Your browser does not support JavaScript! > ریکو آفشیو 1075 | قیمت، خرید، مشخصات و سفارش دستگاه ریکو آفشیو 1075 | کپی ایران

   کانال تلگرام کپی ایران

(0) محصول

ریکو آفشیو 1075

2209 |
بازدید
قیمت: 0 ریال
موجودی انبار: نا محدود

توضیحات مختصر

مخصول مورد نظر منسوخ شده است وبرای خرید پیشنهاد نمی شود شمارهای مشاورین فروش 04137222043-04137252392-04137254200-04137253033-04136586892-04137253034-09120370093-09148659399
سازنده: Rioch

تعداد: 
کاربری لیزری
سرعت چاپ 75 برگ در دقیقه
دقت پیرنت 600Dpi
سطح چاپ A4, A3, A5, B4
سال تولید 2001
کشور سازنده چین, ژاپن, فرانسه, آمریکا
سورتر اختیاری
لارج باکس اختیاری
برد پرینتر اختیاری
فکس ندارد
اسکن به فایل(Scan To File) اختیاری
برد اسکنر تخت
کاربری تک کاره
قابلیت تغذیه خودکار(ADF) اختیاری
حافظه 20 گیگ
قابلیت چاپ دو رو اختیاری
قابلیت کپی دارد
نوع کارتریج نیوب
کارکرد کارتریج مشکی 40000
نوع پورت ارتباطی Ethernet
قابلیت چاپ مستقیم دارد
زمان اسکن 75برگ در دقیقه
اسکن همزمان پشت رو 0

دستگاه استوک به محصولاتی گفته میشود که دوره ۳ الی ۵ ساله استفاده از آنها در کشور های اروپایی و آمریکایی گذشته است. البته مدت زمان استفاده در هرکشورنسبت به قوانین موجود در آن کشور فرق می کند. بر اساس قوانین کشورهای اروپا و آمریکایی دستگاه های استوک باید از رده خارج شوند. سپس دستگاه هایی که کار کرد آنها کم باشد و قابل بازسازی باشند به کشورهای آسیایی و جهان سوم واگذار می شوند. این دستگاه ها پس از جنرال سرویس کاملا قابل استفاده می باشد. به این دستگاه ها، اصطلاحا استوک گفته می شود.

دستگاه استوک بر دو نوع می باشد

  1. استوک سرویس شده
  2. استوک بازسازی شده

دستگاه استوک سرویس شده

دستگاه های که برروی لیست استوک قرار می گیرند. کنترول و رفع ایراد می شوند و سپس برای خریداران ارائه می گردند.

دستگاه استوک باسازی شده

دستگاه های که بر روی لیست استوک قرار می گیرند بعد از سرویس و کنترل نهایی تمامی مواد مصرفی دستگاه با مواد مصرفی آکبند جایگزین می شوند. این مواد در دستگاهای فتوکپی شامل تونر، هیتر کامل، ترانسفر و ایمیجها که همان یونیت دارم می باشد و در دستگاهای ریسو گراف شامل سیلندر و در دستگاهای پلاتر شامل هد، نوار اینکودر و اینک ساکریشین و کارتریج مرکب می باشد. دستگاه های استوک باسازی شده کیفیت بسیار بالایی از نظر کیفیت کار و مدت زمان استفاده دستگاه نسبت به استوک های معمولی دارند و همسان دستگاه آکبند می باشند.

منظور از دستگاه استوک بازسازی شده چیست؟

یک دستگاه استوک معمولی ممکن است دارای ایراداتی باشد. در این شرایط قطعات دستگاه تعویض می شوندو دستگاه کیفیتی به مانند آکبند را خواهد داشت. دستگاه استوک بازسازی شده نسبت به دستگاه آکبند هزینه ای بسیار پایین تری خواهد داشت و مقرون به صرفه تر است. در زمان خرید دستگاه استوک چندین مورد دارای اهمیت هستند: ۱- پایین بودن کنتور دستگاه (همان کارکرد) ۲- مواد مصرفی دستگاه. ۳-تاریخ تولید دستگاه (از تاریخ تولید دستگاه بیش از سه سال نگذرد.) ۵- ضمانت نامه خرید 6- نصب وراه اندازی دستگاه توسط متخصصین شرکت خریداری شده.

قیمت دستگاه استوک

قیمت گذاری دستگاه استوک با توجه به کیفیت و شرایط دستگاه تعیین میشود. هر چه دستگاه کارکرد کمتری داشته باشد و شرایط آن بهتر باشد، طبیعتا قیمت بالاتری خواهد داشت. بنابراین دستگاه استوک با مدل و مارک مشخص با توجه به وضعیت دستگاه دارای قیمت های متفاوتی خواهد بود. در زمان خرید دستگاه های استوک توجه داشته باشید هرچه قطعات اصلی در حالت بهتری قرار داشته باشند کیفیت بالاتری را شاهد خواهید بود.

دستگاه آکبند چیست؟

دستگاه آکبند به محصولاتی گفته می شود که تا کنون مورد استفاده قرار نگرفته باشند و اصطلاحا نو باشند. این دستگاه ها به نسبت دستگاه استوک از قیمت بالاتری برخوردار هستند و زمان زیادی از تولید آنها نگذشته است.اگر مشکل نقدینگی نداشته باشیدحتما  اولویت خرید دستگاه آکبند می باشد .

دستگاه استوک بخریم و یا آکبند بخریم ؟

دستگاه های استوک بازسازی شده نسبت به دستگاه های آکبند از قیمت بسیار مناسبتری برخوردار هستند و در زمان بازسازی کیفیت آنها به مانند دستگاه آکبند می باشد، لذا بسیار مقرون به صرفه تر هستند. می توانید با هزینه ای بسیار پایین تر این محصولات را خریداری کرده و با همان کیفیت آکبند استفاده کنید. دستگاه استوک باسازی شده را تنها ازشرکتهای معتبر تهیه فرمایید.

از آنجایی که کیفیت و شرایط محصول در زمان خرید یک دستگاه استوک بسیار مهم است، باید آنرا از فروشنده معتبر تهیه کنید. کپی ایران با سابقه ای طولانی در فروش و ارائه خدمات، ضمانت کیفیت برای کلیه محصولات فروخته شده ارائه می کند. لذا می توانید از تناسب کیفیت و قیمت محصول اطمینان کامل را داشته باشید. ما پس از بررسی و تست کامل بر روی دستگاه، آن را به مشتریان محترم ارائه می کنیم. این تست و بررسی با رعایت بالاترین استاندارد ها صورت می گیرد، لذا می توانید یک خرید مطمئن و با هزینه مناسب را تجربه کنید.

نظرات

تضمین بهترین قیمت
 
تضمین بهترین قیمت چیست؟

ما تضمین می‌کنیم محصولات عرضه شده در کپی ایران با گارانتی اصل، بالاترین کیفیت و ارزان‌ترین قیمت نسبت به سایر فروشگاه‌های فیزیکی و اینترنتی در سراسر کشور است. اگر پس از خرید از کپی ایران، متوجه شدید فروشگاهی همان کالا را با شرایط یکسان و قیمتی پایین‌تر ارائه می‌دهد، می‌توانید درخواست استفاده از «تضمین بهترین قیمت» را ارسال و در صورت تایید، اختلاف قیمت آن را به طور کامل از ما دریافت کنید.
چه شرایطی دارد؟

برای ارائه درخواست تضمین بهترین قیمت باید شرایط زیر وجود داشته باشد:

    مدل یکسان: محصولات باید از نظر ویژگی‌های فنی، رنگ، امکانات و قابلیت‌ها یکسان باشند.
    کالای اصل: از آنجایی که همه کالاهای موجود در کپی ایران اصل هستند، درخواست کالاهای غیر اصل رد خواهد شد.

3. گارانتی اصل و یکسان: کالاهای مورد مقایسه باید گارانتی و خدمات پس از فروش اصل و یکسان داشته باشند، زیرا نوع و کیفیت خدمات گارانتی‌های مختلف بر قیمت آنها نیز تاثیر می‌گذارد.

    لوازم جانبی اصلی در بسته‌بندی کارخانه: کپی ایران همه لوازم و قطعات همراه کالا که از طرف شرکت سازنده ارائه می‌شود را بدون تغییر یا کم و کاستی به مشتری تحویل می‌دهد. بنابراین محصولاتی که در سایر فروشگاه‌ها ارائه می‌شوند، در صورتی امکان مقایسه خواهند داشت که لوازم جانبی و قطعات اصل و با کیفیت به همراه داشته باشند.

5. یکسانی شرایط برای کالاهایی که دارای تاریخ تولید یا انقضا هستند، شامل تاریخ مصرف نیز می‌شود.

    فروشگاه‌ها و وب‌سایت‌های مجاز: مرجع مقایسه قیمت باید فروشگاه مجاز و وب‌سایت دارای نماد اعتماد الکترونیک از وزارت صنعت معدن و تجارت باشد.
    کالا برای فروش موجود باشد: کالا باید در زمان ارائه درخواست به کپی ایران در سایت یا فروشگاه موردنظر برای فروش موجود و قابل خریداری باشد.

8. با توجه به رسمی بودن فاکتورهای کپی ایران، فاکتور فروشگاه فیزیکی یا اینترنتی مورد مقایسه نیز باید رسمی و دارای کد اقتصادی و 9% مالیات بر ارزش افزوده باشد.

9. با توجه به لزوم یکسان بودن شرایط مقایسه، اگر لحاظ کردن مواردی مانند هزینه حمل و نقل یا مالیات بر ارزش افزوده، قیمت اولیه اعلام شده توسط فروشنده یا فروشگاه اینترنتی مورد مقایسه را تغییر دهد، ملاک مقایسه قیمت کپی ایران، مبلغ نهایی پرداخت شده توسط خریدار خواهد بود.

10.درمورددستگاهای استوک ملاک شرایط مذبور می باشد .

1.مدل دستگاه

2.آپشن های مورد نظر

3.کارکرد دستگاه یعنی دارای شناسنامه باشد که دستگاه مذبور در کجا کار کرده وچه قطعاتی در چه کارکردی تعویض شده است

4.زمان فروش مواد مصرفی آکبند برای شما تحویل داده شده است یا خیر

چگونه درخواست بفرستید؟

مدارک زیر را همراه فاکتور خود، به آدرس ایمیل www.copyir@yahoo.comارسال کنید:

1. پیش‌فاکتور فروشگاه به صورت عکس یا فایل اسکن شده؛ پیش فاکتور باید:

- شامل نام فروشگاه، اطلاعات تماس، آدرس و مهر فروشگاه، نام خریدار، تاریخ و مدت اعتبار پیش فاکتور، اطلاعات محصول و نام گارانتی مربوط به آن باشد.

- تا 24 ساعت بعد از زمان ارسال ایمیل توسط مشتری دارای اعتبار  و کالا در آن فروشگاه موجود و قابل خریداری باشد.

- صرفا برای همان محصول به صورت تکی باشد.

2. در فروشگاه‌های اینترنتی، کافی‌ست آدرس فروشگاه اینترنتی و لینک مستقیم صفحه کالای مورد مقایسه به آدرس ایمیل ذکر شده ارسال شود. بدیهی است که اگر به وب سایت‌های مرجع مقایسه قیمت لینک داده شود، ایمیل ارسالی قابل بررسی نخواهد بود.

چه زمانی درخواست بفرستید؟

درخواست مشتری باید حداکثر تا 48 ساعت بعد از فاکتور شدن سفارش، ارسال شود.

بررسی ثبت درخواست تا حداکثر 3 روز کاری انجام می‌شود.

پس از ارسال استعلام و در صورت تایید قیمت پایین‌تر، اضافه مبلغ پرداخت شده را به حساب شخص واریز می‌کنیم.

سوال دارید؟

با شماره تلفن 04137253034 – داخلی 8 (خدمات پس از فروش) تماس بگیرید.
 
قوانین

در صورت مشاهده تخلف یا تلاش برای سوءاستفاده از این طرح، حق عدم پذیرش آن درخواست برای کپی ایران محفوظ است.

کپی ایران می‌تواند در هر زمان به تشخیص خود شرایط تضمین بهترین قیمت را تغییر داده و یا ارائه آن را متوقف کند

 

ایرادات فتوکپی ریکو آفشیو 1070  بر اساس کد می باشد ما برا ی سهولت کار بران تمامی کدهای را در اختیار عزیزان قرار می دهیم

101    Exposure Lamp Error
At trigger on, the lamp was not detected on  copyir.com     • Exposure lamp defective
• Lamp regulator defective
• Lamp regulator harness damaged, disconnected
• Dirty standard white plate
• Scanner mirror dirty or out of position
• Lens dirty, out of position
• SBU board defective
120    Scanner home position error 1
The scanner HP sensor does not detect the on condition during initialization or copying  copyir.com     • BCU, SDRB (Scanner Driver Board) defective
• Scanner motor defective
• Harness between BCU, SDRB, scanner motor disconnected  copyir.com
• Scanner HP sensor defective  copyir.com
• Harness between scanner HP sensor and BCU disconnected  copyir.com
• Scanner wire, timing belt, pulley, carriage installed incorrectly  copyir.com
121    Scanner home position error 2
The scanner HP sensor does not detect the off condition during initialization or copying  copyir.com     • BCU, SDRB (Scanner Driver Board) defective
• Scanner motor defective
• Harness between BCU, SDRB, scanner motor disconnected
• Scanner HP sensor defective
• Harness between scanner HP sensor and BCU disconnected
• Scanner wire, timing belt, pulley, carriage installed incorrectly  copyir.com
122    Scanner home position error 3
The scanner home position sensor does not detect the on condition during original scanning  copyir.com     • BCU, SDRB (Scanner Driver Board) defective
• Scanner motor defective
• Harness between BCU, SDRB, scanner motor disconnected
• Scanner HP sensor defective
• Harness between scanner HP sensor and BCU disconnected
• Scanner wire, timing belt, pulley, carriage installed incorrectly
123    Scanner home position error 4
The scanner home position sensor does not detect the off condition during original scanning  copyir.com     • BCU, SDRB (Scanner Driver Board) defective
• Scanner motor defective
• Harness between BCU, SDRB, scanner motor disconnected
• Scanner HP sensor defective
• Harness between scanner HP sensor and BCU disconnected
• Scanner wire, timing belt, pulley, carriage installed incorrectly  copyir.com
143    SBU auto adjust error
Automatic adjustment of the SBU fails when the machine is switched on  copyir.com     • Exposure lamp defective
• Exposure lamp regulator defective
• Harness between exposure lamp and lamp regulator is disconnected
• White plate installed incorrectly or is dirty
• Scanning mirrors of the exposure unit are dirty or out of position
• SBU board defective
• VIB board defective  copyir.com
• Harness between SBU, VIB disconnected
• Harness between VIB, BCU disconnected
144    SBU transmission error
After the SBU switches on, the BCU detects one of the following conditions on the SBU:
• 1 s after power on, the SYDI signal does not go high, even after 1 retry  copyir.com
• 1 s after power on, the SYDI signal goes high, but the SBU ID could not be read after 3 attempts  copyir.com     • SBU defective
• VIB defective
• Harness (40-pin shielded) between the SBU, VIB is disconnected
• Harness (shielded cable) between the VIB, BCU is disconnected
165    Copy data security unit error B828
The copy data security option is installed by not operating correctly  copyir.com     • Copy data security card corrupted
• The board is not installed or the board is defective
• IPU board defective
181    CIS lamp abnormal
After the CIS lamp trigger goes on, the CIS lamp is not detected on  copyir.com  Detecting the lamp on or off determines the peak white level value for shading correction  copyir.com  (If the peak level is determined to be below a certain level, the CIS lamp is judged to be off  copyir.com )    • CIS lamp defective
• CIS power supply board defective
• CIS lamp regulator defective
• Harness between lamp and lamp regulator is disconnected  copyir.com
• Harness between CIS, ADF is disconnected
• CIS exposure glass dirty  copyir.com
• White roller dirty or installed incorrectly
• CIS unit defective
183    CIS auto adjust error
Automatic adjustment of the CIS unit failed  copyir.com     • CIS unit defective
• CIS exposure glass dirty
• White roller dirty or installed incorrectly
184    CIS transmission error
When the CIS is powered on, the ADF detects one of the following abnormal conditions on the CIS unit:
• The SOUT signal does not go high within 1 s after power on  copyir.com  
• The SOUT signal goes high within 1 s after power on, but the SBU ID cannot be read after 3 attempts  copyir.com     • CIS unit defective
• Harness between the CIS, ADF is disconnected
202    Polygon mirror motor error 1: Timeout at ON
The polygon mirror motor unit did not enter "Ready" status within 20 sec  copyir.com  after the motor was turned on, or within 20 sec  copyir.com  after the speed of rotation was changed  copyir.com     • The polygon mirror motor PCB connector is loose, broken, or defective
• Polygon mirror motor PCB defective
• Polygon mirror motor defective
• IPU defective
203    Polygon mirror motor error 2: Timeout at OFF
The polygon mirror motor did not leave "Ready" within 3 sec  copyir.com  after the motor was switched off  copyir.com  (The XSCRDY signal did not go HIGH (inactive) within 3 sec  copyir.com )    • The polygon mirror motor PCB connector is loose, broken, or defective
• Polygon mirror motor PCB defective
• Polygon mirror motor defective
• IPU defective
204    Polygon mirror motor error 3: XSCRDY signal error
The polygon mirror motor "Ready" signal went inactive (HIGH) while the motor was operating at normal speed, even though the motor was neither switched off nor was there a request for a change in speed  copyir.com     • Electrical oise interference on the line with the motor signals
• Polygon mirror motor PCB connector loose, broken, defective
• Polygon mirror motor PCB defective
• Polygon mirror motor defective
205    Polygon mirror motor error 4: Unstable timeout
The "Ready" signal (XSCRDY) was detected as unstable for more than 20 sec  copyir.com  while the polygon mirror motor was operating at normal speed  copyir.com     • Electrical noise on the line with the motor signals
• Polygon mirror motor PCB connector loose, broken, defective
• Polygon mirror motor PCB defective
• IPU defective
220    Laser synchronization detection error
The 1st laser synchronization detection unit could not detect the line synchronization signal (DETP0) within 500 ms while the polygon mirror motor was operating at normal speed  copyir.com  Note: The unit polls for the signal every 50 ms  copyir.com  This SC is issued after the 10th attempt fails to detect the signal  copyir.com     • Laser synchronization board connector loose, broken, defective
• Laser synchronization detection board is not installed correctly (out of alignment)
• Laser synchronization board defective • IPU defective
300    Charge corona output error
The feedback voltage from the charge corona unit is detected too high 9 times    • Charge corona power pack defective
• Charge corona harness disconnected
• Poor charge corona unit connection
303    Charge corona grid leak
When the high voltage is output to the corona grid, feedback voltage exceeds the prescribed value 9 times  copyir.com     • Charge corona power pack defective
• Charge corona harness disconnected • Poor charge corona unit connection
304    Charge grid circuit open
When high voltage goes to the corona grid, feedback voltage is more than the set value 9 times  copyir.com  This feedback voltage is used to update PWM for output control  copyir.com     • Charge corona unit defective or disconnected
• Charge corona harness defective
• Charge corona power pack is defective  copyir.com
305    Charge corona wire cleaner error 1
The charge cleaner pad does not arrive at the home position:
• Motor locked within 4 s after switching on, or does not lock within 30 s  copyir.com  
• Motor locked within 10 s after reversing, or does not lock within 30 s  copyir.com     • Charge corona wire cleaner motor defective
• Motor driver defective
306    Charge corona wire cleaner error 2
Charge coronal motor is disconnected  copyir.com  (The current at the charge corona motor is detected less than 83 mA  copyir.com )    • Charge corona wire cleaner motor connector is defective, connected
310    Potential sensor calibration error 1
During drum potential sensor calibration, the drum potential sensor output voltage does not meet specification when test voltages (– 100V, –800V) are applied to the drum  copyir.com     • Potential sensor defective
• Potential sensor harness disconnected
• Potential sensor connector defective or disconnected
• IOB defective
• OPC connector defective
• Development power pack defecti
311    Potential sensor calibration error 2
During drum potential sensor calibration, the drum potential sensor output voltage does not meet specification when test voltages (– 100V, –800V) are applied to the drum  copyir.com     • Potential sensor defective
• Potential sensor harness disconnected
• Potential sensor connector defective or disconnected
• IOB defective
• OPC connector defective
• Development power pack defective
312    Potential sensor calibration error 3
During drum potential sensor calibration when adjusting the drum potential (VD), the drum potential sensor detects VD higher than VG (grid voltage)  copyir.com  -or- When adjusting VD (drum surface potential of black areas after exposure), even after 5 adjustments of VG (charge corona grid potential), VD could not be set in the target range (– 800±10 + VL + 130V)    • Potential sensor defective
• Potential sensor harness disconnected
• Potential sensor connector defective or disconnected
• IOB defective
• OPC connector defective
• Development power pack defective
• Charge corona unit worn out, dirty
314    Potential sensor calibration error 4
During drum potential sensor calibration when adjusting the drum potential (VH) for LD power adjustment, the first time the VH pattern is made, the drum potential sensor detects that VH is more than 500V: VH > |–500 + VL + 130| V    • Potential sensor defective
• Potential sensor harness disconnected
• Potential sensor connector defective or disconnected
• IOB defective
• OPC connector defective
• LD defective
315    Potential sensor calibration error 5
During drum potential sensor calibration, when –100V is applied to the drum, the output value is out of the prescribed range    • Potential sensor defective
• Potential sensor harness disconnected
• Potential sensor connector defective or disconnected
• IOB defective
• OPC connector defective
• Development power pack defectiv
316    Potential sensor calibration error 6
During drum potential sensor calibration, when –800V is applied to the drum, the output value is out of the prescribed range  copyir.com     • Potential sensor defective
• Potential sensor harness disconnected
• Potential sensor connector defective or disconnected
• IOB defective
• OPC connector defective
• Development power pack defective
317    Potential sensor calibration error 7
During drum potential sensor calibration, when VL is adjusted, the pattern surface potential VL pattern is not within range 0V ~ –400V  copyir.com  (VL is the potential after exposing a white pattern  copyir.com )    • Potential sensor defective
• Potential sensor harness disconnected
• Potential sensor connector defective or disconnected
• IOB defective
• OPC connector defective
• Charge corona power pack defective
• Development power pack defective
321    F-GATE error
The laser writing signal (F-GATE) for the IPU does not go LOW within 60 s  copyir.com     • BICU board defective
• PCI bus between controller board, BICU board defective
322    Laser synchronization detector error
After the polygon motor reaches standard rotation speed and the LD unit fires for 500 ms, the laser synchronization detector does not generate a signal    • Harness between detector and I/F disconnected or damaged
• Detector is installed incorrectly
• Detector board is defective
• IPU board defective
335    Polygon mirror motor error 1
The ready signal does not go low within 20 s after the polygon mirror motor turns on or changes speed  copyir.com     • Harness between I/F and polygon motor disconnected or defective
• Polygon motor or polygon motor driver defective
• IPU board defective
336    Polygon mirror motor error 2
The ready signal does not go high within 20 s after the polygonal mirror motor turns off  copyir.com     • Harness between I/F and polygon motor disconnected or defective
• Polygon motor or polygon motor driver defective
• IPU board defective
337    Polygonal mirror motor error 3
The XSCRDY signal goes high while the polygon mirror motor turns on, even though there was no request to either turn off the motor or change the motor speed  copyir.com     • Noise on the line where the polygon ready signal (XSCRDY) is transmitted  copyir.com  
• Harness between the polygon motor and I/F disconnected or defective  copyir.com  
• Polygon motor or polygon motor driver defective
338    Polygonal mirror motor error 4
While the polygon motor is rotating, the XSCRDY signal goes high during exposure    • Noise on the linef where the polygon ready signal (XSCRDY) is transmitted  copyir.com  
• Harness between the polygon motor and I/F disconnected or defective  copyir.com  
• Polygon motor or polygon motor driver defective
• IPU board defective
340    TD sensor output error
TD sensor output voltage (Vt), measured during each copy cycle, is detected 10 times at one of the following levels: Vt = 0  copyir.com 5 volts or lower Vt = 4  copyir.com 0 volts or higher    • TD sensor defective
• TD sensor harness disconnected
• TD sensor connector disconnected or defective
• IOB defective
• Toner bottle motor defective Note: When the TD sensor is defective, the toner supply is controlled using pixel count and the ID sensor  copyir.com
341    TD sensor adjustment error 1
During the TD sensor auto adjustment, the TD sensor output voltage (Vt) is 2  copyir.com 5 volts or higher even though the control voltage is set to the minimum value (PWM = 0)  copyir.com  When this error occurs, SP2-906-1 reads 0  copyir.com 00V  copyir.com  Note: This SC is released only after correct adjustment of the TD sensor has been achieved  copyir.com  Switching the machine off and on will cancel the SC display, but does not release ID sensor toner supply  copyir.com     • TD sensor defective
• TD sensor harness disconnected
• TD sensor connector disconnected or defective
• IOB defective
• Toner bottle motor defective Note: When the TD sensor is defective, the toner supply is controlled using pixel count and the ID sensor  copyir.com
342    TD sensor adjustment error 2
During the TD sensor auto adjustment, the TD sensor output voltage (Vt) does not enter the target range (3  copyir.com 0 ± 0  copyir.com 1V) within 20 s  copyir.com  When this error occurs, the display of SP2-906-1 reads 0  copyir.com 00V  copyir.com  Note: This SC is released only after correct adjustment of the TD sensor has been achieved  copyir.com  Switching the machine off and on will cancel the SC display, but does not release ID sensor toner supply  copyir.com     • TD sensor defective
• TD sensor harness disconnected
• TD sensor connector disconnected or defective
• IOB defective
345    Development output abnormal
The high voltage applied to the development unit is detected 10 times higher than the upper limit (45%) of PWM  copyir.com     • Development power pack defective
• Development bias leak due to poor connection, defective connector
350    ID sensor error 1
One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern  copyir.com  Vsp   copyir.com  2  copyir.com 5V Vsg < 2  copyir.com 5 Vsp = 0V Vsg = 0    • ID sensor defective
• ID sensor harness disconnected
• ID sensor connector defective
• IOB defective
• ID sensor pattern not written correctly
• Incorrect image density
• Charge power pack defective
• ID sensor dirty
351    ID sensor error 2
The ID sensor output voltage is 5  copyir.com 0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern  copyir.com     • ID sensor defective
• ID sensor harness disconnected
• ID sensor connector defective • IOB defective
• ID sensor pattern not written correctly
• Incorrect image density
• Charge power pack defective
• ID sensor dirty
352    ID sensor error 3
For 2 s during the ID sensor pattern check, the ID sensor pattern edge voltage is not 2  copyir.com 5V or the pattern edge is not detected within 800 ms  copyir.com     • ID sensor defective
• ID sensor harness disconnected
• ID sensor connector defective
• IOB defective
• ID sensor pattern not written correctly
• Incorrect image density
• Charge power pack defective
• ID sensor dirty
353    ID sensor error 4
One of the following ID sensor output voltages is detected at ID sensor initialization  copyir.com    copyir.com  Vsg < 4  copyir.com 0V when the maximum PWM input (255) is applied to the ID sensor  copyir.com    copyir.com  Vsg   copyir.com  4  copyir.com 0V when the minimum PWM input (0) is applied to the ID sensor  copyir.com     • ID sensor defective
• ID sensor harness disconnected
• ID sensor connector defective
• IOB defective
• ID sensor pattern not written correctly
• Incorrect image density
• Charge power pack defective
• ID sensor dirty
354    ID sensor error 5
Vsg falls out of the adjustment target (4  copyir.com 0 ± 0  copyir.com 2V) during Vsg checking    • ID sensor defective
• ID sensor harness disconnected
• ID sensor connector defective
• IOB defective
• ID sensor pattern not written correctly
• Incorrect image density
• Charge power pack defective
• ID sensor dirty
355    ID sensor error 6
The Vp value, which measures the reflectivity of the ID sensor pattern, was not in the range of –70V to –400V  copyir.com     • Potential sensor defective
• Potential sensor harness defective
• Potential sensor disconnected
• IOB defective
• OPC unit connector defective
• Charge corona power pack defective
• Charge corona wire dirty, broken
401    Transfer output abnormal
When the transfer is output, the feedback voltage remains higher than 4V for 60 ms  copyir.com     • Transfer power pack defective
• Transfer current terminal, transfer power pack disconnected, damaged connector
402    Transfer output abnormal release detection
When the transfer is output, there is hardly any feedback voltage within 60 ms even with application of 24% PWM  copyir.com     • Transfer power pack defective
• Transfer unit harness disconnected
• Transfer connector loose, defective
430    Quenching lamp error
At the completion of auto process control initialization, the potential of the drum surface detected by the potential sensor is more than –400V, the prescribed value  copyir.com     • Quenching lamp defective
• Quenching lamp harness disconnected
• Quenching lamp connector loose,
defective
440    Main motor lock
The main motor lock signal remains low for 2 seconds while the main motor is on  copyir.com     • Drive mechanism overloaded
• Motor driver board defective
441    Development motor lock
The development motor lock signal remains high for 2 seconds while the development motor is on  copyir.com     • Drive mechanism overloaded due to toner clumping in the wasted toner path
• Motor driver board defective
490    Main fan error
The main fan motor lock signal goes high for 5 s while the fan is on  copyir.com     • Fan motor overloaded due to obstruction
• Fan connector disconnected
495    Toner recycling unit error
Encoder pulse does not change for 3 s after the main motor switches on  copyir.com     • Waste toner transport has stopped due to motor overload
• Toner end sensor detective, disconnected
496    Toner collection bottle errorThe toner collection bottle set switch remains off when the front door is closed  copyir.com     • No toner collection bottle set
• Poor connection of the switch connector
497    Toner collection motor error
The toner collection motor connector set signal remains off for 1 s  copyir.com     • Toner pump motor defective
• Motor connector loose, disconnected
501    Tray 1 lift malfunction
• The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate  copyir.com  
• When the tray lowers, the tray lift sensor does not go off within 1  copyir.com 5 sec  copyir.com  
• Tray overload detected when the tray is set  copyir.com  
• The lower limit sensor of the LCT does not detect the lower limit within 10 sec  copyir.com     • Tray lift motor defective, disconnected
• Paper or other obstacle trapped between tray and motor
• Pick-up solenoid disconnected, blocked by an obstacle
• Too much paper loaded in tray Note (B246)
• At first, the machine displays a message asking the operator to reset the tray  copyir.com  
• This SC will not display until the operator has pulled the tray out and pushed it in 3 times  copyir.com  
• If the operator cycles the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset  copyir.com
502    Tray 2 lift malfunction
• The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate  copyir.com  
• When the tray lowers, the tray lift sensor does not go off within 1  copyir.com 5 sec  copyir.com  
• Tray overload detected when the tray is set  copyir.com     • Tray lift motor defective or disconnected
• Paper or other obstacle trapped between tray and motor
• Pick-up solenoid disconnected or blocked by an obstacle
• Too much paper loaded in tray Note (B246)
• At first, the machine displays a message asking the operator to reset the tray  copyir.com  
• This SC will not display until the operator has pulled the tray out and pushed it in 3 times  copyir.com  
• If the operator cycles the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset  copyir.com
503    Tray 3 lift malfunction
• The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate  copyir.com  
• When the tray lowers, the tray lift sensor does not go off within 1  copyir.com 5 sec  copyir.com  
• Tray overload detected when the tray is set  copyir.com     • Tray lift motor defective or disconnected
• Paper or other obstacle trapped between tray and motor
• Pick-up solenoid disconnected or blocked by an obstacle
• Too much paper loaded in tray Note (B246)
• At first, the machine displays a message asking the operator to reset the tray  copyir.com  
• This SC will not display until the operator has pulled the tray out and pushed it in 3 times  copyir.com  
• If the operator cycles the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset  copyir.com
504    Tray 4 lift malfunction
• The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate  copyir.com  
• When the tray lowers, the tray lift sensor does not go off within 1  copyir.com 5 sec  copyir.com  
• Tray overload detected when the tray is set    • Tray lift motor defective or disconnected
• Paper or other obstacle trapped between tray and motor
• Pick-up solenoid disconnected or blocked by an obstacle
• Too much paper loaded in tray Note (B246)
• At first, the machine displays a message asking the operator to reset the tray  copyir.com  
• This SC will not display until the operator has pulled the tray out and pushed it in 3 times  copyir.com  
• If the operator cycles the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset  copyir.com
507    LCT feed motor malfunction
One of the following conditions is detected:
• The LD signal from the feed motor is detected abnormal for 50 ms after the motor switches on  copyir.com  
• At power on, the motor is detected loose or disconnected    • Feed motor defective
• Feed motor connector disconnected
• Obstacle interfering with mechanical movement of motor  copyir.com
510    LCT tray malfunction
One of the following conditions is detected:
• When the bottom plate is lifted, the upper limit sensor does not come on for 18 s  copyir.com  
• When the bottom plate is lowered, the lower limit sensor does not come on for 18 s  copyir.com  
• After lift begins, the upper limit sensor does not switch on before the pick-up solenoid switches on  copyir.com  
• The paper end sensor switches on during lift and the upper limit sensor does not switch on for 2  copyir.com 5 s, and a message prompts user to reset paper  copyir.com     • Tray lift motor defective or connector disconnected
• Lift sensor defective or disconnected
• Pick-up solenoid defective or disconnected
• Paper end sensor defective
515    Tandem rear fence motor error
One of the conditions is detected:
• The return sensor does not switch on within 10 sec  copyir.com  after the rear fence motor switches on  copyir.com  
• The HP sensor does not switch on 10 sec  copyir.com  after the rear fence motor switches on  copyir.com  
• The HP sensor and return sensor switch on at the same time  copyir.com     • Rear fence motor defective or poor connection
• Paper or other obstacle interfering with operation of the sensors
• Paper or other obstacle trapped between tray and motor
• Motor mechanical overload due to obstruction
• Return sensor or HP sensor defective or dirty Note (B246)
• This problem will not issue the SC code on the operation panel  copyir.com  
• The machine will prompt the operator to reset tray by opening and closing it  copyir.com  
• If the problem persists, the machine will display again and the tray cannot be used  copyir.com
520    Duplex jogger motor error 1
When the jogger fence moves to the home position, the jogger HP sensor does not turn on even if the jogger fence motor has moved the jogger fence 153  copyir.com 5 mm    • Paper or other obstacle has jammed mechanism
• Sensor connector disconnected or defective
• Sensor defective
521    Duplex jogger motor error 2
When the jogger fence moves from the home position, the jogger fence HP sensor does not turn off even if the jogger motor has moved the jogger fence 153  copyir.com 5 mm  copyir.com     • Paper or other obstacle has jammed mechanism
• Sensor connector disconnected or defective
• Sensor defective
531    Fusing exit motor error
The PLL lock signal was low for 2 seconds during motor operation  copyir.com     • Motor lock caused by physical overload
• Motor drive PCB defective
541    Fusing thermistor open
The fusing temperature detected by the center thermistor was below 0°C for 7 sec  copyir.com     • Thermistor open
• Thermistor connector defective
• Thermistor damaged, or out of position
• Fusing temperature –15% less than the standard input voltage
542    Fusing temperature warm-up error
One of the following occurred:
• After power on, or after closing the front door, the hot roller does not reach the 100°C control temperature within 25 s  copyir.com  
• 5 sec  copyir.com  after temperature rise started, temperature remained below 21°C after 5 samplings  copyir.com  
• Fusing unit did not attain reload temperature within 48 sec  copyir.com  of the start of fusing temperature control  copyir.com     • Fusing lamp disconnected
• Thermistor warped, out of position
• Thermostat not operating
543    Fusing lamp overheat error 1 (software)
Central thermistor detected a temperature of 240°C at the center of the hot roller  copyir.com  Fusing temperature control software error    • PSU defective
• IOB defective
• BICU defective
544    Fusing lamp overheat error 1 (hardware)
The central thermistor or an end thermistor detected a temperature of 250°C on the hot roller  copyir.com     • PSU defective
• IOB defective
• BICU defective
545    Fusing lamp overheat error 2
After hot roller reaches warmup temperature, the fusing lamps remained on at full capacity for 11 samplings (1  copyir.com 8 sec  copyir.com  duration) while the hot roller was not rotating  copyir.com     • Thermistor damaged, or out of position
• Fusing lamp disconnected
547    Zero cross signal malfunction
One of the following conditions is detected 10 times:
• When the main switch is on, the frequency measured by the number of zero cross signals for 500 ms is larger than 66Hz or smaller than 45 Hz  copyir.com  
• The interval between one zero cross signal and the next is 7  copyir.com 5 ms or shorter 3 times consecutively for 500 ms  copyir.com     • Noise on the ac power line
550    Fusing Web End
Web end detected 5 times within 500 ms and web motor continues to rotate 40 s  copyir.com  If web end is detected for another 500 ms, then the SC is logged  copyir.com     • Web end (requires replacement)
• Web end sensor defective Note: After replacing the web with a new one, reset SP1902 001 to "0" to release SC550  copyir.com
551    Fusing thermistor error 1
The end thermistor (contact type) was less than 0C (32F) for more than 7 seconds  copyir.com     • Thermistor disconnected
• Thermistor connector defective
552    Fusing thermistor error 2
The end thermistor (contact type) could not detect:
• 100°C 25 seconds after the start of the warmup cycle  copyir.com  
• A change in temperature more than than 16 degrees for 5 seconds  copyir.com  
• The reload temperature with 56 seconds after the start of the fusing temperature control cycle  copyir.com     • Fusing lamp disconnected
• Thermistor bent, damaged
• Thermistor position incorrect
553    Fusing thermistor error 3
The end thermistor (contact type) was at 240°C (464°F) for more than 1 second  copyir.com  The temperature is read 10 times every sec  copyir.com  (at 0  copyir.com 1 sec  copyir.com  intervals)  copyir.com     • PSU defective
• IOB control board defective
• BICU control board defective
555    Fusing lamp error
After the start of the warmup cycle, a fusing lamp was at full power for 1  copyir.com 8 seconds but the hot roller did not turn  copyir.com     • Thermistor bent, out of position
• Fusing lamp disconnected
• Circuit breaker opened
557    Zero cross signal error
High frequency noise was detected on the power line  copyir.com     • No action required  copyir.com  The SC code is logged and the operation of the machine is not affected  copyir.com
559    Fusing jam: 3 counts
At the fusing exit sensor the paper was detected late for three pulse counts (lag error), and SP1159 was on  copyir.com     This SC only occurs if SP1159 is on, and a jam occurred in the fusing unit for three consecutive sheets of paper  copyir.com  Remove the paper that is jammed in the fusing unit  copyir.com  Then make sure that the fusing unit is clean and has no obstacles in the paper feed path  copyir.com
569    Fusing pressure release motor error
During copying, the HP sensor could not detect the actuator, tried again 3 times and could not detect  copyir.com     • Motor lock because of too much load
• Motor driver defective
• HP sensor defective, disconnected, connector defective, harness damaged
590    Toner collection motor error
The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on  copyir.com     • Motor lock due to obstruction
• Motor driver board defective
• Motor connection loose, defective
• Toner collection motor sensor disconnected, sensor defective
• Rotational transmission shaft (o6 x 30) missing
599    1-bin Exit Motor Error (Japan Only)
The transport lock sensor output does not change within 300 ms after the motor switches on  copyir.com     • Motor overload
• Motor driver defective
610    BICU - ADF communication/timeout abnormal
After 1 data frame is sent to the ADF, an ACK signal is not received within 100 ms, and is not received after 3 retries  copyir.com     • Serial line connection unstable
• External noise on the line
611    BICU - ADF communication/break reception abnormal
During communication a break (Low) signal was received from the ADF  copyir.com     • Serial line connection unstable
• Harness disconnected or defective
612    BICU - ADF communication/command abnormal
A command that cannot be executed was sent from the main machine to the ADF  copyir.com     • A software error, result of an abnormal procedure  copyir.com
620    BICU - ADF communication/timeout error
After 1 data frame is sent to the finisher MBX, an ACK signal is not received within 100 ms, and is not received after 3 retries  copyir.com     • Serial line connection unstable
• External noise on the line
621    BICU - Finisher communication/break error
During communication with the finisher MBX, the BICU received a break (Low) signal from the finisher  copyir.com     • Serial line connection unstable
• External noise on the line
623    BICU - Tray 1~4 communication/timeout error
After 1 data frame is sent to the trays, an ACK signal is not received within 100 ms, and is not received after 3 retries  copyir.com     • Serial line connection unstable
• External noise on the line
624    BICU - Tray 1~4 communication/break reception error
During communication with the finisher trays, the BICU received a break (Low) signal  copyir.com     • Serial line connection unstable
• External noise on the line
626    BICU - LCT communication/timeout error
After 1 data frame is sent to the LCT, an ACK signal is not received within 100 ms, and is not received after 3 retries  copyir.com     • Serial line connection unstable
• External noise on the line
627    BICU - LCT communication/break reception error
During communication with the LCT, the BICU received a break (Low) signal  copyir.com     • Serial line connection unstable
• External noise on the line
650    NRS Modem Communication Error
One of the following factors could be the cause of this error:
• In the User Tools, check the settings for the dial-up user name and dial up password  copyir.com  
• Modem has been disconnected  copyir.com  
• Modem board disconnected    Check the following for a machine that is using Cumin (NRS modem):
• An error was returned during the dialup connection
• A network was detected at startup
• At startup the machine detected that the NIB was disabled, or did not detect a modem board
651    Illegal Remote Service Dial-up
An expected error occurred when Cumin-M dialed up the NRS Center    • Software bug
• No action is required because only the count is logged
670    Engine startup error
The machine engine, controlled by the BICU (Base Image Control Unit), was operating incorrectly when the machine was switched on or returned to normal operation from the energy save mode  copyir.com     • Check the connections between BICU and controller
• BICU defective
• Controller board defective
• PSU defective
672    Controller startup error
• After power on, the line between the controller and the operation panel did not open for normal operation  copyir.com  
• After normal startup, communication with the controller stopped  copyir.com     • Controller stalled
• Controller installed incorrectly
• Controller board defective
• Operation panel harness disconnected or defective
700    ADF original pick-up error 1
Pick-up roller HP sensor signal does not change after the pick-up motor has turned on  copyir.com     • Pick-up roller HP sensor defective
• Pick-up motor defective
• Timing belt slipping, out of position
• ADF main board defective
701    ADF bottom plate motor error
• Bottom plate position sensor does not detect the plate after the bottom plate lift motor switches on to lift the plate  copyir.com  
• Bottom plate HP sensor does not detect the plate after the bottom plate motor reverses to lower the plate  copyir.com     • Bottom plate position sensor defective
• Bottom plate HP sensor defective
• Bottom plate motor defective
• ADF main board defective
720    Finisher transport motor error
The encoder pulse of the finisher transport motor does not change state (high/low) within 600 ms and does not change after 2 retries  copyir.com     • Finisher transport motor defective
• Transport motor harness disconnected, or defective
• Finisher main board defective
721    Finisher jogger motor error
• The finisher jogger HP sensor remains de-activated for more 1,000 pulses when returning to home position  copyir.com  
• The finisher jogger HP sensor remains activated for more than 1,000 pulses when moving away from home position    • Jogger HP sensor defective
• Jogger mechanism overload
• Jogger motor defective (not rotating)
• Finisher main board defective
• Harness disconnected or defective
723    Feed-Out Belt Motor (B478)
The pawl of the feed-out belt did not return to the home position during the prescribed time after 2 attempts to detect    • Stack feed-out belt HP sensor loose, broken, defective
• Feed-out belt motor defective
• Finisher control board defective
724    Finisher staple hammer motor error (B478)
The staple hammer motor did not return to the home position within the prescribed time (340 ms)  copyir.com     • Staple hammer HP sensor loose, broken, defective
• Electrical overload on the stapler drive PCB elect
• Staple hammer motor defective
• Finisher main board defective
725    Finisher stack feed-out motor error B140
The stack feed-out belt HP sensor does not activate within the prescribed number of pulses after the stack feed-out motor turns on and does not activate after 2 retries  copyir.com     • Stack feed-out HP sensor defective
• Harness disconnected or defective
• Stack feed-out motor defective
• Finisher main board defective
• Motor overload
725    Exit guide motor B246
The status of the exit guide sensor did not change at the prescribed time during operation of the exit guide  copyir.com     • Exit guide open sensor loose, broken, defective  copyir.com
• Exit guide motor defective
• Finisher main board defective
726    Finisher upper tray lift motor error B140
The paper height sensor does not activate within the prescribed time after the upper tray lift motor turns on, or the sensor remains on after the motor reverses to lower the tray  copyir.com     • Upper tray paper height sensor defective
• Sensor harness disconnected, defective
• Tray lift motor defective
• Finisher main board defective
• Tray lift motor overload
726    Front shift jogger motor error (B703) B246
The sides fences do not retract within the prescribed time after the shift jogger motor switches on  copyir.com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code  copyir.com     • Shift jogger motor disconnected, defective
• Shift jogger motor overloaded due to obstruction
• Shift jogger HP sensor disconnected, defective
727    Finisher stapler rotation motor error B140
The stapler motor switches on but the motor does not return to the home position within the prescribed number of pulses  copyir.com  After 2 counts, the SC is logged as a jam  copyir.com     • Stapler rotation motor defective
• Poor stapler rotation motor connection
• Stapler rotation sensor defective
• Finisher main board defective
• Rotation motor overload
727    Rear shift jogger motor (B703) B246
The side fences do not retract within the prescribed time after the shift jogger motor switches on  copyir.com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code  copyir.com     • Motor harness disconnected, loose, defective
• Motor defective
• Motor overload
• HP defective
728    Shift jogger retraction motor error (B703) B246
The side fences do not retract within the prescribed time after the retraction motor switches on  copyir.com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code  copyir.com     • Motor harness disconnected, loose, defective
• Motor defective
• Motor overload
• HP defective
729    Finisher punch motor error
The punch HP sensor does not activate within the prescribed time after the punch motor turns on  copyir.com     • Punch HP sensor defective
• Sensor harness disconnected, defective
• Punch motor defective
• Finisher main board defective
• Poor punch motor overload
730    Finisher stapler movement motor error B140
The stapler HP sensor does activate within the prescribed time after the stapler motor turns on and moves the stapler away from home position  copyir.com  After 2 counts, the SC is logged as a jam  copyir.com     • Stapler HP sensor defective
• Sensor harness disconnected, defective
• Stapler movement motor defective
• Finisher main board defective
• Stapler movement motor overload
730    Finisher Tray 1 shift motor error B246
The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position  copyir.com  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code    • Shift tray HP sensor of the upper tray disconnected, defective
• Shift tray motor of the upper tray is disconnected, defective
• Shift tray motor of the upper tray overloaded due to obstruction
732    Finisher shift roller motor error
The shift roller HP sensor does not activate within the prescribed time after the shift roller motor turns on  copyir.com  After 2 counts, the SC is logged as a jam  copyir.com     • Shift roller HP sensor defective
• Sensor harness disconnected, defective
• Shift roller motor defective
• Finisher main board defective
• Shift roller motor overload
733    Finisher lower tray lift motor error
After the lift motor switches on to lift the tray, paper height sensor 2 does not detect the top of the paper stack, or after the motor reverses to lower the stack the top of the stack remains detected (the status of paper height sensor 1 does not change)  copyir.com  After 2 counts, the SC is logged as a jam  copyir.com     • Paper height sensor 1 or 2 defective
• Sensor harness disconnected, defective
• Tray lift motor defective
• Finisher main board defective
• Tray lift motor overload
735    Finisher pre-stack motor error
• The pre-stack motor starts but does not return to the home position within 400 pulses  copyir.com  After 2 counts, the SC is logged as a jam  copyir.com  
• Motor does not return to the home position within 280 pulses immediately before or after prestacking  copyir.com  After 2 counts, the SC is logged as a jam  copyir.com     • Jogger HP sensor defective
• Sensor harnesses disconnected, defective
• Pre-stack motor defective
• Finisher main board defective
• Pre-stack motor overload
736    Finisher paper exit guide plate motor error
The paper exit guide plate motor starts but the paper exit guide plate HP sensor does not activate within 750 ms  copyir.com  After 2 counts, the SC is logged as a jam    • Guide plate HP sensor defective
• Sensor harness disconnected, defective
• Paper exit guide plate motor defective
• Finisher main board defective
• Guide plate motor overload
737    Trimmed staple waste hopper full
The hopper that holds the waste from staple trimming is full  copyir.com     • Staple waste hopper full
• St

;
Copyright MAXXmarketing Webdesigner GmbH

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب