لمینت MKP
1402-06-04
Menu
E000-0001 Fixing Assembly low temperature error
Temperature of the Fixing Main Thermistor (THM1) does not reach 70 degC although 20 seconds have passed after starting the Fixing Roller temperature control copyir.com 1 copyir.com Check the connection of the Fixing Assembly copyir.com (Connection error of the Drawer, connector disconnection, open circuit) -> Replace the Heater Assembly copyir.com 2 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10) (connector disconnection, open circuit, the caught cable) copyir.com 3 copyir.com Replace the Fixing Power Supply PCB (PCB10) copyir.com 4 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E000-0002 Fixing Assembly low temperature error
Temperature of the Fixing Main Thermistor (THM1) does not reach 10 degC although 20 seconds have passed after starting the Fixing Roller temperature control copyir.com 1 copyir.com Check the connection of the Fixing Assembly copyir.com (Connection error of the Drawer, connector disconnection, open circuit) -> Replace the Heater Assembly copyir.com 2 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10) (connector disconnection, open circuit, the caught cable) copyir.com 3 copyir.com Replace the Fixing Power Supply PCB (PCB10) copyir.com 4 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E000-0010 Fixing Assembly low temperature error
Turning OFF and then ON the power without clearing the error copyir.com Clear the error copyir.com
E001-0002 Fixing Assembly high temperature error (software detection)
• The Fixing Main Thermistor (THM1) detects 230 degC or higher copyir.com • The Fixing Sub Thermistor 1 (THM2)/Fixing Sub Thermistor 2 (THM3) detects 230 degC or higher for 2 consecutive seconds copyir.com 1 copyir.com Check if the cable of the Thermistor is caught copyir.com -> Replace the Thermistors copyir.com -> Replace the Fixing Upper Unit copyir.com 2 copyir.com IH control error copyir.com -> Replace the Fixing Power Supply PCB (PCB10), the DC Controller PCB (PCB1), or the Main Driver PCB (PCB2) copyir.com
E001-0003 Fixing Assembly high temperature error (hardware detection)
• The Fixing Main Thermistor (THM1) detects hardware overheating copyir.com • The Fixing Sub Thermistor 1 (THM2)/Fixing Sub Thermistor 2 (THM3) detects hardware overheating copyir.com 1 copyir.com Check if the cable of the Thermistor is caught copyir.com -> Replace the Thermistors copyir.com -> Replace the Fixing Upper Unit copyir.com 2 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E001-0004 Fixing Assembly high temperature error (hardware detection)
Abnormal temperature difference among the Thermistors was detected copyir.com 1 copyir.com Check if the cable of the Thermistor is caught or is open circuit copyir.com -> Replace the Thermistors copyir.com -> Replace the Fixing Upper Unit copyir.com 2 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com 4 copyir.com Check if the Fixing Shutter operates copyir.com -> Replace the Fixing Assembly copyir.com
E001-0010 Fixing Assembly high temperature error
Turning OFF and then ON the power without clearing the error copyir.com Clear the error copyir.com
E002-0001 Fixing Assembly temperature rise error
• Temperature of the Fixing Main Thermistor (THM1) does not reach 100 degC although 12 seconds have passed since it reached above 70 degC after starting the Fixing Roller temperature control copyir.com • Temperature of the Fixing Main Thermistor does not reach 130 degC although 12 seconds have passed since it reached above 100 degC after starting the Fixing Roller temperature control copyir.com • Temperature of the Fixing Main Thermistor does not reach 150 degC although 20 seconds have passed since it reached above 130 degC after starting the Fixing Roller temperature conrtol copyir.com 1 copyir.com Check the connection of the Fixing Main Thermistor (THM1) copyir.com -> Replace the Fixing Main Thermistor Unit copyir.com 2 copyir.com Check the installation of the Fixing Main Thermistor copyir.com -> Replace the Fixing Upper Unit copyir.com 3 copyir.com Replace the Fixing Power Supply PCB (PCB10) copyir.com 4 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com 6 copyir.com Replace the Relay PCB (PCB5) copyir.com
E002-0010 Fixing Assembly temperature rise error
Turning OFF and then ON the power without clearing the error copyir.com Clear the error copyir.com
E003-0000 Fixing Assembly temperature decrease error
The Fixing Main Thermistor (THM1) detects 70 degC or lower for 2 seconds or longer although the temperature reached above 100 degC after starting the Fixing Roller temperature control copyir.com 1 copyir.com Check the connection of the Fixing Main Thermistor (THM1) copyir.com -> Replace the Fixing Main Thermistor Unit copyir.com 2 copyir.com Check the installation of the Fixing Main Thermistor copyir.com -> Replace the Fixing Upper Unit copyir.com 3 copyir.com Replace the Fixing Power Supply PCB (PCB10) copyir.com 4 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com 6 copyir.com Replace the Relay PCB (PCB5) copyir.com
E003-0010 Fixing Assembly temperature decrease error
Turning OFF and then ON the power without clearing the error copyir.com Clear the error copyir.com
E004-0010 Fixing Power Supply error
Turning OFF and then ON the power without clearing the error copyir.com Clear the error copyir.com
E004-0205 Fixing Power Supply error
Detect that the Fixing Main Thermistor Unit is not connected copyir.com 1 copyir.com Check the harness of the Fixing Main Thermistor (THM1) in the Fixing Assembly copyir.com 2 copyir.com Check the connection of the harness of the Fixing Assembly on the host machine side copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E005-0000 Fixing Cleaning Web absent error
After noticing the Fixing Cleaning Web absent, the web was pulled out 2000 times copyir.com 1 copyir.com Replace the Fixing Cleaning Web copyir.com 2 copyir.com Replace the Fixing Cleaning Web Level Sensor (PS45) copyir.com 3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com After executing the measures, clear the Fixing Cleaning Web counter (COPIER > COUNTER > MISC > FIXWEB) copyir.com
E005-0001 Error in Fixing Cleaning Web Drive Solenoid connection
Connection of the Fixing Cleaning Web Drive Solenoid (SL9) is not detected when the power is turned ON copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Replace the Fixing Cleaning Web Drive Solenoid (SL9) copyir.com
E005-0010 Fixing Cleaning Web errort error
Turning OFF and then ON the power without clearing the error copyir.com Clear the error copyir.com
E012-0001 Drum Motor (M1) error
Lock error of the Drum Motor (M1) copyir.com 1 copyir.com Check the connection of the Main Driver PCB (PCB2) and the Drum Motor (M1) copyir.com Motor side: J2138, PCB side: J109 2 copyir.com Check the voltage of the Drum Motor (M1) J2151 copyir.com If voltage is 0V, check the connection of the Relay PCB J520 copyir.com 3 copyir.com Replace the Drum Motor (M1) copyir.com 4 copyir.com Check the gear of the Drum Drive Shaft copyir.com If the load is too much, replace the Process Unit and the Drum Drive Unit (Shaft) copyir.com 5 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E013-0001 Error in Waste Toner Lock Detection Connector disconnection
The Waste Toner Lock Detection Switch (SW5) detects locked state 3 times for 200 msec at power-on copyir.com Check the connection of the Waste Toner Lock Detection Switch (SW5) and the Main Driver PCB (PCB2) copyir.com Switch side: J3050, PCB side: J103
E013-0002 Error in Waste Toner Feed Screw Lock detection
The Waste Toner Lock Detection Switch detects locked state 3 times for 200 msec while the Developing Assembly is driven copyir.com 1 copyir.com Check the Waste Toner Container and the Waste Toner Container Pipe copyir.com If toner overflowed from the Waste Toner Container clogs the outlet of the Waste Toner Pipe, remove the clogged toner copyir.com After removing it, check that the screw can be seen from the outlet of the pipe copyir.com 2 copyir.com Check the connection of the Waste Toner Lock Detection Switch (SW5) and the Main Driver PCB (PCB2) copyir.com 3 copyir.com Check the connection of the Main Driver PCB (PCB2) and the DC Controller PCB (PCB1) copyir.com Main Controller side: J3050, DC Controller side: J103 4 copyir.com Replace the Waste Toner Lock Detection Switch (SW5) copyir.com 5 copyir.com Replace the Waste Toner Feed Unit copyir.com 6 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 7 copyir.com Replace the DC Controller PCB (PCB1) copyir.com (When the error is still displayed after replacing the Waste Toner Feed Unit and the Main Driver PCB (PCB2) copyir.com)
E014-0001 Fixing Motor error
Lock error of the Fixing Motor (M3) copyir.com 1 copyir.com Check the gear of the Fixing Drive Unit copyir.com -> Replace the gear copyir.com 2 copyir.com Replace the Fixing Motor (M3) copyir.com 3 copyir.com Check the connection drawer between the Fixing Assembly and the host machine copyir.com 4 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E017-0001 ETB disengagement error
Disengagement of the ETB is not completed within the specified period of time copyir.com 1 copyir.com Check the connection of the ETB Disengage Sensor (PS56) copyir.com Sensor side: J2101, J3270, PCB side: J343 (Duplex Driver PCB (PCB4)) 2 copyir.com Check the connection of the Duplex Feed Left Motor (M19) copyir.com Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4)) 3 copyir.com Replace the ETB Disengage Sensor (PS56) copyir.com 4 copyir.com Replace the Duplex Feed Left Motor (M19) copyir.com 5 copyir.com Replace the Duplex Driver PCB (PCB4) copyir.com 6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com NOTE: Check if the Disengagement Cam is stained copyir.com If necessary, clean it copyir.com Check if the drive system (gear, Motor, one-way) is failed copyir.com If necessary, replace it copyir.com Check if the link with the Fixing Feed Handle is failed copyir.com If necessary, replace it copyir.com
E017-0002 ETB engagement error
Engagement of the ETB is not completed within the specified period of time copyir.com 1 copyir.com Check the connection of the ETB Disengage Sensor (PS55) copyir.com Sensor side: J2100, J3270, PCB side: J343 (Duplex Driver PCB (PCB4)) 2 copyir.com Check the connection of the Duplex Feed Left Motor (M19) copyir.com Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4)) 3 copyir.com Replace the ETB Engage Sensor (PS55) copyir.com 4 copyir.com Replace the Duplex Feed Left Motor (M19) copyir.com 5 copyir.com Replace the Duplex Driver PCB (PCB4) copyir.com 6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com NOTE: Check if the Disengagement Cam is stained copyir.com If necessary, clean it copyir.com Check if the drive system (gear, Motor, one-way) is failed copyir.com If necessary, replace it copyir.com Check if the link with the Fixing Feed Handle is failed copyir.com If necessary, replace it copyir.com
E017-0003 ETB HP error
Engagement of the ETB was not completed at initialization copyir.com If this error occurs at installation, the ETB Disengage Member (Transfer Frame Stopper) may be left unremoved copyir.com Refer to the troubleshooting “Remedy to be implemented when the ETB Disengage Member (Transfer Frame Stopper) is left unremoved” in the Service Manual, and check whether the ETB Disengage Member is left unremoved or not and implement appropriate procedure copyir.com If this error occurs at times other than installation, follow the following steps to implement check and remedy copyir.com 1 copyir.com Check the connection of the ETB Disengage Sensor (PS56) copyir.com Sensor side: J2101, J3270, PCB side: J343 (Duplex Driver PCB (PCB4)) 2 copyir.com Check the connection of the Duplex Feed Left Motor (M19) copyir.com Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4)) 3 copyir.com Replace the ETB Disengage Sensor (PS56) copyir.com 4 copyir.com Replace the Duplex Feed Left Motor (M19) copyir.com 5 copyir.com Replace the Duplex Driver PCB (PCB4) copyir.com 6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com NOTE: Check if the Disengagement Cam is stained copyir.com If necessary, clean it copyir.com Check if the drive system (gear, Motor, one-way) is failed copyir.com If necessary, replace it copyir.com Check if the link with the Fixing Feed Handle is failed copyir.com If necessary, replace it copyir.com
E020-0000 Developing Assembly toner absent error
Toner in the Developing Assembly was empty for 2 minutes copyir.com 1 copyir.com Check the connection of the Developing Toner Sensor (TS1) copyir.com Sensor side: J2133, J3089 (relay), PCB side: J3088 (relay), J114 (Main Driver PCB (PCB2)) 2 copyir.com Check the connection of the Magnet Roller Clutch (CL5) copyir.com Sensor side: J2036, J3124 (relay), J3090 (relay) PCB side: J3091(relay), J115 (Main Driver PCB (PCB2)) 3 copyir.com Check the connection of the Toner Feed Motor (M28) copyir.com Motor side: J2035, J3124 (relay), J3090 (relay) PCB side: J3091(relay), J115 (Main Driver PCB (PCB2)) 4 copyir.com Check the connection of the Buffer Toner Sensor (TS3) copyir.com Sensor side: J2039, J3124 (relay), J3090 (relay) PCB side: J3091(relay), J115 (Main Driver PCB (PCB2)) 5 copyir.com Replace the Developing Toner Sensor (TS1) copyir.com 6 copyir.com Replace the Magnet Roller Clutch (CL5) copyir.com 7 copyir.com Replace the Toner Feed Motor (M28) copyir.com 8 copyir.com Replace the Buffer Toner Sensor (TS3) copyir.com 9 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 10 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E020-0001 Error in Developing Toner Sensor connection detection
The connection detection port was OFF at power-on copyir.com 1 copyir.com Check the connection of the Developing Toner Sensor (TS1) copyir.com Sensor side: J2133, J3089 (relay), PCB side: J3088 (relay), J114 (Main Driver PCB (PCB2)) 2 copyir.com Replace the Developing Toner Sensor (TS1) copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E020-0002 Error in Buffer Toner Sensor connection detection
The connection detection port was OFF at power-on copyir.com 1 copyir.com Check the connection of the Buffer Toner Sensor (TS3) copyir.com Sensor side: J2039, J3124 (relay), J3090 (relay) PCB side: J3091(relay), J115 (Main Driver PCB (PCB2)) 2 copyir.com Replace the Buffer Toner Sensor (TS3) copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E020-0003 Error in the Toner Excess Supply Sensor connection detection
The connection detection port was OFF at power-on copyir.com 1 copyir.com Check the connection of the Toner Excess Supply Sensor (TS2) copyir.com Sensor side: J2038, J3124 (relay), J3090 (relay) PCB side: J3091(relay), J115 (Main Driver PCB (PCB2)) 2 copyir.com Replace the Toner Excess Supply Sensor (TS2) copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E020-0004 Error in Magnet Roller Clutch connection detection
The connection detection port was OFF at power-on copyir.com 1 copyir.com Check the connection of the Magnet Roller Clutch (CL5) copyir.com Sensor side: J2036, J3124 (relay), J3090 (relay) PCB side: J3091(relay), J115 (Main Driver PCB (PCB2)) 2 copyir.com Replace the Magnet Roller Clutch (CL5) copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E020-0021 Error in Developing Assembly Toner Sensor Cleaning Scraper displacement
State with toner was detected continuously copyir.com 1 copyir.com Turn OFF the main power copyir.com 2 copyir.com Replace the Developing Assembly copyir.com 3 copyir.com Turn ON the main power copyir.com
E023-0001 Developing Motor error
Lock error of the Developing Motor (M2) copyir.com 1 copyir.com Check the connection of the Connector copyir.com Motor side: J2319, Main Driver PCB (PCB2) side: J109 2 copyir.com Check the voltage of the Developing Motor (M2) J2152 copyir.com If voltage is 0V, check the connection of the Relay PCB J520 copyir.com 3 copyir.com Check the load of the Developing Motor (M2) copyir.com Manually turn the Developing Motor (M2) located at the rear of the host machine to check it copyir.com 4 copyir.com Replace the Developing Motor (M2) copyir.com 5 copyir.com Replace the Developing Clutch (CL1) copyir.com (When an error occurs while the Developing Clutch is ON copyir.com) 6 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 7 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E023-0002 Error in Magnet Roller Clutch connection detection
Connection of the Magnet Roller Clutch (CL5) cannot be detected 5 times with 20 msec time interval copyir.com 1 copyir.com Check the connection of the Magnet Roller Clutch (CL5) copyir.com Sensor side: J2006, Main Driver PCB (PCB2) side: J109 2 copyir.com Replace the Magnet Roller Clutch (CL5) copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E025-0001 Toner Feed Motor error
Overcurrent of the Toner Feed Motor (M28) was detected copyir.com 1 copyir.com Check the connection of the Connector copyir.com Motor side: J2036, Buffer Unit relay: J3124, Front side relay: J3090, Rear side relay: J3091, Main Driver PCB (PCB2) side: J115 2 copyir.com Replace the Toner Feed Motor (M28) copyir.com 3 copyir.com Check if toner is clogged inside of the Buffer copyir.com Turn the Drive Shaft of the Motor with your hand to check it copyir.com If the load is too much, inside of the Buffer may be clogged, so clean inside of it copyir.com 4 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E027-0001 Toner Supply Motor error
Lock error of the Toner Supply Motor (M10) copyir.com 1 copyir.com Check the connection of the Connector copyir.com Motor side: J2037, Front side relay: J3080, Rear side relay: J3063, Main Driver PCB (PCB2) side: J117 2 copyir.com Remove the Toner Container, and check if an error occurs copyir.com If an error does not occur, reinstall the Toner Container and check again copyir.com If an error occurs, check the driving area of connection point of the container copyir.com If an error occurs, go on to 3 copyir.com 3 copyir.com Replace the Toner Supply Motor (M10) copyir.com 4 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E032-0001 Failure of NE Controller Counter
Detection of open circuit of count pulse signal copyir.com Disconnection of cable copyir.com
E041-0001 Right Deck Lifter Motor error
Overcurrent of the Right Deck Lifter Motor was detected copyir.com 1 copyir.com Check for displacement of the Lifter Wire of the Right Deck copyir.com 2 copyir.com Check for hindrance to smooth movement of the Deck Base Plate of the Right Deck copyir.com
E041-0002 Left Deck Lifter Motor error
Overcurrent of the Leftt Deck Lifter Motor was detected copyir.com 1 copyir.com Check for displacement of the Lifter Wire of the Left Deck copyir.com 2 copyir.com Check for hindrance to smooth movement of the Deck Base Plate of the Left Deck copyir.com
E041-0003 Cassette 3 Lifter Motor error
Overcurrent of the Cassette 3 Lifter Motor was detected copyir.com 1 copyir.com Check for error around the Lifter of the Cassette 3 copyir.com 2 copyir.com Check for hindrance to smooth movement of the Cassette Base Plate of the Cassette 3 copyir.com
E041-0004 Cassette 4 Lifter Motor error
Overcurrent of the Cassette 4 Lifter Motor was detected copyir.com 1 copyir.com Check for error around the Lifter of the Cassette 4 copyir.com 2 copyir.com Check for hindrance to smooth movement of the Cassette Base Plate of the Cassette 4 copyir.com
E053-0001 Error in Reverse Upper Flapper Solenoid connection detection
Connection of the Reverse Upper Flapper Solenoid (SL5) cannot be detected 5 times with 20 msec time interval copyir.com 1 copyir.com Check the connection of the Reverse Upper Flapper Solenoid (SL5) copyir.com Solenoid side: J2115, Duplex Driver PCB side: J340 2 copyir.com Replace the Reverse Upper Flapper Solenoid (SL5) copyir.com 3 copyir.com Replace the Duplex Driver PCB (PCB4) copyir.com 4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E060-0001 Primary Charging Shutter HP open error
The Primary Charging Shutter Sensor (PS94) detects that the shutter is opened although it is moved to the close position copyir.com 1 copyir.com Check the position of the Primary Charging Shutter and the Cleaning Pad copyir.com 1-A copyir.com In the case that the Primary Charging Shutter and the Cleaning Pad fail to operate (stopped at HP at front side) 1-A-1 copyir.com Check the connection of the Primary Charging Wire Cleaning Motor (M6) copyir.com Motor side: J3017, J3060 (iR-ADV 8xxx)/J3160 (iRADV 6xxx) (relay), PCB side: J3177 (relay), J107 (Main Driver PCB (PCB2)) 1-A-2 copyir.com Replace the Primary Charging Wire Cleaning Motor (M6) copyir.com 1-B copyir.com In the case that the Primary Charging Shutter and the Cleaning Pad are stopped at rear side (close operation position) 1-B-1 copyir.com Check the connection of the Primary Charging Shutter Sensor (PS94) copyir.com Sensor side: J2029, J3089 (relay), PCB side: J3088 (relay), J114 (Main Driver PCB (PCB2)) 1-B-2 copyir.com Replace the Primary Charging Shutter Sensor (PS94) copyir.com 1-C copyir.com In the case that the Primary Charging Shutter and the Cleaning Pad are stopped along the way 1-C-1 copyir.com Check the loosening of screw on the Slider Pin and abrasion of the pin copyir.com Tighten the screw or replace the Slider Pin copyir.com 1-C-2 copyir.com Replace the Primary Charging Assembly copyir.com 1-D copyir.com In the case that the Primary Charging Shutter stops at front side and the Cleaning Pad moves to rear side 1-D-1 copyir.com Check if the Shutter Mounting Plate is deformed copyir.com If so, replace the Shutter Unit copyir.com 1-D-2 copyir.com Check the loosening of screw on the Slider Pin and abrasion of the pin copyir.com Tighten the screw or replace the Slider Pin copyir.com 1-D-3 copyir.com Replace the Primary Charging Assembly copyir.com 2 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E060-0002 Primary Charging Shutter HP close error
The Primary Charging Shutter Sensor (PS94) detects that the shutter is closed although it is moved to the open position copyir.com 1 copyir.com Check the position of the Primary Charging Shutter and the Cleaning Pad copyir.com 1-A copyir.com In the case that the Primary Charging Shutter and the Cleaning Pad fail to operate (stopped at HP at front side) 1-A-1 copyir.com Check the connection of the Primary Charging Wire Cleaning Motor (M6) copyir.com Motor side: J3017, J3060 (iR-ADV 8xxx)/J3160 (iRADV 6xxx) (relay), PCB side: J3177 (relay), J107 (Main Driver PCB (PCB2)) 1-A-2 copyir.com Replace the Primary Charging Wire Cleaning Motor (M6) copyir.com 1-B copyir.com In the case that the Primary Charging Shutter and the Cleaning Pad are stopped at rear side (close operation position) 1-B-1 copyir.com Check the connection of the Primary Charging Shutter Sensor (PS94) copyir.com Sensor side: J2029, J3089 (relay), PCB side: J3088 (relay), J114 (Main Driver PCB (PCB2)) 1-B-2 copyir.com Replace the Primary Charging Shutter Sensor (PS94) copyir.com 1-C copyir.com In the case that the Primary Charging Shutter and the Cleaning Pad are stopped along the way 1-C-1 copyir.com Check the loosening of screw on the Slider Pin and abrasion of the pin copyir.com Tighten the screw or replace the Slider Pin copyir.com 1-C-2 copyir.com Replace the Primary Charging Assembly copyir.com 2 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E061-0001 Potential control error (VL)
The measured value in the dark area (VL) differs +/-30V or higher than the target potential at potential control copyir.com NOTE: If the difference is somewhere between +/-10V and less than 30V, alarm is indicated copyir.com 1 copyir.com Check the connection of the Pre-exposure LED (connector connection, open circuit, the caught cable) copyir.com 2 copyir.com Check the installation of the Primary Charging Assembly (connector connection, open circuit, the caught cable) copyir.com 3 copyir.com Check the fixation state of the Drum and the Drum Shaft copyir.com (Check if the drum fixation cylinder is properly installed copyir.com) 4 copyir.com Check if the Dustproof Glass is soiled copyir.com If necessary, clean it copyir.com 5 copyir.com Check the installation of the Laser Scanner Unit (connector connection, open circuit, the caught cable) copyir.com 6 copyir.com Check the installation of the Primary Charging High Voltage PCB (PCB11), and its connection (connector connection, open circuit, the caught cable) copyir.com 7 copyir.com Check the installation of the Potential Sensor (connector connection, open circuit, the caught cable) copyir.com 8 copyir.com Check the installation of the Drum Motor (M1), and its connection (connector connection, open circuit, the caught cable) copyir.com 9 copyir.com Replace the parts copyir.com • Primary Charging Assembly • Laser Scanner Unit • Potential Sensor • Primary Charging High Voltage PCB (PCB11) • Drum Motor (M1) • Main Driver PCB (PCB2) • DC Controller PCB (PCB1)
E061-0101 Potential control error (VD)
Potential in the dark area did not fall within the range (target value +/-10V) although retry was executed 8 times at VD potential control copyir.com 1 copyir.com Check the connection of the Pre-exposure LED (connector connection, open circuit, the caught cable) copyir.com 2 copyir.com If the current value of the Primary Charging Roller (COPIER > DISPLAY > DPOT > PRIM-C) is 1550 micro A or higher, execute 2-1 to 3 copyir.com 2-1 copyir.com Increase the grid voltage of the Primary Charging Assembly by 100V (COPIER > ADJUST > HV-PRI > PRI-GRID) copyir.com 2-2 copyir.com Execute the potential control (COPIER > FUNCTION > DPC > DPC) copyir.com 2-3 copyir.com Turn OFF and then ON the power copyir.com 3 copyir.com Check the installation of the Primary Charging Assembly (connector connection, open circuit, the caught cable) copyir.com 4 copyir.com Check the installation of the Primary Charging High Voltage PCB (PCB11), and its connection (connector connection, open circuit, the caught cable) copyir.com 5 copyir.com Check the installation of the Drum Motor (M1), and its connection (connector connection, open circuit, the caught cable) copyir.com 6 copyir.com Replace the parts copyir.com • Primary Charging Assembly • Primary Charging High Voltage PCB • Drum Motor (M1) • Main Driver PCB (PCB2) • DC Controller PCB (PCB1)
E064-00FF High voltage setting error
With the state in which the developing AC is output, 600V or higher developing DC output was detected copyir.com (Basically, this error is not detected copyir.com However, to detect that the image formation-related backup data is corrupted or to protect the hardware in case of 600V or higher developing DC output, this is to be an error copyir.com) 1 copyir.com Turn OFF and then ON the main power copyir.com 2 copyir.com Replace the DCON PCB copyir.com
E065-0001 Primary charging/grid high voltage output leak error
The leak detection signal was detected 5 times in a row for every 20 msec copyir.com 1 copyir.com Check the connection between the Main Driver PCB (PCB2) and the High Voltage Unit copyir.com Main Driver side: J111, High Voltage Unit side: J3097 2 copyir.com Check the connection between the Relay PCB (PCB5) and the High Voltage Unit copyir.com Relay side: J519, High Voltage Unit side: J3099 3 copyir.com Replace the Primary Charging Assembly copyir.com 4 copyir.com Check the connection inside of the High Voltage Unit copyir.com High Voltage Unit Relay (J3097) and Primary Charging High Voltage PCB (PCB11) (J3501) High Voltage Unit relay (J3099) and Pre-transfer Charging PCB (PCB26) (J3545, J3500) 5 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 6 copyir.com Replace the Primary Grid High Voltage Connector (FM4- 1006) copyir.com
E066-0001 Pre-transfer Charging Shutter HP open error
The Pre-transfer Charging Shutter Sensor (PS95) detects that the shutter is opened although it is moved to the close position copyir.com 1 copyir.com Check the position of the Pre-transfer Charging Shutter copyir.com 1-A copyir.com In the case that the Pre-transfer Charging Shutter fails to operate (stopped at HP at front side) Check the connection of the Pre-transfer Charging Wire Cleaning Motor (M7) copyir.com Sensor side: J3108, J3089 (relay), PCB side: J3088 (relay), J114 (Main Driver PCB (PCB2)) 1-B copyir.com In the case that the Pre-transfer Charging Shutter is stopped at rear side (close operation position) 1-B-1 copyir.com Check that the Primary Fan Duct is closed copyir.com Close the Primary Fan Duct copyir.com 1-B-2 copyir.com Check movement of the pin to push the Pre-transfer Charging Shutter Sensor (PS95) copyir.com Replace the Pin copyir.com 1-B-3 copyir.com Check movement of the flag on the Pre-transfer Charging Shutter Sensor (PS95) copyir.com Replace the flag/ spring copyir.com 1-B-4 copyir.com Check the connection of the Pre-transfer Charging Shutter Sensor (PS95) copyir.com Sensor side: J2114, J3215 (relay), J3067 (relay) PCB side: J3066 (relay), J130 (Main Driver PCB (PCB2)) 1-C copyir.com In the case that the Pre-transfer Charging Shutter is stopped along the way 1-C-1 copyir.com Check abrasion of the Slider Pin copyir.com Replace the Slider Pin copyir.com 1-C-2 copyir.com Replace the Pre-transfer Charging Assembly copyir.com 2 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E066-0002 Pre-transfer Charging Shutter HP close error copyir.com
The Pre-transfer Charging Shutter Sensor (PS95) detects that the shutter is closed although it is moved to the open position copyir.com 1 copyir.com Check the position of the Pre-transfer Charging Shutter copyir.com 1-A copyir.com In the case that the Pre-transfer Charging Shutter fails to operate (stopped at HP at front side) Check the connection of the Pre-transfer Charging Wire Cleaning Motor (M7) copyir.com Sensor side: J3108, J3089 (relay), PCB side: J3088 (relay), J114 (Main Driver PCB (PCB2)) 1-B copyir.com In the case that the Pre-transfer Charging Shutter is stopped at rear side (close operation position) 1-B-1 copyir.com Check that the Primary Fan Duct is closed copyir.com Close the Primary Fan Duct copyir.com 1-B-2 copyir.com Check movement of the pin to push the Pre-transfer Charging Shutter Sensor (PS95) copyir.com Replace the Pin copyir.com 1-B-3 copyir.com Check movement of the flag on the Pre-transfer Charging Shutter Sensor (PS95) copyir.com Replace the flag/ spring copyir.com 1-B-4 copyir.com Check the connection of the Pre-transfer Charging Shutter Sensor (PS95) copyir.com Sensor side: J2114, J3215 (relay), J3067 (relay) PCB side: J3066 (relay), J130 (Main Driver PCB (PCB2)) 1-C copyir.com In the case that the Pre-transfer Charging Shutter is stopped along the way 1-C-1 copyir.com Check abrasion of the Slider Pin copyir.com Replace the Slider Pin copyir.com 1-C-2 copyir.com Replace the Pre-transfer Charging Assembly copyir.com 2 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E067-0001 Developing high voltage output leak error
The leak detection signal was detected 5 times in a row for every 20 msec copyir.com 1 copyir.com Check the connection between the Main Driver PCB (PCB2) and the High Voltage Unit copyir.com Main Driver side: J112, High Voltage Unit side: J3098 2 copyir.com Check the connection between the Relay PCB (PCB5) and the High Voltage Unit copyir.com Relay side: J519, High Voltage Unit side: J3099 3 copyir.com Replace the Developing Assembly copyir.com 4 copyir.com Check the connection point of the Developing Assembly copyir.com If it is soiled, clean it copyir.com 5 copyir.com Check the connection inside of the High Voltage Unit copyir.com Check the connection of the High Voltage Unit Relay (J3097) and the Developing High Voltage PCB (J3511) copyir.com High Voltage Unit Relay (J3099) and Pre-transfer Charging PCB (J3545, J3500, J3510) 6 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E068-0001 Pre-transfer charging high voltage output leak error
The leak detection signal was detected 5 times in a row for every 20 msec copyir.com 1 copyir.com Check the connection between the Main Driver PCB (PCB2) and the High Voltage Unit copyir.com Main Driver side: J112, High Voltage Unit side: J3098 2 copyir.com Check the connection between the Relay PCB (PCB5) and the High Voltage Unit copyir.com Relay side: J519, High Voltage Unit side: J3099 3 copyir.com Replace the Pre-transfer Charging Assembly copyir.com 4 copyir.com Check the connection inside of the High Voltage Unit copyir.com Check the connection of the High Voltage Unit Relay (J3098) and the Transfer High Voltage PCB (J3544) copyir.com Check the connection of the High Voltage Unit Relay (J3099) and the Pre-transfer Charging PCB (J3545, J3500) 5 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 6 copyir.com Replace the Pre-transfer High Voltage Connector (FM4- 1007) copyir.com 7 copyir.com Replace the Pre-transfer Transformer (Post Charging Trance) of the High Voltage Unit copyir.com
E069-0001 Transfer high voltage output leak error
The leak detection signal was detected 5 times in a row for every 20 msec 1 copyir.com Check the connection between the Duplex Driver PCB (PCB4) and the High Voltage Unit copyir.com Check the connection at Duplex Driver side (J343) and the Transfer High Voltage side (J3066) copyir.com Check the connection at Duplex Driver side (J311) and the Transfer High Voltage side (J3061) copyir.com (In addition, check that 24V is output copyir.com) 2 copyir.com Check the connection of the Transfer High Voltage PCB (J3306) copyir.com 3 copyir.com Replace the ETB Unit copyir.com 4 copyir.com Replace the Duplex Driver PCB (PCB4) copyir.com
E100-11xx BD unlock error
Locked state was not detected within the specified period of time at start-up copyir.com 1 copyir.com Check if the door is opened copyir.com Close the door copyir.com 2 copyir.com Check the connection between the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35) copyir.com DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor and BD PCB: J3011 3 copyir.com Replace the Laser Scanner Unit copyir.com 4 copyir.com Replace the Laser Driver PCB (PCB35) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com NOTE: When condensation occurs inside of the machine or the Laser Scanner Unit, this error also occurs copyir.com When condensation occurs, leave the machine or the unit as it is until condensation disappears copyir.com (Use the machine or the unit in an environment where condensation does not occur copyir.com)
E100-12xx BD unlock error
After the BD range was specified, lock was unlocked for 1 second or longer copyir.com 1 copyir.com Check if the door is opened copyir.com Close the door copyir.com 2 copyir.com Check the connection between the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35) copyir.com DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor and BD PCB: J3011 3 copyir.com Replace the Laser Scanner Unit copyir.com 4 copyir.com Replace the Laser Driver PCB (PCB35) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com NOTE: When condensation occurs inside of the machine or the Laser Scanner Unit, this error also occurs copyir.com When condensation occurs, leave the machine or the unit as it is until condensation disappears copyir.com (Use the machine or the unit in an environment where condensation does not occur copyir.com)
E100-13xx Polygon Motor BD unlock error (Laser diode is not lit up/ failure of the BD PCB/power supply error, or condensation)
During the Polygon speed change, lock was unlocked for 1 second or longer copyir.com (Laser diode is not lit up/failure of the BD PCB/power supply error, or condensation) 1 copyir.com Check if the door is opened copyir.com Close the door copyir.com 2 copyir.com Check the connection between the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35) copyir.com DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor and BD PCB: J3011 3 copyir.com Replace the Laser Scanner Unit copyir.com 4 copyir.com Replace the Laser Driver PCB (PCB35) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com NOTE: When condensation occurs inside of the machine or the Laser Scanner Unit, this error also occurs copyir.com When condensation occurs, leave the machine or the unit as it is until condensation disappears copyir.com (Use the machine or the unit in an environment where condensation does not occur copyir.com)
E100-FFFF Polygon Motor BD unlock error
Failed to get the Detailed Code (communication error, power supply error, PCB failure, etc copyir.com) copyir.com 1 copyir.com Check if the door is opened copyir.com Close the door copyir.com 2 copyir.com Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35) copyir.com DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3 copyir.com Replace the Laser Scanner Unit copyir.com 4 copyir.com Replace the Laser Driver PCB (PCB35) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E102-0001 EEPROM writing error copyir.com
Failed to write to EEPROM (Power is not supplied/EEPROM failure) copyir.com 1 copyir.com Check if the door is opened copyir.com Close the door copyir.com 2 copyir.com Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35) copyir.com DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3 copyir.com Replace the Laser Scanner Unit copyir.com 4 copyir.com Replace the Laser Driver PCB (PCB35) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E103-0001 Different Laser Scanner Unit model error
The scanner for 6075/6065/6055 models was installed to the imageRUNNER ADVANCE 8105/8095/8085 models, and vice versa copyir.com Replace the Laser Scanner Unit with the one for the correct model copyir.com
E110-11xx Polygon Motor FG unlock error
Locked state was not detected within the specified period of time at start-up copyir.com (Power is not supplied/Polygon Motor signal error) 1 copyir.com Check if the door is opened copyir.com Close the door copyir.com 2 copyir.com Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35) copyir.com DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3 copyir.com Replace the Laser Scanner Unit copyir.com 4 copyir.com Replace the Laser Driver PCB (PCB35) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E110-12xx Polygon Motor FG unlock error
After the BD range was specified, lock was unlocked for 1 second or longer copyir.com (Power is not supplied/Polygon Motor signal error) 1 copyir.com Check if the door is opened copyir.com Close the door copyir.com 2 copyir.com Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35) copyir.com DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3 copyir.com Replace the Laser Scanner Unit copyir.com 4 copyir.com Replace the Laser Driver PCB (PCB35) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E110-13xx Polygon Motor FG unlock error
During the Polygon speed change, lock was unlocked for 1 second or longer copyir.com (Power is not supplied/Polygon Motor signal error) 1 copyir.com Check if the door is opened copyir.com Close the door copyir.com 2 copyir.com Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35) copyir.com DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3 copyir.com Replace the Laser Scanner Unit copyir.com 4 copyir.com Replace the Laser Driver PCB (PCB35) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E110-FFFF Polygon Motor FG unlock error
Failed to get the Detailed Code (communication error, power supply error, PCB failure) copyir.com 1 copyir.com Check if the door is opened copyir.com Close the door copyir.com 2 copyir.com Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35) copyir.com DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3 copyir.com Replace the Laser Scanner Unit copyir.com 4 copyir.com Replace the Laser Driver PCB (PCB35) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E121-0001 Laser Scanner Cooling Fan error copyir.com
The Fan stop signal is detected for 5 seconds or longer and retry is failed 4 times in a row although the Laser Scanner Cooling Fan (FM16) is turned ON copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Replace the Laser Scanner Cooling Fan (FM16) copyir.com
E197-0001 Error in Main Driver PCB connection detection
Failed to establish a communication between the DC Controller PCB (PCB1) and the Main Driver PCB (PCB2) copyir.com 1 copyir.com Check the connection of the DC Controller PCB (PCB1) and the Main Driver PCB (PCB2) copyir.com DC Controller side: J411, J412, Main Driver side: J125, J126 2 copyir.com Check the Main Driver PCB (PCB2) power supply connection copyir.com Check the connection at the Main Driver side (J128) and the DC Controller side (J414), and check the voltage copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E197-0002 Error in Feed Driver PCB connection detection
Failed to establish a communication between the DC Controller PCB (PCB1) and the Feed Driver Pub (PCB3) copyir.com 1 copyir.com Check the connection of the DC Controller PCB (PCB1) and the Feed Driver PCB (PCB3) copyir.com DC Controller side: J421, Feed Driver side: J204 2 copyir.com Check the connection of the Feed Driver PCB (PCB3) and the DC-DC Converter PCB copyir.com Check the connection at the Feed Driver side (J218) and the DC-DC Converter side (J9033) copyir.com 3 copyir.com Check the power supply of the Feed Driver PCB (PCB3) copyir.com Check if appropriate voltages are applied to the Feed Driver side (12V to 1pin, 5V to 3pin, 3 copyir.com3V to 4pin) copyir.com -> If not, replace the DC-DC Converter PCB copyir.com 4 copyir.com Replace the Feed Driver PCB (PCB3) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E197-0003 Error in Duplex Driver PCB connection detection
Failed to establish a communication between the DC Controller PCB (PCB1) and the Duplex Driver PCB (PCB4) copyir.com 1 copyir.com Check the connection between the DC Controller PCB (PCB1) and the Fixing Feed Drawer copyir.com DC Controller side: J431, J432, Fixing Feed Drawer (host machine side): J3002D Fixing Feed Drawer (Fixing Feed side): J3002L, Duplex Driver side: J300, J301 2 copyir.com Check the connection of the Duplex Driver PCB (PCB4) and the DC-DC Converter PCB copyir.com Check the connection at the Duplex Driver side (J311) and the DC-DC Converter side (J9034) copyir.com 3 copyir.com Check the power supply of the Duplex Driver PCB (PCB4) copyir.com Check if appropriate voltages are applied to the Duplex Driver side (12V to 1pin, 5V to 3pin, 3 copyir.com3V to 4pin) copyir.com -> If not, replace the DC-DC Converter PCB copyir.com 4 copyir.com Replace the Duplex Driver PCB (PCB4) copyir.com 5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E197-0004 Error in Relay PCB connection detection
Connection between the DC Controller PCB (PCB1) and the Relay PCB (PCB5) is disconnected copyir.com 1 copyir.com Check the connection of the DC Controller PCB (PCB1) and the Relay PCB (PCB5) copyir.com DC Controller side: J451, Relay side: J514 2 copyir.com Replace the Relay PCB (PCB5) copyir.com 3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E197-0005 Error in Main Driver PCB Analog Connector connection detection
Connection between the DC Controller PCB (PCB1) and the Main Driver PCB (PCB2) is disconnected copyir.com 1 copyir.com Check the connection of the DC Controller PCB (PCB1) and the Main Driver PCB (PCB2) copyir.com DC Controller side: J413, Main Driver side: J124 2 copyir.com Replace the Main Driver PCB (PCB2) copyir.com 3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E197-0006 Error in Feed Driver PCB Drawer Connector connection detection
Connection between the DC Controller PCB (PCB1) and the Feed Driver PCB (PCB3) is disconnected copyir.com 1 copyir.com Check the connection between the DC Controller PCB (PCB1) and the Fixing Feed Drawer copyir.com DC Controller side: J431, J432, Fixing Feed Drawer (host machine side): J3002D Fixing Feed Drawer (Fixing Feed side): J3002L, Feed Driver side: J300, J301 2 copyir.com Replace the Feed Driver PCB (PCB3) copyir.com 3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E197-0008 Error in Fixing Drawer Connector connection detection
Connection between the DC Controller PCB (PCB1) and the Main Driver PCB (PCB2) is disconnected copyir.com 1 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Fixing Drawer copyir.com Main Driver side: J105, Fixing Drawer (host machine side): J3001D Check the Harness of the Fixing Drawer (Fixing side) (J3001L) copyir.com 2 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E197-0009 Error in the Process Unit connection detection
Connection between the Main Driver PCB (PCB2) and the Process Unit is disconnected copyir.com 1 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Process Unit copyir.com PCB side: J107, Process Unit side: J3060 2 copyir.com Replace the Process Unit copyir.com
E197-0010 Error in Primary Charging High Voltage PCB connection detection
Connection between the Main Driver PCB (PCB2) and the Primary Charging High Voltage PCB (PCB11) is disconnected copyir.com 1 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Primary Charging High Voltage PCB (PCB11) copyir.com Main Driver side: J111, Primary Charging High Voltage side: J3501 2 copyir.com Replace the Primary Charging High Voltage PCB (PCB11) copyir.com
E197-0011 Error in Developing High Voltage PCB connection detection
Connection between the Main Driver PCB (PCB2) and the Developing High Voltage PCB (PCB12) is disconnected copyir.com 1 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Developing High Voltage PCB (PCB12) copyir.com Main Driver side: J112, Developing High Voltage side: J3511 2 copyir.com Replace the Developing High Voltage PCB (PCB12) copyir.com
E197-0012 Error in Transfer High Voltage PCB connection detection
Connection between the Duplex Driver PCB (PCB4) and the Transfer High Voltage PCB (PCB13) is disconnected copyir.com 1 copyir.com Check the connection between the Duplex Driver PCB (PCB4) and the Transfer High Voltage PCB (PCB13) copyir.com Duplex Driver side: J343, Transfer High Voltage side: J3062 2 copyir.com Replace the Transfer High Voltage PCB (PCB13) copyir.com
E197-0181 Serial communication error
Failure of reception from the video signal control ASIC copyir.com Data reception was failed 5 times in a row when reading data from the video signal control ASIC (at FG lock detection, BD lock detection) copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E202-0001 Scanner HP error
An error occurs during the Scanner Unit (Paper Front) HP detection operation (outward) copyir.com 1 copyir.com Connector disconnection/open circuit of the Scanner HP Sensor (SR2) copyir.com 2 copyir.com Failure of the Scanner HP Sensor (SR2) copyir.com 3 copyir.com Failure of the Scanner Motor (M1) copyir.com 4 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E202-0002 Scanner HP error
An error occurs during the Scanner Unit (Paper Front) HP detection operation (homeward) copyir.com 1 copyir.com Connector disconnection/open circuit of the Scanner HP Sensor (SR2) copyir.com 2 copyir.com Failure of the Scanner HP Sensor (SR2) copyir.com 3 copyir.com Failure of the Scanner Motor (M1) copyir.com 4 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E202-0101 Glass HP error
An error occurs during the Glass HP detection operation (outward) copyir.com 1 copyir.com Connector disconnection/open circuit of the Glass Shift HP Sensor (SR11) copyir.com 2 copyir.com Failure of the Glass Shift HP Sensor (SR11) copyir.com 3 copyir.com Failure of the Glass Shift Motor (M9) copyir.com 4 copyir.com Failure of the DADF Driver PCB (PCB1) copyir.com
E202-0102 Glass HP error
An error occurs during the Glass HP detection operation (homeward) copyir.com 1 copyir.com Connector disconnection/open circuit of the Glass Shift HP Sensor (SR11) copyir.com 2 copyir.com Failure of the Glass Shift HP Sensor (SR11) copyir.com 3 copyir.com Failure of the Glass Shift Motor (M9) copyir.com 4 copyir.com Failure of the DADF Driver PCB (PCB1) copyir.com
E227-0001 Power supply (24V) error
24V port is OFF when the power is turned ON copyir.comB 1 copyir.com Connector disconnection/open circuit of the Reader Power Supply copyir.com 2 copyir.com Failure of power supply copyir.com
E227-0002 Power supply (24V) error
24V port is OFF when a job is started copyir.com 1 copyir.com Connector disconnection/open circuit of the Reader Power Supply copyir.com 2 copyir.com Failure of power supply copyir.com
E227-0003 Power supply (24V) error
24V port is OFF when a job is ended copyir.com 1 copyir.com Connector disconnection/open circuit of the Reader Power Supply copyir.com 2 copyir.com Failure of power supply
E227-0004 Power supply (24V) error
24V port is OFF when loading copyir.com 1 copyir.com Connector disconnection/open circuit of the Reader Power Supply copyir.com 2 copyir.com Failure of power supply copyir.com
E227-0101 Power supply (24V) error
24V port is OFF when the power of DADF is turned ON copyir.com 1 copyir.com Connection error between the DADF Driver PCB (PCB1) and the Reader Controller PCB (PCB1) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Power Supply copyir.com 3 copyir.com Failure of power supply copyir.com
E227-0102 Power supply (24V) error
24V port is OFF when a job is started in the DADF copyir.com 1 copyir.com Connection error between the DADF Driver PCB (PCB1) and the Reader Controller PCB (PCB1) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Power Supply copyir.com 3 copyir.com Failure of power supply copyir.com
E227-0103 Power supply (24V) error
24V port is OFF when a job is ended in the DADF copyir.com 1 copyir.com Connection error between the DADF Driver PCB (PCB1) and the Reader Controller PCB (PCB1) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Power Supply copyir.com 3 copyir.com Failure of power supply copyir.com
E240-0000 Communication error between Main Controller and DC Controller
Communication error occurs between the CPU of the Main Controller PCB and the DC Controller PCB (PCB1) copyir.com 1 copyir.com Check the connection of the Main Controller PCB and the DC Controller PCB (PCB1) copyir.com Main Controller side: J712, DC Controller side: J442 2 copyir.com Replace the DC Controller PCB (PCB1) copyir.com 3 copyir.com Replace the Main Controller PCB copyir.com
E240-0001 3 minutes passed with pickup request waiting status
It was detected that 3 minutes passed with pickup request waiting status copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Check the connection of the Sub PCB in the Main Controller PCB 1 Box copyir.com 3 copyir.com Check the connections of the DC Controller PCB and the Main Controller PCB 1 copyir.com Replace the PCB(s) if necessary copyir.com
E240-0002 3 minutes passed with image output request waiting status
It was detected that 3 minutes passed with image output request waiting status copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Check the connection of the Sub PCB in the Main Controller PCB 1 Box copyir.com 3 copyir.com Check the connections of the DC Controller PCB and the Main Controller PCB 1 copyir.com Replace the PCB(s) if necessary copyir.com
E240-0003 Software sequence error after the jam
A software sequence error (engine bug) was detected after the jam copyir.com? 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Check the connection of the Sub PCB in the Main Controller PCB 1 Box copyir.com 3 copyir.com Check the connections of the DC Controller PCB and the Main Controller PCB 1 copyir.com Replace the PCB(s) if necessary copyir.com
E246 System error Contact to the sales companies copyir.com
E247 System error Contact to the sales companies copyir.com
E248-0000 SRAM error
SRAM check error when the power is turned ON copyir.com Main Controller PCB 2 copyir.com
E248-0001 EEPROM error
An error when EEPROM power for the Reader Controller PCB (PCB1) is turned ON copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E248-0002 EEPROM error
EEPROM writing error for the Reader Controller PCB (PCB1) copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E248-0003 EEPROM error
Reading error after writing to EEPROM for the Reader Controller PCB (PCB1) copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E263-0000 Error in Current Sensor reference voltage generation
The reference voltage is not within the range of reference value copyir.com 1 copyir.com Check the connection between the AC Driver PCB and the Main Driver PCB (connector disconnection, open circuit, short circuit of harness) copyir.com AC Driver side: J615, Main Driver side: J103 2 copyir.com Replace the AC Driver PCB copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E263-0001 Current Sensor error
An error is detected in the value of the Current Sensor (SE601) (the value remains at the upper limit) copyir.com 1 copyir.com Check the connection between the AC Driver PCB and the Main Driver PCB (connector disconnection, open circuit, short circuit of harness) copyir.com AC Driver side: J615, Main Driver side: J103 2 copyir.com Replace the AC Driver PCB copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E263-0002 Current Sensor error
An error is detected in the value of the Current Sensor (SE601) (the value remains at the lower limit) copyir.com 1 copyir.com Check the connection between the AC Driver PCB and the Main Driver PCB (connector disconnection, open circuit, short circuit of harness) copyir.com AC Driver side: J615, Main Driver side: J103 2 copyir.com Replace the AC Driver PCB copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E263-0003 Error in Current Sensor accuracy
The value of the Current Sensor (SE601) is not within the range of reference value copyir.com 1 copyir.com Check the connection between the AC Driver PCB and the Main Driver PCB (connector disconnection, open circuit, short circuit of harness) copyir.com AC Driver side: J615, Main Driver side: J103 2 copyir.com Replace the AC Driver PCB copyir.com 3 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E270-0001 Error in paper front vertical scanning synchronous signal
Vertical scanning synchronous signal (VSYNC) is not sent appropriately from the CMOS PCB (Scanner Unit (Paper Front)), so the image error occurs or the operation stops abnormally copyir.com 1 copyir.com Connector disconnection/open circuit of the Scanner Unit (Reader) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the Scanner Unit (Reader) copyir.com 4 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E270-0002 Error in horizontal scanning/vertical scanning synchronous signal
Due to the horizontal scanning synchronous signal (HSYNC) error, the vertical scanning synchronous signal (VSYNC) is not sent, so the image error occurs or the operation stops abnormally copyir.com 1 copyir.com Connector disconnection/open circuit of the Scanner Unit (Reader/DADF) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the Scanner Unit (Reader/DADF) copyir.com 4 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E270-0101 Error in paper back vertical scanning synchronous signal
Vertical scanning synchronous signal (VSYNC) is not sent appropriately from the CMOS PCB (Scanner Unit (Paper Back)), so the image error occurs or the operation stops abnormally copyir.com 1 copyir.com Connector disconnection/open circuit of the Scanner Unit (DADF) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the Scanner Unit (DADF) copyir.com 4 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E280-0001 Communication error between Reader Controller PCB (PCB1) and Scanner Unit (Reader)
Within the specified period of time, communication between the Reader Controller PCB and Scanner Unit (Paper Front) is not started copyir.com 1 copyir.com Connector disconnection/open circuit of the Scanner Unit (Reader) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the Scanner Unit (Reader) copyir.com 4 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E280-0101 Communication error between Reader Controller PCB (PCB1) and Scanner Unit (DADF)
Within the specified period of time, communication between the Reader Controller PCB and Scanner Unit (Paper Back) is not started copyir.com 1 copyir.com Connector disconnection/open circuit of the Scanner Unit (DADF) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the Scanner Unit (DADF) copyir.com 4 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E301-0001 Paper front light intensity NG
Light intensity is below the reference level at paper front shading copyir.com Failure of the Scanner Unit (Reader) copyir.com
E301-0101 Paper back light intensity NG
Light intensity is below the reference level at paper back shading copyir.com Failure of the Scanner Unit (DADF) copyir.com
E302-0001 Error in paper front shading copyir.com
Error in shading RAM access, or the shading value is either below or higher than the reference level copyir.com 1 copyir.com Connector disconnection/open circuit of the Scanner Unit (Reader) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the Scanner Unit (Reader) copyir.com 4 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E302-0101 Error in paper back shading
Error in shading RAM access, or the shading value is either below or higher than the reference level copyir.com 1 copyir.com Connector disconnection/open circuit of the Scanner Unit (DADF) copyir.com 2 copyir.com Connector disconnection/open circuit of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Operation error of the Glass Shift Motor (M9) copyir.com 4 copyir.com Failure of the Scanner Unit (DADF) copyir.com 5 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E315 Codec error
E350 System error Contact to the sales companies copyir.com
E351-0000 Main Controller PCB 2 communication error
Main Controller PCB 2 communication error copyir.com 1 copyir.com Disconnect and then connect the connector of the Main Controller PCB 2 copyir.com 2 copyir.com Replace the Main Controller PCB 2 copyir.com
E354 System error Contact to the sales companies copyir.com
E355 System error Contact to the sales companies copyir.com
E400-0001 Communication error between Reader Controller PCB (PCB1) and DADF
Reception error occurs at the time of communication between the Reader Controller PCB and the DADF 1 copyir.com Connection error between the DADF Driver PCB (PCB1) and the Reader Controller PCB (PCB1) copyir.com 2 copyir.com Failure of the DADF Driver PCB (PCB1) copyir.com 3 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E400-0002 Communication error between Reader Controller PCB (PCB1) and DADF
Reception error occurs at the time of communication between the Reader Controller PCB and the DADF copyir.com 1 copyir.com Connection error between the DADF Driver PCB (PCB1) and the Reader Controller PCB (PCB1) copyir.com 2 copyir.com Failure of the DADF Driver PCB (PCB1) copyir.com 3 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com
E401-0001 Pickup Roller Unit lifting error
The level of the Pickup Roller Unit Lifter HP Sensor (SR12) does not change within the specified period of time although the Pickup Roller Unit Lifter Motor (M10) is driven copyir.com 1 copyir.com Connector disconnection/open circuit of the Pickup Roller Unit Lifter HP Sensor (SR12) copyir.com 2 copyir.com Connector disconnection/open circuit of the Pickup Roller Unit Lifter Motor (M10) copyir.com 3 copyir.com Failure of the Pickup Roller Unit Lifter HP Sensor (SR12) copyir.com 4 copyir.com Failure of the Pickup Roller Unit Lifter Motor (M10) copyir.com
E401-0002 Pickup Roller Unit lifting error
The level of the Pickup Roller Unit Lifter HP Sensor (SR12) does not change within the specified period of time although the Pickup Roller Unit Lifter Motor (M10) is driven copyir.com 1 copyir.com Connector disconnection/open circuit of the Pickup Roller Unit Lifter HP Sensor (SR12) copyir.com 2 copyir.com Connector disconnection/open circuit of the Pickup Roller Unit Lifter Motor (M10) copyir.com 3 copyir.com Failure of the Pickup Roller Unit Lifter HP Sensor (SR12) copyir.com 4 copyir.com Failure of the Pickup Roller Unit Lifter Motor (M10) copyir.com
E407-0001 Tray Lifter Motor (M8) error
The Tray HP Sensor (SR13) is not turned ON or OFF within the specified period of time although the Tray Lifter Motor (M8) is driven copyir.com 1 copyir.com Connector disconnection/open circuit of the Tray HP Sensor (SR13) copyir.com 2 copyir.com Connector disconnection/open circuit of the Tray Lifter Motor (M8) copyir.com 3 copyir.com Failure of the Tray HP Sensor (SR13) copyir.com 4 copyir.com Failure of the Tray Lifter Motor (M8) copyir.com
E407-0002 Tray Lifter Motor (M8) error
The Paper Surface Sensor (SR6) is not turned ON within the specified period of time although the Tray Lifter Motor (M8) is driven copyir.com 1 copyir.com Connector disconnection/open circuit of the Paper Surface Sensor (SR6) copyir.com 2 copyir.com Connector disconnection/open circuit of the Tray Lifter Motor (M8) copyir.com 3 copyir.com Failure of the Paper Face Sensor (SR6) copyir.com 4 copyir.com Failure of the Tray Lifter Motor (M8) copyir.com
E413-0001 DADF Disengagement Motor 1 (M6) error
The DADF Disengagement HP Sensor 1 (SR15) is not turned ON within the specified period of time although the DADF Disengagement Motor 1 (M6) is driven copyir.com 1 copyir.com Connector disconnection/open circuit of the Disengagement HP Sensor 1 (SR15) copyir.com 2 copyir.com Connector disconnection/open circuit of the Disengagement Motor 1 (M6) copyir.com 3 copyir.com Failure of the Disengagement HP Sensor 1 (SR15) copyir.com 4 copyir.com Failure of the Disengagement Motor 1 (M6) copyir.com 5 copyir.com Failure of the DADF Driver PCB (PCB1) copyir.com
E413-0002 DADF Disengagement Motor 1 (M6) error
The DADF Disengagement HP Sensor 1 (SR15) is not turned OFF within the specified period of time although the DADF Disengagement Motor 1 (M6) is driven copyir.com 1 copyir.com Connector disconnection/open circuit of the Disengagement HP Sensor 1 (SR15) copyir.com 2 copyir.com Connector disconnection/open circuit of the Disengagement Motor 1 (M6) copyir.com 3 copyir.com Failure of the Disengagement HP Sensor 1 (SR15) copyir.com 4 copyir.com Failure of the Disengagement Motor 1 (M6) copyir.com 5 copyir.com Failure of the DADF Driver PCB (PCB1) copyir.com
E413-0011 DADF Disengagement Motor 2 (M7) error
The DADF Disengagement HP Sensor 2 (SR16) is not turned ON within the specified period of time although the DADF Disengagement Motor 2 (M7) is driven copyir.com 1 copyir.com Connector disconnection/open circuit of the Disengagement HP Sensor 2 (SR16) copyir.com 2 copyir.com Connector disconnection/open circuit of the Disengagement Motor 2 (M7) copyir.com 3 copyir.com Failure of the Disengagement HP Sensor 2 (SR16) copyir.com 4 copyir.com Failure of the Disengagement Motor 2 (M7) copyir.com 5 copyir.com Failure of the DADF Driver PCB (PCB1) copyir.com
E413-0012 DADF Disengagement Motor 2 (M7) error
The DADF Disengagement HP Sensor 2 (SR16) is not turned OFF within the specified period of time although the DADF Disengagement Motor 2 (M7) is driven copyir.com 1 copyir.com Connector disconnection/open circuit of the Disengagement HP Sensor 2 (SR16) copyir.com 2 copyir.com Connector disconnection/open circuit of the Disengagement Motor 2 (M7) copyir.com 3 copyir.com Failure of the Disengagement HP Sensor 2 (SR16) copyir.com 4 copyir.com Failure of the Disengagement Motor 2 (M7) copyir.com 5 copyir.com Failure of the DADF Driver PCB (PCB1) copyir.com
E423-0001 DADF SDRAM error
SDRAM access error copyir.com Error in SDRAM (video image memory) on the Reader Controller PCB (PCB1) copyir.com
E423-0002 DADF SDRAM erroror copyir.com
SDRAM Verify error copyir.com Error in SDRAM (video image memory) on the Reader Controller PCB (PCB1) copyir.com
E490-0001 Different DADF model error
Not proper DADF is installed copyir.com 1 copyir.com Installed DADF is a different model copyir.com 2 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the DC Controller PCB copyir.com 4 copyir.com Failure of the Main Controller PCB copyir.com
E500-0000 Communication error (Finisher-E1)
The communication with the host machine is interrupted copyir.com 1 copyir.com The Finisher Controller PCB is faulty copyir.com 2 copyir.com The host machine DC Controller PCB is faulty copyir.com
E503-0002 Communication error (Finisher-E1)
The communication with the Saddle Stitcher is interrupted copyir.com 1 copyir.com The wiring between the Finisher Controller PCB and Saddle Controller PCB is faulty copyir.com 2 copyir.com The Finisher Controller PCB is faulty copyir.com 3 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E503-0003 Communication error (Finisher-E1/External 2 Hole Puncher)
The communication with the Puncher unit is interrupted copyir.com 1 copyir.com The wiring between the Finisher Controller PCB and host machine DC Controller PCB is faulty copyir.com 2 copyir.com The Punch Controller PCB is faulty copyir.com 3 copyir.com The Finisher Controller PCB is faulty copyir.com 4 copyir.com The host machine DC Controller PCB is faulty copyir.com
E503-0004 A copyir.com Communication error (Finisher-E1) B copyir.com Communication error with Insertion Unit (Document Insertion Unit-L1) C copyir.com Communication error with Insertion Unit (Document Insertion/Folding Unit-H1)
A copyir.com The communication with the Inserter or the Paper Folding Unit is interrupted copyir.com B copyir.com Failed communication for 3 consecutive times copyir.com C copyir.com Failed communication for 3 consecutive times copyir.com A-1 copyir.com The wiring between the Finisher Controller PCB and host machine Controller PCB is faulty copyir.com A-2 copyir.com The Finisher Controller PCB is faulty copyir.com A-3 copyir.com The host machine Controller PCB is faulty copyir.com B-1 copyir.com Inserter Controller PCB is faulty copyir.com B-2 copyir.com Disconnection of communication cable B-3 copyir.com Connector on the Inserter Controller PCB is disconnected copyir.com C-1 copyir.com Folder Controller PCB is faulty copyir.com C-2 copyir.com Disconnection of communication cable C-3 copyir.com Connector on the DC Controller PCB is disconnected copyir.com
E505-0001 Finisher back-up RAM (EEPROM) error (Finisher-D1/E1)
The checksum for the EEPROM data has an error copyir.com (The value written in EEPROM and the value extracted from EEPROM doesn’t conform copyir.com) The Finisher Controller PCB is faulty copyir.com
E505-0002 EEPROM error (External 2 Hole Puncher)
The checksum for the EEPROM data has an error copyir.com The Punch Controller PCB is faulty copyir.com
E505-0003 A copyir.com EEPROM error with the Insertion Unit (failed data reading/ writing) (Document Insertion Unit-L1) B copyir.com EEPROM error with the Insertion Unit (failed data reading/ writing) (Document Insertion/Folding Unit-H1)
A copyir.com The checksum for the EEPROM data has an error copyir.com B copyir.com Data failed to be read properly copyir.com A copyir.com The Insertion Unit Controller PCB is faulty copyir.com B copyir.com Folder Controller PCB is faulty copyir.com
E514-8001 Rear end assist home position error (Finisher-E1)
The stapler does not leave the rear end assist home position when the Rear Eend Assist Motor has been driven for 3 seconds copyir.com 1 copyir.com The Rear End Assist Home Position Sensor (PI109) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Rear End Assist Motor is faulty copyir.com 3 copyir.com The end assist mechanism is faulty copyir.com 4 copyir.com The Rear End Assist Motor (M109) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E514-8002 Rear end assist home position error (Finisher-E1)
The stapler does not return to the rear end assist home position when the Rear End Assist Motor has been driven for 3 seconds copyir.comm copyir.com) 1 copyir.com The Rear End Assist Home Pposition Sensor (PI109) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Rear End Assist Motor is faulty copyir.com 3 copyir.com The end assist mechanism is faulty copyir.com 4 copyir.com The Rear End Assist Motor (M109) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E518-8001 Error in Folding Feed Motor lock (Document Insertion/Folding Unit-H1)
The Folding Feed Motor (M5) lock signal has been detected for more than the specified time copyir.com 1 copyir.com Connector of the Folding Feed Motor (M5) is disconnected copyir.com 2 copyir.com Folding Feed Motor (M5) is faulty copyir.com
E519-0002 Gear change home position error (Finisher-E1)
The Gear Change Hhome Position Sensor does not turn ON when the Gear Change Motor has been driven for 387 pulses copyir.com 1 copyir.com The Gear Change Home Position Sensor (PI117) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Gear Change Motor is faulty copyir.com 3 copyir.com The gear change mechanism is faulty copyir.com 4 copyir.com The Gear Change Motor (M110) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E519-8001 Gear change home position error (Finisher-E1)
The Gear Change Home Position Sensor does not turn OFF when the Gear Change Motor has been driven for 387 pulses copyir.com 1 copyir.com The Gear Change Home Position Sensor (PI117) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Gear Change Motor is faulty copyir.com 3 copyir.com The gear change mechanism is faulty copyir.com 4 copyir.com The Gear Change Motor (M110) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E530-8001 Front aligning plate home position error (Finisher-E1)
The aligning plate does not leave the Aligning Plate Front Home Position Sensor when the Alignment Plate Front Motor has been driven for 4 seconds copyir.com 1 copyir.com The Front Aligning Plate Home Position Sensor (PI106) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Front Aligning Plate Motor is faulty copyir.com 3 copyir.com The front aligning plate is faulty copyir.com 4 copyir.com The Front Aligning Plate Motor (M103) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E530-8002 Front aligning plate home position error (Finisher-E1)
The aligning plate does not return to aligning plate front home position Sensor when the alignment plate front Motor has been driven for 4 seconds copyir.com 1 copyir.com The front Aligning Plate Home Position Sensor (PI106) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and front aligning plate Motor is faulty copyir.com 3 copyir.com The front aligning plate is faulty copyir.com 4 copyir.com The front aligning plate Motor (M103) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E531-8001 Staple home position error (Finisher-E1)
The Stapler does not leave the staple home position when the Staple Motor has been driven for 0 copyir.com4 sec copyir.com 1 copyir.com The wiring between the Finisher Controller PCB and Stapler is faulty copyir.com 2 copyir.com The Stapler is faulty copyir.com 3 copyir.com The Finisher Controller PCB is faulty copyir.com
E531-8002 Staple home position error (Finisher-E1)
The Stapler does not return to the staple home position when the Staple Motor has been driven for 0 copyir.com4 sec copyir.com 1 copyir.com The wiring between the Finisher Controller PCB and Stapler is faulty copyir.com 2 copyir.com The Stapler is faulty copyir.com 3 copyir.com The Finisher Controller PCB is faulty copyir.com
E532-8001 Stapler shift home position error (Finisher-E1)
The Stapler does not leave the stapler shift home pposition when the Stapler Shift Motor hasbeen driven for 5 seconds copyir.com 1 copyir.com The Stapler Drive Home Position Sensor (PI110) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Stapler Shift Motor is faulty copyir.com 3 copyir.com The stapler shift base is faulty copyir.com 4 copyir.com The Stapler Shift Motor (M105) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E532-8002 Stapler shift home position error (Finisher-E1)
The Stapler does not return to the stapler shift home position when the Stapler Shift Motor has been driven for 20 seconds copyir.com 1 copyir.com The Stapler Drive Home Position Sensor (PI110) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Stapler Shift Motor is faulty copyir.com 3 copyir.com The stapler shift base is faulty copyir.com 4 copyir.com The Stapler Shift Motor (M105) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E535-8001 Swing home position error (Finisher-E1)
The Stapler does not leave the swing home position when the Swing Motor has been driven for 3 seconds copyir.com 1 copyir.com The Swing Home Position Sensor (PI105) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Swing Motor is faulty copyir.com 3 copyir.com The swing mechanism is faulty copyir.com 4 copyir.com The Swing Motor (M106) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E535-8002 Swing home position error (Finisher-E1)
The Stapler does not return to the swing home position when the Swing Motor has bee driven for 3 seconds copyir.com 1 copyir.com The Swing Home Position Sensor (PI105) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Swing Motor is faulty copyir.com 3 copyir.com The swing mechanism is faulty copyir.com 4 copyir.com The Swing Motor (M106) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E537-8001 Rear aligning plate home position error (Finisher-E1)
The aligning plate does not leave the Aligning Plate Rear Home Position Sensor when the Alignment Plate Rear Motor has been driven for 4 seconds copyir.com 1 copyir.com The Aligning Plate Rear Home Position Sensor (PI107) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Aligning Plate Rear Motor is faulty copyir.com 3 copyir.com The rear aligning plate is faulty copyir.com 4 copyir.com The Rear Aligning Plate Motor (M104) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E537-8002 Rear aligning plate home position error (Finisher-E1)
The aligning plate does not return to Aligning Plate Rear Home Position Sensor when the Alignment Plate Rear Motor has been driven for 4 seconds copyir.com 1 copyir.com The Aligning Plate Rear Home Position Sensor (PI107) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Aligning Plate Rear Motor is faulty copyir.com 3 copyir.com The rear aligning plate is faulty copyir.com 4 copyir.com The Rear Aligning Plate Motor (M104) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E540-8001 Tray 1 time out error (Finisher-E1)
1 copyir.com If the tray does not return to home position when the Tray 1 Shift Motor is driven for 25 seconds copyir.com 2 copyir.com If the tray does not move to other area when Tray 1 Shift Motor is driven for 5 seconds copyir.com 1 copyir.com The Tray 1 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 1 Shift Motor (M107) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E540-8002 Tray 1 shift area error (Finisher-E1)
1 copyir.com The dangerous area is reached before the Tray 1 Paper Surface Sensor detects paper surface during the paper surface detection operation copyir.com 2 copyir.com A discontinuous area is detected during tray operation copyir.com 1 copyir.com The Tray 1 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 1 Shift Motor (M107) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E540-8003 Swing Guide Switch/Staple Safety Switch error (Finisher-E1)
The swing guide switch or staple safety switch is activated while the tray is operating copyir.com 1 copyir.com The Tray 1 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 1 Shift Motor (M107) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E540-8004 The Tray 1 Shift Motor clock error (Finisher-E1)
The FG input cannot be detected when the Tray 1 Shift Motor has been driven for 0 copyir.com2 second copyir.com 1 copyir.com The Tray 1 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 1 Shift Motor (M107) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty
E540-8005 The Tray 1 Shift Motor speed error (Finisher-E1)
The lock detection signal turns OFF 150 msec after the lock detection signal turned ON copyir.com 1 copyir.com The Tray 1 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 1 Shift Motor (M107) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E540-8006 The Tray 1 Shift Motor acceleration error (Finisher-E1)
The lock detection signal does not turn ON when the Tray 1 Shift Motor has been driven for 1 second copyir.com 1 copyir.com The Tray 1 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 1 Shift Motor (M107) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E540-8007 The Tray 1 Shift Motor error (Finisher-E1)
The lock detection signal does not turn OFF when the Tray 1 Shift Motor is at a stop copyir.com 1 copyir.com The Tray 1 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 1 Shift Motor (M107) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E542-8001 Tray 1 time out error (Finisher-E1)
1 copyir.com If the tray does not return to home position when the Tray 1 Shift Motor is driven for 25 seconds copyir.com 2 copyir.com If the tray does not move to other area when Tray 2 Shift Motor is driven for 5 seconds copyir.com 1 copyir.com The Tray 2 shift area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 2 shift Motor (M105) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E542-8002 Tray 2 shift area error (Finisher-E1)
1 copyir.com The upper limit area is reached before the Tray 2 Paper Surface Sensor 1 detects the paper surface during paper surface detection operation copyir.com 2 copyir.com A discontinuous area is detected during tray operation copyir.com 3 copyir.com During evacuation operation, arrival at the area beyond the Tray 2 Paper Surface Sensor 2 is detected before this Sensor detects paper surface copyir.com 1 copyir.com The Tray 2 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 2 Shift Motor (M105) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E542-8004 The Tray 2 Shift Motor clock error (Finisher-E1)
The FG input cannot be detected when the Tray 2 Shift Motor has been driven for 0 copyir.com2 second copyir.com 1 copyir.com The Tray 2 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 2 Shift Motor (M105) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E542-8005 The Tray 2 Shift Motor speed error (Finisher-E1)
The lock detection signal turns OFF 150 msec after the lock detection signal turned ON copyir.com 1 copyir.com The Tray 2 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 2 Shift Motor (M105) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E542-8006 The Tray 2 Shift Motor acceleration error (Finisher-E1)
The lock detection signal does not turn ON when the Tray 2 Shift Motor has been driven for 1 second copyir.com 1 copyir.com The Tray 2 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 2 Shift Motor (M105) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E542-8007 The Tray 2 Shift Motor error (Finisher-E1)
The lock detection signal does not turn OFF when the Tray 2 Shift Motor is at a stop copyir.com 1 copyir.com The Tray 2 Shift Area Sensor PCB is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty copyir.com 3 copyir.com The tray up/down mechanism is faulty copyir.com 4 copyir.com The Tray 2 Shift Motor (M105) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E551-0011 Error in the Power Supply Fan of the Insertion Unit
The loch signal is detected for the specified times while the fan operates copyir.com 1 copyir.com The connector of the Fan (F1) is disconnected copyir.com 2 copyir.com The wiring of the Fan (F1) is faulty copyir.com 3 copyir.com The Fan (F1) is faulty copyir.com 4 copyir.com The Insertion Unit Controller PCB is faulty copyir.com
E551-0021 Error in the Power Supply Fan of the Paper Folding Unit
The loch signal is detected for the specified times while the fan operates copyir.com 1 copyir.com The connector of the Fan (F1) is disconnected copyir.com 2 copyir.com The wiring of the Fan (F1) is faulty copyir.com 3 copyir.com The Fan (F1) is faulty copyir.com 4 copyir.com The Paper Folding Unit Controller PCB is faulty copyir.com
E562-8001 Error in Slowing Timing Sensor (Document Insertion/Folding Unit-H1)
The receiving-light intensity failed to be within the threshold although the emitting-light intensity is adjusted to be within the threshold when adjusting the Sensor copyir.com 1 copyir.com Connector of the Slowing Timing Sensor (S24) is disconnected copyir.com 2 copyir.com Slowing Timing Sensor (S24) is faulty copyir.com
E562-8002 Error in Disengagement Timing Sensor (Document Insertion/ Folding Unit-H1) copyir.com
The receiving-light intensity failed to be within the threshold although the emitting-light intensity is adjusted to be within the threshold when adjusting the Sensor copyir.com 1 copyir.com Connector of the Disengagement Timing Sensor (S21) is disconnected copyir.com 2 copyir.com Disengagement Timing Sensor (S21) is faulty copyir.com
E562-8003 Error in Folding Position Accuracy Sensor (Document Insertion/Folding Unit-H1)
The receiving-light intensity failed to be within the threshold although the emitting-light intensity is adjusted to be within the threshold when adjusting the Sensor copyir.com 1 copyir.com Connector of the Folding Position Accuracy Sensor (S23) is disconnected copyir.com 2 copyir.com Folding Position Accuracy Sensor (S23) is faulty copyir.com
E562-8004 Error in the Upper Stopper HP Sensor (Document Insertion/ Folding Unit-H1)
1 copyir.com Connector of the Upper Stopper HP Sensor (S16) is disconnected copyir.com 2 copyir.com Upper Stopper HP Sensor (S16) is faulty copyir.com The receiving-light intensity failed to be within the threshold although the emitting-light intensity is adjusted to be within the threshold when adjusting the Sensor copyir.com
E569-8001 Upper Stopper Motor of Paper Folding Unit failed to go through HP (Document Insertion/Folding Unit-H1)
The Upper Stopper HP Sensor failed to be OFF despite the drive of specified pulse in the case that the Upper Stopper Motor started to be driven while the Upper Stopper HP Sensor was ON copyir.com 1 copyir.com Connector of the Upper Stopper Motor (M7) is disconnected copyir.com 2 copyir.com Upper Stopper Motor (M7) is faulty copyir.com 3 copyir.com Connector of the Upper Stopper HP Sensor (S16) is disconnected copyir.com 4 copyir.com Upper Stopper HP Sensor (S16) is faulty copyir.com
E569-8002 Upper Stopper Motor of Paper Folding Unit failed to return to HP (Document Insertion/Folding Unit-H1)
The Upper Stopper HP Sensor failed to be ON despite the drive of specified pulse in the case that the Upper Stopper Motor started to be driven while the Upper Stopper HP Sensor was OFF copyir.com 1 copyir.com Connector of the Upper Stopper Motor (M7) is disconnected copyir.com 2 copyir.com Upper Stopper Motor (M7) is faulty copyir.com 3 copyir.com Connector of the Upper Stopper HP Sensor (S16) is disconnected copyir.com 4 copyir.com Upper Stopper HP Sensor (S16) is faulty copyir.com
E56A-8001 C-fold Stopper Motor of Paper Folding Unit failed to go through HP (Document Insertion/Folding Unit-H1)
The C-fold Stopper Motor HP Sensor failed to be OFF despite the drive of specified pulse in the case that the C-fold Stopper Motor started to be driven while the C-fold Stopper Motor HP Sensor was ON copyir.com 1 copyir.com Connector of the C-fold Stopper Motor (M8) is disconnected copyir.com 2 copyir.com C-fold Stopper Motor (M8) is faulty copyir.com 3 copyir.com Connector of the C-fold Stopper HP Sensor (S17) is disconnected copyir.com 4 copyir.com C-fold Stopper HP Sensor (S17) is faulty copyir.com
E56A-8002 C-fold Stopper Motor of Paper Folding Unit failed to return to HP (Document Insertion/Folding Unit-H1)
The C-fold Stopper Motor HP Sensor failed to be ON despite the drive of specified pulse in the case that the C-fold Stopper Motor started to be driven while the C-fold Stopper Motor HP Sensor was OFF copyir.com 1 copyir.com Connector of the C-fold Stopper Motor (M8) is disconnected copyir.com 2 copyir.com C-fold Stopper Motor (M8) is faulty copyir.com 3 copyir.com Connector of the C-fold Stopper HP Sensor (S17) is disconnected copyir.com 4 copyir.com C-fold Stopper HP Sensor (S17) is faulty copyir.com
E56B-8001 C-fold Tray Motor of Paper Folding Unit failed to go through HP (Document Insertion/Folding Unit-H1)
The C-fold Tray Motor Sensor failed to be OFF despite the drive of specified pulse in the case that the C-fold Tray Motor started to be driven while the C-fold Tray Motor Sensor was ON copyir.com 1 copyir.com Connector of the C-fold Tray Motor (M6) is disconnected 2 copyir.com C-fold Tray Motor (M6) is faulty 3 copyir.com Connector of the C-fold Tray Motor Sensor (S19) is disconnected 4 copyir.com C-fold Tray Motor Sensor (S19) is faulty
E56B-8002 Folding Tray Motor of Paper Folding Unit failed to return to HP (Document Insertion/Folding Unit-H1)
The C-fold Tray Motor Sensor failed to be ON despite the drive of specified pulse in the case that the C-fold Tray Motor started to be driven while the C-fold Tray Motor Sensor was OFF copyir.comenso 1 copyir.com Connector of the C-fold Tray Motor (M6) is disconnected copyir.com 2 copyir.com C-fold Tray Motor (M6) is faulty copyir.com 3 copyir.com Connector of the C-fold Tray Motor Sensor (S19) is disconnected copyir.com 4 copyir.com C-fold Tray Motor Sensor (S19) is faulty copyir.com
E584-0002 Shutter home position error (Finisher-E1)
The stapler does not return to the shutter home position when the Stack Ejection Motor has been driven for 3 seconds copyir.com 1 copyir.com The Shutter Home Position Sensor (PI113) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Stack Ejection Motor, and between the Finisher Controller PCB and Shutter Clutch is faulty copyir.com 3 copyir.com The shutter mechanism is faulty copyir.com 4 copyir.com The Stack Ejection Motor (M102), Shutter Clutch (CL101), ang Stack Ejection Lower Roller Clutch (CL102) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E584-8001 Shutter home position error (Finisher-E1)
The stapler does not leave the shutter home position when the Stack Ejection Motor has been driven for 3 seconds copyir.com 1 copyir.com The Shutter Home Position Sensor (PI113) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Stack Ejection Motor, and between the Finisher Controller PCB and Shutter Clutch is faulty copyir.com 3 copyir.com The shutter mechanism is faulty copyir.com 4 copyir.com The Stack Ejection Motor (M102), Shutter Clutch (CL101), ang Stack Ejection Lower Roller Clutch (CL102) is faulty copyir.com 5 copyir.com The Finisher Controller PCB is faulty copyir.com
E590-8001 Punch home position error (External 2 Hole Puncher)
The Puncher does not detect the Punch Home Position Sensor when the Puncher Motor has been driven for 200 msec copyir.com 1 copyir.com The Punch Home Position Sensor (PI63) and Punch Motor Clock Sensor (PI62) is faulty copyir.com 2 copyir.com The wiring between the Punch Controller PCB and Sensor is faulty copyir.com 3 copyir.com The punch mechanism is faulty copyir.com 4 copyir.com The punch motor (M61) is faulty copyir.com 5 copyir.com The Punch Controller PCB is faulty copyir.com 6 copyir.com The Finisher Controller PCB is faulty copyir.com
E590-8002 Punch home position error (External 2 Hole Puncher)
After the Motor has been stopped at time of Punch Motor initialization, the Puncher does not detect Punch Home Position Sensor copyir.com 1 copyir.com The Punch Home Position Sensor (PI63) and Punch Motor Clock Sensor (PI62) is faulty copyir.com 2 copyir.com The wiring between the Punch Controller PCB and Sensor is faulty copyir.com 3 copyir.com The punch mechanism is faulty copyir.com 4 copyir.com The punch motor (M61) is faulty copyir.com 5 copyir.com The Punch Controller PCB is faulty copyir.com 6 copyir.com The Finisher Controller PCB is faulty copyir.com
E591-8001 Scrap full detection error (External 2 Hole Puncher)
The voltage of the light received is 3 copyir.com0 V or less even when the light emitting duty of the Scrap Full Detector Sensor has been increased to 66% or more copyir.com 1 copyir.com The wiring between the Scrap Full Detector PCB and Punch Controller PCB is faulty copyir.com 2 copyir.com The Scrap Full Detector PCB is faulty copyir.com 3 copyir.com The Punch Controller PCB is faulty copyir.com 4 copyir.com The Finisher Controller PCB is faulty copyir.com
E591-8002 Scrap full detection error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com0 V or more even when the light emitting duty of the Scrap Full Detector Sensor has been decreased to 0% copyir.com 1 copyir.com The Scrap Full Detector PCB is faulty copyir.com 2 copyir.com The Punch Controller PCB is faulty copyir.com 3 copyir.com The Finisher Controller PCB is faulty copyir.com
E592-8001 Trailing Edge Sensor error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com5 V or less even when the light emitting duty of the Trailing Edge Sensor (LED5, PTR5) has been increased to 66% or more copyir.com 1 copyir.com The wiring between the LED PCB/Photosensor PCB and Punch Controller PCB is faulty copyir.com 2 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 3 copyir.com The Punch Controller PCB is faulty copyir.com 4 copyir.com The Finisher Controller PCB is faulty copyir.com
E592-8002 Trailing Edge Sensor error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com0 V or more even when the light emitting duty of the Trailing Edge Sensor has been decreased to 0% copyir.com 1 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 2 copyir.com The Punch Controller PCB is faulty copyir.com 3 copyir.com The Finisher Controller PCB is faulty copyir.com
E592-8003 Horizontal Registration Sensor 1 error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com5 V or less even when the light emitting duty of the Horizontal Registration Sensor 1 (LED1, PTR1) has been increased to 66% or more copyir.com 1 copyir.com The wiring between the LED PCB/Photosensor PCB and Punch Controller PCB is faulty copyir.com 2 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 3 copyir.com The Punch Controller PCB is faulty copyir.com 4 copyir.com The Finisher Controller PCB is faulty copyir.com
E592-8004 Horizontal Registration Sensor 1 error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com0 V or more even when the light emitting duty of the Horizontal Registration Sensor 1 (LED1, PTR1) has been decreased to 0% copyir.com 1 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 2 copyir.com The Punch Controller PCB is faulty copyir.com 3 copyir.com The Finisher Controller PCB is faulty copyir.com
E592-8005 Horizontal Registration Sensor 2 error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com5 V or less even when the light emitting duty of the Horizontal Registration Sensor 2 (LED2, PTR2) has been increased to 66% or more copyir.com 1 copyir.com The wiring between the LED PCB/Photosensor PCB and Punch Controller PCB is faulty copyir.com 2 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 3 copyir.com The Punch Controller PCB is faulty copyir.com 4 copyir.com The Finisher Controller PCB is faulty copyir.com
E592-8006 Horizontal Registration Sensor 2 error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com0 V or more even when the light emitting duty of the Horizontal Registration Sensor 2 (LED2, PTR2) has been decreased to 0% copyir.com 1 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 2 copyir.com The Punch Controller PCB is faulty copyir.com 3 copyir.com The Finisher Controller PCB is faulty copyir.com
E592-8007 Horizontal Registration Sensor 3 error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com5 V or less even when the light emitting duty of the Horizontal Registration Sensor 3 (LED3, PTR3) has been increased to 66% or more copyir.com 1 copyir.com The wiring between the LED PCB/Photosensor PCB and Punch Controller PCB is faulty copyir.com 2 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 3 copyir.com The Punch Controller PCB is faulty copyir.com 4 copyir.com The Finisher Controller PCB is faulty
E592-8008 Horizontal Registration Sensor 3 error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com0 V or more even when the light emitting duty of the Horizontal Registration Sensor 3 (LED3, PTR3) has been decreased to 0% copyir.com 1 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 2 copyir.com The Punch Controller PCB is faulty copyir.com 3 copyir.com The Finisher Controller PCB is faulty copyir.com
E592-8009 Horizontal Registration Sensor 4 error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com5 V or less even when the light emitting duty of the Horizontal Registration Sensor 4 (LED4, PTR4) has been increased to 66% or more copyir.com 1 copyir.com The wiring between the LED PCB/Photosensor PCB and Punch Controller PCB is faulty copyir.com 2 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 3 copyir.com The Punch Controller PCB is faulty copyir.com 4 copyir.com The Finisher Controller PCB is faulty copyir.com
E592-800A Horizontal Registration Sensor 4 error (External 2 Hole Puncher)
The voltage of the light received is 2 copyir.com0 V or more even when the light emitting duty of the Horizontal Registration Sensor 4 (LED4, PTR4) has been decreased to 0% copyir.com 1 copyir.com The LED PCB and Photosensor PCB is faulty copyir.com 2 copyir.com The Punch Controller PCB is faulty copyir.com 3 copyir.com The Finisher Controller PCB is faulty copyir.com
E593-8001 Horizontal registration home position error (External 2 Hole Puncher)
At time of Horizontal Registration Motor initialization, the punch slide unit does not leave the Horizontal Home Position Sensor even when it has been driven for 9 mm copyir.com 1 copyir.com The Horizontal Registration Home Position Sensor (PI61) is faulty copyir.com 2 copyir.com The wiring between the Punch Controller PCB and Sensor is faulty copyir.com 3 copyir.com The horizontal registration mechanism is faulty copyir.com 4 copyir.com The Horizontal Registration Motor (M62) is faulty copyir.com 5 copyir.com The Punch Controller PCB is faulty copyir.com 6 copyir.com The Finisher Controller PCB is faulty copyir.com
E593-8002 Horizontal registration home position error (External 2 Hole Puncher)
At time of Horizontal Registration Motor initialization, the punch slide unit does not return to the Horizontal Registration Home Position Sensor even when the unit has been driven for 37 mm copyir.com 1 copyir.com The Horizontal Registration Home Position Sensor (PI61) is faulty copyir.com 2 copyir.com The wiring between the Punch Controller PCB and Sensor is faulty copyir.com 3 copyir.com The horizontal registration mechanism is faulty copyir.com 4 copyir.com The Horizontal Registration Motor (M62) is faulty copyir.com 5 copyir.com The Punch Controller PCB is faulty copyir.com 6 copyir.com The Finisher Controller PCB is faulty copyir.com
E5E1-0001 Tray Lift Motor of Paper Folding Unit failed to go through HP (Document Insertion Unit-L1)
The Paper Feed Sensor (S3) did not turned ON when the Inserter paper feed tray moved up copyir.com 1 copyir.com Connector of the Tray Lift Motor (M2) is disconnected 2 copyir.com Tray Lift Motor (M2) is faulty 3 copyir.com Connector of the Paper Feed Sensor (S3) is disconnected 4 copyir.com Paper Feed Sensor is faulty
E5E1-0002 Tray Lift Motor of Paper Folding Unit failed to return to HP (Document Insertion Unit-L1)
During initialization or lowering of the Inserter paper feed tray, the Tray Lower Limit Sensor (S5) has not turned ON within the specified time copyir.com 1 copyir.com Connector of the Tray Lift Motor (M2) is disconnected 2 copyir.com Tray Lift Motor (M2) is faulty 3 copyir.com Connector of the Tray Lower Limit Sensor (S5) is disconnected 4 copyir.com Tray Lower Limit Sensor (S5) is faulty
E5E1-8001 Tray Lift Motor of Paper Folding Unit failed to go through HP (Document Insertion/Folding Unit-H1)
The Paper Feed Sensor (S3) did not turned ON when the Inserter paper feed tray moved up copyir.com 1 copyir.com Connector of the Tray Lift Motor (M2) is disconnected 2 copyir.com Tray Lift Motor (M2) is faulty 3 copyir.com Connector of the Paper Feed Sensor (S3) is disconnected 4 copyir.com Paper Feed Sensor (S3) is faulty
E5E1-8002 Tray Lift Motor of Paper Folding Unit failed to return to HP (Document Insertion/Folding Unit-H1)
During initialization or lowering of the Inserter paper feed tray, the Tray Lower Limit Sensor (S5) has not turned ON within the specified time copyir.com 1 copyir.com Connector of the Tray Lift Motor (M2) is disconnected 2 copyir.com Tray Lift Motor (M2) is faulty 3 copyir.com Connector of the Tray Lower Limit Sensor (S5) is disconnected 4 copyir.com Tray Lower Limit Sensor (S5) is faulty
E5F0-8001 Paper positioning plate home position error (Finisher-E1)
The paper positioning plate home positio Sensor does not turn ON when the Paper Positioning Plate Motor has been driven for 1500 pulses copyir.com 1 copyir.com The Paper Positioning Plate Home Position Sensor (PI7) is faulty copyir.com 2 copyir.com The positioning plate drive mechanism is faulty copyir.com 3 copyir.com The Paper Positioning Plate Motor (M4) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F0-8002 Paper positioning plate home position error (Finisher-E1) 1 copyir.com The Paper Positioning Plate Home Position Sensor (PI7) is faulty copyir.com 2 copyir.com The wiring between the Finisher Controller PCB and Stack Ejection Motor, and between the Finisher Controller PCB and Shutter Clutch is faulty copyir.com 3 copyir.com The positioning plate drive mechanism is faulty copyir.com 4 copyir.com The Paper Positioning Plate Motor (M4) is faulty copyir.com 5 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F1-8001 Paper Ffolding Motor lock error (Finisher-E1)
The feed speed of the paper fold roller reaches 5 mm/sec or less copyir.com 1 copyir.com The Paper Folding Motor Clock Sensor (PI4) and Paper Ffolding Home Position Sensor (PI21) is faulty copyir.com 2 copyir.com The paper folding roller drive mechanism is faulty copyir.com 3 copyir.com The Paper Folding Motor (M2) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F1-8002 Paper positioning plate home position error (Finisher-E1)
The status of the Paper Fold Home Position Sensor does not change when the paper fold Motor has been driven for 3 seconds copyir.com 1 copyir.com The Paper Folding Motor Clock Sensor (PI4) and Paper Ffolding Home Position Sensor (PI21) is faulty copyir.com 2 copyir.com The paper folding roller drive mechanism is faulty copyir.com 3 copyir.com The Paper Folding Motor (M2) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F2-8001 Guide home position error (Finisher-E1)
The Guide Home Position Sensor does not turn ON when the Guide Motor has been driven for 700 pulses copyir.com 1 copyir.com The Guide Home Position Sensor (PI13) is faulty copyir.com 2 copyir.com The guide plate drive mechanism is faulty copyir.com 3 copyir.com The Guide Motor (M3) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F2-8002 Guide home position error (Finisher-E1)
The Guide Home Position Sensor does not turn OFF when the Guide Motor has been driven for 50 pulses copyir.com 1 copyir.com The Guide Home Position Sensor (PI13) is faulty copyir.com 2 copyir.com The guide plate drive mechanism is faulty copyir.com 3 copyir.com The Guide Motor (M3) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F3-8001 Aligning plate home position error (Finisher-E1)
The Aligning Plate Home Position Sensor does not turn ON when the Aligning Motor has been driven for 500 pulses copyir.com 1 copyir.com The Aligning Plate Home Position Sensor (PI5) is faulty copyir.com 2 copyir.com The aligning plate drive mechanism is faulty copyir.com 3 copyir.com The Aligning Motor (M5) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F3-8002 Aligning plate home position error (Finisher-E1)
The Aligning Plate Home Position Sensor does not turn OFF when the Aligning Motor has been driven for 50 pulses copyir.com 1 copyir.com The Aligning Plate Home Position Sensor (PI5) is faulty copyir.com 2 copyir.com The aligning plate drive mechanism is faulty copyir.com 3 copyir.com The Aligning Motor (M5) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F4-8001 Stitcher (rear) home position error (Finisher-E1)
The Stitcher Home Position Sensor does not turn ON when the Stitch Motor (rear) has been driven backward for 0 copyir.com5 sec copyir.com 1 copyir.com The Stitcher Home Position Sensor (rear) (SW5) is faulty copyir.com 2 copyir.com The Stitcher (rear) is faulty copyir.com 3 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F4-8002 Stitcher (rear) home position error (Finisher-E1)
The stitching home position Sensor does not turn OFF when the Stitch Motor (rear) has been driven forward for 0 copyir.com5 sec copyir.com 1 copyir.com The Stitcher Home Position Sensor (rear) (SW5) is faulty copyir.com 2 copyir.com The Stitcher (rear) is faulty copyir.com 3 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F5-8001 Stitcher (front) home position error (Finisher-E1)
The Stitcher Home Position Sensor does not turn ON when the Stitch Motor (front) has been driven forward for 0 copyir.com5 sec copyir.com 1 copyir.com The Stitcher Home Position Sensor (front) (SW7) is faulty copyir.com 2 copyir.com The Stitcher (front) is faulty copyir.com 3 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F5-8002 Stitcher (front) home position error (Finisher-E1)
The Stitcher Home Position Sensor does not turn OFF when the Stitch Motor (front) has been driven backward for 0 copyir.com5 sec copyir.com 1 copyir.com The Stitcher Home Position Sensor (front) (SW7) is faulty copyir.com 2 copyir.com The Stitcher (front) is faulty copyir.com 3 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F6-8001 Paper pushing plate home position error (Finisher-E1)
The Paper Pushing Plate Home Position Sensor does not turn ON when the Paper Pushing Plate Motor has been driven for 0 copyir.com5 sec copyir.com 1 copyir.com The Paper Pushing Plate Home Position Sensor (PI14), Paper Pushing Plate Top Position Sensor (PI15), and Paper Pushing Plate Motor Clock Sensor (PI1) is faulty copyir.com 2 copyir.com The paper pushing plate drive mechanism is faulty copyir.com 3 copyir.com The Paper Pushing Plate Motor (M8) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F6-8002 Paper pushing plate home position error (Finisher-E1)
The Paper Pushing Plate Home Position Sensor does not turn OFF when the Paper Pushing Plate Motor has been driven for 150 msec copyir.com 1 copyir.com The Paper Pushing Plate Home Position Sensor (PI14), Paper Pushing Plate Top Position Sensor (PI15), and Paper Pushing Plate Motor Clock Sensor (PI1) is faulty copyir.com 2 copyir.com The paper pushing plate drive mechanism is faulty copyir.com 3 copyir.com The Paper Pushing Plate Motor (M8) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F6-8003 Paper Pushing Plate Motor clock error (Finisher-E1)
The number of pulses detected by the Paper Pushing Plate Motor Clock Sensor is 6 pulses or less copyir.com 1 copyir.com The Paper Pushing Plate Home Position Sensor (PI14), Paper Pushing Plate Top Position Sensor (PI15), and Paper Pushing Plate Motor Clock Sensor (PI1) is faulty copyir.com 2 copyir.com The paper pushing plate drive mechanism is faulty copyir.com 3 copyir.com The Paper Pushing Plate Motor (M8) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F6-8004 Pushing position error (Finisher-E1)
The Paper Pushing Plate Leading Edge Position Sensor does not turn ON when the Paper Pushing Plate Motor has been driven for 0 copyir.com1 sec copyir.com 1 copyir.com The Paper Pushing Plate Home Position Sensor (PI14), Paper Pushing Plate Top Position Sensor (PI15), and Paper Pushing Plate Motor Clock Sensor (PI1) is faulty copyir.com 2 copyir.com The paper pushing plate drive mechanism is faulty copyir.com 3 copyir.com The Paper Pushing Plate Motor (M8) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E5F6-8005 Pushing position error (Finisher-E1)
The Paper Pushing Plate Leading Edge Position Sensor does not turn OFF when the Paper Pushing Plate Motor has been driven for 0 copyir.com5 sec copyir.com 1 copyir.com The Paper Pushing Plate Home Position Sensor (PI14), Paper Pushing Plate Top Position Sensor (PI15), and Paper Pushing Plate Motor Clock Sensor (PI1) is faulty copyir.com 2 copyir.com The paper pushing plate drive mechanism is faulty copyir.com 3 copyir.com The Paper Pushing Plate Motor (M8) is faulty copyir.com 4 copyir.com The Saddle Stitcher Controller PCB is faulty copyir.com
E602 Hard disk error See Service manual
E604-1024 Insufficient memory
Insufficient memory (require 1024 MB) copyir.com DDR2-SDRAM
E609-0008 Hard disk error
Temperature of the HDD does not rise to the specified temperature within the specified period of time at the time of startup copyir.com HDD copyir.com
E609-0009 Hard disk error
At the time of recovery from sleep, it does not reach to the specified temperature copyir.com HDD copyir.com
E610-0001 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
The Encryption Board does not exist copyir.com Check the hardware configuration copyir.com
E610-0002 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Not meeting the memory configuration to execute encryption operation copyir.com Check the hardware configuration copyir.com
E610-0101 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Failed to initialize the memory of key storage area copyir.com Turn OFF and then ON the power copyir.com
E610-0102 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Failed to initialize the encryption processing part copyir.com Turn OFF and then ON the power copyir.com
E610-0201 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Error in the encryption processing part copyir.com Turn OFF and then ON the power copyir.com
E610-0202 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Error in the encryption processing part copyir.com Turn OFF and then ON the power copyir.com
E610-0301 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Failed to create the encryption key copyir.com Turn OFF and then ON the power copyir.com
E610-0302 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error) Turn OFF and then ON the power copyir.com Due to this error, HDD content is initialized copyir.com
E610-0303 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Failure of the encryption key is detected copyir.com Turn OFF and then ON the power copyir.com Due to this error, HDD content is initialized copyir.com
E610-0401 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Error is detected during encryption copyir.com Turn OFF and then ON the power copyir.com
E610-0402 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Error is detected during decryption copyir.com Turn OFF and then ON the power copyir.com
E610-0501 Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error)
Error in document management information on /FSTDEV copyir.com Turn OFF and then ON the power copyir.com
E611-0000 Rebooting due to SRAM corruption when executing a transmission job that secures disconnection of the power
In the case that reboot is repeated at recovery from power down because SRAM information is corrupted and the job information saved on SRAM cannot be read, the phenomenon that the communication is repeated occurs copyir.com Clear SRAM to erase the job that secures disconnection of the power copyir.com
E674 FAX error
E677 Print server error
E710-0001 Printer IPC error
Error is detected by IPC communication IC of the printer engine at power ON copyir.com Disconnection of cable copyir.com
E711-0001 IPC communication error
Occurrence of error was set for 4 times or more for 1 copyir.com5 seconds to the error register of the IPC Chip copyir.com Check the Cable copyir.com
E711-0001 IPC communication error (retransmission request reception error)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection copyir.com Check the connection between DCON side (J462) and Finisher Lattice side (J9043) Finisher Cable 2 copyir.com Replace the DC Controller PCB copyir.com
E711-0002 IPC communication error (reception timeout)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection copyir.com Check the connection between DCON side (J462) and Finisher Lattice side (J9043) Finisher Cable 2 copyir.com Replace the DC Controller PCB
E711-0004 IPC communication error (checksum error)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection copyir.com Check the connection between DCON side (J462) and Finisher Lattice side (J9043) Finisher Cable 2 copyir.com Replace the DC Controller PCB copyir.com
E711-0020 IPC communication error (recovery error)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection copyir.com Check the connection between DCON side (J462) and Finisher Lattice side (J9043) Finisher Cable 2 copyir.com Replace the DC Controller PCB copyir.com
E711-0040 IPC communication error (serial error)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection copyir.com Check the connection between DCON side (J462) and Finisher Lattice side (J9043) Finisher Cable 2 copyir.com Replace the DC Controller PCB copyir.com
E713-0001 Finisher IPC communication error (retransmission request reception error)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection of the Finisher copyir.com DC Controller side: J462, Finisher Lattice side: J9043 2 copyir.com Replace the Finisher Controller PCB copyir.com
E713-0002 Finisher IPC communication error (reception timeout)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection of the Finisher copyir.com DC Controller side: J462, Finisher Lattice side: J9043 2 copyir.com Replace the Finisher Controller PCB copyir.com
E713-0004 Finisher IPC communication error (checksum error)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection of the Finisher copyir.com DC Controller side: J462, Finisher Lattice side: J9043 2 copyir.com Replace the Finisher Controller PCB copyir.com
E713-0020 Finisher IPC communication error (recovery error)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection of the Finisher copyir.com DC Controller side: J462, Finisher Lattice side: J9043 2 copyir.com Replace the Finisher Controller PCB copyir.com
E713-0040 Finisher IPC communication error (serial error)
Communication between the host machine and the Finisher was lost copyir.com 1 copyir.com Check the cable connection of the Finisher copyir.com DC Controller side: J462, Finisher Lattice side: J9043 2 copyir.com Replace the Finisher Controller PCB copyir.com
E717-0001 Communication error with the NE Controller
Error when the NE Controller is started copyir.com The NE Controller which was connected before turning OFF the power is not connected at power-on copyir.com Check the cable, and then go through the following to clear the error: Service Mode > COPIER > FUNCTION > CLEAR > ERR copyir.com
E717-0002 Communication error with the NE Controller
IPC error at NE Controller operation copyir.com Open circuit of IPC, unable to recover the IPC communication copyir.com Check the cable, and then go through the following to clear the error: Service Mode > COPIER > FUNCTION > CLEAR > ERR copyir.com
E719-0001 Error in coin manager
Error when the coin manager is started copyir.com The coin manager which was connected before turning OFF the power is not connected at power-on copyir.com Check the cable, and then go through the following to clear the error: Service Mode > COPIER > FUNCTION > CLEAR > ERR copyir.com
E719-0002 Error in coin manager
IPC error at coin manager operation copyir.com Open circuit of IPC, unable to recover the IPC communication copyir.com When open circuit of the pickup/delivery signal cable is detected copyir.com Invalid connection is detected copyir.com Check the cable, and then go through the following to clear the error: Service Mode > COPIER > FUNCTION > CLEAR > ERR copyir.com
E719-0003 Error in coin manager
Communication error with the coin manager occurs during unit price acquisition at startup copyir.com Check the cable, and then go through the following to clear the error: Service Mode > COPIER > FUNCTION > CLEAR > ERR copyir.com
E719-0011 Error when the Card Reader is started
The Card Reader which was connected before turning OFF the power is not connected at power-on copyir.com Check the cable, and then go through the following to clear the error: Service Mode > COPIER > FUNCTION > CLEAR > ERR copyir.com
E719-0012 IPC error at Card Reader operation
Open circuit of IPC, unable to recover the IPC communication copyir.com Check the cable, and then go through the following to clear the error: Service Mode > COPIER > FUNCTION > CLEAR > ERR copyir.com
E719-0031 Communication error when the Card Reader (serial) is started
Unable to start communication with the Card Reader at startup copyir.com 1 copyir.com Check the cable connection of the Card Reader (connector connection error, open circuit), and then go through the following to clear the error: Service Mode > COPIER > FUNCTION > CLEAR > ERR copyir.com 2 copyir.com After removing the Card Reader, execute the following service mode, and then reinstall the Card Reader copyir.com • COPIER>FUNCTION>CLEAR>CARD • COPIER>FUNCTION>CLEAR>ERR
E719-0032 Communication error after the Card Reader (serial) is started
Although communication with the Card Reader was possible at startup, it became unavailable in the middle of it copyir.com Check the cable connection of the Card Reader (connector connection error, open circuit), and then go through the following to clear the error: Service Mode > COPIER > FUNCTION > CLEAR > ERR copyir.com
E720-0001 Different model error
Not proper Finisher is connected copyir.com Check the configuration of options copyir.com
E720-0002 Different model error
Not proper Option Deck is connected copyir.com Check the configuration of options copyir.com
E730-1001 PDL software error
Initialization error copyir.com 1 copyir.com PDL reset processing copyir.com 2 copyir.com Turn OFF and then ON the power copyir.com
E730-100A PDL software error
Systematic fatal error, such as initialization failure, occurs copyir.com 1 copyir.com PDL reset processing copyir.com 2 copyir.com Turn OFF and then ON the power copyir.com
E730-9004 Third party PDL communication error
Communication error with the print server copyir.com 1 copyir.com Turn OFF and then ON the power copyir.com 2 copyir.com Check the cable connection copyir.com 3 copyir.com Replace the Open I/F PCB, F Link PCB (Main/Sub) copyir.com 4 copyir.com Replace the Main Controller PCB copyir.com
E730-9005 Third party PDL communication error
Error in video cable connection with the print server copyir.com 1 copyir.com Turn OFF and then ON the power copyir.com 2 copyir.com Check the cable connection copyir.com 3 copyir.com Replace the Open I/F PCB, F Link PCB (Main/Sub) copyir.com 4 copyir.com Replace the Main Controller PCB copyir.com
E730-A006 PDL communication error
No reply from PDL copyir.com Due to failure of Subbootable, or no existence, there is no reply from PDL copyir.com 1 copyir.com PDL reset processing copyir.com 2 copyir.com Turn OFF and then ON the power copyir.com 3 copyir.com Check the connection of the Main Controller PCB copyir.com 4 copyir.com Reinstall the firmware copyir.com 5 copyir.com Replace the Main Controller PCB copyir.com
E730-A007 Mismatched PDL version
Version of the host machine control software and version of PDL control software are different copyir.com 1 copyir.com PDL reset processing copyir.com 2 copyir.com Turn OFF and then ON the power copyir.com 3 copyir.com System All Format and installation copyir.com
E730-B013 PDL embedded font error
Font data is corrupted copyir.com 1 copyir.com Turn OFF and then ON the power copyir.com 2 copyir.com Reinstall the system copyir.com 3 copyir.com System All Format and installation copyir.com
E732-0000 Reader communication error
Negotiation failure copyir.com 1 copyir.com Check the connection of the Connector with the Reader copyir.com 2 copyir.com Check the power of the Reader (check if the initialization operation is executed at startup) copyir.com 3 copyir.com Replace the Reader Controller PCB and the Main Controller PCB copyir.com
E732-0001 Reader communication error
Communication error copyir.com 1 copyir.com Check the connection of the Connector with the Reader copyir.com 2 copyir.com Check the power of the Reader (check if the initialization operation is executed at startup) copyir.com 3 copyir.com Replace the Reader Controller PCB and the Main Controller PCB copyir.com
E732-0010 Reader communication error
Unable to detect Vsync from the Reader Controller although 2 minutes have passed after the completion of register setting of the Main Controller copyir.com 1 copyir.com Check the connection of the Connector with the Reader copyir.com 2 copyir.com Check the power of the Reader (check if the initialization operation is executed at startup) copyir.com 3 copyir.com Replace the Reader Controller PCB and the Main Controller PCB copyir.com
E732-8888 Reader type error
When a scanner of another model was detected during communication with the Reader copyir.com Replace the Reader with the correct one copyir.com
E732-9999 Detection of Reader
The Reader is detected for the first time with the printer model copyir.com (On the user screen, only the message”Turn OFF and then ON the power again”, instead of an error code, is displayed copyir.com It is recorded as an error log in Service Mode > DISPLAY > ERR copyir.com)
E733-0000 Printer communication error
Communication error between the Main Controller PCB 2 and the DC Controller PCB copyir.com 1 copyir.com Check the cable connection (connector connection error/ open circuit) copyir.com DC Controller PCB: J441, J442, Main Controller PCB 2: J21, J22 2 copyir.com Replace the DC Controller PCB/Main Controller PCB 2 copyir.com
E733-0001 Printer communication error
Communication error between the Main Controller PCB 2 and the DC Controller PCB copyir.com 1 copyir.com Check the cable connection (connector connection error/ open circuit) copyir.com DC Controller PCB: J441, J442, Main Controller PCB 2: J21, J22 2 copyir.com Replace the DC Controller PCB/Main Controller PCB 2 copyir.com
E733-0002 Printer communication error
Communication error between the Main Controller PCB 2 and the DC Controller PCB copyir.com 1 copyir.com Check the cable connection (connector connection error/ open circuit) copyir.com DC Controller PCB: J441, J442, Main Controller PCB 2: J21, J22 2 copyir.com Replace the DC Controller PCB/Main Controller PCB 2 copyir.com
E733-0010 Printer communication error
Communication error between the Main Controller PCB 2 and the DC Controller PCB copyir.com 1 copyir.com Check the cable connection (connector connection error/ open circuit) copyir.com DC Controller PCB: J441, J442, Main Controller PCB 2: J21, J22 2 copyir.com Replace the DC Controller PCB/Main Controller PCB 2 copyir.com
E740-0002 Network Controller error 1 copyir.com Check the connection of the LAN Connector copyir.com 2 copyir.com Check the connection of the Main Controller PCB 1 copyir.com 3 copyir.com Replacement of the Main Controller PCB 1 copyir.com
E743-0000 DDI communication error
The Reader Controller PCB detected the communication error between the Main Controller PCB and the Reader Controller PCB copyir.com 1 copyir.com Connection error between the Main Controller PCB and the Reader Controller PCB copyir.com 2 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the Main Controller PCB copyir.com
E743-0003 DDI communication error
The Reader Controller PCB detected the communication error between the Main Controller PCB and the Reader Controller PCB copyir.com 1 copyir.com Connection error between the Main Controller PCB and the Reader Controller PCB copyir.com 2 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the Main Controller PCB copyir.com
E743-0004 DDI communication error
The Reader Controller PCB detected the communication error between the Main Controller PCB and the Reader Controller PCB copyir.com 1 copyir.com Connection error between the Main Controller PCB and the Reader Controller PCB copyir.com 2 copyir.com Failure of the Reader Controller PCB (PCB1) copyir.com 3 copyir.com Failure of the Main Controller PCB copyir.com
E744 Error in language file/BootROM Download the correct version of the language file copyir.com
E746-0003 Different Image Analysis PCB model
Different Image Analysis PCB model copyir.com 1 copyir.com Check the connection of the Image Analysis PCB copyir.com 2 copyir.com Replace the Image Analysis PCB copyir.com
E746-0021 Image Analysis PCB self-check error detection
Image Analysis PCB self-check error detection copyir.com 1 copyir.com Check the connection of the Image Analysis PCB copyir.com 2 copyir.com Replace the Image Analysis PCB copyir.com
E746-0022 Invalid Image Analysis PCB version 1 copyir.com Upgrade the Image Analysis PCB software copyir.com 2 copyir.com Replace the Image Analysis PCB copyir.com
E746-0023 No reply from Image Analysis PCB
No reply from Image Analysis PCB copyir.com 1 copyir.com Check the connection of the Image Analysis PCB copyir.com 2 copyir.com Replace the Image Analysis PCB copyir.com
E746-0024 Image Analysis PCB operation error
Image Analysis PCB operation error copyir.com 1 copyir.com Check the connection of the Image Analysis PCB copyir.com 2 copyir.com Replace the Image Analysis PCB copyir.com
E746-0031 Hardware error (TPM) The TPM PCB is not installed, the TPM PCB for other model is installed, or failure of TPM Chip copyir.com
E746-0032 Error which the system recovery is not possible occurs (TPM) Location of security information in HDD/SRAM is unknown copyir.com Execute”Initialize All Data/Settings” copyir.com
E746-0033 Error occurs, but system recovery is possible (TPM) Mismatch of key copyir.com Execute restoration of the TPM key copyir.com
E746-0034 Error occurs, but auto recovery of system is possible (TPM) Mismatch of key occurs copyir.com However, recovery by restart is possible copyir.com Turn OFF and then ON the power copyir.com
E748-2000 Main Controller PCB access error
Main Controller PCB Chip access error copyir.com Replace the Main Controller PCB 1/2 copyir.com
E748-2001 Main Controller PCB access error
Main Controller PCB memory access error copyir.com 1 copyir.com Remove and then reinstall the DDR2-SDRAM(M0/M1/P) copyir.com 2 copyir.com Replace the Main Controller PCB 1/2 copyir.com
E748-2010 Flash board error Contact to the sales companies
E748-2011 Flash board error Contact to the sales companies
E748-2012 Flash board error Contact to the sales companies
E748-2021 Main controller board 2 access errors Main controller board 1/2 removing and inserting, replacement
E748-2023 Main controller board 2 access errors DDR2-SDRAM (M0/M1/P) removing and inserting, replacement
E748-2024 Main controller board 2 access errors Main controller board 1/2 removing and inserting, replacement
E748-4910 Main Controller PCB 2 error Replace the Main Controller PCB 2 copyir.com
E748-9000 System error Contact to the sales companies
E753-0001 Download error
Firmware update error copyir.com Turn OFF and then ON the power copyir.com
E753-0001 Download Error
System Software Update Error Error occurs when updating system software of uninstalled options Check the log to find where the download error has been occurred copyir.com FIN_E1 Staple Finisher-E1/Booklet Finisher-E1 G3CCB Super G3 FAX Board-AF1/Super G3 2nd Line Fax Board-AF1/Super G3 3rd/4th Line Fax Board-AE1 G3CCM Super G3 FAX Board-AF1/Super G3 2nd Line Fax Board-AF1/Super G3 3rd/4th Line Fax Board-AE1 When any of the above system software is displayed, check if the target option has been installed copyir.com When the target option has not been installed: Turn OFF and then ON the main power supply to restore (since there is no system software to be updated copyir.com) copyir.com When the target option has been installed: Check if the accessory is correctly installed and if the target system software to be downloaded is for the installed option copyir.com Then download the appropriate system software again copyir.com
E804-0000 Power Supply Cooling Fan 1/2 error
The Fan stop signal is detected for 5 seconds or longer and retry is failed 4 times in a row although the Power Supply Cooling Fan 1 (FM14)/Power Supply Cooling Fan 2 (FM15) is turned ON copyir.com The error detection signal cable is shared with the Fans, and it is not detected with which Fan the error occurs copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Replace the Power Supply Cooling Fan 1 (FM14)/Power Supply Cooling Fan 2 (FM15) copyir.com
E804-0001 Fixing Power Supply Cooling Fan error
The Fan stop signal is detected for 1 copyir.com5 seconds or longer and retry is failed 4 times in a row although the Fixing Power Supply Cooling Fan (FM7) is turned ON copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Replace the Fixing Power Supply Cooling Fan (FM7) copyir.com
E806-0000 Making Image Exhaust Fan error
The Fan stop signal is detected for 5 seconds or longer and retry is failed 4 times in a row although the Making Image Exhaust Fan (FM3) is turned ON copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Replace the Making Image Exhaust Fan (FM3) copyir.com
E808-0001 Fixing Power Supply error
Detected 145V (100V/120V model)/290V (230V model) or higher inlet voltage at power-on copyir.com 1 copyir.com Check the outlet voltage copyir.com -> Connect to the correct outlet copyir.com 2 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10) copyir.com 3 copyir.com Replace the Fixing Power Supply PCB (PCB10) copyir.com 4 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E808-0002 Fixing Power Supply error
Detected 75 V (100V/120V model)/150 V (230V model) or higher inlet voltage at power-on copyir.com 1 copyir.com Check the outlet voltage copyir.com -> Connect to the correct outlet copyir.com 2 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10) copyir.com 3 copyir.com Replace the Fixing Power Supply PCB (PCB10) copyir.com 4 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E808-0003 Fixing Power Supply error
Inlet current is 1A or lower for 1 second or longer although the maximum voltage is output copyir.com 1 copyir.com Check the clogging of the Fixing Power Supply Cooling Fan (FM7) copyir.com 2 copyir.com Check the clogging of the Louver on right side of the host machine (Multi-purpose Tray side) copyir.com 3 copyir.com Check the connection of the Fixing Power Supply PCB (PCB10) Output Connector copyir.com 4 copyir.com Replace the Fixing Power Supply PCB (PCB10) copyir.com
E808-0004 Fixing Power Supply error
Detected OFF with 12V of the Main Driver PCB (PCB2) output copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E808-0005 12V OFF detection when relay is turned ON
Detected OFF with 12V of the Fixing Power Supply output after IH relay is turned ON copyir.com 1 copyir.com Check the conduction of the Fixing Thermal Switch 1/2 (TP1/2) copyir.com 2 copyir.com Check the drawer between the Fixing Assembly and the host machine copyir.com 3 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10) copyir.com 4 copyir.com Replace the Fixing Power Supply Unit copyir.com 5 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E808-0006 ASIC error Replace the DC Controller PCB (PCB1) copyir.com
E808-0007 Fixing Power Supply error
Inlet voltage and the IH Power Supply ID are not matched copyir.com Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10) copyir.com Replace the Fixing Power Supply PCB with the one for the correct location (voltage) copyir.com
E808-0008 Fixing Power Supply error
Current fluctuation error copyir.com 1 copyir.com Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10) copyir.com 2 copyir.com Check the connection between the Fixing Power Supply PCB (PCB10) and the Heater Unit copyir.com 3 copyir.com Replace the Fixing Roller and Heater Unit copyir.com 4 copyir.com Replace the Fixing Power Supply PCB (PCB10) copyir.com 5 copyir.com Replace the Main Driver PCB (PCB2) copyir.com
E808-0009 Fixing Power Supply error
Unable to clear the error flag at power-on copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E820-0000 Developer Lower Cooling Fan error power-on copyir.com
The Fan stop signal is detected for 5 seconds or longer and retry is failed 4 times in a row although the Developer Lower Cooling Fan (FM30) is turned ON copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Replace the Developer Lower Cooling Fan (FM30) copyir.com
E820-0001 Developer Upper Cooling Fan error
The Fan stop signal is detected for 5 seconds or longer and retry is failed 4 times in a row although the Developer Upper Cooling Fan (FM31) is turned ON copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Replace the Developer Upper Cooling Fan (FM31) copyir.com
E820-0002 Duplex Driver Cooling Fan error
The Fan stop signal is detected for 5 seconds or longer and retry is failed 4 times in a row although the Duplex Driver Cooling Fan (FM41) is turned ON copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Replace the Duplex Driver Cooling Fan (FM41) copyir.com
E824-0000 Primary Charging Air Supply Fan error
The Fan stop signal is detected for 5 seconds or longer and retry is failed 4 times in a row although the Primary Charging Air Supply Fan (FM2) is turned ON copyir.com 1 copyir.com Check the connection of the Connector copyir.com 2 copyir.com Replace the Primary Charging Air Supply Fan (FM2) copyir.com
E840-0001 Fixing Shutter Motor error
The Fixing Shutter HP Sensor (PS53) failed the detection at the Fixing Shutter operation copyir.com 1 copyir.com Check the operation of the Fixing Shutter Gear (overload, etc copyir.com) copyir.com 2 copyir.com Check the operation of the Fixing Shutter Motor (M15) at the initialization operation of the Fixing Shutter copyir.com 3 copyir.com Check the detection of the Fixing Shutter HP Sensor (PS53) (if the Sensor operates normally) copyir.com 4 copyir.com Check the drawer of the Fixing Assembly and the host machine copyir.com 5 copyir.com Replace the Fixing Upper Unit and the Fixing Drawer Harness Unit copyir.com 6 copyir.com Replace the Main Driver PCB (PCB2) (check the fuse (FU11)) copyir.com
E880-0001 Controller Fan error
Error in the Main Controller Cooling Fan (FM4) is detected copyir.com Connector disconnection, failure of Fan copyir.com
E880-0005 Controller Fan error
Connector disconnection, failure of Fan copyir.com Error in the HDD Cooling Fan (FM) is detected copyir.com
E905-0001 POD Deck Air Assist Fan error
[POD Deck Lite] When the Air Assist Swing Motor fails to return to the HP although a specified period of time has passed 1 copyir.com Check connector disconnection/improper connection copyir.com => Disconnect and then connect the connector copyir.com Target connector: Deck Lite Controller J04, J05 BoxDriver J51, J52, J57 2 copyir.com Replace the Swing Motor (M3) and the Air Assist Fan (FM1, FM2, FM3) copyir.com 3 copyir.com Replace the Deck Lite Controller PCB copyir.com 4 copyir.com Replace the BoxDriver PCB copyir.com
E905-0002 POD Deck Air Assist Fan error
[POD Deck Lite] When the Pickup Motor Cooling Fan is not locked 1 copyir.com Check connector disconnection/improper connection copyir.com => Disconnect and then connect the connector copyir.com Target connector: Deck Lite Controller J30 2 copyir.com Replace the Motor Cooling Fan (FM4) copyir.com 3 copyir.com Replace the Deck Lite Controller PCB copyir.com
E905-0003 POD Deck Air Assist Fan error
[POD Deck Lite] When the Pickup Motor Cooling Fan is not unlocked 1 copyir.com Check connector disconnection/improper connection copyir.com => Disconnect and then connect the connector copyir.com Target connector: Deck Lite Controller J30 2 copyir.com Replace the Motor Cooling Fan (FM4) copyir.com 3 copyir.com Replace the Deck Lite Controller PCB copyir.com
E906-0001 POD Deck Air Heater error[
POD Deck Lite] Air Heater high temperature error When 120 deg C or higher temperature is detected for 1 second consecutively 1 copyir.com Check connector disconnection/improper connection copyir.com – > Disconnect and then connect the connector copyir.com Target connector: Deck Lite Controller J03, J05 BoxDriver J52, J54, J58, J59 2 copyir.com Replace the Air Heater copyir.com 3 copyir.com Replace the Deck Lite Controller PCB
E906-0002 POD Deck Air Heater errorr high copyir.com
[POD Deck Lite] Air Heater low temperature error When the heater does not become Ready although a specified period of time has passed copyir.com 1 copyir.com Check connector disconnection/improper connection copyir.com – > Disconnect and then connect the connector copyir.com Target connector: Deck Lite Controller J03, J05 BoxDriver J52, J54, J58, J59 2 copyir.com Replace the Air Heater copyir.com 3 copyir.com Replace the Deck Lite Controller PCB copyir.com
E996-xxxx Timeout error
The DC Controller is not stopped copyir.com The Detailed Code varies according to the state transition of the software copyir.com Turn OFF and then ON the main power copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.