Your browser does not support JavaScript! > ریکوآفشیوRicoh Aficio MPC305SPF
(0) محصول
چهارشنبه, 21 بهمن 1394 18:05

ریکوآفشیوRicoh Aficio MPC305SPF

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات ریکو براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

 

 

101    Exposure lamp error
The peak white level is less than 64/255 digits (8 bits) when scanning the shading plate ( copyir ( copyir.com com     Exposure lamp defective ( copyir ( copyir.com com  Lamp stabilizer defective ( copyir ( copyir.com com  Exposure lamp connector defective ( copyir ( copyir.com com  Standard white plate dirty ( copyir ( copyir.com com  Scanner mirror or scanner lens out of position or dirty ( copyir ( copyir.com com
120    Scanner home position error 1
The scanner home position sensor does not detect the "OFF" condition during operation ( copyir ( copyir.com com     Scanner motor driver defective Scanner motor defective Harness between SBU and scanner motor disconnected Scanner HP sensor defective Harness between SBU and HP sensor disconnected
121    Scanner home position error 2
The scanner home position sensor does not detect the "ON" condition during operation ( copyir ( copyir.com com     Scanner motor driver defective Scanner motor defective Harness between SBU and scanner motor disconnected Scanner HP sensor defective Harness between SBU and HP sensor disconnected
141    Black level detection error
The black level cannot be adjusted within the target value during the zero clamp ( copyir ( copyir.com com     Harness disconnected ( copyir ( copyir.com com  Defective SBU
142    White level detection error
The white level cannot be adjusted within the target during auto gain control ( copyir ( copyir.com com     Dirty exposure glass or optics section SBU defective Exposure lamp defective Lamp stabilizer defective Scanner motor defective
144    SBU communication error
The SBU connection cannot be detected at power on or recovery from the energy save mode, or a signal is abnormal ( copyir ( copyir.com com     Defective SBU ( copyir ( copyir.com com  Defective harness ( copyir ( copyir.com com  Defective detection port on the BICU ( copyir ( copyir.com com
161-01    BICU error: abnormal LSYNC
The error result of the self-diagnostic by the ASIC on the BICU is detected at power on or recovery from the energy save mode ( copyir ( copyir.com com     Defective BICU ( copyir ( copyir.com com  Defective connection between BICU and SBU ( copyir ( copyir.com com
162-01    BICU error: PCIE communication error
The link up interrupt from LYRA is not detected or the number of connection lanes is other than 2 at power on or recovery from the energy save mode ( copyir ( copyir.com com     Defective BICU ( copyir ( copyir.com com  Defective connection between BICU and SBU
165    Copy Data Security Unit error
The copy data security board is not detected or a device check error occurs when the copy data security function is set "ON" with the initial setting ( copyir ( copyir.com com     Incorrect installation of the copy data security board ( copyir ( copyir.com com  Defective copy data security board
195    Serial Number Mismatch
Serial number stored in the memory does not have the correct code ( copyir ( copyir.com com     EEPROM defective ( copyir ( copyir.com com  BICU replaced without original EEPROM
202-01    Polygon motor error 1: ON timeout: Bk, Cy
The polygon mirror motor does not reach the targeted operating speed within the specified time after turning on or changing speed    Defective or disconnected harness to polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor
202-03    Polygon motor error 1: ON timeout: Ma, Ye
The polygon mirror motor does not reach the targeted operating speed within the specified time after turning on or changing speed    Defective or disconnected harness to polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor
202-03    Polygon motor error 2: OFF timeout: Ma, Ye
The polygon mirror motor does not leave the READY status within the given time after the polygon motor switches off ( copyir ( copyir.com com     Disconnected or defective harness to polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor
203-01    Polygon motor error 2: OFF timeout: Bk, Cy
The polygon mirror motor does not leave the READY status within the given time after the polygon motor switches off ( copyir ( copyir.com com     Disconnected or defective harness to polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor
204-01    Polygon motor error 0: XSCRDY signal error: Bk, Cy
The SCRDY_N signal goes HIGH (inactive) during a writing operation ( copyir ( copyir.com com     Disconnected or defective harness to polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor ( copyir ( copyir.com com  Defective polygon motor driver board
204-03    Polygon motor error 1: XSCRDY signal error: Ma, Ye
The SCRDY_N signal goes HIGH (inactive) during a writing operation ( copyir ( copyir.com com     Disconnected or defective harness to polygon motor driver board ( copyir ( copyir.com com  Defective polygon motor ( copyir ( copyir.com com  Defective polygon motor driver board
220-01    Laser synchronizing detection error: start position LD1: Bk
The laser synchronizing detection signal for the start position of the LDB is not output for the prescribed time after the LDB unit turns on while the polygon motor is rotating normally    Broken I/F harness of synchronizing detection unit ( copyir ( copyir.com com  Defective synchronizing detection board ( copyir ( copyir.com com  Defective LDB ( copyir ( copyir.com com  Defective BICU
220-02    Laser synchronizing detection error: start position LD1: Ma
The laser synchronizing detection signal for the start position of the LDB is not output for the prescribed time after the LDB unit turns on while the polygon motor is rotating normally    Broken I/F harness of synchronizing detection unit ( copyir ( copyir.com com  Defective synchronizing detection board ( copyir ( copyir.com com  Defective LDB ( copyir ( copyir.com com  Defective BICU
230-01    FGATE ON error: Bk
The PFGATE ON signal does not assert within 5 seconds after processing start timing for black (-01), cyan (-02), magenta (-03) or yellow (-04) color writing ( copyir ( copyir.com com     Defective ASIC (Lupus) ( copyir ( copyir.com com  Poor connection between controller and BICU ( copyir ( copyir.com com  Defective BICU
230-02    FGATE ON error: Cy
The PFGATE ON signal does not assert within 5 seconds after processing start timing for black (-01), cyan (-02), magenta (-03) or yellow (-04) color writing ( copyir ( copyir.com com     Defective ASIC (Lupus) ( copyir ( copyir.com com  Poor connection between controller and BICU ( copyir ( copyir.com com  Defective BICU
230-03    FGATE ON error: Ma
The PFGATE ON signal does not assert within 5 seconds after processing start timing for black (-01), cyan (-02), magenta (-03) or yellow (-04) color writing ( copyir ( copyir.com com     Defective ASIC (Lupus) ( copyir ( copyir.com com  Poor connection between controller and BICU ( copyir ( copyir.com com  Defective BICU
230-04    FGATE ON error: Ye
The PFGATE ON signal does not assert within 5 seconds after processing start timing for black (-01), cyan (-02), magenta (-03) or yellow (-04) color writing ( copyir ( copyir.com com     Defective ASIC (Lupus) ( copyir ( copyir.com com  Poor connection between controller and BICU ( copyir ( copyir.com com  Defective BICU
231-01    FGATE OFF error: Bk
The PFGATE ON signal still asserts within 5 seconds after processing finish timing for black (-01), cyan (-02), magenta (-03) or yellow (-04) color writing ( copyir ( copyir.com com  The PFGATE ON signal still asserts when the next job starts ( copyir ( copyir.com com     Defective ASIC (Lupus) ( copyir ( copyir.com com  Poor connection between controller and BICU ( copyir ( copyir.com com  Defective BICU
231-02    FGATE OFF error: Cy
The PFGATE ON signal still asserts within 5 seconds after processing finish timing for black (-01), cyan (-02), magenta (-03) or yellow (-04) color writing ( copyir ( copyir.com com  The PFGATE ON signal still asserts when the next job starts ( copyir ( copyir.com com     Defective ASIC (Lupus) ( copyir ( copyir.com com  Poor connection between controller and BICU ( copyir ( copyir.com com  Defective BICU
231-03    FGATE OFF error: Ma
The PFGATE ON signal still asserts within 5 seconds after processing finish timing for black (-01), cyan (-02), magenta (-03) or yellow (-04) color writing ( copyir ( copyir.com com  The PFGATE ON signal still asserts when the next job starts ( copyir ( copyir.com com     Defective ASIC (Lupus) ( copyir ( copyir.com com  Poor connection between controller and BICU ( copyir ( copyir.com com  Defective BICU
231-04    FGATE OFF error: Ye
The PFGATE ON signal still asserts within 5 seconds after processing finish timing for black (-01), cyan (-02), magenta (-03) or yellow (-04) color writing ( copyir ( copyir.com com  The PFGATE ON signal still asserts when the next job starts ( copyir ( copyir.com com     Defective ASIC (Lupus) ( copyir ( copyir.com com  Poor connection between controller and BICU ( copyir ( copyir.com com  Defective BICU
240-01    LD error: Bk or Cy
The BICU detects an LD error a few times consecutively when the LDB unit turns on after LDB initialization ( copyir ( copyir.com com     Worn-out LD ( copyir ( copyir.com com  Disconnected or broken harness of the LD
240-03    LD error: Ma or Ye
The BICU detects an LD error a few times consecutively when the LDB unit turns on after LDB initialization ( copyir ( copyir.com com     Worn-out LD ( copyir ( copyir.com com  Disconnected or broken harness of the LD
260-01    Writing temperature thermistor error: Bk - Cy
The temperature thermistor output is no more than 0 ( copyir ( copyir.com com 81 V or no less than 2 ( copyir ( copyir.com com 95 V ( copyir ( copyir.com com     No thermistor is installed or disconnected connectors ( copyir ( copyir.com com  Defective thermistor
260-03    Writing temperature thermistor error: Ma - Ye
The temperature thermistor output is no more than 0 ( copyir ( copyir.com com 81 V or no less than 2 ( copyir ( copyir.com com 95 V ( copyir ( copyir.com com     No thermistor is installed or disconnected connectors ( copyir ( copyir.com com  Defective thermistor
285    MUSIC error
Line position adjustment fails four consecutive times ( copyir ( copyir.com com     Pattern sampling error (insufficient image density) ( copyir ( copyir.com com  Defective TM sensors ( copyir ( copyir.com com  Defective image transfer belt unit ( copyir ( copyir.com com  Defective PCDU(s) ( copyir ( copyir.com com  Defective laser optics housing unit ( copyir ( copyir.com com
312    Charge P ( copyir ( copyir.com com P ( copyir ( copyir.com com  output error: Bk
The feedback voltage of the charge AC for each color is 0 ( copyir ( copyir.com com 3 V or less for 0 ( copyir ( copyir.com com 2 seconds after the charge AC has turned on ( copyir ( copyir.com com     Disconnected or broken harnesses of the HVPS ( copyir ( copyir.com com  Defective PCDU ( copyir ( copyir.com com  Defective HVPS ( copyir ( copyir.com com
313    Charge P ( copyir ( copyir.com com P ( copyir ( copyir.com com  output error: Cy
The feedback voltage of the charge AC for each color is 0 ( copyir ( copyir.com com 3 V or less for 0 ( copyir ( copyir.com com 2 seconds after the charge AC has turned on ( copyir ( copyir.com com     Disconnected or broken harnesses of the HVPS ( copyir ( copyir.com com  Defective PCDU ( copyir ( copyir.com com  Defective HVPS ( copyir ( copyir.com com
314    Charge P ( copyir ( copyir.com com P ( copyir ( copyir.com com  output error: Ma
The feedback voltage of the charge AC for each color is 0 ( copyir ( copyir.com com 3 V or less for 0 ( copyir ( copyir.com com 2 seconds after the charge AC has turned on ( copyir ( copyir.com com     Disconnected or broken harnesses of the HVPS ( copyir ( copyir.com com  Defective PCDU ( copyir ( copyir.com com  Defective HVPS ( copyir ( copyir.com com
315    Charge P ( copyir ( copyir.com com P ( copyir ( copyir.com com  output error: Ye
The feedback voltage of the charge AC for each color is 0 ( copyir ( copyir.com com 3 V or less for 0 ( copyir ( copyir.com com 2 seconds after the charge AC has turned on ( copyir ( copyir.com com     Disconnected or broken harnesses of the HVPS ( copyir ( copyir.com com  Defective PCDU ( copyir ( copyir.com com  Defective HVPS ( copyir ( copyir.com com
325    Color development motor error
The motor LOCK signal is not detected for more than two seconds while the motor START signal is on ( copyir ( copyir.com com     Color development motor slip due to an increase in the torque caused by connected components ( copyir ( copyir.com com  Defective motor
360-01    TD sensor (Vt high) error 1: Bk The Vt value of the black TD sensor exceeds the specified value (SP3030-031)+-0 ( copyir ( copyir.com com 2 V for three consecutive times ( copyir ( copyir.com com     Black, magenta, cyan, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
360-02    TD sensor (Vt high) error 1: Cy The Vt value of the cyan TD sensor exceeds the specified value (SP3030-032)+-0 ( copyir ( copyir.com com 2 V for three consecutive times ( copyir ( copyir.com com     Black, magenta, cyan, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
360-03    TD sensor (Vt high) error 1: Ma The Vt value of the magenta TD sensor exceeds the specified value (SP3030-033)+-0 ( copyir ( copyir.com com 2 V for three consecutive times ( copyir ( copyir.com com     Black, magenta, cyan, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
360-04    TD sensor (Vt high) error 1: Ye The Vt value of the yellow TD sensor exceeds the specified value (SP3030-034)+-0 ( copyir ( copyir.com com 2 V for three consecutive times ( copyir ( copyir.com com     Black, magenta, cyan, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
361-01    TD sensor (Vt) upper limit error: Bk
The Vt value upper limit of the black TD sensor (SP3210-001) exceeds the specified value (SP3211-002) for the specified number of times (SP3211-003) consecutively ( copyir ( copyir.com com     Black, cyan, magenta, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
361-02    TD sensor (Vt) upper limit error 1: Cy
The Vt value upper limit of the cyan TD sensor (SP3210-002) exceeds the specified value (SP3211-002) for the specified number of times (SP3211-003) consecutively ( copyir ( copyir.com com     Black, cyan, magenta, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
361-03    TD sensor (Vt) upper limit error 1: Ma
The Vt value upper limit of the magenta TD sensor (SP3210-003) exceeds the specified value (SP3211-002) for the specified number of times (SP3211-003) consecutively ( copyir ( copyir.com com     Black, cyan, magenta, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
361-04    TD sensor (Vt) upper limit error 1: Ye
The Vt value upper limit of the yellow TD sensor (SP3210-004) exceeds the specified value (SP3211-002) for the specified number of times (SP3211-003) consecutively ( copyir ( copyir.com com     Black, cyan, magenta, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
362-01    TD sensor (Vt) lower limit error: Bk
The Vt value lower limit of the black TD sensor (SP3210-001) falls below the specified value (SP3211-004) for the specified number of times (SP3211-005) consecutively ( copyir ( copyir.com com     Black, cyan, magenta, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
362-02    TD sensor (Vt) lower limit error 1: Cy
The Vt value lower limit of the cyan TD sensor (SP3210-002) falls below the specified value (SP3211-004) for the specified number of times (SP3211-005) consecutively ( copyir ( copyir.com com     Black, cyan, magenta, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
362-03    TD sensor (Vt) lower limit error 1: Ma
The Vt value lower limit of the magenta TD sensor (SP3210-003) falls below the specified value (SP3211-004) for the specified number of times (SP3211-005) consecutively ( copyir ( copyir.com com     Black, cyan, magenta, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
362-04    TD sensor (Vt) lower limit error 1: Ye
The Vt value lower limit of the yellow TD sensor (SP3210-004) falls below the specified value (SP3211-004) for the specified number of times (SP3211-005) consecutively ( copyir ( copyir.com com     Black, cyan, magenta, or yellow TD sensor disconnected ( copyir ( copyir.com com  Harness between TD sensor and PCDU defective ( copyir ( copyir.com com  Defective TD sensor
370    ID sensor calibration error
The reflection light output voltage of the ID sensor (Vsg_reg) is not adjusted within the target range ( copyir ( copyir.com com  Upper limit: SP3320-013 (default: 4 ( copyir ( copyir.com com 5 V) Lower limit: SP3320-014 (default: 3 ( copyir ( copyir.com com 5 V)    Disconnected ID sensor connectors ( copyir ( copyir.com com  Dirty or defective ID sensor ( copyir ( copyir.com com  Defective image transfer belt
372    TD sensor adjustment error: Bk
During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the value specified with SP3238-001 to -004 (default: 2 ( copyir ( copyir.com com 5V) +- ( copyir ( copyir.com com 2 V ( copyir ( copyir.com com     Heat seal not removed from a new developer pack ( copyir ( copyir.com com  TD harness sensor disconnected, loose or defective ( copyir ( copyir.com com  TD sensor defective ( copyir ( copyir.com com  Harness between TD sensor and drawer disconnected, defective ( copyir ( copyir.com com
373    TD sensor adjustment error: Ma
During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the value specified with SP3238-001 to -004 (default: 2 ( copyir ( copyir.com com 5V) +- ( copyir ( copyir.com com 2 V ( copyir ( copyir.com com     Heat seal not removed from a new developer pack ( copyir ( copyir.com com  TD harness sensor disconnected, loose or defective ( copyir ( copyir.com com  TD sensor defective ( copyir ( copyir.com com  Harness between TD sensor and drawer disconnected, defective ( copyir ( copyir.com com
374    TD sensor adjustment error: Cy
During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the value specified with SP3238-001 to -004 (default: 2 ( copyir ( copyir.com com 5V) +- ( copyir ( copyir.com com 2 V ( copyir ( copyir.com com     Heat seal not removed from a new developer pack ( copyir ( copyir.com com  TD harness sensor disconnected, loose or defective ( copyir ( copyir.com com  TD sensor defective ( copyir ( copyir.com com  Harness between TD sensor and drawer disconnected, defective ( copyir ( copyir.com com
375    TD sensor adjustment error: Ye
During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the value specified with SP3238-001 to -004 (default: 2 ( copyir ( copyir.com com 5V) +- ( copyir ( copyir.com com 2 V ( copyir ( copyir.com com     Heat seal not removed from a new developer pack ( copyir ( copyir.com com  TD harness sensor disconnected, loose or defective ( copyir ( copyir.com com  TD sensor defective ( copyir ( copyir.com com  Harness between TD sensor and drawer disconnected, defective ( copyir ( copyir.com com
396    Drum/Development motor error: Bk
The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on ( copyir ( copyir.com com     Overload on the drum/development motor ( copyir ( copyir.com com  Defective drum/development motor ( copyir ( copyir.com com  Defective harness ( copyir ( copyir.com com  Shorted 24 V fuse on the PSU ( copyir ( copyir.com com  Defective interlock system ( copyir ( copyir.com com
397    Drum/Development motor error: Cy, Ma, Ye
The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on ( copyir ( copyir.com com     Overload on the drum/development motor ( copyir ( copyir.com com  Defective drum/development motor ( copyir ( copyir.com com  Defective harness ( copyir ( copyir.com com  Shorted 24 V fuse on the PSU ( copyir ( copyir.com com  Defective interlock system ( copyir ( copyir.com com
442    Image transfer belt contact motor error
The image transfer belt contact motor drives beyond the specified time during home position detection or contact operation ( copyir ( copyir.com com     Broken harness or defective connectors ( copyir ( copyir.com com  Disconnected connector of image transfer belt contact sensor or motor ( copyir ( copyir.com com  Defective image transfer belt contact motor ( copyir ( copyir.com com  Image transfer belt unit not installed ( copyir ( copyir.com com
452    Paper transfer belt contact motor error
The paper transfer belt contact motor drives beyond the specified time during home position detection or contact operation ( copyir ( copyir.com com     Broken harness or defective connectors ( copyir ( copyir.com com  Disconnected connector of paper transfer belt contact sensor or motor ( copyir ( copyir.com com  Defective paper transfer belt contact motor ( copyir ( copyir.com com  Paper transfer belt unit not installed ( copyir ( copyir.com com
460    Separation power pack output error
An interrupt checks the status of the power pack every 20 ms ( copyir ( copyir.com com  This SC is issued if the BICU detects a short in the power pack 10 times at D(ac) ( copyir ( copyir.com com     High voltage leak ( copyir ( copyir.com com  Broken harness ( copyir ( copyir.com com  Defective image transfer belt unit or paper transfer unit ( copyir ( copyir.com com  Defective high voltage supply unitr belt ( copyir ( copyir.com com
491    High voltage power: Drum/ development bias output error
An error signal is detected for 0 ( copyir ( copyir.com com 2 seconds when charging the drum or development ( copyir ( copyir.com com     High voltage leak ( copyir ( copyir.com com  Broken harness ( copyir ( copyir.com com  Defective drum unit or development unit ( copyir ( copyir.com com  Defective high voltage supply unit ( copyir ( copyir.com com
492    High voltage power: Image transfer/ paper transfer bias output error
An error signal is detected for 200 ms when charging the separation, image transfer belt or paper transfer roller ( copyir ( copyir.com com     High voltage leak ( copyir ( copyir.com com  Broken harness ( copyir ( copyir.com com  Defective image transfer belt unit or paper transfer unit ( copyir ( copyir.com com  Defective high voltage supply unit ( copyir ( copyir.com com
497    Image creation temperature sensor error 1
The thermistor output of the temperature sensor is not within the prescribed range (more than 0 ( copyir ( copyir.com com 5 V to less than 3 ( copyir ( copyir.com com 0 V) for three consecutive times ( copyir ( copyir.com com     
498    Temperature and humidity sensor error
The thermistor output of the temperature sensor was not within the prescribed range (more than 0 ( copyir ( copyir.com com 76V to less than 2 ( copyir ( copyir.com com 90V) ( copyir ( copyir.com com  The thermistor output of the humidity sensor was not within the prescribed range (2 ( copyir ( copyir.com com 4V or more) ( copyir ( copyir.com com     Temperature and humidity sensor harness disconnected, loose, defective ( copyir ( copyir.com com  Temperature and humidity sensor defective ( copyir ( copyir.com com
501    1st paper tray lift motor malfunction
The paper lift sensor does not detect paper or finish the detection within the specified time, after the tray lift motor switched on ( copyir ( copyir.com com     An obstruction (jammed paper, paper scraps, etc ( copyir ( copyir.com com ) has blocked the motor drive and caused an overload ( copyir ( copyir.com com  Paper lift sensor connection loose, disconnected, or damaged Paper lift sensor defective Tray lift motor connection loose, disconnected, or damaged Tray lift motor defective
502    2nd paper tray lift motor malfunction (optional paper feed unit)
The paper lift sensor does not detect paper or finish the detection within the specified time, after the tray lift motor switched on ( copyir ( copyir.com com     An obstruction (jammed paper, paper scraps, etc ( copyir ( copyir.com com ) has blocked the motor drive and caused an overload ( copyir ( copyir.com com  Paper lift sensor connection loose, disconnected, or damaged Paper lift sensor defective Tray lift motor connection loose, disconnected, or damaged Tray lift motor defective
503    3rd paper tray lift motor malfunction (optional paper feed unit)
The paper lift sensor does not detect paper or finish the detection within the specified time, after the tray lift motor switched on ( copyir ( copyir.com com     An obstruction (jammed paper, paper scraps, etc ( copyir ( copyir.com com ) has blocked the motor drive and caused an overload ( copyir ( copyir.com com  Paper lift sensor connection loose, disconnected, or damaged Paper lift sensor defective Tray lift motor connection loose, disconnected, or damaged Tray lift motor defective
508    By-pass bottom plate error
The signal from the by-pass tray HP sensor does not change for 2 seconds after the by-pass bottom plate clutch was activated ( copyir ( copyir.com com  If this condition occurs three consecutive times, this SC is generated ( copyir ( copyir.com com     Disconnected or defective connectors of the by-pass bottom plate clutch ( copyir ( copyir.com com  Disconnected or defective by-pass HP sensor ( copyir ( copyir.com com  Defective by-pass bottom plate detection filler
524    Transport motor error
The machine detects a High signal from a transport motor lock detection for 2 seconds after the transport motor turned on ( copyir ( copyir.com com     Unit overload ( copyir ( copyir.com com  Defective motor ( copyir ( copyir.com com
525    Transport motor error: bank 1
The machine detects a Lock signal from a bank 1 transport motor after the motor turned on ( copyir ( copyir.com com     Motor overload ( copyir ( copyir.com com  Defective motor ( copyir ( copyir.com com  Disconnected connectors ( copyir ( copyir.com com  Broken harness ( copyir ( copyir.com com
526    Transport motor error: bank 2
The machine detects a Lock signal from a bank 2 transport motor after the motor turned on ( copyir ( copyir.com com     Motor overload ( copyir ( copyir.com com  Defective motor ( copyir ( copyir.com com  Disconnected connectors ( copyir ( copyir.com com  Broken harness ( copyir ( copyir.com com
530    Fusing heater exhaust fan motor error
The motor lock signal error is detected 50 consecutive times (5 seconds) after the motor lock signal was first detected ( copyir ( copyir.com com     Defective fan motor ( copyir ( copyir.com com  Disconnected or defective harness ( copyir ( copyir.com com  Defective BICU
531    Development cooling fan motor error
The motor lock signal error is detected 50 consecutive times (5 seconds) after the motor lock signal was first detected ( copyir ( copyir.com com     Defective fan motor ( copyir ( copyir.com com  Disconnected or defective harness ( copyir ( copyir.com com  Defective BICU
532    Writing cooling fan motor error
The motor lock signal error is detected 50 consecutive times (5 seconds) after the motor lock signal was first detected ( copyir ( copyir.com com     Defective fan motor ( copyir ( copyir.com com  Disconnected or defective harness ( copyir ( copyir.com com  Defective BICU
533    PSU fan motor error
The motor lock signal error is detected 50 consecutive times (5 seconds) after the motor lock signal was first detected ( copyir ( copyir.com com     Defective fan motor ( copyir ( copyir.com com  Disconnected or defective harness ( copyir ( copyir.com com  Defective BICU
540    Fusing motor error
The machine detects a High signal from the fusing motor 20 consecutive times after the motor turned on ( copyir ( copyir.com com     Motor overload ( copyir ( copyir.com com  Defective fusing motor ( copyir ( copyir.com com  Shorted +24 fuse on the PSU ( copyir ( copyir.com com
541    Heating roller thermopile error
The temperature detected by the heating roller thermopile does not reach 0°C within the prescribed time for 10 consecutive times ( copyir ( copyir.com com     Loose connection of the heating roller thermopile ( copyir ( copyir.com com  Defective heating roller thermopile ( copyir ( copyir.com com  Defective thermopilee ( copyir ( copyir.com com
542-02, 542-03    Heating roller thermopile reload error ( copyir ( copyir.com com  The heating roller temperature does not reach 80C within the prescribed time ( copyir ( copyir.com com  The center temperature of the heating roller does not reach the target reload permit temperature within the prescribed time ( copyir ( copyir.com com  The center temperature of the heating roller does not reach the target temperature after starting the heater control in warm up with low temperature ( copyir ( copyir.com com     Dirty or defective thermopile lenses ( copyir ( copyir.com com  Defective thermistor ( copyir ( copyir.com com  Input voltage out of specification (out of warranty) ( copyir ( copyir.com com
543    Heating roller thermopile overheat (software error)
The temperature detected by the heating roller thermopile stays at the prescribed temperature within the prescribed time ( copyir ( copyir.com com     Defective PSU ( copyir ( copyir.com com  Defective BICU ( copyir ( copyir.com com
544    Heating roller thermopile overheat (hardware error)
The temperature detected by the heating roller thermopile reaches the prescribed temperature ( copyir ( copyir.com com     Defective BICU ( copyir ( copyir.com com  Defective fusing control system ( copyir ( copyir.com com
545    Heating roller fusing lamp consecutive full power
When the fusing unit is not running in the ready condition, the heating roller fusing lamp keeps on full power for the prescribed time ( copyir ( copyir.com com     Defective thermistor ( copyir ( copyir.com com  Broken heater ( copyir ( copyir.com com
547-01    Zero cross error: fusing lamp relay contact welding
The zero cross signal is detected three times even though the heater relay is off when turning on the main power ( copyir ( copyir.com com  The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door ( copyir ( copyir.com com  The detection error occurs twice or more in 11 zero cross signal detections ( copyir ( copyir.com com  This error is defined when the detected number of zero cross signals is less than 45 ( copyir ( copyir.com com     Defective fusing lamp relay (welded contacts) ( copyir ( copyir.com com  Defective fusing lamp relay circuit ( copyir ( copyir.com com
547-02    Zero cross error: fusing lamp relay contact defective
The zero cross signal is detected three times even though the heater relay is off when turning on the main power ( copyir ( copyir.com com  The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door ( copyir ( copyir.com com  The detection error occurs twice or more in 11 zero cross signal detections ( copyir ( copyir.com com  This error is defined when the detected number of zero cross signals is less than 45 ( copyir ( copyir.com com     Defective fusing lamp relay (open contact) ( copyir ( copyir.com com  Defective fusing lamp relay circuit ( copyir ( copyir.com com
547-03    Zero cross error: low frequencies error
The zero cross signal is detected three times even though the heater relay is off when turning on the main power ( copyir ( copyir.com com  The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door ( copyir ( copyir.com com  The detection error occurs twice or more in the 11 zero cross signal detections ( copyir ( copyir.com com  This error is defined when the detected number of zero cross signals is less than 45 ( copyir ( copyir.com com     Unstable frequencies from utility power line ( copyir ( copyir.com com  Defective fusing lamp relay circuit ( copyir ( copyir.com com  Unstable power supply ( copyir ( copyir.com com
551    Heating roller thermistor error
The temperature at the end of the heating roller measured by the heating roller thermistor does not exceed -11°C or -41°C for the prescribed time ( copyir ( copyir.com com     Broken thermopile or thermistor ( copyir ( copyir.com com  Defective connectors ( copyir ( copyir.com com
552-03    Heating roller warm-up error (sensor 2)
The heating roller temperature does not reach 80?XC within the prescribed time ( copyir ( copyir.com com  The center temperature of the heating roller does not reach the target reload permit temperature within the prescribed time ( copyir ( copyir.com com  The center temperature of the heating roller does not reach the target reload permit pressure within the prescribed time ( copyir ( copyir.com com     Dirty thermopile lenses ( copyir ( copyir.com com  Defective heating roller thermistor ( copyir ( copyir.com com  Input voltage out of the warranty (out of specification) ( copyir ( copyir.com com
554    Heating roller fusing lamp overheat (hardware error)
The temperature detected by the heating roller thermistor reaches the prescribed temperature ( copyir ( copyir.com com     Defective BICU ( copyir ( copyir.com com  Defective fusing control system
557    Zero cross frequency error
When the zero cross signal is 66 or more and it is detected 10 times or more in 11 detections, the machine determines that input 60 Hz and this SC occurs ( copyir ( copyir.com com     Noise (High frequency) ( copyir ( copyir.com com  Defective PSU ( copyir ( copyir.com com
559    Consecutive fusing jam
The paper jam counter for the fusing unit reaches three consecutive times (the fusing exit sensor does not detect the paper) ( copyir ( copyir.com com     Paper jam in the fusing unit ( copyir ( copyir.com com
561    Pressure roller thermistor error: Center
The temperature detected by the pressure roller thermistor does not reach 0 °C within the prescribed time ( copyir ( copyir.com com     Loose connection of the pressure roller thermistor ( copyir ( copyir.com com  Defective thermopile ( copyir ( copyir.com com  Defective pressure roller thermistor
562-03    Heating roller warm-up error (sensor 3)
The center temperature of the heating roller does not reach the target reload permit pressure within the prescribed time ( copyir ( copyir.com com     Dirty thermopile lenses ( copyir ( copyir.com com  Defective heating roller thermistor ( copyir ( copyir.com com  Input voltage out of the warranty (out of specification) ( copyir ( copyir.com com
563    Pressure roller overheat (software error): Center
The temperature detected by the pressure roller thermistor stays at the prescribed temperature within the prescribed time ( copyir ( copyir.com com     Defective PSU ( copyir ( copyir.com com  Defective BICU
564    Pressure roller overheat (hardware error): Center
The temperature detected by the pressure roller thermistor detects prescribed temperature ( copyir ( copyir.com com     Defective BICU ( copyir ( copyir.com com  Defective fusing control system ( copyir ( copyir.com com
571    Pressure roller thermistor error: End
The temperature detected by the pressure roller thermistor does not reach 0 °C within the prescribed time ( copyir ( copyir.com com     Loose connection of the pressure roller thermistor ( copyir ( copyir.com com  Defective thermopile ( copyir ( copyir.com com  Defective pressure roller thermistor ( copyir ( copyir.com com
572-03    Heating roller warm-up error (sensor 4)
The temperature of the heating roller does not reach 20 °C within the prescribed time ( copyir ( copyir.com com     Dirty thermopile lenses ( copyir ( copyir.com com  Defective heating roller thermistor ( copyir ( copyir.com com  Input voltage out of the warranty (out of specification) ( copyir ( copyir.com com
573    Pressure roller overheat (software error): End
The temperature detected by the pressure roller thermistor stays at the prescribed temperature within the prescribed time ( copyir ( copyir.com com     Defective PSU ( copyir ( copyir.com com  Defective BICU
574    Pressure roller overheat (hardware error): End
The temperature detected by the pressure roller thermistor detects prescribed temperature ( copyir ( copyir.com com     Defective BICU ( copyir ( copyir.com com  Defective fusing control system
610    Mechanical counter error: Bk
This SC is only for NA models ( copyir ( copyir.com com  The machine detects the mechanical counter error when SP5987-001 is set to "1" ( copyir ( copyir.com com     Disconnected mechanical counter ( copyir ( copyir.com com  Defective mechanical counter ( copyir ( copyir.com com
622    Paper tray unit communication error
While the BICU communicates with an optional unit, an SC code is displayed if one of following conditions occurs ( copyir ( copyir.com com  „X The IPU receives the break signal which is generated by the peripherals only just after the main switch is turned on ( copyir ( copyir.com com  „X When the BCU does not receive an OK signal from a peripheral 100ms after sending a command to it ( copyir ( copyir.com com  The IPU resends the command ( copyir ( copyir.com com  The IPU does not receive an OK signal after sending the command 3 times ( copyir ( copyir.com com     Cable problems ( copyir ( copyir.com com  BICU problems ( copyir ( copyir.com com  PSU problems in the machine ( copyir ( copyir.com com  Main board problems in the peripherals ( copyir ( copyir.com com
623    2nd Paper Bank communication error
This SC is not issued for this machine ( copyir ( copyir.com com  When a communication error signal between the 1st paper bank and 2nd paper bank is received ( copyir ( copyir.com com     Loose or disconnected connector
632    Counter device error 1
After 3 attempts to send a data frame to the optional counter device via the serial communication line, no ACK signal was received within 100 ms ( copyir ( copyir.com com     Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged ( copyir ( copyir.com com  Make sure that SP5113 is set to enable the optional counter device ( copyir ( copyir.com com
633    Counter device error 2
After communication is established, the controller receives the brake signal from the accounting device ( copyir ( copyir.com com     Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged ( copyir ( copyir.com com  Make sure that SP5113 is set to enable the optional counter device ( copyir ( copyir.com com
634    Counter device error 3
A backup RAM error was returned by the counter device ( copyir ( copyir.com com     Counter device control board defective ( copyir ( copyir.com com  Backup battery of counter device defective ( copyir ( copyir.com com
635    Counter device error 4
A backup battery error was returned by the counter device ( copyir ( copyir.com com     Counter device control board defective ( copyir ( copyir.com com  Backup battery of counter device defective ( copyir ( copyir.com com
636    SD Card Error    
637-01    Tracking information notice error    The machine failed to give notice of the tracking information to the tracking SDK application ( copyir ( copyir.com com  Tracking information is lost, and the machine cannot count correctly ( copyir ( copyir.com com
637-02    Management server error
Tracking information is lost ( copyir ( copyir.com com     The machine failed to give notice of the tracking information to the management server ( copyir ( copyir.com com  Tracking information is lost, and the machine cannot count correctly ( copyir ( copyir.com com
640    Communication error: Engine Controller (Check sum error)    Hardware error with PCI
641    Communication error: Engine Controller (No response)
No response from engine to frame after frame sending from controller with RAPI protocol ( copyir ( copyir.com com  (No response after 3 attempts of sending every 100 ms)    Asserts the error detected by the serial driver from PSC module to SRM with RAPI command ( copyir ( copyir.com com
641    Engine Serial Communication error
An error occurs during serial communication with the engine ( copyir ( copyir.com com     
669    EEPROM error
Retry of EEPROM communication fails three times after the machine has detected the EEPROM error ( copyir ( copyir.com com     Caused by noise
670    Engine start up error
The BICU fails to respond within the prescribed time when the machine is turned on ( copyir ( copyir.com com     Connections between BICU and controller board are loose, disconnected, or damaged ( copyir ( copyir.com com
672    Controller start up error
After the machine is powered on, the communication between the controller and the operation panel is not established, or communication with the controller is interrupted after a normal startup ( copyir ( copyir.com com  After startup reset of the operation panel, the attention code (FDH) or the attention acknowledge code (FEH) is not sent from the controller within 30 seconds ( copyir ( copyir.com com  After the controller issues a command to check the communication line 687with the controller at 30-second intervals, the controller fails to respond twice ( copyir ( copyir.com com     Controller stalled ( copyir ( copyir.com com  Controller board installed incorrectly ( copyir ( copyir.com com  Controller board defective ( copyir ( copyir.com com  Operation panel connector loose or defective ( copyir ( copyir.com com  The controller is not completely shut down when the main switch is turned off ( copyir ( copyir.com com
681    Toner bottle ID: Communication error
Communication error occurs when the toner bottle ID starts to communicate with the toner bottle ID receptor ( copyir ( copyir.com com  Retry of toner bottle ID communication fails three times after the machine has detected the toner bottle ID communication error ( copyir ( copyir.com com     Defective toner bottle ID reader and writer ( copyir ( copyir.com com  Disconnected ASAP I/F ( copyir ( copyir.com com  No memory chip on the toner cartridge ( copyir ( copyir.com com  Noise ( copyir ( copyir.com com
682    HST sensor: Communication error
Retry of memory chip communication fails three times after the machine has detected the memory chip communication error ( copyir ( copyir.com com     Damaged memory chip data ( copyir ( copyir.com com  Disconnected interface ( copyir ( copyir.com com  No memory chip on the development unit ( copyir ( copyir.com com  Noise ( copyir ( copyir.com com
687    Memory address (PER) command error
The BICU does not receive a memory address command from the controller 120 seconds after paper is in the position for registration ( copyir ( copyir.com com     Loose connection ( copyir ( copyir.com com  Defective controller ( copyir ( copyir.com com  Defective BICU ( copyir ( copyir.com com
790    Too many paper tray units
An attachment identification code is other than “01H” or ”02H” ( copyir ( copyir.com com     Number of paper tray units is more than the machine specification ( copyir ( copyir.com com
816    Energy saving I/O sub-system error    Controller board defective
819    Fatal kernel error [XXXX]: Detailed error code
Due to a control error, a RAM overflow occurred during system processing ( copyir ( copyir.com com  One of the following messages was displayed on the operation panel    System program defective ( copyir ( copyir.com com  Controller board defective ( copyir ( copyir.com com  Optional board defective ( copyir ( copyir.com com
820    Self-diagnostics error: CPU [XXXX]: Detailed error code    
821    Self-diagnostics error: CPU [XXXX]: Detailed error code    
822    Self-diagnostic error: HDD [XXXX]: Detailed error code    
823    Self-diagnostic error: NIB [XXXX]: Detailed error code    
824    Self-diagnostic error: NIB [XXXX]: Detailed error code    
827    Self-diagnostic error: Standard SDRAM DIMM [XXXX]: Detailed error code    
828    Self-diagnostic error: ROM [XXXX]: Detailed error code    
835    Self-diagnostic error: Standard SDRAM DIMM [XXXX]: Detailed error code    
838    Self-diagnostic Error: Clock Generator [XXXX]: Detailed error code    
839    USB NAND Flash ROM error [XXXX]: Detailed error code    
840    EEPROM error 1: EEPROM access
During the I/O processing, a reading error occurred ( copyir ( copyir.com com  The 3rd reading failure causes this SC code ( copyir ( copyir.com com  During the I/O processing, a writing error occurred ( copyir ( copyir.com com     Defective EEPROM
841    EEPROM error 2: EEPROM read/write error
Mirrored data of the EEPROM is different from the original data in EEPROM ( copyir ( copyir.com com     Data in the EEPROM is overwritten for some reason ( copyir ( copyir.com com
842    Flash ROM verification error
Verification error of the flash ROM on the controller board occurs ( copyir ( copyir.com com  Note: - This SC is logged at 1st error detection ( copyir ( copyir.com com SC819 is issued at 2nd error detection ( copyir ( copyir.com com  - SC819 is issued at 2nd error detection ( copyir ( copyir.com com     Defective flash ROM (controller board)
850    Network I/F error
Inoperative    
853    Bluetooth device connection error
The Bluetooth interface unit was installed while the machine was turned on ( copyir ( copyir.com com     
854    Bluetooth device connection error
The Bluetooth interface unit was removed while the machine was turned on ( copyir ( copyir.com com     
855    Hardware Problem:wireless LAN board
The wireless LAN board can be accessed, but an error was detected ( copyir ( copyir.com com     Loose connection ( copyir ( copyir.com com  Defective wireless LAN card ( copyir ( copyir.com com
858    HDD Encryption unit error 1
A serious error occurs when data is encrypted to update an encryption key with the HDD encryption unit ( copyir ( copyir.com com     
859    HDD Encryption unit error 2
A serious error occurs when the HDD data is encrypted to update an encryption key with the HDD encryption unit ( copyir ( copyir.com com     
860    HDD startup error at main power on
HDD is connected but a driver error is detected ( copyir ( copyir.com com  The driver does not respond to the HDD within 30 s ( copyir ( copyir.com com     HDD is not initialized ( copyir ( copyir.com com  Label data is corrupted ( copyir ( copyir.com com  Defective HDD ( copyir ( copyir.com com
862    Bad sector number error
The number of bad sectors in the HDD (image data area) goes over 101 ( copyir ( copyir.com com     Defective HDD
863    HDD: Read error
The data written to the HDD cannot be read normally, due to bad sectors generated during operation ( copyir ( copyir.com com  Note: -01 to -23 indicate the type of partition where the error occurred ( copyir ( copyir.com com  Enable display of these numbers with SP7902 ( copyir ( copyir.com com     HDD defective Note: If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM, and the next time the HDD is accessed, these bad sectors will not be accessed for read/write operation
864    HDD: CRC error
During HDD operation, the HDD cannot respond to a CRC error query ( copyir ( copyir.com com  Data transfer does not execute normally while data is being written to the HDD ( copyir ( copyir.com com  Note: -01 to -23 indicate the type of partition where the error occurred ( copyir ( copyir.com com  Enable display of these numbers with SP7902 ( copyir ( copyir.com com     HDD defective
865    HDD: Access error
HDD responded to an error during operation for a condition other than those for SC863, 864 ( copyir ( copyir.com com  Note: -01 to -23 indicate the type of partition where the error occurred ( copyir ( copyir.com com  Enable display of these numbers with SP7902 ( copyir ( copyir.com com     Defective HDD
866    SD card error: Confirmation
The machine detects an electronic license error in the application on the SD card in the controller slot immediately after the machine is turned on ( copyir ( copyir.com com  The program on the SD card contains electronic confirmation license data ( copyir ( copyir.com com  If the program does not contain this license data, or if the result of the check shows that the license data in the program on the SD card is incorrect, then the checked program cannot execute and this SC is displayed ( copyir ( copyir.com com     Program missing from the SD card
867    SD card error: SD card removed
The SD card is ejected from the slot while the machine is on ( copyir ( copyir.com com     
868    SD card error: SD card access -13 to -3: File system error Other number: Device error    SD card not inserted correctly ( copyir ( copyir.com com  SD card defective ( copyir ( copyir.com com  Controller board defective ( copyir ( copyir.com com
870    Address book error
The address book data cannot be read from the HDD, SD card or flash ROM on the controller where it is stored, or the data read from the media is defective ( copyir ( copyir.com com     Defective software program ( copyir ( copyir.com com  Defective HDD
872    HDD mail receive data error
The machine detects that the HDD is not operating correctly (can neither read nor write) at power on or while processing incoming email ( copyir ( copyir.com com     HDD defective ( copyir ( copyir.com com  Power failure during an access to the HDD
873    HDD mail send data error
An error is detected on the HDD immediately after the machine has been turned on, or power has been turned off while the machine has used the HDD ( copyir ( copyir.com com     Defective HDD ( copyir ( copyir.com com  Power failure during an access to the HDD ( copyir ( copyir.com com
874    Delete All error 1: Data area
An error occurs while the machine deletes data from the HDD ( copyir ( copyir.com com  Note: The source of this error is the DataOverwriteSecurity Unit running from an SD card ( copyir ( copyir.com com     An error detected at the delete program ( copyir ( copyir.com com  Delete All option is not installed ( copyir ( copyir.com com
875    Delete All error 1: HDD
A data error is detected for the HDD/NVRAM after the Delete All option has been used ( copyir ( copyir.com com  Note: The source of this error is the DataOverwriteSecurity Unit running from an SD card ( copyir ( copyir.com com     Defective HDD
876    Log Data Error
An error was detected in the handling of the log data at power on or during machine operation ( copyir ( copyir.com com  This can be caused by switching the machine off while it is operating ( copyir ( copyir.com com     
877    SD card error
The 'all delete' function cannot be executed but DataOverwriteSecurity Unit is installed and activated ( copyir ( copyir.com com     Defective SD card ( copyir ( copyir.com com  SD card not installed
878    TPM system authentication error    
880    File format converter (MLB) error
A request to get access to the MLB is not answered within the specified time (60 seconds) ( copyir ( copyir.com com     
881    Authentication area error
Authentication application error is detected ( copyir ( copyir.com com  Error data in an authentication application reaches the management limit ( copyir ( copyir.com com     
899    Software performance error
If the processing program shows abnormal performance and the program exits abnormally, this SC is issued ( copyir ( copyir.com com     Controller board defective ( copyir ( copyir.com com  Software defective
920    Printer error    Defective software ( copyir ( copyir.com com  Unexpected hardware resource (e ( copyir ( copyir.com com g ( copyir ( copyir.com com , memory shortage)
921    Printer font error
A necessary font is not found in the SD card ( copyir ( copyir.com com     A necessary font is not found in the SD card ( copyir ( copyir.com com  The SD card data is corrupted ( copyir ( copyir.com com
925    Net File function error
The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue ( copyir ( copyir.com com  The HDD is defective and it cannot be debugged or partitioned, so the Scan Router functions (delivery of received faxes, document capture, etc ( copyir ( copyir.com com ), Web services, and other network functions cannot be used ( copyir ( copyir.com com  HDD error status codes are displayed below the SC code:    Refer to the four procedures below (Recovery from SC 925) ( copyir ( copyir.com com
990    Software error 1
The software performs an unexpected function and the program cannot continue ( copyir ( copyir.com com     Software defective, re-boot
991    Software error 2
The software performs an unexpected function ( copyir ( copyir.com com  However, unlike SC990, recovery processing allows the program to continue ( copyir ( copyir.com com     Software defective, re-boot
992    Undefined error
Defective software program    An error undetectable by any other SC code occurred
994    Application Item Error
The number of executed application items on the operation panel reach the maximum limit for the operation panel structure ( copyir ( copyir.com com     Too many executed application items
997    Software Error 3: Cannot select application function
An application does not start after the user pushed the correct key on the operation panel ( copyir ( copyir.com com     Software bug ( copyir ( copyir.com com  A RAM or DIMM option necessary for the application is not installed or not installed correctly ( copyir ( copyir.com com
998    Software Error 4: Application cannot start
Register processing does not operate for an application within 60 s after the machine power is turned on ( copyir ( copyir.com com  No applications start correctly, and all end abnormally ( copyir ( copyir.com com     Software bug ( copyir ( copyir.com com  A RAM or DIMM option necessary for the application is not installed or not installed correctly ( copyir ( copyir.com com

خواندن 1004 دفعه

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب