شارپ Sharp ARN161G
E1-00 IMC PWB communication trouble
An abnormality occurs in communication between the MCU PWB and the IMC PWB copyir.com IMC PWB-MCU PWB harness abnormality copyir.com
MCU PWB connector disconnection copyir.com
IMC PWB ROM defect/data abnormality
E1-10 IMC PWB trouble
An abnormality occurs in the IMC PWB copyir.com USB chip error/CODEC error on the IMC PWB copyir.com
E1-11 IMC ASIC error
An abnormality occurs in the IMC PWB copyir.com Abnormality in ASIC on the IMC PWB copyir.com
E1-13 IMC PWB flash ROM error
An abnormality occurs in the IMC flash ROM copyir.com IMC PWB abnormality copyir.com
E1-16 IMC PWB DIMM memory read/write check error
An installation error occurs in the IMC expansion compression memory module copyir.com
An error occurs during access to the IMC expansion compression memory copyir.com Improper installation of the IMC expansion memory module copyir.com
IMC expansion memory module abnormality copyir.com
IMC expansion memory contact abnormality copyir.com
IMC PWB abnormality copyir.com
E1-81 Interface error in communication with IMC PWB (Parity)
A parity error occurs in communication between the MCU PWB and the IMC PWB IMC PWB-MCU PWB harness defect copyir.com
Improper connection of the MCU PWB connector copyir.com
IMC PWB ROM defect/data abnormality copyir.com
E1-82 Interface error in communication with IMC PWB (Overrun)
An overrun error occurs in communication between the MCU PWB and the IMC PWB copyir.com IMC PWB-MCU PWB harness defect copyir.com
Improper connection of the MCU PWB connector copyir.com
IMC PWB ROM defect/data abnormality copyir.com
E1-84 Interface error in communication with IMC PWB (Framing)
A framing error occurs in communication between the MCU PWB and the IMC PWB copyir.com IMC PWB-MCU PWB harness defect
Improper connection of the MCU PWB connector copyir.com
IMC PWB ROM defect/data abnormality copyir.com
E7-01 Duplex model memory error
The memory capacity for the duplex model machine is improper copyir.com Insufficient memory capacity copyir.com The memory capacity of the MCU PWB is improper copyir.com
E7-02 LSU trouble
The BD signal from the LSU cannot be detected in a certain cycle copyir.com (Always OFF or always ON) LSU connector or LSU harness defect or disconnection copyir.com
Polygon motor rotation abnormality copyir.com
Laser beams are not generated copyir.com
MCU PWB abnormality copyir.com
E7-10 Shading trouble (Black correction)
The CCD black scan level is abnormal when the shading Improper connection of the CCD unit flat cable
CCD unit abnormality copyir.com
MCU PWB abnormality copyir.com
E7-11 Shading trouble (White correction)
The CCD white scan level is abnormal when the shading copyir.com Improper connection of the CCD unit flat cable
Dirt on the mirror, the lens, and the reference white plate copyir.com
Copy lamp lighting abnormality copyir.com
CCD unit abnormality copyir.com
MCU PWB abnormality(When occurred in the SPF scan position) copyir.com
Improper installation of the mirror unit copyir.com
E7-12 Shading trouble
White correction is not completed in the specified number of operations copyir.com CCD unit flat cable connection failure copyir.com
Dirt on mirrors, lenses, and the reference white plate copyir.com
Copy lamp lighting abnormality copyir.com
CCD unit abnormality copyir.com
MCU PWB abnormality copyir.com
E7-16 Abnormal laser output
When the laser output is stopped, HSYNC is detected copyir.com Laser abnormality copyir.com
MCU PWB abnormality copyir.com
F2-02 Toner supply abnormality
When toner near end is detected with the toner supply time of 50% or less When the toner supply time exceeds 300% copyir.com copyir.com ATC sensor abnormality
Toner supply abnormality
F2-04 Improper cartridge (destination error, life cycle error)
The destination of the machine differs from that of the CRUM copyir.com The life cycle information is other than “Not used (FFh)” copyir.com CRUM chip defect copyir.com
Improper developing unit copyir.com
F2-40 ATC sensor abnormality
ATC sensor value abnormality Connector connection trouble
Toner cartridge installation trouble
Sensor breakdown
F5-02 Copy lamp lighting abnormality
The copy lamp does not turn on copyir.com Copy lamp abnormality copyir.com
Copy lamp harness abnormality copyir.com
CCD PWB harness abnormality copyir.com
F6-00 FAX board communication trouble
FAX board communication error copyir.com No command can be sent from the MCU to the FAX copyir.com
F6-10 FAX board trouble
FAX board abnormality detection copyir.com FAX controller and FAX board memory abnormality copyir.com
F6-80 FAX board communication trouble (Protocol)
A break error occurs in communication between the MCU and the FAX board copyir.com MCU PWB connector connection failure/ Garbled data copyir.com
F6-81 FAX board communication trouble (Parity)
A parity error occurs in communication copyir.com between the MCU and the FAX board copyir.com MCU PWB connector connection failure/ Garbled data copyir.com
F6-82 FAX board communication trouble (Overrun)
An overrun error occurs in communication between the MCU and the FAX board copyir.com MCU PWB connector connection failure/ Garbled data
F6-84 FAX board communication trouble (Framing)
A framing error occurs in communication between the MCU and the FAX board copyir.com MCU PWB connector connection failure/ Garbled data copyir.com
F6-88 FAX board communication trouble (Time out)
FAX board communication error copyir.com There is no respond command from the FAX for 30sec or more copyir.com
F6-97 Combination error between the FAX unit and the main unit
Combination error between the FAX unit and the main unit When this fax unit is installed to the machine that can not install this copyir.com
F6-99 Machine – FAX language error
Discrepancy of the destination of the machine and the FAX board copyir.com The destination of the machine differs from that of the FAX board copyir.com
When installing to the machine that can install only AR-FX11 copyir.com
F9-00 MX-NB10 communication trouble
MX-NB10 print data reception error copyir.com Print data cannot be received from the MX-NB10 for 3 min or more copyir.com
H2-00 Thermistor open
The thermistor is open copyir.com The fusing unit is not installed copyir.com Thermistor abnormality copyir.com
Control PWB abnormality copyir.com
Fusing section connector disconnection copyir.com
The fusing unit is not installed copyir.com
H3-00 Heat roller high temperature detection
The fusing temperature exceeds 240C° copyir.com Thermistor abnormality copyir.com
Control PWB abnormality copyir.com
Fusing section connector disconnection copyir.com
H4-00 Heat roller low temperature detection
When the fusing temperature is lower than 150C° after 55sec from the start of warming up copyir.com
When the warming up complete temperature is not reached in 30sec from reaching 150C° copyir.com
When the fusing temperature is lower than 100C° after 20sec from ready start copyir.com
When the fusing temperature is lower than 145C° when printing copyir.com Thermistor abnormality copyir.com
Heater lamp abnormality copyir.com
Thermostat abnormality copyir.com
Control PWB abnormality copyir.com
H5-01 5-time continuous detections of POUT not-reached jam
Paper not-reached jams are detected 5 times or more continuously by the paper exit sensor (POUT) copyir.com The jam counter is backed up and used for jobs after turning on the power copyir.com A fusing jam is not canceled completely copyir.com (A jam paper remains in the machine copyir.com )
Paper exit sensor trouble or harness connection trouble
Defective installation of the fusing unit copyir.com
L1-00 Scanner feed trouble
The scanner does not complete feeding in the specified time copyir.com Mirror unit abnormality copyir.com
The scanner wire is disconnected copyir.com
The origin detection sensor abnormality copyir.com
Mirror motor harness abnormality copyir.com
L3-00 Scanner return trouble
The scanner does not complete returning in the specified time copyir.com
The mirror is not in the home position when OC copying is started with the mirror standby in the home position copyir.com Mirror unit abnormality copyir.com
Scanner wire disconnection copyir.com
Origin detection sensor abnormality copyir.com
Mirror motor harness abnormality copyir.com
L4-01 Main motor lock detection
The main motor does not rotate copyir.com
The motor lock signal is detected for 1sec or more after rotation of the main motor copyir.com
The motor lock signal is detected for 1sec during rotation of the main motor copyir.com Main motor unit abnormality copyir.com
Improper connection or disconnection the main motor and the harness copyir.com
MCU PWB abnormality copyir.com
L4-11 Shifter motor trouble
The shifter home position detection signal is not detected when initializing the shifter copyir.com Shifter motor abnormality, improper connection or disconnection of the harness, shifter home position sensor abnormality copyir.com
L6-10 Polygon motor lock detection
The polygon motor does not rotate copyir.com
The motor lock signal is detected for 6sec after rotation of the polygon motor copyir.com The motor lock signal is detected for 1sec during rotation of the polygon motor copyir.com Polygon motor unit abnormality
Improper connection or disconnection of the polygon motor and the harness copyir.com
MCU PWB abnormality copyir.com
L8-01 No full wave signal
The zero cross signal is not detected copyir.com Power unit abnormality copyir.com
MCU PWB abnormality copyir.com
U1-03 FAX board battery error
FAX board backup battery error copyir.com The voltage of the backup battery of SRAM which is installed to the FAX board falls below a certain level copyir.com
U2-04 EEPROM read/write error (serial communication error)
EEPROM access process error copyir.com EEPROM abnormality copyir.com
U2-11 Counter check sum error (EEPROM)
Check sum error of the counter area in the EEPROM copyir.com EEPROM abnormality copyir.com
U2-40 CRUM chip communication error
An error occurs during communication between the MCU and the CRUM chip copyir.com CRUM chip abnormality copyir.com
Developing unit disconnection copyir.com
MCU PWB abnormality copyir.com
U9-00 Panel board communication trouble
Communication trouble with the panel board copyir.com No command can be sent from the MCU to the panel copyir.com
U9-80 Panel board communication trouble (Protocol)
An error occurs in communication between MCU -Panel PWB copyir.com MCU PWB – Panel PWB harness trouble/ Garbled data copyir.com
U9-81 Panel board communication trouble (Parity)
A parity error occurs in communication between the MCU and the Panel PWB copyir.com MCU PWB – Panel PWB harness trouble/ Garbled data copyir.com
U9-82 Panel board communication trouble (Overrun)
An overrun error occurs in communication between the MCU and the panel board copyir.com MCU PWB – Panel PWB harness trouble/ Garbled data copyir.com
U9-84 Panel board communication trouble (Framing)
A framing error occurs in communication between the MCU and the Panel PWB copyir.com MCU PWB – Panel PWB harness trouble/ Garbled data copyir.com
U9-88 Panel board communication trouble (Time out)
A time-out error occurs in communication between the MCU and the Panel PWB copyir.com A command is completely sent from the MCU to the panel copyir.com
U9-99 Panel language error
Language discrepancy error copyir.com Discrepancy between the machine language and the panel language copyir.com