time( copyir( copyir.com com     • Media Link Board defective( copyir( copyir.com com
900    Electrical Total Counter Error
The total counter contains data that is not a number( copyir( copyir.com com     • NVRAM disturbed unexpectedly( copyir( copyir.com com  • NVRAM defective NVRAM data corrupted( copyir( copyir.com com
901    Mechanical total counter error
The mechanical counter is not connected( copyir( copyir.com com     • Mechanical total counter defective • Mechanical total counter connector not connected
910    External Controller Error 1    
911    External Controller Error 2    
912    External Controller Error 3    
913    External Controller Error 4    
914    External Controller Error 5    
919    External Controller Error 6
While EAC (External Application Converter), the conversion module, was operating normally, the receipt of a power line interrupt signal from the FLUTE serial driver was detected, of BREAK signal from the other station was detected( copyir( copyir.com com     • Power outage at the EFI controller( copyir( copyir.com com  • EFI controller was rebooted( copyir( copyir.com com  • Connection to EFI controller loose( copyir( copyir.com com
920    Printer Error 1
An internal application error was detected and operation cannot continue( copyir( copyir.com com     • Software defective, switch off/on, or change the controller firmware if the problem is not solved( copyir( copyir.com com  • Insufficient memory
921    Printer Error 2
When the printer application started, the font to use could not be found on the SD card( copyir( copyir.com com     • The font is not on the SD card
925    Net File Function Error    
953    Scanner image setting error
The settings required for image processing using the scanner are not sent from the IPU( copyir( copyir.com com     • Software defective
954    Printer image setting error
The settings required for image processing using the printer controller are not sent from the IPU( copyir( copyir.com com     • Software defective
955    Memory setting error
The settings that are required for image processing using the memory are not sent from the IPU( copyir( copyir.com com     • Software defective
964    Printer ready error
The print ready signal is not generated for more than 17 seconds after the IPU received the print start signal( copyir( copyir.com com     • Software defective
984    Print image data transfer error
After a data transfer begins from the controller to the engine via the PCI bus, the transfer does not end within 15 s( copyir( copyir.com com     • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected
985    Scanned image data transmission error
After a data transfer begins from the engine to the controller via the PCI bus, the transfer does not end within 3 s( copyir( copyir.com com     • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected
986    Software error 1
The write parameter received by the write module at the beginning of the setting table is NULL( copyir( copyir.com com     • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected
990    Software Performance Error 1
An unexpected operation was encountered by the software( copyir( copyir.com com     • Software crash, reboot the machine • If the HDDs have just been replaced, be sure to download the stamp data (SP 5853)( copyir( copyir.com com  • With SP5990 004(SMC Report – Logging Data), print the most recent information for SC990( copyir( copyir.com com  • The SC990 information displays the file name, line number, and value( copyir( copyir.com com  Report this information to your technical supervisor( copyir( copyir.com com  For example: Funciton( copyir( copyir.com com c LINE: 123 VAL: 0
991    Software Error
The software performs an unexpected function and the program cannot continue( copyir( copyir.com com  Recovery processing allows the program to continue( copyir( copyir.com com     • Software defective, re-boot
992    Undefined Error (No SC Code)
An error not controlled by the system occurred (the error does not come under any other SC code)( copyir( copyir.com com     • Software defective • Turn the machine power off and on( copyir( copyir.com com  The machine cannot be used until this error is corrected( copyir( copyir.com com  • Re-install firmware
994    Operation Panel Management Records Exceeded
An error occurred because the number of records exceeded the limit for images managed in the service layer of the firmware( copyir( copyir.com com  This can occur if there are too many application screens open on the operation panel( copyir( copyir.com com     No action required because this SC does not interfere with operation of the machine( copyir( copyir.com com
997    Application Selection Error
An application did not start after pressing the appropriate key on the operation panel( copyir( copyir.com com     • Software bug; change the firmware for the application that failed • A RAM or DIMM option required by the application is not installed or not installed correctly( copyir( copyir.com com
998    Application start error
No applications start within 60 seconds after the power is turned on( copyir( copyir.com com     • Loose connection of RAM-DIMM, ROM-DIMM • Defective controller • Software problem

خواندن 1065 دفعه

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب