Your browser does not support JavaScript! > کیو سرا میتا kmc3225e

   کانال تلگرام کپی ایران

(0) محصول
دوشنبه, 13 ارديبهشت 1395 11:10

کیو سرا میتا kmc3225e

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

C0030    Fax control PWB system problem (optional fax) Processing with the fax software was disabled due to a hardware or software problem       copyir.com    Defective fax control PWB       copyir.com
C0070    Abnormal detection of fax control PWB incompatibility (optional fax) In the initial communication with the fax control PWB, any normal communication command is not transmitted       copyir.com    Defective fax software       copyir.com Defective fax control PWB       copyir.com
C0100    Main PWB backup memory device problem Writing or erasing has not completed even after a certain time       copyir.com    Defective main PWB       copyir.com
C0110    Backup memory data problem Data in the specified area of the backup memory does not match the specified values       copyir.com    Problem with the backup memory data       copyir.com
C0150    Backup memory device problem (Engine PWB) An error occurs in backup data read or write for the engine PWB       copyir.com An error occurs in control area deletion       copyir.com    Defective engine PWB       copyir.com Data damage of EEPROM       copyir.com
C0160    Backup memory data problem (Engine PWB) Data for backup data check is changed at the check after startup       copyir.com    Problem with the backup memory data       copyir.com
C0170    Copy counts problem A checksum error is detected in the main and sub backup memories for the copy counters       copyir.com    Data damage of EEPROM       copyir.comDefective main PWB       copyir.com
C0180    Backup memory data problem Backup data on the main PWB has broken       copyir.com    Data damage of EEPROM       copyir.com
C0210    CPU communication problem There is no reply after 3 retries at communication       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C0220    Communication problem between the scanner PWB and main PWB There is no reply after 6 retries at communication       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C0240    Printer PWB communication problem The printer PWB does not respond 120 s after the power is turned on       copyir.com    Poor contact in the connector terminals       copyir.com DIMM or DDR installed incorrectly       copyir.com Defective PWB       copyir.com
C0250    Network scanner PWB communication problemThe response to the alive command to the network scanner transmitted once to 30 s does not come on the contrary three consecutive times or more       copyir.com The response to the communication command transmitted to the network scanner does not return 75 s or more       copyir.com (This code indicates only scanner function display       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C0280    Communication problem between the fax control PWB and main PWB After main PWB status change signal turns on 1 minute, when it does not receive key required command from the fax control PWB, one time it resets the FAX       copyir.comAfter that, while main PWB status change signal turns on furthermore 1 minute, when it does not receive key required command from the fax control PWB       copyir.com When FAX_READY signal continues fake for 6 s, one time it resets the FAX       copyir.com After that, when FAX_READY fake continues fake for 6 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C0410    DP communication problem (optional DP) There is no reply after 10 retries at communication or a communication error occurs       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C0420    Paper feeder communication error (optional paper feeder) A communication error from paper feeder is detected 10 times in succession       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C0440    Document finisher communication problem (optional document finisher) A communication error from document finisher is detected 10 times in succession       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C0610    Bitmap problem The DIMM on the main PWB does not operate correctly       copyir.com    Defective main PWB       copyir.com DDR on the main PWB installed incorrectly       copyir.com
C0630    DMA problem DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time       copyir.com    Defective main PWB       copyir.com DDR on the main PWB installed incorrectly       copyir.com
C0640    Hard disk drive problem The hard disk cannot be accessed       copyir.com    Poor contact in the connector terminals       copyir.com Defective hard disk       copyir.com Defective main PWB       copyir.com
C0820    Fax control PWB CG ROM checksum error (optional fax) A checksum error occurred with the CG ROM data of the fax control PWB       copyir.com    Defective fax software       copyir.com Defective fax control PWB       copyir.com
C0830    Fax control PWB flash program area checksum error (optional fax) A checksum error occurred with the program of the fax control PWB       copyir.com    Defective fax software       copyir.com Defective fax control PWB       copyir.com
C0840    Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed       copyir.com    Defective main PWB       copyir.com The battery is disconnected from the main PWB       copyir.com
C0860    Fax control PWB software switch checksum error (optional fax) A checksum error occurred with the software switch value of the fax control PWB       copyir.com    Defective fax software       copyir.com Defective fax control PWB       copyir.com
C0870    Fax control PWB to main PWB high capacity data transfer problem High-capacity data transfer between the fax control PWB and the scanner MIP PWB was not normally performed even if the data transfer was retried 10 times       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C0880    Program archive problem (optional fax) When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed       copyir.com    Defective fax software       copyir.com Defective fax control PWB       copyir.com
C0890    Fax control PWB CG FONT archive problem (optional fax) When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed       copyir.com    Defective fax software       copyir.com Defective fax control PWB       copyir.com
C0920    Fax file system error The backup data is not retained for file system abnormality of flash memory of the fax control PWB       copyir.com    Defective fax control PWB       copyir.com
C1010    Lift motor 1 error When cassette 1 is inserted, lift limit switch 1 does not turn on within 12 s of lift motor 1 turning on       copyir.com    Poor contact in the connector terminals       copyir.com Broken gears or couplings of lift motor 1       copyir.com Defective lift motor 1       copyir.com Defective lift switch 1       copyir.com Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C1020    Lift motor 2 error When cassette 2 is inserted, lift limit switch 2 does not turn on within 12 s of lift motor 2 turning on       copyir.com    Poor contact in the connector terminals       copyir.com Broken gears or couplings of lift motor 2       copyir.com Defective lift motor 2       copyir.com Defective lift switch 2       copyir.com Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C1030    Paper feeder lift motor 1 error (optional paper feeder) When optional cassette 3 is inserted, paper feeder lift switch 1 does not turn on within 12 s of paper feeder lift motor 1 turning on       copyir.com The lift overcurrent protective monitor signal is detected above 500 ms during driving the motor       copyir.com However, the first 1 s after paper feeder lift motor 1 is turned on is excluded from detection       copyir.com    Poor contact in the connector terminals       copyir.com Broken gears or couplings of paper feeder lift motor 1       copyir.com Defective paper feeder lift motor 1       copyir.com Defective paper feeder lift switch 1       copyir.com
C1040    Paper feeder lift motor 2 error (optional paper feeder) When optional cassette 4 is inserted, paper feeder lift switch 2 does not turn on within 12 s of paper feeder lift motor 2 turning on       copyir.com The lift overcurrent protective monitor signal is detected above 500 ms during driving the motor       copyir.com However, the first 1 s after paper feeder lift motor 2 is turned on is excluded from detection       copyir.com    Poor contact in the connector terminals       copyir.com Broken gears or couplings of paper feeder lift motor 2       copyir.com Defective paper feeder lift motor 2       copyir.com Defective paper feeder lift switch 2       copyir.com
C1100    Paper feeder lift motor 1 error (optional 3000-sheet paper feeder) A motor over-current signal is detected continuously for 1 s or longer       copyir.com    Poor contact in the connector terminals       copyir.com Paper feeder lift motor 1 does not rotate correctly (the motor is overloaded)       copyir.com
C1110    Paper feeder lift motor 2 error (optional 3000-sheet paper feeder) A motor over-current signal is detected continuously for 1 s or longer       copyir.com    Poor contact in the connector terminals       copyir.com Paper feeder lift motor 2 does not rotate correctly (the motor is overloaded)       copyir.com
C1120    Paper feeder left lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 1 does not turn on within 30 s of paper feeder lift motor 2 turning on       copyir.com    Poor contact in the connector terminals       copyir.com Defective paper feeder lift switch 1       copyir.com Defective paper feeder lift motor 2       copyir.com The paper feeder left lift does not rise properly       copyir.com
C1130    Paper feeder right lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 2 does not turn on within 30 s of paper feeder lift motor 1 turning on       copyir.com    Poor contact in the connector terminals       copyir.com Defective paper feeder lift switch 2       copyir.com Defective paper feeder lift motor 1       copyir.com The paper feeder right lift does not rise properly       copyir.com
C1900    Paper feeder EEPROM error (optional paper feeder) When writing the data, the write data and the read data is not continuously in agreement three times       copyir.com    Poor contact in the connector terminals       copyir.com Defective engine PWB       copyir.com Defective paper feeder       copyir.com
C1950    Transfer belt unit EEPROM error Read and write data does not match       copyir.com    Poor contact in the connector terminals       copyir.com Defective transfer belt speed detection PWB (inner transfer belt unit)       copyir.com
C2101    Paper feed/developing motor BK error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective drive transmission system       copyir.com Defective engine PWB       copyir.com Defective paper feed/developing motor BK       copyir.com
C2102    Developing motor CMY error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective drive transmission system       copyir.com Defective engine PWB       copyir.com Defective developing motor CMY       copyir.com
C2201    Drum motor BK error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective drum motor BK       copyir.com Defective PWB       copyir.com
C2202    Drum motor C error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective drum motor C       copyir.com Defective PWB       copyir.com
C2203    Drum motor M error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective drum motor M       copyir.com Defective PWB       copyir.com
C2204    Drum motor Y error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective drum motor Y       copyir.com Defective PWB       copyir.com
C2300    Fuser motor error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective drive transmission system       copyir.com Defective engine PWB       copyir.com Defective fuser motor       copyir.com
C2400    Eject motor error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective drive transmission system       copyir.com Defective engine PWB       copyir.com Defective eject motor       copyir.com
C2500    MP motor error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective drive transmission system       copyir.com Defective engine PWB       copyir.com Defective MP motor       copyir.com
C2600    Paper feeder paper conveying motor error (optional paper feeder) The lock signal of the motor is detected above 450 ms       copyir.com    Poor contact in the connector terminals       copyir.com Defective drive transmission system       copyir.com Defective PWB       copyir.com Defective paper feeder paper conveying motor       copyir.com
C2810    Waste toner motor error The rated speed achievement signal won’t turn to L in 5 s since the motor is activated       copyir.com The rated speed achievement signal turns to H every other 5 s after the machine is stabilized       copyir.com    Poor contact in the connector terminals       copyir.com Defective drive transmission system       copyir.com Defective waste toner motor       copyir.com Defective engine PWB       copyir.com
C3100    Scanner carriage problem The home position is not correct when the power is turned on or at the start of copying using the table       copyir.com    Defective scanner PWB       copyir.com Defective scanner home position switch       copyir.com Defective scanner motor       copyir.com Poor contact in the connector terminals       copyir.com The mirror frame, exposure lamp, or scanner wire is defective       copyir.com
C3200    Exposure lamp problem The exposure lamp is not turned on when starting the copy       copyir.com    Poor contact in the connector terminals       copyir.com Defective scanner PWB       copyir.com Defective CCD PWB       copyir.com Defective exposure lamp or inverter PWB       copyir.com Incorrect shading position       copyir.com
C3300    Optical system (AGC) problem After AGC, correct input is not obtained at CCD       copyir.com    Poor contact in the connector terminals       copyir.com Defective exposure lamp       copyir.com Defective PWB       copyir.com
C3500    Communication error between scanner and SHD An error code is detected       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB
C3900    Backup memory read/write problem (scanner PWB) Read and write data does not match       copyir.com    Defective backup RAM or scanner PWB       copyir.com
C3910    Backup memory data problem (scanner PWB) Data in the specified area of the backup memory does not match the specified values       copyir.com    Problem with the backup memory data       copyir.com Defective scanner PWB       copyir.com
C4000    Polygon motor synchronization problem The rated speed achievement signal won’t turn to L in 20 s since the polygon motor is activated       copyir.com    Poor contact in the connector terminals       copyir.com Defective polygon motor       copyir.com Defective engine PWB       copyir.com
C4010    Polygon motor steady-state problem The rated speed achievement signal turns to H every other 5 s after the polygon motor is stabilized       copyir.com    Poor contact in the connector terminals       copyir.com Defective polygon motor       copyir.com Defective engine PWB       copyir.com
C4100    BD initialization problem When power is turned on, ASIC of engine PWB detects a BD error for 200 ms       copyir.com    Poor contact in the connector terminals       copyir.com Defective APC PWB BK (inner laser scanner unit) Defective engine PWB       copyir.com
C4200    BD steady-state problem ASIC of the engine PWB detects a BD error for 200 ms after the polygon motor rotation has been stabilized       copyir.com    Poor contact in the connector terminals       copyir.com Defective laser scanner unit       copyir.com Defective engine PWB       copyir.com
C5101    Main high-voltage BK error Abnormality of charger roller BK is detected when Vpp adjustment       copyir.com    Installation defectiveness on charger roller unit BK       copyir.com Defective charger roller unit BK       copyir.com
C5102    Main high-voltage C error Abnormality of charger roller C is detected when Vpp adjustment       copyir.com    Installation defectiveness on charger roller unit C       copyir.com Defective charger roller unit C       copyir.com
C5103    Main high-voltage M error Abnormality of charger roller M is detected when Vpp adjustment       copyir.com    Installation defectiveness on charger roller unit M       copyir.com Defective charger roller unit M       copyir.com
C5104    Main high-voltage Y error Abnormality of charger roller Y is detected when Vpp adjustment       copyir.com    Installation defectiveness on charger roller unit Y       copyir.com Defective charger roller unit Y       copyir.com
C5301    Cleaning lamp BK break error After the cleaning lamp BK ON signal is turned on, the cleaning lamp BK break signal is detected continuously 5 times for 10 ms       copyir.com    Poor contact in the connector terminals       copyir.com Defective cleaning lamp BK       copyir.com Defective engine PWB       copyir.com
C5302    Cleaning lamp C break error After the cleaning lamp C ON signal is turned on, the cleaning lamp C break signal is detected continuously 5 times for 10 ms       copyir.com    Poor contact in the connector terminals       copyir.com Defective cleaning lamp C       copyir.com Defective engine PWB       copyir.com
C5303    Cleaning lamp M break error After the cleaning lamp M ON signal is turned on, the cleaning lamp M break signal is detected continuously 5 times for 10 ms       copyir.com    Poor contact in the connector terminals       copyir.com Defective cleaning lamp M       copyir.com Defective engine PWB       copyir.com
C5304    Cleaning lamp Y break error After the cleaning lamp Y ON signal is turned on, the cleaning lamp Y break signal is detected continuously 5 times for 10 ms       copyir.com    Poor contact in the connector terminals       copyir.com Defective cleaning lamp Y       copyir.com Defective engine PWB       copyir.com
C6000    Fuser thermistor 1/3 break error Fuser thermistor 1 detected 40 C/104 F or less during warming up       copyir.com 40 C/104 F or less is detected between 10 s of continuation during worming up       copyir.com Fuser thermistor 3 detected 40 C/104 F or less during warming up       copyir.com    Defective fuser heater 1/2       copyir.com Defective fuser thermostat 1       copyir.com Installation defectiveness on fuser thermistor 1/2       copyir.com Defective PWB       copyir.com
C6010    Abnormally high fuser thermistor temperature The fuser Abnormally high signal is detected for 60 s or more       copyir.com    Defective PWB       copyir.com
C6020    Abnormally high fuser thermistor 1/3 temperature The fuser temperature exceeds 240 C/ 464 F       copyir.com    Defective PWB       copyir.com Installation defectiveness on fuser thermistor 1/3       copyir.com
C6030    Fuser thermistor 1/3 break error Fuser thermistor 1 detected 40 C/104 F or less during warming up       copyir.com 40 C/104 F or less is detected between 10 s of continuation during worming up       copyir.com Fuser thermistor 3 detected 40 C/104 F or less during warming up       copyir.com    Defective fuser heater 1/2       copyir.com Installation defectiveness on fuser thermistor 1/3       copyir.com Defective PWB       copyir.com
C6050    Abnormally low fuser thermistor 3 temperature During copying, the temperature at the heat roller lower than 100 C/212 F is detected continuously for 1 s       copyir.com    Defective fuser heater 1/2       copyir.com Defective PWB       copyir.com
C6100    Fuser heater 3 break Fuser thermistor 2 detected less than 100 C/212 F for 120 s during driving       copyir.com Fuser thermistor 2 deduced less than 150 C/302 F for 300 s during driving       copyir.com Fuser thermistor 2 deduced less than 100 C/212 F for 5 s during driving       copyir.com    Defective fuser heater 3       copyir.com Defective fuser thermostat 2       copyir.com Installation defectiveness on fuser thermistor 2       copyir.com Defective PWB       copyir.com
C6120    Abnormally high fuser thermistor 2 temperature The fuser temperature exceeds 190 C/ 374 F       copyir.com    Installation defectiveness on fuser thermistor 2       copyir.com Defective PWB       copyir.com
C6130    Fuser thermistor 2 break error Fuser thermistor 2 detected less than 40 C/104 F during driving       copyir.com When the difference of temperature of fuser thermistor 1 and 3 becomes 100 C/212 F or more       copyir.com    Installation defectiveness on fuser thermistor 2       copyir.com Defective fuser heater 3       copyir.com Defective PWB       copyir.com
C6400    Zero-cross signal error While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 3 s       copyir.com    Defective PWB       copyir.com
C7000    Toner motor problem The rated speed achievement signal won’t turn to L in 5 s since the motor is activated       copyir.com The rated speed achievement signal turns to H every other 5 s after the machine is stabilized       copyir.com    Poor contact in the connector terminals       copyir.com Broken the gear       copyir.com Defective toner motor M/C/Y/BK       copyir.com Defective engine PWB       copyir.com
C7101    Toner sensor BK problem Sensor output value of 78 or less or 944 or more continued for 3 s       copyir.com    Defective developing unit BK       copyir.com Defective engine PWB       copyir.com
C7102    Toner sensor C problem Sensor output value of 78 or less or 944 or more continued for 3 s       copyir.com    Defective developing unit C       copyir.com Defective engine PWB       copyir.com
C7103    Toner sensor M problem Sensor output value of 78 or less or 944 or more continued for 3 s       copyir.com    Defective developing unit M       copyir.com Defective engine PWB       copyir.com
C7104    Toner sensor Y problem Sensor output value of 78 or less or 944 or more continued for 3 s       copyir.com    Defective developing unit Y       copyir.com Defective engine PWB       copyir.com
C7200    Broken internal thermistor wire An abnormal value is detected in the input data to inner temperature sensor 1       copyir.com    Poor contact in the connector terminals       copyir.com Defective laser scanner unit       copyir.com Defective engine PWB       copyir.com
C7210    Short-circuited internal thermistor An abnormal value is detected in the input data to inner temperature sensor 1       copyir.com    Poor contact in the connector terminals       copyir.com Defective laser scanner unit       copyir.com Defective engine PWB       copyir.com
C7220    Broken internal thermistor 2 wire An abnormal value is detected in the input data to inner temperature sensor 2       copyir.com    Poor contact in the connector terminals       copyir.com Defective engine PWB       copyir.com
C7230    Short-circuited internal thermistor 2 An abnormal value is detected in the input data to inner temperature sensor 2       copyir.com    Poor contact in the connector terminals       copyir.com Defective engine PWB       copyir.com
C7240    Broken internal thermistor 3 wire An abnormal value is detected in the input data to inner temperature sensor 3       copyir.com    Poor contact in the connector terminals       copyir.com Defective engine PWB       copyir.com
C7250    Short-circuited internal thermistor 3 An abnormal value is detected in the input data to inner temperature sensor 3       copyir.com    Poor contact in the connector terminals       copyir.com Defective engine PWB       copyir.com
C7401    Developing unit BK type mismatch problem Absence of the developing unit BK is detected       copyir.com    Developing unit connector inserted incorrectly       copyir.com Different type of the developing unit is installed       copyir.com
C7402    Developing unit C type mismatch problem Absence of the developing unit C is detected       copyir.com    Developing unit connector inserted incorrectly       copyir.com Different type of the developing unit is installed       copyir.com
C7403    Developing unit M type mismatch problem Absence of the developing unit M is detected       copyir.com    Developing unit connector inserted incorrectly       copyir.com Different type of the developing unit is installed       copyir.com
C7404    Developing unit Y type mismatch problem Absence of the developing unit Y is detected       copyir.com    Developing unit connector inserted incorrectly       copyir.com Different type of the developing unit is installed       copyir.com
C7411    Drum unit BK type mismatch problem Absence of the drum unit BK is detected       copyir.com    Drum unit connector inserted incorrectly       copyir.com Different type of the drum unit is installed       copyir.com
C7412    Drum unit C type mismatch problem Absence of the drum unit C is detected       copyir.com    Drum unit connector inserted incorrectly       copyir.com Different type of the drum unit is installed       copyir.com
C7413    Drum unit M type mismatch problem Absence of the drum unit M is detected       copyir.com    Drum unit connector inserted incorrectly       copyir.com Different type of the drum unit is installed       copyir.com
C7414    Drum unit Y type mismatch problem Absence of the drum unit Y is detected       copyir.com    Drum unit connector inserted incorrectly       copyir.com Different type of the drum unit is installed       copyir.com
C7420    Transfer belt unit type mismatch problem Absence of the transfer belt unit is detected       copyir.com    Transfer belt unit connector inserted incorrectly       copyir.com Different type of the transfer belt unit is installed       copyir.com
C7800    Broken external thermistor wire An abnormal value is detected in the input data to the outer temperature sensor       copyir.com    Poor contact in the connector terminals       copyir.com Defective engine PWB       copyir.com
C7810    Short-circuited external thermistor An abnormal value is detected in the input data to the outer temperature sensor       copyir.com    Poor contact in the connector terminals       copyir.com Defective engine PWB       copyir.com
C7901    Drum BK EEPROM error Reading from or writing to EEPROM cannot be performed       copyir.com    Poor contact in the connector terminals       copyir.com Defective drum PWB BK       copyir.com
C7902    Drum C EEPROM error Reading from or writing to EEPROM cannot be performed       copyir.com    Poor contact in the connector terminals       copyir.com Defective drum PWB C       copyir.com
C7903    Drum M EEPROM error Reading from or writing to EEPROM cannot be performed       copyir.com    Poor contact in the connector terminals       copyir.com Defective drum PWB M       copyir.com
C7904    Drum Y EEPROM error Reading from or writing to EEPROM cannot be performed       copyir.com    Poor contact in the connector terminals       copyir.com Defective drum PWB Y       copyir.com
C7911    Developing unit BK EEPROM error Reading from or writing to EEPROM cannot be performed       copyir.com    Poor contact in the connector terminals       copyir.com Defective developing PWB BK       copyir.com
C7912    Developing unit C EEPROM error Reading from or writing to EEPROM cannot be performed       copyir.com    Poor contact in the connector terminals       copyir.com Defective developing PWB C       copyir.com
C7913    Developing unit M EEPROM error Reading from or writing to EEPROM cannot be performed       copyir.com    Poor contact in the connector terminals       copyir.com Defective developing PWB M       copyir.com
C7914    Developing unit Y EEPROM error Reading from or writing to EEPROM cannot be performed       copyir.com    Poor contact in the connector terminals       copyir.com Defective developing PWB Y       copyir.com
C8020    Punch motor problem (optional 3000 sheet document finisher) The LOCK signal of the punch motor is detected for more than 500 ms while the punch motor is operating       copyir.com    Poor contact in the connector terminals       copyir.com Defective punch motor       copyir.com Defective PWB       copyir.com
C8030    Tray upper limit detection problem (optional document finisher) When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected       copyir.com    The tray upper limit sensor/push paper sensor/surface view sensor connector makes poor contact       copyir.com Defective tray upper limit sensor/ push paper sensor/ surface view sensor       copyir.com Defective finisher main PWB       copyir.com
C8050    Paper conveying belt motor 1 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 1 does not turn off within 1       copyir.com5 s       copyir.com Paper conveying belt home position sensor 1 does not turn on within 2       copyir.com5 s       copyir.com Jam 88 is indicated       copyir.com    Poor contact in the connector terminals       copyir.com Defective paper conveying belt home position sensor 1       copyir.com Defective paper conveying belt motor 1       copyir.com Defective PWB       copyir.com
C8060    Paper conveying belt motor 2 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 2 does not turn off within 1       copyir.com5 s       copyir.com Paper conveying belt home position sensor 2 does not turn on within 1       copyir.com5 s       copyir.com    Poor contact in the connector terminals       copyir.com Defective paper conveying belt home position sensor 2       copyir.com Defective paper conveying belt motor 2       copyir.com Defective PWB       copyir.com
C8070    Internal tray communication error (optional 3000-sheet document finisher) Communication with the internal tray is not possible although the connection is detected       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C8140    Main tray problem (optional 3000- sheet document finisher) The main tray is not detected by the main tray upper limit detection sensor or the main tray paper upper surface detection sensor within 20s since the tray has started ascending       copyir.com The main tray upper limit detection sensor or the main tray paper upper surface detection sensor is not detected to be turned off in 20 s after the main tray has descended       copyir.com The main tray low limit detection sensor is not detected to be turned on in 20 s after the main tray has descended       copyir.com During main tray ascent, the main tray upper limit detection sensor or the main tray paper upper surface detection sensor stays on for more than 2 s       copyir.com    Poor contact in the connector terminals Defective main tray motor        copyir.comDefective main tray upper limit detection sensor/main tray paper upper surface detection sensor/main tray lower limit detection sensor       copyir.com Defective finisher main PWB       copyir.com
C8140    Tray elevation motor problem (optional document finisher) The tray low limit sensor, paper retaining sensor or paper surface sensor cannot be detected to be on within 10 s since the tray elevation motor is activated       copyir.com    The tray elevation motor connector makes poor contact       copyir.com The tray elevation motor malfunctions       copyir.com The tray lower limit sensor/push paper sensor/surface view sensor connector makes poor contact       copyir.com Defective tray lower limit sensor/ push paper sensor/ surface view sensor       copyir.com Defective finisher main PWB       copyir.com
C8170    Side registration motor 1 problem (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 s passed       copyir.com Jam 88 is indicated       copyir.com    Poor contact in the connector terminals       copyir.com Defective side registration motor 1       copyir.com Defective PWB       copyir.com
C8170    Adjustment motor problem (optional document finisher) The registration home position sensor cannot be detected to be on or off within 125 ms since the registration motor is activated after registration has started       copyir.com The registration home position sensor cannot be detected to be on within 710 ms since the registration motor is activated after registration has ceased       copyir.com    The adjustment motor connector makes poor contact Defective adjustment motor       copyir.com The adjustment home position sensor connector makes poor contact       copyir.com Defective adjustment home position sensor       copyir.com Defective finisher main PWB       copyir.com
C8180    Side registration motor 2 problem (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 s passed       copyir.com Jam 88 is indicated       copyir.com    Poor contact in the connector terminals       copyir.com Defective side registration motor 2       copyir.com Defective PWB       copyir.com
C8210    Stapler shift motor 1 error (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 1       copyir.com5 s passed       copyir.com    Poor contact in the connector terminals       copyir.com Defective stapler shift motor 1       copyir.com Defective finisher main PWB       copyir.com
C8210    Stapler problem (optional document finisher) When the stapler motor is driving, the ON status of the stapler home position sensor cannot be detected even if 1 s passed       copyir.com    The stapler connector makes poor contact       copyir.com The stapler is blocked with a staple       copyir.com The stapler is broken       copyir.com Defective finisher main PWB       copyir.com
C8220    Stapler shift motor 2 error (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3       copyir.com5 s passed       copyir.com    Poor contact in the connector terminals       copyir.com Defective stapler shift motor 2       copyir.com Defective finisher main PWB       copyir.com
C8230    Stapler motor problem (optional 3000sheet document finisher) Jam 82 is indicated       copyir.com    Poor contact in the connector terminals       copyir.com Defective stapler motor       copyir.com Defective finisher main PWB       copyir.com
C8300    Centerfold unit communication error (optional centerfold unit of 3000-sheet document finisher) Communication with the centerfold unit is not possible although the connection is detected       copyir.com    Poor contact in the connector terminals       copyir.com Defective centerfold set switch       copyir.com Defective finisher main PWB       copyir.com
C8310    Centerfold side registration motor 1 problem (optional centerfold unit of 3000-sheet document finisher) The home position is not detected when initial operation even if 1 s passed       copyir.com    Poor contact in the connector terminals       copyir.com Defective centerfold side registration motor 1       copyir.com Defective PWB       copyir.com
C8320    Centerfold paper conveying belt motor problem (optional centerfold unit of 3000-sheet document finisher) The home position is not detected when initial operation even if 2       copyir.com5 s passed       copyir.com    Poor contact in the connector terminals       copyir.com Defective centerfold paper conveying belt motor 1/2       copyir.com Defective PWB       copyir.com
C8330    Blade motor problem (optional centerfold unit of 3000-sheet document finisher) The home position is not detected when initial operation even if 1       copyir.com5 s passed       copyir.com    Poor contact in the connector terminals       copyir.com Defective blade motor       copyir.com Defective PWB       copyir.com
C8340    Centerfold staple motor problem (optional centerfold unit of 3000-sheet document finisher) Jam89 is indicated       copyir.com    Poor contact in the connector terminals       copyir.com Defective centerfold staple motor       copyir.com Defective PWB       copyir.com
C8350    Centerfold side registration motor 2 problem (optional centerfold unit of 3000-sheet document finisher) The home position is not detected when initial operation even if 1 s passed       copyir.com    Poor contact in the connector terminals       copyir.com Defective centerfold side registration motor 2       copyir.com Defective PWB       copyir.com
C8360    Centerfold main motor problem (optional centerfold unit of 3000-sheet document finisher) The motor lock signal is detected above 1 s during driving the centerfold main motor       copyir.com    Poor contact in the connector terminals       copyir.com Defective centerfold main motor       copyir.com Defective PWB       copyir.com
C8440    Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range       copyir.com    The paper entry sensor connector makes poor contact       copyir.com Defective paper entry sensor       copyir.com The optical path of the paper entry sensor is blocked by foreign matter       copyir.com Defective finisher main PWB       copyir.com
C8460    EEPROM problem (optional document finisher) Read and write data does not match 3 times in succession       copyir.com    Defective EEPROM or finisher main PWB       copyir.com
C8500    Mailbox communication error (optional mailbox of 3000-sheet document finisher) Communication with the mailbox is not possible although the connection is detected       copyir.com    Poor contact in the connector terminals       copyir.com Defective PWB       copyir.com
C8510    Mailbox drive motor problem (optional mailbox of 3000-sheet document finisher) The motor lock signal is detected above 500 ms during driving the mailbox drive motor       copyir.com    Poor contact in the connector terminals       copyir.com Defective mailbox drive motor       copyir.com Defective PWB       copyir.com
C8900    Backup memory data problem (optional 3000-sheet document finisher) Read and write data does not match 3 times in succession       copyir.com    Poor contact in the connector terminals       copyir.com Defective finisher main PWB       copyir.com
C8910    Backup memory data problem (optional 3000-sheet document finisher) Read and write data does not match 3 times in succession       copyir.com    Poor contact in the connector terminals       copyir.com Defective punch PWB       copyir.com
C8920    Backup memory data problem (optional mailbox of 3000-sheet document finisher) Read and write data does not match 3 times in succession       copyir.com    Poor contact in the connector terminals       copyir.com Defective mailbox main PWB       copyir.com
C8930    Backup memory data problem (optional centerfold unit of 3000-sheet document finisher) Read and write data does not match 3 times in succession       copyir.com    Poor contact in the connector terminals       copyir.com Defective centerfold main PWB       copyir.com
C9060    EEPROM problem (optional DP) Read and write data does not match       copyir.com    Poor contact in the connector terminals       copyir.com Defective DP drive PWB       copyir.com

خواندن 1294 دفعه

موارد مرتبط

محتوای بیشتر در این بخش: « کیو سرا میتا kmc3225 کیو سرا میتا kmc3225e »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب