Your browser does not support JavaScript! > کیو سرا میتا fsc8650dn
(0) محصول
یکشنبه, 12 ارديبهشت 1395 08:23

کیو سرا میتا fsc8650dn

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

0100    Backup memory device error    Defective EEPROM     copyir.com Defective main PWB     copyir.com
0120    MAC address data error
For data in which the MAC address is invalid     copyir.com    Defective EEPROM     copyir.com Defective engine PWB     copyir.com
0150    Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively     copyir.com Mismatch of reading data from 2 locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Improper installation EEPROM     copyir.com Defective engine PWB     copyir.com Device damage of EEPROM     copyir.com
0160    Backup memory data error (engine PWB)
Reading data from EEPROM is abnormal     copyir.com    Data damage of EEPROM     copyir.com
0170    Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters     copyir.com    Data damage of EEPROM     copyir.com Defective PWB     copyir.com
0180    Machine number mismatch
Machine number of main and engine does not match     copyir.com    Data damage of EEPROM     copyir.com
0640    Hard disk error
The hard disk cannot be accessed     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective hard disk     copyir.com Defective main PWB     copyir.com
0800    Image processing error
JAM010X is detected twice     copyir.com    Defective main PWB     copyir.com
0840    Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed     copyir.com    The battery is disconnected from the main PWB     copyir.com Defective main PWB     copyir.comnnec
0970    12 V power down detect
Power is disconnected during sleepingDetection of the temporary blackout during sleeping (24V is off, 23V is on, only the controller software is running)     copyir.com    Defective power source PWB     copyir.com
0980    24 V power down detect
24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected     copyir.com    Defective power source PWB     copyir.com
1000    MP lift motor error
After the MP lift motor is driven, the ON status of MP lift sensors 1 and 2 cannot be detected for 3 s     copyir.com    Defective MP plate elevation mechanism     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective MP lift motor     copyir.com Defective engine PWB     copyir.com
1010    Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s     copyir.com This error is detected 5 times successively     copyir.com The lock signal of the motor is detected continuously for 1 s     copyir.com This error is detected 5 times successively     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective lift motor 1     copyir.com Defective engine PWB     copyir.com
1020    Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s     copyir.com This error is detected 5 times successively     copyir.com The lock signal of the motor is detected continuously for 1 s     copyir.com This error is detected 5 times successively     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective lift motor 2     copyir.com Defective engine PWB     copyir.com
1030    PF lift motor 1 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s     copyir.com This error is detected 5 times successively     copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively     copyir.com However, the first 1 s after motor is turned on is excluded from detection     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF lift motor 1     copyir.com Defective PF main PWB     copyir.com
1040    PF lift motor 2 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s     copyir.com This error is detected 5 times successively     copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively     copyir.com However, the first 1 s after motor is turned on is excluded from detection     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF lift motor 2     copyir.com Defective PF main PWB     copyir.com
1050    SM lift motor error (side multi tray)
[45 ppm/55 ppm model] After cassette 5 is inserted, SM lift sensor does not turn on within 12 s     copyir.com This error is detected 5 times successively     copyir.com (Time to detect is 2 seconds at the second time and later     copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively     copyir.com However, the first 1 s after motor is turned on is excluded from detection     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective SM lift motor     copyir.com Defective SM main PWB     copyir.com
1060    PF lift motor 1 error (side paper feeder)
After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s     copyir.com This error is detected 5 times successively     copyir.com (Time to detect is 2 seconds at the second time and later     copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively     copyir.com However, the first 1 s after motor is turned on is excluded from detection     copyir.com *:The software over-current protection monitor signal has been detected for 200ms or longer where LFC is installed    Defective bottom plate elevation mechanism in the cassette     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF lift motor 1     copyir.com Defective PF main PWB     copyir.com
1070    PF lift motor 2 error (side paper feeder)
After cassette 7 is inserted, PF lift sensor 2 does not turn on within 12 s     copyir.com This error is detected 5 times successively     copyir.com (Time to detect is 2 seconds at the second time and later     copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively     copyir.com However, the first 1 s after motor is turned on is excluded from detection     copyir.com *:The software over-current protection monitor signal has been detected for 200ms or longer where LFC is installed    Defective bottom plate elevation mechanism in the cassette     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF lift motor 2     copyir.com Defective PF main PWB     copyir.com
1100    PF lift motor 1 error (large capacity feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 23 s     copyir.com This error is detected 5 times successively     copyir.com (Time to detect is 2 seconds at the second time and later     copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively     copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF lift motor 1     copyir.com Defective PF main PWB     copyir.com
1110    PF lift motor 2 error (large capacity feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s     copyir.com This error is detected 5 times successively     copyir.com (Time to detect is 2 seconds at the second time and later     copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively     copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF lift motor 2     copyir.com Defective PF main PWB     copyir.com
1140    SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s     copyir.com The lock signal of the motor is detected continuously for 200 ms     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective SD lift motor     copyir.com Defective SD main PWB     copyir.com
1250    SM multi feed sensor communication error (side multi tray)
A communication error is detected 3 times in succession     copyir.com    Improper installation side multi tray     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective engine PWB     copyir.com Defective SM main PWB     copyir.com
1350    SM multi feed sensor error (side multi tray)
The SM multi feed sensor has detected multi feeding 5 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective SM multi feed sensor     copyir.com Defective SM main PWB     copyir.com
1450    SM multi feed sensor backup error (side multi tray)
When writing the data, read and write data does not match 3 times in succession     copyir.com Deleting a block has failed three times in a row     copyir.com Writing won’t complete in 200 ms after writing has commenced     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective SM multi feed sensor     copyir.com Defective SM main PWB     copyir.com
1800    Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession     copyir.com    Improper installation paper feeder     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective engine PWB     copyir.com Defective PF main PWB     copyir.com
1810    Side multi tray communication error
A communication error from paper feeder is detected 10 times in succession     copyir.com    Improper installation side multi tray     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective engine PWB     copyir.com Defective SM main PWB     copyir.com
1820    Side paper feeder communication error
A communication error from paper feeder is detected 10 times in succession     copyir.com    Improper installation side paper feeder     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective engine PWB     copyir.com Defective SM main PWB     copyir.com Defective PF main PWB     copyir.com
1900    Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession     copyir.com    Defective PF main PWB     copyir.com Device damage of EEPROM     copyir.com
1910    Side multi tray EEPROM error
When writing the data, read and write data does not match 3 times in succession     copyir.com    Defective SM main PWB     copyir.com Device damage of EEPROM     copyir.com
1920    Side paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession     copyir.com    Defective PF main PWB     copyir.com Device damage of EEPROM     copyir.com
1950    Transfer belt unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively     copyir.com Mismatch of reading data from 2 locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective transfer belt unit     copyir.com
2101    Developer motor K error
After developer motor K is driven, the ready signal does not turn to L within 5 s     copyir.com After developer motor K is stabilized, the ready signal is at the H level for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective developer motor K     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2103    Developer motor MCY error
After developer motor MCY is driven, the ready signal does not turn to L within 5 s     copyir.com After developer motor MCY is stabilized, the ready signal is at the H level for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective developer motor MCY     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2201    Drum motor K steady-state error
After drum motor K is stabilized, the ready signal is at the H level for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective drum motor K     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2202    Drum motor C steady-state error
After drum motor C is stabilized, the ready signal is at the H level for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective drum motor C     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2203    Drum motor M steady-state error
After drum motor M is stabilized, the ready signal is at the H level for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective drum motor M     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2204    Drum motor Y steady-state error
After drum motor Y is stabilized, the ready signal is at the H level for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective drum motor Y     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2211    Drum motor K startup error
Drum motor K is not stabilized within 5 s since the motor is activated     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective drum motor K     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2212    Drum motor C startup error
Drum motor C is not stabilized within 5 s since the motor is activated     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective drum motor C     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2213    Drum motor M startup error
Drum motor M is not stabilized within 5 s since the motor is activated     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective drum motor M     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2214    Drum motor Y startup error
Drum motor Y is not stabilized within 5 s since the motor is activated     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective drum motor Y     copyir.com Defective Motor control PWB     copyir.com Defective engine PWB     copyir.com
2300    Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s     copyir.com After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective fuser motor     copyir.com Defective engine PWB     copyir.com
2500    Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective paper feed motor     copyir.com Defective engine PWB     copyir.com
2600    PF paper feed motor error (large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF paper feed motor     copyir.com Defective PF main PWB     copyir.com
2610    PF paper feed motor error (paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF main PWB     copyir.com
2640    SD paper feed motor error (side deck)
After SD paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective SD paper feed motor     copyir.com Defective SD main PWB     copyir.com
2650    SM paper feed motor error (side multi tray)
After SM paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective SM paper feed motor     copyir.com Defective SM main PWB     copyir.com
2660    PF paper feed motor error (side large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF paper feed motor     copyir.com Defective PF main PWB     copyir.com
2670    PF paper feed motor error (side paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective PF paper feed motor     copyir.com Defective PF main PWB     copyir.com
2700    Color release motor error
When the color release motor is driven, the color release sensor does not turn on/off for 5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective color release motor     copyir.com Defective engine PWB     copyir.com
2730    Transfer release motor error
When the transfer release motor is driven, the transfer release sensor does not turn on/off for 5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective transfer release motor     copyir.com Defective engine PWB     copyir.com
2760    Transfer motor startup error
Transfer motor is not stabilized within 5 s since the motor is activated     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective transfer motor     copyir.com Defective engine PWB     copyir.com
2770    Transfer skew error
An abnormal value is detected to transfer skew sensor     copyir.com    Improper installation transfer belt unit     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective transfer skew sensor     copyir.com Defective engine PWB     copyir.com
2780    Transfer skew sensor error
An abnormal value is detected to transfer skew sensor     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective transfer skew sensor     copyir.com Defective engine PWB     copyir.com
2790    Transfer skew motor error
When the transfer skew motor is driven, timeouts (300 ms) were detected twice in a row     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective transfer skew motor     copyir.com Defective engine PWB     copyir.com
2810    Waste toner motor error
Initialized when an error is constantly observed for 2 s after the waste toner motor is activated     copyir.com An error is constantly observed for 2     copyir.com5 s after rebooting     copyir.com The lock detect signal won’t be H level three times in a row within 200 ms at 1     copyir.com25 ms cycles after the waste toner motor has been driven     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective waste toner motor     copyir.comDefective engine PWB     copyir.com
2820    Transfer motor steady-state error
After transfer motor is stabilized, the ready signal is at the H level for 5 s continuously     copyir.com The counter value obtained by timer capture is lower than 2200 for 10 times in a row     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective transfer motor     copyir.com Defective engine PWB     copyir.com
2840    Transfer cleaning motor error
After transfer cleaning motor is driven, the ready signal does not turn to L within 2 s     copyir.com After transfer cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective transfer cleaning motor     copyir.com Defective engine PWB     copyir.com
2850    Transfer belt motor sensor error
The signal is not received for 100 ms in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective transfer motor     copyir.com Defective engine PWB     copyir.com
2860    Transfer belt sensor error
The signal is not received for 100 ms in succession     copyir.com PWB     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective transfer belt sensor     copyir.com Defective engine PWB     copyir.com
2950    Motor control PWB communication error
A communication error from the motor control PWB is detected 10 times in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective motor control PWB     copyir.com Defective engine PWB     copyir.com
4001    Polygon motor K synchronization error
After polygon motor K is driven, the ready signal does not turn to L within 30 s     copyir.com The polygon motor speed won’t stabilize within 10 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective polygon motor K     copyir.com Defective engine PWB     copyir.com
4002    Polygon motor C synchronization error
After polygon motor C is driven, the ready signal does not turn to L within 30 s     copyir.com The polygon motor speed won’t stabilize within 10 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective polygon motor C     copyir.com Defective engine PWB     copyir.com
4003    Polygon motor M synchronization error
After polygon motor M is driven, the ready signal does not turn to L within 30 s     copyir.com The polygon motor speed won’t stabilize within 10 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective polygon motor M     copyir.com Defective engine PWB     copyir.com
4004    Polygon motor Y synchronization error
After polygon motor Y is driven, the ready signal does not turn to L within 30 s     copyir.com The polygon motor speed won’t stabilize within 10 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective polygon motor Y     copyir.com Defective engine PWB     copyir.com
4011    Polygon motor K steadystate error
After polygon motor K is stabilized, the ready signal is at the H level for 15 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective polygon motor K     copyir.com Defective engine PWB     copyir.com
4012    Polygon motor C steadystate error
After polygon motor C is stabilized, the ready signal is at the H level for 15 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective polygon motor C     copyir.com Defective engine PWB     copyir.com
4013    Polygon motor M steadystate error
After polygon motor M is stabilized, the ready signal is at the H level for 15 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective polygon motor M     copyir.com Defective engine PWB     copyir.com
4014    Polygon motor Y steadystate error
After polygon motor Y is stabilized, the ready signal is at the H level for 15 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective polygon motor Y     copyir.com Defective engine PWB     copyir.com
4101    BD initialization error K
After polygon motor K is driven, the BD signal is not detected for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective PD PWB K     copyir.com Defective engine PWB     copyir.com
4102    BD initialization error C
After polygon motor C is driven, the BD signal is not detected for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective PD PWB C     copyir.com Defective engine PWB     copyir.com
4103    BD initialization error M
After polygon motor M is driven, the BD signal is not detected for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective PD PWB M     copyir.com Defective engine PWB     copyir.com
4104    BD initialization error Y
After polygon motor Y is driven, the BD signal is not detected for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective PD PWB Y     copyir.com Defective engine PWB     copyir.com
4201    BD steady-state error K
The BD signal is not detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective PD PWB K     copyir.com Defective engine PWB     copyir.com
4202    BD steady-state error C
The BD signal is not detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective PD PWB C     copyir.com Defective engine PWB     copyir.com
4203    BD steady-state error M
The BD signal is not detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective PD PWB M     copyir.com Defective engine PWB     copyir.com
4204    BD steady-state error Y
The BD signal is not detected     copyir.comector     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective PD PWB Y     copyir.com Defective engine PWB     copyir.com
4300    Polygon motor phase error
ASIC won’t settle in completion of phase adjustment for 2 s after a BD signal is detected     copyir.com    Defective laser scanner unit     copyir.com Defective engine PWB     copyir.com
4600    LSU cleaning motor error
After LSU cleaning motor is driven, the ready signal does not turn to L within 2 s     copyir.com After LSU cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective LSU cleaning motor     copyir.com Defective engine PWB     copyir.com
5101    Main high-voltage error K
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board)     copyir.com    Improper installation charger roller unit K     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective high voltage PWB 1     copyir.com Defective engine PWB     copyir.com
5102    Main high-voltage error C
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board)     copyir.com    Improper installation charger roller unit C     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective high voltage PWB 1     copyir.com Defective engine PWB     copyir.com
5103    Main high-voltage error M
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board)     copyir.com    Improper installation charger roller unit M     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective high voltage PWB 1     copyir.com Defective engine PWB     copyir.com
5104    Main high-voltage error Y
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board)     copyir.com    Improper installation charger roller unit Y     copyir.com Defective connector cable or poor contact in the connector     copyir.com Defective high voltage PWB 1     copyir.com Defective engine PWB     copyir.com
6000    Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 60 s during warming up     copyir.com The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Fuser thermostat triggered     copyir.com Defective fuser IH     copyir.com Defective engine PWB     copyir.com
6020    Abnormally high fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Shorted fuser thermistor 1     copyir.com Defective engine PWB     copyir.com
6030    Broken fuser thermistor 1 wire
Input from fuser thermistor 1 is 984 or more (A/D value) continuously for 1 s     copyir.com Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Broken fuser thermistor 1 wire     copyir.com Fuser thermostat triggered     copyir.com Defective fuser IH     copyir.com Defective engine PWB     copyir.com
6040    Fuser heater error
Input from fuser thermistor 1 is abnormal value continuously for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Broken fuser thermistor 1 wire     copyir.com Defective fuser IH     copyir.com Defective engine PWB     copyir.com
6050    Abnormally low fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print     copyir.com Fuser thermistor 1 detects a temperature lower than 70°C/ 158°F for 1 s during low power mode     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser thermistor 1     copyir.com Defective fuser IH     copyir.com Defective engine PWB     copyir.com
6120    Abnormally high fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature higher than 190°C/374°F for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Shorted fuser thermistor 4     copyir.com Defective engine PWB     copyir.com
6130    Broken fuser thermistor 4 wire
Input from fuser thermistor 4 is 992 or more (A/D value) continuously for 60 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Broken fuser thermistor 4 wire     copyir.com Defective fuser IH     copyir.com
6150    Abnormally low fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature lower than 30°C/ 86°F for 1 s after warming up     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser thermistor 4     copyir.com Defective fuser IH     copyir.com Defective engine PWB     copyir.com
6200    Broken fuser edge heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up     copyir.com The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Fuser thermostat triggered     copyir.com Defective fuser IH     copyir.com Defective engine PWB     copyir.com
6220    Abnormally high fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature higher than 245°C/473°F for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Shorted fuser thermistor 2     copyir.com Defective engine PWB     copyir.com
6230    Broken fuser thermistor 2 wire
The Input signal from the fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s when the temperature at the fuser thermistor 1 is greater than 100°C/212°F during warming up     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Broken fuser thermistor 2 wire     copyir.com Fuser thermostat triggered     copyir.com Defective fuser IH     copyir.com Defective engine PWB     copyir.com
6250    Abnormally low fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature lower than 100°C/212°F for 1 s during ready or print     copyir.com Fuser thermistor 2 detects a temperature lower than 50°C/ 122°F for 1 s during warming up     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser thermistor 2     copyir.com Defective fuser IH     copyir.com Defective engine PWB     copyir.com
6320    Abnormally high fuser thermistor 3 temperature
Fuser thermistor 3 detects a temperature higher than 205°C/401°F for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Shorted fuser thermistor 3     copyir.com Defective engine PWB     copyir.com
6330    Broken fuser thermistor 3 wire
Fuser thermistor 3 detects a temperature lower than 20°C/ 68°F continuously for 1 s    Defective connector cable or poor contact in the connector     copyir.com Broken fuser thermistor 3 wire     copyir.com Fuser thermostat triggered     copyir.com Defective fuser IH     copyir.com Defective engine PWB     copyir.com
6600    Fuser belt rotation error
A belt rotating pulse is not received for 1 s     copyir.com (Engine CPU)    Defective connector cable or poor contact in the connector     copyir.com Defective fuser belt sensor     copyir.com Defective engine PWB     copyir.com
6610    Fuser release motor error
When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drive transmission system of motor     copyir.com Defective fuser release motor     copyir.com Defective engine PWB     copyir.com
6710    Fuser IH PWB CPU reset error
Watch doc timer has been overflowed     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser IH PWB     copyir.com Defective engine PWB     copyir.com
6720    Fuser IH belt rotation error
A belt rotating pulse is not received for 2 s     copyir.comtiv    Defective connector cable or poor contact in the connector     copyir.com Defective fuser belt sensor     copyir.com Defective fuser IH PWB     copyir.com Defective engine PWB     copyir.com
6730    Abnormally high fuser IH PWB temperature 1
The input detect temperature is greater than 105°C/221 °F     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser IH PWB     copyir.com Defective engine PWB     copyir.com
6740    Abnormally high fuser IH PWB temperature 2
The input detect temperature is greater than 105°C/221 °F     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser IH PWB     copyir.com Defective engine PWB     copyir.com
6750    Fuser IH output over-current error
The output current is greater than 90A for 10 ms in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser IH PWB     copyir.com Defective engine PWB     copyir.com
6760    Fuser IH input over-current error
The input current is greater than 20A(100V/120V), 10A(200V) for 100 ms in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser IH PWB     copyir.com Defective engine PWB     copyir.com
6770    Fuser IH low electric power error
The preset power is less than 0     copyir.com6 times of it for 120 ms in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser IH PWB     copyir.com Defective engine PWB     copyir.com
6900    Fuser belt cooling fan error
When the fuser edge fan motor 1 , 2 is driven, alarm signal is detected for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser edge fan motor 1 or 2     copyir.com Defective engine PWB     copyir.com
6910    Engine software ready error
The device won’t engage in ready state in 60 minutes after warming-up has began     copyir.com    Defective engine software     copyir.com Defective engine PWB     copyir.com
6920    Fuser front fan motor error
When the fuser front fan motor is driven, alarm signal is detected for 5 s continuously    Defective connector cable or poor contact in the connector     copyir.com Defective fuser front fan motor     copyir.com Defective engine PWB     copyir.com
6930    Fuser rear fan motor error
When the fuser rear fan motor is driven, alarm signal is detected for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser rear fan motor     copyir.com Defective engine PWB     copyir.com
6940    IH fan motor error
When the IH fan motor is driven, the alarm signal is detected for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective IH fan motor     copyir.com Defective engine PWB     copyir.com
6950    Fuser IH PWB communication error
No response is received in 30 ms since a command is sent to IHCPU     copyir.com A checksum error is detected 10 times in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective fuser IH PWB     copyir.com Defective engine PWB     copyir.com
6960    Current PWB error
Less than 1A is continuously observed for 5 s     copyir.com    Defective current PWB     copyir.com
6990    Fuser power supply incompatibility
Information won’t match between the engine backup and the fuser IH PWB     copyir.com    Differences in settings after initialization     copyir.com Defective fuser IH PWB     copyir.com Defective engine PWB     copyir.com Data damage of EEPROM     copyir.com
7001    Toner motor K error
When the toner motor K is driven, the pulse sensor is not detected for 15 times in 200 ms intervals has occurred in 15 times     copyir.com During the toner motor is driven, an event in which TMOT_LOCK turns to H (locked) 5 times has occurred in 15 sets     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective screw sensor K     copyir.com Defective toner motor K     copyir.com Defective engine PWB     copyir.com
7002    Toner motor C error
When the toner motor K is driven, the pulse sensor is not detected for 15 times in 200 ms intervals has occurred in 15 times     copyir.com During the toner motor is driven, an event in which TMOT_LOCK turns to H (locked) 5 times has occurred in 15 sets     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective screw sensor C     copyir.com Defective toner motor C     copyir.com Defective engine PWB     copyir.com
7003    Toner motor M error
When the toner motor K is driven, the pulse sensor is not detected for 15 times in 200 ms intervals has occurred in 15 times     copyir.com During the toner motor is driven, an event in which TMOT_LOCK turns to H (locked) 5 times has occurred in 15 sets     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective screw sensor M     copyir.com Defective toner motor M     copyir.com Defective engine PWB     copyir.com
7004    Toner motor Y error
When the toner motor K is driven, the pulse sensor is not detected for 15 times in 200 ms intervals has occurred in 15 times     copyir.com During the toner motor is driven, an event in which TMOT_LOCK turns to H (locked) 5 times has occurred in 15 sets     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective screw sensor Y     copyir.com Defective toner motor Y     copyir.com Defective engine PWB     copyir.com
7101    Toner sensor K error
Sensor output value of 60 or less or 944 or more continued for 3 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective toner sensor K     copyir.com Failure of locking the developer waste slot at setup     copyir.com Defective engine PWB     copyir.com
7102    Toner sensor C error
Sensor output value of 60 or less or 944 or more continued for 3 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective toner sensor C     copyir.com Failure of locking the developer waste slot at setup     copyir.com Defective engine PWB     copyir.com
7103    Toner sensor M error
Sensor output value of 60 or less or 944 or more continued for 3 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective toner sensor M     copyir.com Failure of locking the developer waste slot at setup     copyir.com Defective engine PWB     copyir.com
7104    Toner sensor Y error
Sensor output value of 60 or less or 944 or more continued for 3 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective toner sensor Y     copyir.com Failure of locking the developer waste slot at setup     copyir.com Defective engine PWB     copyir.com
7200    Broken outer temperature sensor 2 wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective outer temperature sensor 2     copyir.com Defective engine PWB     copyir.com
7210    Short-circuited outer temperature sensor 2
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective outer temperature sensor 2     copyir.com efective engine PWB     copyir.com
7221    Broken LSU thermistor K wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective LSU thermistor K     copyir.com Defective engine PWB     copyir.com
7222    Broken LSU thermistor C wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective LSU thermistor C     copyir.com Defective engine PWB     copyir.com
7223    Broken LSU thermistor M wire The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective LSU thermistor M     copyir.com Defective engine PWB     copyir.com
7224    Broken LSU thermistor Y wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective LSU thermistor Y     copyir.com Defective engine PWB     copyir.com
7231    Short-circuited LSU thermistor K
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective LSU thermistor K     copyir.com Defective engine PWB     copyir.com
7232    Short-circuited LSU thermistor C
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective LSU thermistor C     copyir.com Defective engine PWB     copyir.com
7233    Short-circuited LSU thermistor M
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective LSU thermistor M     copyir.com Defective engine PWB     copyir.com
7234    Short-circuited LSU thermistor Y
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective LSU thermistor Y     copyir.com Defective engine PWB     copyir.com
7241    Broken developer thermistor K wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer thermistor K     copyir.com Defective engine PWB     copyir.com
7242    Broken developer thermistor C wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer thermistor C     copyir.com Defective engine PWB     copyir.com
7243    Broken developer thermistor M wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer thermistor M     copyir.com Defective engine PWB     copyir.com
7244    Broken developer thermistor Y wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer thermistor Y     copyir.com Defective engine PWB     copyir.com
7251    Short-circuited developer thermistor K
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer thermistor K     copyir.com Defective engine PWB     copyir.com
7252    Short-circuited developer thermistor C
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer thermistor C     copyir.com Defective engine PWB     copyir.com
7253    Short-circuited developer thermistor M
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer thermistor M     copyir.com Defective engine PWB     copyir.com
7254    Short-circuited developer thermistor Y wire
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer thermistor Y     copyir.com Defective engine PWB
7401    Developer unit K type mismatch error
Absence of the developer unit K is detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Different type of the developer unit is installed     copyir.com
7402    Developer unit C type mismatch error
Absence of the developer unit C is detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Different type of the developer unit is installed     copyir.com
7403    Developer unit M type mismatch error
Absence of the developer unit M is detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Different type of the developer unit is installed     copyir.com
7404    Developer unit Y type mismatch error
Absence of the developer unit Y is detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Different type of the developer unit is installed     copyir.com
7601    ID sensor 1 error
An abnormal value is detected in the input data to ID sensor 1     copyir.com Dark potential error FrontDarkP and FrontDarkS are greater than 0     copyir.com80V     copyir.com Light potential error FrontBrightS is smaller than FrontDarkS     copyir.com FrontBrightP is smaller than FrontDarkP + 0     copyir.com5V     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective engine PWB     copyir.com
7602    ID sensor 2 error
Dark potential error RearDarkP and RearDarkS are greater than 0     copyir.com80V     copyir.com Light potential error RearBrightS is smaller than RearDarkS     copyir.com RearBrightP is smaller than RearDarkP + 0     copyir.com5V     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective engine PWB     copyir.com
7800    Broken outer temperature sensor 1 wire
The device did not respond for more than 5 ms during reading, in 5 times     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective outer temperature sensor 1     copyir.com Defective engine PWB     copyir.com
7901    Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drum PWB K     copyir.com
7902    Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drum PWB C     copyir.com
7903    Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drum PWB M     copyir.com
7904    Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective drum PWB Y     copyir.com
7911    Developer unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer unit K     copyir.com
7912    Developer unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer unit C     copyir.com
7913    Developer unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer unit M     copyir.com
7914    Developer unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective developer unit Y     copyir.com
7941    Laser scanner unit K EEPROM error
Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective APC PWB K     copyir.com
7942    Laser scanner unit C EEPROM error
Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective APC PWB C     copyir.com
7943    Laser scanner unit M EEPROM error
Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective APC PWB M     copyir.com
7944    Laser scanner unit Y EEPROM error
Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective APC PWB Y     copyir.com
8010    Punch motor error 1
When the punch motor is driven, punch home position sensor does not turn on within 200 ms     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective punch home position sensor     copyir.com Defective punch motor     copyir.com Defective PWB     copyir.com
8020    Punch motor error 2
Home position is not obtained in 3 s after home position is initialized or in standby     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective punch motor     copyir.com Defective PWB     copyir.com
8030    Punch motor error 3
Home position does not turn from On to Off in 50 ms after home position has been initialized     copyir.comc?    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective punch motor     copyir.com Defective PWB     copyir.com
8040    Abnormal simultaneous connection of mailbox
When the mailbox is installed in both the main unit and the finisher     copyir.com    When the mailbox is installed in both the main unit and the finisher     copyir.com
8090    DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF paddle sensor     copyir.com Defective DF paddle motor     copyir.com Defective DF main PWB     copyir.com
8100    DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
8110    DF shift motor 1 error (4000-sheet finisher)
When the DF shift motor 1 is driven, DF shift sensor 1 does not turn on within 160 ms     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective DF shift sensor 1     copyir.com Defective DF shift motor 1     copyir.com Defective DF main PWB     copyir.com
8120    DF shift motor 2 error (4000-sheet finisher)
When the DF shift motor 2 is driven, DF shift sensor 2 does not turn on within 160 ms     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective DF shift sensor 2     copyir.com Defective DF shift motor 2     copyir.com Defective DF main PWB     copyir.com
8130    DF shift release motor error (4000-sheet finisher)
When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective DF shift release sensor     copyir.com Defective DF shift release motor     copyir.com Defective DF main PWB     copyir.com
8140    DF tray motor error 1
When the main tray has started ascending, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective sensor     copyir.com Defective DF tray motor     copyir.com Defective DF main PWB     copyir.com
8150    DF tray motor error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective sensor     copyir.com Defective DF tray motor     copyir.com Defective DF main PWB     copyir.com
8160    DF tray motor error 3
When the main tray has descended, DF tray sensor 3 does not turn on within 20 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF tray sensor 3     copyir.com Defective DF tray motor     copyir.com Defective DF main PWB     copyir.com
8170    DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF side registration sensor 1     copyir.com Defective DF side registration motor 1     copyir.com Defective DF main PWB     copyir.com
8180    DF side registration motor 1 error 2
JAM6810 is detected twice     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF side registration sensor 1     copyir.com Defective DF side registration motor 1     copyir.com Defective DF main PWB     copyir.com
8190    DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF side registration sensor 2     copyir.com Defective DF side registration motor 2     copyir.com Defective DF main PWB
8200    DF side registration motor 2 error 2
JAM6910 is detected twice     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF side registration sensor 2     copyir.com Defective DF side registration motor 2     copyir.com Defective DF main PWB     copyir.com
8210    DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF staple sensor     copyir.com Defective DF slide motor     copyir.com Defective DF main PWB     copyir.com
8230    DF staple motor error 1
Staple JAM (DF) has been detected twice in a row     copyir.com (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice     copyir.com)    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF staple sensor     copyir.com Defective DF staple motor     copyir.com Defective DF main PWB     copyir.com
8240    DF staple motor error 2
Staple JAM (DF) has been detected twice in a row     copyir.com (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven     copyir.com)    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF staple motor     copyir.com Defective DF main PWB     copyir.com
8250    DF tray motor error 4
The lock signal of the motor is detected continuously for 10 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective DF tray motor     copyir.com Defective DF main PWB     copyir.com
8300    Center-folding unit communication error (4000-sheet finisher)
Communication with the center- folding unit is not possible     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective CF set sensor     copyir.com Defective PWB     copyir.com
8310    CF side registration motor 2 error (4000-sheet finisher)
When initial operation, CF side registration sensor 2 does not turn on within 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective CF side registration sensor 2     copyir.com Defective CF side registration motor 2     copyir.com Defective CF main PWB     copyir.com
8320    CF adjustment motor error (4000-sheet finisher)
When initial operation, CF adjustment sensor does not turn on within 2     copyir.com5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective CF adjustment sensor 1, 2     copyir.com Defective CF adjustment motor 1, 2     copyir.com Defective CF main PWB     copyir.com
8330    CF blade motor error (4000-sheet finisher)
When initial operation, CF blade sensor does not turn on within 3 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective CF blade sensor     copyir.com Defective CF blade motor     copyir.com Defective CF main PWB     copyir.com
8340    CF staple motor error 1 (4000-sheet finisher)
Staple JAM (center-folding unit) has been detected twice in a row     copyir.com (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective CF staple sensor     copyir.com Defective CF staple motor     copyir.com Defective CF main PWB     copyir.com
8350    CF side registration motor 1 error (4000-sheet finisher)
When initial operation, CF side registration sensor 1 does not turn on within 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective CF side registration sensor 1     copyir.com Defective CF side registration motor 1     copyir.com Defective CF main PWB     copyir.com
8360    CF main motor error (4000-sheet finisher)
During driving the motor, lock signal is detected for 1 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective CF main motor     copyir.com Defective CF main PWB     copyir.com
8370    CF staple motor error 2 (4000-sheet finisher)
Staple JAM (DF) has been detected twice in a row     copyir.com (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 1000 ms continuously, while the stapler motor was driven     copyir.com)    Defective connector cable or poor contact in the connector     copyir.com Defective CF staple motor     copyir.com Defective CF main PWB     copyir.com
8410    Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective slide sensor     copyir.com Defective punch slide motor     copyir.com Defective PWB     copyir.com
8420    Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective punch slide motor     copyir.com Defective PWB     copyir.com
8430    Punch unit communication error
Communication failed to be established after the punch unit was hooked up     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective PWB     copyir.com
8500    Mailbox communication error (4000-sheet finisher)
Communication failed to be established after the mailbox was hooked up     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective PWB     copyir.com
8510    MB conveying motor error 1 (4000-sheet finisher)
When initial operation, MB home position sensor does not turn on within 5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective MB home position sensor     copyir.com Defective MB conveying motor     copyir.com Defective MB main PWB     copyir.com
8520    MB conveying motor error 2 (4000-sheet finisher)
When standby operation, MB home position sensor does not turn off within 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Defective MB home position sensor     copyir.com Defective MB conveying motor     copyir.com Defective MB main PWB     copyir.com
8800    Document finisher main program error Document finisher main program error at power up     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Defective PWB     copyir.com
8900    Document finisher backup error
Read and write data does not match 3 times in succession     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com Improper installation EEPROM     copyir.com Defective DF main PWB     copyir.com
8930    Center-folding unit backup error (4000-sheet finisher)
Read and write data does not match 3 times in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com Improper installation EEPROM     copyir.com Defective CF main PWB     copyir.com
F000    Communication error between main PWB and operation PWB    Defective main PWB     copyir.com Defective operation PWB     copyir.com
F010    Main PWB checksum error    Defective main PWB     copyir.com
F040    Communication error between main PWB and print engine    Defective main PWB     copyir.com Defective engine PWB     copyir.com
F050    Print engine ROM checksum error    Defective engine software     copyir.com Defective engine PWB     copyir.com
F278    Power supply in drive system error    The main power switch was turned off before the machine was shutdown, or a power failure has occurred     copyir.com

خواندن 872 دفعه
محتوای بیشتر در این بخش: « کیو سرا میتا fsc8600dn کیو سرا میتا km1500 »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب