لمینت MKP
1402-06-04
Menu
E000-0001 The temperature of the fixing assembly is abnormally high copyir.com
While startup control is under way, the reading of the main thermistor is less than 30 deg C continuously for 200 msec or more 1 sec after the start of power supply copyir.com While startup control is under way, the reading of the main thermistor is less than 70 deg C continuously for 200 msec or more 2 sec after the start of power supply copyir.com While startup control is under way, the reading of the main thermistor is less than 120 deg C continuously for 200 msec 6 sec after the start of power supply copyir.com The startup control does not end 30 sec after the start of power supply copyir.com Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com Replace the main thermistor copyir.com Replace the DC controller PCB copyir.com
E001-0000 The temperature of the fixing assembly is abnormally high copyir.com
The reading of the main thermistor is 250 deg C or more continuously for 200 msec copyir.com Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com Replace the main thermistor copyir.com Replace the DC controller PCB copyir.com
E001-0001 The temperature of the fixing assembly is abnormally high copyir.com
The hardware circuit detects overheating of the main or sub thermistor for 200 msec copyir.com Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com Replace the DC controller PCB copyir.com
E001-0002 The temperature of the fixing assembly is abnormally high copyir.com
The reading of the sub thermistor is 295 deg C or more continuously for 200 msec copyir.com Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com Replace the sub thermistor copyir.com Replace the DC controller PCB copyir.com
E002-0000 The rise in temperature of the fixing assembly is faulty
While startup control is under way, the reading of the main thermistor is less than 115 deg C continuously for 400 msec 1 copyir.com3 sec after it has indicated 100 deg C copyir.com While startup control is under way, the reading of the main thermistor is less than 150 deg C continuously for 400 msec 1 copyir.com3 sec after it has indicated 140 deg C copyir.com Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com Replace the main thermistor copyir.com Replace the DC controller PCB copyir.com
E003-0000 The fixing temperature is too low after a standby state copyir.com
While regular temperature control is under way, the reading of the main thermistor is less than 140 deg C continuously for 400 msec or more copyir.com Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com Replace the main thermistor copyir.com Replace the DC controller PCB copyir.com
E007-0000 The rotation of the fixing film is faulty copyir.com
While the fixing motor is rotating, the marker signal is not detected for 6 sec with the reading of the main thermistor indicating 100 deg C or more copyir.com Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com Replace the main thermistor copyir.com Replace the DC controller PCB copyir.com
E010-0001 The rotation of the main motor is faulty copyir.com
Detection is executed every 100 msec after the start of motor rotation; however, the drive detection signal is absent for 2 sec copyir.com Replace the main motor copyir.com Replace the DC controller PCB copyir.com
E010-0002 The rotation of the main motor is faulty copyir.com
During motor rotation, detection is executed every 100 msec; however, the drive signal is absent 5 times in sequence copyir.com Replace the main motor copyir.com Replace the DC controller PCB copyir.com
E014-0001 The rotation of the fixing motor is faulty copyir.com
Detection is executed every 100 msec after the start of motor rotation; however, the drive detection signal is absent for 2 sec Replace the fixing motor copyir.com Replace the DC controller PCB copyir.com
E014-0002 The rotation of the fixing motor is faulty copyir.com
During motor rotation, detection is executed every 100 msec; however, the drive signal is absent 5 times in sequence copyir.com Replace the fixing motor copyir.com Replace the DC controller PCB copyir.com
E019-0000 The waste toner case is full, or the waste toner case full sensor is faulty
When the waste toner case is identified as being full for 2000 prints continuously, an alert is issued; thereafter, the case is identified as being full continuously for 100 prints Replace the waste toner sensor copyir.com Replace the DC controller PCB copyir.com
E020-0000 The path between the sub hopper and the developing assembly is clogged with toner copyir.com
The developing assembly toner sensor detects the absence of toner, while the sub hopper toner sensor detects the presence of toner copyir.com With the developing clutch turned on, the hopper feedscrew motor is rotated for 1 sec intermittently 194 times; still, the developing assembly toner sensor does not detect the presence of toner copyir.com Replace the developing assembly toner sensor copyir.com Replace the sub hopper toner sensor copyir.com Replace the DC control PCB copyir.com
E024-0000 The developing assembly connector is disconnected copyir.com
The connection detection signal is absent continuously for 100 msec copyir.com Replace the developing assembly toner sensor copyir.com Connect the connector copyir.com Replace the DC controller PCB copyir.com
E025-0000 The hopper motor or the bottle motor is faulty copyir.com
The sub hopper toner sensor connection detection signal is absent for 100 msec 10 times in sequence copyir.com Replace the sub hopper toner sensor copyir.com Connect the connector copyir.com Replace the detection PCB copyir.com
E025-0001 The hopper motor or the bottle motor is faulty copyir.com
While the hopper motor is rotating, the motor error lock signal is detected continuously 4 times every 56 msec copyir.com Or, while the bottle motor is rotating, the motor error lock signal is detected 22 times in sequence every 10 msec copyir.com Replace the hopper motor copyir.com Replace the bottle motor copyir.com Replace the DC controller PCB copyir.com
E032-0001 The NE controller counter malfunctions copyir.com
An open circuit is detected for the count pulse signal copyir.com Turn off the main power, and check the cable for an open circuit; then, turn the main power back on copyir.com
E064-0001 The voltage of the power supply is faulty (high-voltage error) copyir.com
The value read from the EEPORM is outside a specific range copyir.com Turn off and then back on the main power copyir.com Replace the EEPROM copyir.com
E064-0002 The voltage of the power supply is faulty (high-voltage error) copyir.com
While output is being generated, the AD value of the primary DC voltage is 230 (DEC) or more for 100 msec 2 times in sequence copyir.com (However, after output, it is not detected for 100 msec copyir.com) Replace the high-voltage power supply copyir.com Replace the DC controller PCB copyir.com
E064-0003 The voltage of the power supply is faulty (high-voltage error) copyir.com
While output is being generated, the AD value of the developing DC voltage is 224 (DEC) or more for 10 msec 2 times in sequence copyir.com (However, after output, it is not detected for 100 msec copyir.com) Replace the high-voltage power supply copyir.com Replace the DC controller PCB copyir.com
E064-0004 The voltage of the power supply is faulty (high-voltage error) copyir.com
While output is being generated, the AD value of the transfer output current is 205 (DEC) or more for 100 msec 2 times in sequence copyir.com (However, after output, it is not detected for 100 msec copyir.com) Replace the high-voltage power supply copyir.com Replace the controller PCB copyir.com
E064-0005 The voltage of the power supply is faulty (high-voltage error) copyir.com
While output is being generated, the AD value of the transfer output voltage is 0 (DEC) for 100 msec 2 times in sequence copyir.com (However, after output, it is not detected for 100 msec copyir.com) Replace the high-voltage power supply copyir.com Replace the DC controller PCB copyir.com
E100-0001 The BD interval is outside a specific range copyir.com
After the machine has become ready for image formation (i copyir.come copyir.com, the scanner motor is ready for operation, and the laser has been turned on), an error has occurred 50 times or more (BD error) copyir.com Replace the laser unit copyir.com Replace the DC controller PCB copyir.com Check the wiring copyir.com
E110-0001 The scanner motor is faulty copyir.com
The scanner motor speed lock signal does not indicate a locked state a specific period of time after the scanner motor has been started copyir.com Replace the laser unit copyir.com Replace the DC controller PCB copyir.com Check the wiring copyir.com
E110-0002 The scanner motor is faulty copyir.com
The speed lock signal indicates a deviation 10 times in sequence at intervals of 10 msec after the signal has indicated a locked state copyir.com Replace the laser unit copyir.com Replace the DC controller PCB copyir.com Check the wiring copyir.com
E110-0003 The scanner motor is faulty copyir.com
With the image clock switched over, the scanner motor speed lock signal does not indicate a locked state 6 copyir.com5 sec after a switchover is made from low to normal speed or 8 sec after a switchover is made from normal to low speed Replace the laser unit copyir.com Replace the DC controller PCB copyir.com Check the wiring copyir.com
E191-0000 There is an error in the communication with the high-voltage power supply
The data transmission/reception does not end normally 500 msec after the most recent transmission/reception of data ended normally copyir.com Replace the high-voltage power supply copyir.com Replace the DC controller PCB copyir.com
E202-0001 There is an error in the detection of the CIS home position copyir.com
The attempt to detect the home position fails when the CIS is moved forward Disconnect and then connect the harness connector copyir.com Replace the following as necessary: scanner home position sensor, scanner motor, reader controller PCB copyir.com
E202-0002 There is an error in the detection of the CIS home position copyir.com
The attempt to detect the home position fails when the CIS is moved back copyir.com Disconnect and then connect the harness connector copyir.com Replace the following as necessary: scanner home position sensor, scanner motor, reader controller PCB copyir.com
E225-0001 The light intensity of the CIS is faulty copyir.com
During shading operation, the intensity is below a specific level copyir.com Disconnect and then connect the flexible cable copyir.com Replace the following as necessary: flexible cable, CIS, reader controller PCB copyir.com
E225-0002 The light intensity of the CIS is faulty copyir.com
During DF stream reading, the sheet-to-sheet light intensity is faulty copyir.com Disconnect and then connect the flexible cable copyir.com Replace the following as necessary: flexible cable, CIS, reader controller PCB copyir.com
E227-0001 The reader unit power supply is faulty copyir.com
At time of power-on, the 24-V port is off copyir.com Disconnect and then connect the power supply harness connector copyir.com Replace the power supply copyir.com
E227-0002 The reader unit power supply is faulty copyir.com
At the start of a job, the 24-V port is off copyir.com Disconnect and then connect the power supply harness connector copyir.com Replace the power supply copyir.com
E227-0003 The reader unit power supply is faulty copyir.com
At the end of a job, the 24-V port is off copyir.com Disconnect and then connect the power supply harness connector copyir.com Replace the power supply copyir.com
E227-0004 The reader unit power supply is faulty copyir.com
When a load is being driven, the 24-V port is off copyir.com Disconnect and then connect the power supply harness copyir.com Replace the power supply copyir.com
E248-0000 The backup memory is faulty copyir.com
[Cause] A check error has occurred on the backup SRAM board copyir.com [Location] bottom ROM [Timing of Detection] once when the boot ROM is started up 1 copyir.com Check the presence/absence of a backup SRAM PCB copyir.com 2 copyir.com Disconnect and then connect the backup SRAM PCB copyir.com 3 copyir.com Replace the backup SRAM PCB with a new one copyir.com
E248-0001 The backup memory is faulty copyir.com
An error has occurred at power-on copyir.com Replace the reader controller PCB copyir.com
E248-0002 The backup memory is faulty copyir.com
An error has occurred during a write operation copyir.com Replace the reader controller PCB copyir.com
E248-0003 The backup memory is faulty copyir.com
An error has occurred during a read operation following a write operation copyir.com Replace the reader controller PCB copyir.com
E261-0000 The zero-cross signal is faulty copyir.com
When the relay is on, the zero-cross signal is not detected for 500 msec or more copyir.com Replace the AC driver PCB copyir.com Replace the DC controller PCB copyir.com
E315-0007 There is an error in image data copyir.com
There is an error in JBIG encoding copyir.com Turn off and then back on the power copyir.com
E315-000d There is an error in image data copyir.com
There is an error in JBIG decoding copyir.com Turn off and then back on the power copyir.com
E400-0001 DF communication error
Check sum error Disconnect and then connect the connector copyir.com Replace the reader controller PCB copyir.com Replace the ADF controller PCB copyir.com
E400-0002 DF communication error
Reception status error Disconnect and then connect the connector copyir.com Replace the reader control PCB copyir.com Replace the ADF control PCB copyir.com
E400-0003 DF communication error
Reception interrupt error Disconnect and then connect the connector copyir.com Replace the reader controlled PCB copyir.com Replace the ADF controller PCB copyir.com
E490-0001 Wrong DF
The installed DF is not of a supported type copyir.com Install an ADF that is compatible with the machine copyir.com
E500-0001 Finisher communication error
Data communication could not be performed normally copyir.com It has been retried three times in vain copyir.com Replace the finisher controller PCB copyir.com Replace the DC controller PCB copyir.com
E503-0001 fault in communicatio n with the finisher (Finisher-Q3/ Q4)
E503-0002 fault in communicatio n between finisher and saddle unit Replace the finisher controller PCB copyir.com Replace the saddle controller PCB copyir.com Check the cable copyir.com
E503-0003 fault in communicatio n betweenf inisher and punch unit Replace the finisher controller PCB copyir.com Replace the punch drive PCB copyir.com Check the cable copyir.com
E505-0001 fault in the backup memory of the finisher (common among all finishers)
fault in the data stored in backup memory Turn off the main power copyir.com Check the wiring of the DC controller PCB and the finisher controller, and check the fuse of the 24-V power supply copyir.com Thereafter, turn the main power back on copyir.com
E505-0002 fault in the backup memory of the finisher (common among all finishers)
fault in the EEPROM data of the punch unit Replace the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E514-0001 fault in stack delivery motor (Finisher-S1)
When the stack retaining spacer is returned to home position, the belt escape home position sensor does not go on within 1 copyir.com5 sec copyir.com Replace the finisher controller PCB copyir.com Replace the stack delivery motor copyir.com Check the stack delivery drive mechanism copyir.com
E514-0001 fault in trailing edge assist motor (Finisher-Q3/ Q4)
The home position sensor does not go off even when the trailing edge assist motor has rotated for a specific period of time copyir.com Replace the finisher control PCB copyir.com Replace the trailing edge assist motor copyir.com
E514-0002 fault in stack delivery motor (Finisher-S1)When the stack retaining spacer is shifted from home position, the belt escape home position sensor does not go off within 1 copyir.com5 sec copyir.com Replace the finisher controller PCB copyir.com Replace the stack delivery motor copyir.com Check the stack delivery drive mechanism copyir.com
E514-0002 fault in trailing edge assist motor (Finisher-Q3/ Q4)
The home position sensor does not go on even after the trailing edge assist motor has rotated for a specific period of time copyir.com Replace the finisher control PCB copyir.com Replace the trailing edge assist motor copyir.com
E519-0001 Gear change motor error (Finisher-Q3/ Q4)
The home position sensor does not go off even when the gear change motor has rotated for a specific period of time copyir.com Replace the finisher controller PCB copyir.com Replace the gear change motor copyir.com Check the gear change mechanism copyir.com
E519-0002 Gear change motor error (Finisher-Q3/ Q4)
The home position sensor does not go on even when the gear change motor has rotated for a specific period of time copyir.com Replace the finisher controller PCB copyir.com Replace the gear change motor copyir.com Check the gear change mechanism copyir.com
E530-0001 Front alignment error (Finisher-Q3/ Q4)
The home position sensor does not go off even when the front alignment motor has been rotated for a specific period of time copyir.com Replace the finisher controller PCB copyir.com Replace the front alignment motor copyir.com Check the front aligning plate drive mechanism copyir.com Check the front alignment home position sensor copyir.com
E530-0002 Front alignment error (Finisher-Q3/ Q4)
The home position sensor does not go on even when the front alignment motor has been rotated for a specific period of time copyir.com Replace the finisher controller PCB copyir.com Replace the front alignment motor copyir.com Check the front aligning plate drive mechanism copyir.com Check the front alignment home position sensor copyir.com
E530-8001 Rear alignment error (Finisher-S1)
The home position sensor does not go on within 2000 msec after the start of operation when the rear aligning plate is shifted to home position copyir.com Replace the finisher controlled PCB copyir.com Replace the rear alignment motor copyir.com Check the rear aligning plate drive mechanism copyir.com Check the rear alignment home position sensor copyir.com
E530-8002 Rear alignment error (Finisher-S1)
The home position sensor does not go off within 1000 msec after the start of operation when the rear aligning plate is shifted from home position copyir.com Replace the finisher controlled PCB copyir.com Replace the rear alignment motor copyir.com Check the rear aligning plate drive mechanism copyir.com Check the rear alignment home position sensor copyir.com
E531-0001 Stapler error (Finisher-Q3/Q4)
The home position sensor does not go off even when the stapler motor has rotated for a specific period of time copyir.com Replace the finisher controller PCB copyir.com Replace the stapler copyir.com Check the harness copyir.com
E531-0002 Stapler error (Finisher-Q3/Q4)
The home position sensor does not go on even when the stapler motor has rotated for a specific period of time copyir.com Replace the finisher controller PCB copyir.com Replace the stapler copyir.com Check the harness copyir.com
E531-8001 Stapler error (Finisher-S1)
At time of staple jam recovery, the home position sensor does not go on with 500 msec after the start of reverse rotation of the stapler motor Replace the finisher controller PCB copyir.com Replace the stapler copyir.com Check the harness copyir.com
E531-8002 Stapler error (Finisher-S1)
The home position sensor does not go off within 500 msec after the stapler motor has been started copyir.com Replace the finisher controller PCB copyir.com Replace the stapler copyir.com Check the harness copyir.com
E532-0001 Stapler shift error (Finisher-Q3/ Q4)
The home position sensor does not go off even after the stapler shift motor has rotated for a specific period of time copyir.com Replace the finisher controller PCB copyir.com Replace the stapler shift motor copyir.com Check the stapler shift home position sensor copyir.com Check the harness copyir.com
E532-0002 Stapler shift error (Finisher-Q3/ Q4)
The home position sensor does not go on even when the stapler shift motor has rotated for a specific period of time copyir.com Replace the finisher controller PCB copyir.com Replace the stapler shift motor copyir.com Check the stapler shift home position sensor copyir.com Check the harness copyir.com
E532-8001 Stapler shift error (Finisher-S1)
The stapler slide home position sensor does not go on within 11 sec when the stapler is shifted to home position copyir.com Replace the finisher controller PCB copyir.com Replace the stapler shift motor copyir.com Check the stapler shift home position sensor copyir.com Check the harness copyir.com
E532-8002 Stapler shift error (Finisher-S1)
The stapler slide home position sensor does not go off within 1 copyir.com0 sec when the stapler is shifted from home position copyir.com Replace the finisher controller PCB copyir.com Replace the stapler shift motor copyir.com Check the stapler shift home position sensor copyir.com Check the harness copyir.com
E535-0001 Swing cam error (Finisher-S1)
The home position sensor does not go off within 1000 msec after the start of operation when the swing arm is shifted from home position copyir.com Replace the finisher controller PCB copyir.com Replace the swing cam motor copyir.com Check the swing cam home position sensor copyir.com Check the harness copyir.com
E535-0001 Swing cam error (Finisher-Q3/ Q4)
The home position sensor does not go off even when the swing motor has rotated for a specific period of time copyir.com Replace the finisher controller PCB copyir.com Replace the swing cam motor copyir.com Check the swing cam home position sensor copyir.com Check the harness copyir.com
E535-0002 Swing cam error (Finisher-S1)
The home position sensor does not go off within 1 copyir.com0 sec when the stack delivery roller swing arm is moved from home position copyir.com Replace the finisher controller PCB copyir.com Replace the swing cam motor copyir.com Check the swing cam home position sensor copyir.com Check the harness copyir.com
E535-0002 Swing cam error (Finisher-Q3/ Q4)
The home position sensor does not go on even when the swing motor has rotated for a specific period of time Replace the finisher controller PCB copyir.com Replace the swing cam motor copyir.com Check the swing cam home position sensor copyir.com Check the harness copyir.com
E537-0001 Rear alignment error (Finisher-Q3/ Q4)
The home position sensor does not go on within 2000 msec after the start of operation when the read aligning plate is moved to home position copyir.com Replace the finisher controller PCB copyir.com Replace the rear alignment motor copyir.com Check the rear aligning plate drive mechanism copyir.com Check the rear alignment home position sensor copyir.com
E537-0002 Rear alignment error (Finisher-Q3/ Q4)
The home position sensor does not go off within 1000 msec after the start of operation when the rear aligning plate is moved form home position copyir.com Replace the finisher controller PCB copyir.com Replace the rear alignment motor copyir.com Check the rear aligning plate drive mechanism copyir.com Check the rear alignment home position sensor copyir.com
E537-8001 Front alignment error (Finisher-S1)
The home position sensor does not go on within 2 copyir.com0 sec when the front aligning plate is moved to home position copyir.com Replace the finisher controller PCB copyir.com Replace the front alignment motor copyir.com Check the front aligning plate drive mechanism copyir.com Check the front alignment home position sensor copyir.com
E537-8002 Front alignment error (Finisher-S1)
The home position sensor dos not go off within 1 copyir.com0 sec when the front aligning plate is shifted from home position copyir.com Replace the finisher controller PCB copyir.com Replace the front alignment motor copyir.com Check the front aligning plate drive mechanism copyir.com Check the front alignment home position sensor copyir.com
E540-0002 Upper tray ascent/descent motor error (Finisher -Q3/ Q4)
Upper tray ascent/descent motor clock error Replace the No copyir.com 1 tray shift motor copyir.com Replace the finisher controller PCB copyir.com Check the tray ascent/descent mechanism copyir.com
E540-0003 Upper tray ascent/descent motor error (Finisher -Q3/ Q4)
Area error Replace the No copyir.com 1 tray area sensor PCB copyir.com Replace the finisher controller PCB copyir.com
E540-0004 Upper tray ascent/descent motor error (Finisher -Q3/ Q4)
Safety switch activation Check the No copyir.com 1 tray closed detecting switch copyir.com Replace the finisher controller PCB copyir.com
E540-8002 Stack tray motor error (Finisher-S1)
The operation to detect the paper surface of the stack tray does not end within 1 copyir.com0 sec copyir.com Replace the finisher controller PCB copyir.com Replace the tray ascent/ descent motor copyir.com Check the stack tray drive mechanism copyir.com Check the paper surface sensor copyir.com
E540-8003 Stack tray motor error (Finisher-S1)
An abnormal combination of sensor states has been detected copyir.com Replace the finisher controller PCB copyir.com Check the stack tray upper limit sensor copyir.com Check the stack tray lower limit sensor copyir.com Check the stack tray upper paper surface sensor copyir.com Check the stack tray lower paper surface sensor copyir.com
E542-0002 Lower tray ascent/descent motor error (Finisher-Q3/ Q4
Lower tray ascent/descent motor clock error Replace the No copyir.com 2 tray shift motor copyir.com Replace the finisher controller PCB copyir.com Check the tray ascent/descent mechanism copyir.com
E542-0003 Lower tray ascent/descent motor error (Finisher-Q3/ Q4
Area error Replace the No copyir.com 2 tray shift area sensor PCB copyir.com Replace the finisher controller PCB copyir.com
E577-8001 Paddle error (Finisher-S1)
The paddle home position sensor does not go on within 1 copyir.com5 sec when the paddle is shifted to home position copyir.com Check the paddle motor copyir.com Check the paddle home position sensor copyir.com Replace the finisher controller PCB copyir.com
E577-8002 Paddle error (Finisher-S1)
The paddle home position sensor does not go off within 1 copyir.com0 sec when the paddle is moved to home position copyir.com Check the paddle motor copyir.com Check the paddle home position sensor copyir.com Replace the finisher controller PCB copyir.com
E584-0001 Shutter unit error (Finisher-Q3/ Q4)
The shutter open sensor does not go off (i copyir.come copyir.com, the shutter does not close) copyir.com Check the stack edging motor copyir.com Check the open/ close clutch copyir.com Check the shutter home position sensor copyir.com Replace the finisher controller PCB copyir.com
E584-0002 Shutter unit error (Finisher-Q3/ Q4)
The shutter open sensor does not go on (i copyir.come copyir.com, the shutter does not open) copyir.com Check the stack edging motor copyir.com Check the open/ close clutch copyir.com Check the shutter home position sensor copyir.com Replace the finisher controller PCB copyir.com
E590-0001 Punch motor error
The punching home position is not detected even when the puncher motor has been driven for 20 msec copyir.com Check the punch motor copyir.com Check the punch motor clock sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E590-0002 Punch motor error
The punch home position sensor is not defected even after the motor has stopped at time of punch motor initial operation copyir.com Check the punch motor copyir.com Check the punch motor clock sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E591-0001 Punch dust sensor error
Error in light-receiving voltage while light is emitted Check the waste paper case full sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E591-0002 Punch dust sensor error
Error in light-receiving voltage while light is not emitted Check the waste paper case full sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E592-0001 Paper trailing edge sensor/ horizontal sensor error
Error in light-receiving voltage when light is emitted (trailing edge sensor) Check the paper trailing edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E592-0002 paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (trailing edge sensor) Check the paper trailing edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch drive PCB copyir.com Replace the finisher controller PCB copyir.com
E592-0003 Power trailing edge sensor/ registration sensor
Error in light-receiving voltage when light is emitted (horizontal registration sensor 1) Check the paper trailing edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E592-0004 Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 1) Check the paper trailing edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E592-0005 Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is emitted (horizontal registration sensor 2) Check the paper training edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E592-0006 Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 2) Check the paper training edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller copyir.com
E592-0007 Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is emitted (horizontal registration sensor 3) Check the paper trailing edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E592-0008 Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 3) Check the paper trailing edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch drive PCB copyir.com Replace the finisher controller PCB
E592-0009 Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 4) Check the paper trailing edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com
E592-000A Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 4) Check the paper trailing edge sensor copyir.com Check the horizontal registration sensor copyir.com Check the punch drive PCB copyir.com Replace the finisher controller PCB copyir.com
E593-0001 Punch shift motor error
The light-receiving voltage home position sensor does not go off when light is emitted copyir.com Check the horizontal registration motor copyir.com Check the horizontal registration home position sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com Check the punch shift mechanism copyir.com
E593-0002 Punch shift motor error
The light-receiving voltage home position sensor does not go on when light is not emitted copyir.com Check the horizontal registration motor copyir.com Check the horizontal registration home position sensor copyir.com Check the punch driver PCB copyir.com Replace the finisher controller PCB copyir.com Check the punch shift mechanism copyir.com
E5F-0001 Saddle switch error
The inlet cover switch has been identified as being open for 1 sec or more after the start of printing or the start of initial rotation with the following sensors identifying their respective covers as being closed: – inlet cover sensor (PI9S) – nt cover open/closed sensor (PI2S) – delivery cover sensor (PI3S) Or, the front over switch (MS2S) or the delivery cover switch (MS3S) is open copyir.com Inlet cover switch (MS1S)/front cover switch (MS2S)/ delivery cover switch (MS3S) Check the inlet cover switch copyir.com Check the inlet cover sensor copyir.com Check the front cover open/ closed sensor copyir.com Check the delivery cover sensor copyir.com Replace the finisher controller Check the inlet cover switch copyir.com Check the inlet cover sensor copyir.com Check the front cover open/ closed sensor copyir.com Check the delivery cover sensor copyir.com Replace the finisher controller PCB copyir.com
E5F-0002 Saddle switch error
The front cover switch has been identified as being open from the start of printing or the start of initial rotation with the following sensors identifying their respective covers as being closed copyir.com – inlet cover sensor (PI9S) – front cover open/closed sensor (PI2S) – delivery cover sensor (PI3S) – front cover switch (MS2S)/ delivery cover switch (MS3S) Check the front cover switch copyir.com Check the inlet cover sensor copyir.com Check the front cover open/ closed sensor copyir.com Check the delivery cover sensor copyir.com Replace the finisher controller Check the front cover switch copyir.com Check the inlet cover sensor copyir.com Check the front cover open/ closed sensor copyir.com Check the delivery cover sensor copyir.com Replace the finisher controller PCB copyir.com
E5F-0003 Saddle switch error
The delivery cover switch has been identified as being open after the start of printing or the start of initial rotation of the host machine with the following sensors identifying their respective covers as being closed: – inlet cover sensor (PI9S) – front cover open/closed sensor (PI2S) – delivery cover sensor (PI3S) – delivery cover switch (MS3S) Check the delivery cover switch copyir.com Check the inlet cover sensor copyir.com Check the inlet cover sensor copyir.com Check the front cover open/closed sensor copyir.com Check the delivery cover sensor copyir.com Replace the finisher controller PCB copyir.com
E5F0-0001 Saddle paper positioning plate error
The paper positioning plate home position sensor does to go on when the paper positioning motor has been driven for 1 copyir.com33 sec copyir.com Paper positioning plate motor (M4S)/paper positioning plate home position sensor (P17S) Check the paper positioning plate motor copyir.com Check the paper positioning plate home position sensor copyir.com Replace the finisher controller PCB copyir.com Check the paper positioning plate drive mechanism copyir.com
E5F0-0002 Saddle paper positioning plate error
The paper positioning plate home position sensor doest not go off when the paper positioning plate motor has been driven for 1 sec copyir.com Paper positioning plate motor (M4S)/paper positioning plate home position sensor (P17S) Check the paper positioning plate motor copyir.com Check the paper positioning plate home position sensor copyir.com Replace the finisher controller PCB copyir.com Check the paper positioning plate drive mechanism copyir.com
E5F1-0001 Saddle paper folding error
The number of detection pulses of the paper folding motor clock sensor has dropped below a specific value copyir.com Paper folding motor (M2S)/ paper folding motor clock sensor (P14S) Check the paper folding motor copyir.com Check the paper folding motor clock sensor copyir.com Replace the finisher controller PCB copyir.com Check the paper folding plate drive mechanism copyir.com
E5F1-0002 Saddle paper folding error
The state of the paper folding home position sensor doest not change when the paper folding motor has been driven for 3 sec copyir.com Paper folding motor (M2S)/ paper folding motor clock sensor (P14S Check the paper folding motor copyir.com Check the paper folding motor clock sensor copyir.com Replace the finisher controller PCB copyir.com Check the paper folding plate drive mechanism copyir.com
E5F2-0001 Saddle guide error
The guide home position sensor does not go on when the guide motor has been driven for 0 copyir.com455 sec copyir.com Guide motor (M3S)/guide home position sensor (PI13S) Check the guide motor copyir.com Check the guide home position sensor copyir.com Replace the finisher controller PCB copyir.com Check the guide drive mechanism copyir.com
E5F2-0002 Saddle guide error
The guide home position sensor does not go off when the guide motor has been driven for 1 sec copyir.com Guide motor (M3S)/guide home position sensor (PI13S) Check the guide motor copyir.com Check the guide home position sensor copyir.com Replace the finisher controller PCB copyir.com Check the guide drive mechanism copyir.com
E5F3-0001 Saddle alignment error
The aligning plate home position sensor does not go on when the alignment motor has been driven for 0 copyir.com5 sec copyir.com (at time of initialization, 1 copyir.com67 sec copyir.com) Alignment motor (M5S)/ aligning plate home position sensor (PI5S) Check the alignment motor copyir.com Check the alignment home position sensor copyir.com Check the aligning plate drive mechanism copyir.com Replace the finisher controller PCB copyir.com
E5F3-0002 Saddle alignment error
The aligning plate home position sensor does not go off when the alignment motor has been driven for 1 sec copyir.com Alignment motor (M5S)/ aligning plate home position sensor (PI5S) Check the alignment motor copyir.com Check the alignment home position sensor copyir.com Check the aligning plate drive mechanism copyir.com Replace the finisher controller PCB copyir.com
E5F4-0001 Saddle rear stapling error
The stitching home position sensor does not go on when the stitch motor (rear) has been rotated in reverse for 0 copyir.com5 sec or more copyir.com Stitch motor (rear; M6S)/ stitching home position sensor (rear; MS5S) Replace the stitcher (rear) copyir.com Check the harness copyir.com Replace the finisher controller PCB copyir.com
E5F4-0002 Saddle rear stapling error
The stitching home position sensor does not go off when the stitch motor (rear) has been rotated in normal direction for 0 copyir.com5 sec or more copyir.com Stitch motor (rear; MS)/ stitching home position sensor (rear; MS5S) Replace the stitcher (rear) copyir.com Check the harness copyir.com Replace the finisher controller PCB copyir.com
E5F5-0001 Saddle front stapling error
The stitching home position sensor does not go on when the stitch motor (front) has been rotated in reverse for 0 copyir.com5 sec or more copyir.com Stitch motor (front; M7S)/ stitching home position sensor (front; MS7S) Replace the stitcher (front) copyir.com Check the harness copyir.com Replace the finisher controller PCB copyir.com
E5F5-0002 Saddle front stapling error
The stitching home position sensor does not go off when the switch motor (front) has been rotated in normal direction for 0 copyir.com5 sec or more copyir.com Stitch motor (front; M7S)/ stitching home position sensor (front; MS7S) Replace the stitcher (front) copyir.com Check the harness copyir.com Replace the finisher controller PCB copyir.com
E5F6-0001 Saddle butting error
The paper butting plate home position sensor does not go on when the paper butting plate motor has been driven for 0 copyir.com3 sec copyir.com Paper butting plate motor (M8S)/paper butting plate home position sensor (PI14S) Check the paper butting plate motor copyir.com Check the paper butting plate home position sensor copyir.com Replace the finisher controller PCB copyir.com
E5F6-0002 Saddle butting error
The paper butting plate home position sensor does not go off when the paper butting plate motor has been driven for 80 msec or more copyir.com Paper butting plate motor (M8S)/paper butting plate home position sensor (PI14S) Check the paper butting plate motor copyir.com Check the paper butting plate home position sensor copyir.com Replace the finisher controller PCB copyir.com
E5F6-0003 Saddle butting error
The number of detection pulses of the paper butting plate motor has dropped below a specific value copyir.com paper butting plate motor (M8S)/paper butting plate motor clock sensor (PI1S)
Check the paper butting plate motor copyir.com Check the paper butting plate motor clock sensor copyir.com Replace the finisher controller Check the paper butting plate motor copyir.com Check the paper butting plate motor clock sensor copyir.com Replace the finisher controller PCB copyir.com
E5F6-0004 Saddle butting error
The paper butting plate leading edge sensor does not go off when the paper butting plate motor has been driven for 80 msec copyir.com Paper butting plate motor (M8S)/paper butting plate leading edge sensor (PI15S) Check the paper butting plate motor copyir.com Check the paper butting plate leading edge sensor copyir.com Replace the finisher controller PCB copyir.com
E5F6-0005 Saddle butting error
The paper butting plate leading edge sensor does not go on when the paper butting plate motor has been driven for 0 copyir.com3 sec copyir.com Paper butting plate more (M8S)/paper butting plate leading edge sensor (PI15S) Check the paper butting plate motor copyir.com Check the paper butting plate leading edge sensor copyir.com Replace the finisher controller PCB copyir.com
E5F8-0001 Saddle connector error
The connector of the paper butting plate home position sensor has been identified as being disconnected copyir.com Connector of guide home position sensor (PI13S) Connect the connector of the guide home position sensor copyir.com Check the harness copyir.com Replace the finisher controller PCB copyir.com
E5F8-0002 Saddle connector error
The connector of the paper butting plate home position sensor has been identified as being disconnected copyir.com Connector of paper butting plate home position sensor (PI14S) Connect the connector of the paper butting plate home position sensor copyir.com Check the harness copyir.com Replace the finisher controller PCB copyir.com
E5F8-0003 Saddle connector error
The connector of the paper butting plate leading edge sensor has been identified as being disconnected copyir.com Connector of paper butting plate leading edge sensor (PI15S) Connect the connector of the paper butting plate leading edge sensor copyir.com Check the harness copyir.com Replace the finisher controller PCB copyir.com
E602-0001 There is an error on the hard disk copyir.com
[Cause] An HDD detection error has occurred copyir.com The HDD cannot be detected copyir.com The HDD does not become ready copyir.com The HDD returns an error copyir.com [Detection] while boot ROM is in session BARSAC startup, mounting (usrIde) [Timing of Detection] once at startup
E602-0002 There is an error on the hard disk copyir.com
[Cause] There is no startup file copyir.com The program for the main CPU does not exist on the HDD or in BOOTDEV/BOOT, and so on copyir.com [Detection] while boot ROM is in use at time of system file loading (usrIde) [Timing of Detection] once at startup
E602-0003 There is an error on the hard disk copyir.com
[Cause] An HD write abort error has occurred copyir.com The sectors for BOOTDEV on the HD cannot be read copyir.com [Detection] BARSAC (all; at time of bootable startup) [Timing of Detection] once at startup
E602-0006 There is an error on the hard disk copyir.com
[Cause] A subbootable that matches the PDL type does not exit in BOOTDEV/BOOT copyir.com [Detection] during loading of sub boot in oclibroot [Timing of Detection] once at bootable startup
E602-0007 There is an error on the hard disk copyir.com
[Cause] An ICC profile that matches the PDL type does not exist in BOOTDEV/PDL copyir.com [Detection] beginning of oclibroot; judgment based on functions of PDL team that are called in [Timing of Detection] once at bootable startup
E602-01XX There is an error on the hard disk copyir.com
/DOSDEV is faulty
E602-02XX There is an error on the hard disk copyir.com
/FSTDEV is faulty copyir.com
E602-03XX There is an error on the hard disk copyir.com
/DOSDEV2 is faulty copyir.com
E602-04XX There is an error on the hard disk copyir.com
/FSTPDEV is faulty copyir.com
E602-05XX There is an error on the hard disk copyir.com
/DOSDEV3 is faulty copyir.com
E602-06XX There is an error on the hard disk copyir.com
/PDLDEV is faulty copyir.com
E602-07XX There is an error on the hard disk copyir.com
/DOSDEV4 is faulty copyir.com
E602-08XX There is an error on the hard disk copyir.com
/BOOTDEV is faulty copyir.com
E602-09XX There is an error on the hard disk copyir.com
/DOSDEV5 is faulty copyir.com
E602-FFXX There is an error on the hard disk copyir.com
There is an error in a partition that cannot be identified copyir.com
E604-0000 The image memory is faulty or is inadequate copyir.com
The memory size does not match the model copyir.com Increase the memory copyir.com
E609-0008 There is an error on the HDD copyir.com
At startup, the HDD fails to reach a specific temperature level within a specific period of time copyir.com Replace the hard disk copyir.com Replace the DC controller PCB copyir.com
E609-0009 There is an error on the HDD copyir.com
At time of sleep recovery, the temperature fails to reach a specific level copyir.com Replace the hard disk copyir.com Replace the DC controller PCB copyir.com
E610 The HDD coding key is faulty copyir.com
The SRM/PCB is faulty copyir.com The battery has become exhausted, leading to loss of SRAM contents copyir.com Try step 1); if it fails, try step 2) copyir.com 1) Turn off and then back on the power switch to generate the key once again copyir.com 2) If the same error still continues, replace the board on which the SRAM is mounted copyir.com (Keep in mind that doing so will lead to loss of all user data copyir.com)
E674-0001 An error has occurred in communication between the fax control PCB (2-line) and main controller PCB copyir.com
An attempt to set mode for the fax device has failed copyir.com 1 copyir.com Check the connection of the cable between the fax control PCB (2-line) and the main controller PCB copyir.com 2 copyir.com Replace the ROM DIMM of the fax control PCB (2-line) copyir.com 3 copyir.com Replace the fax control PCB (2- line) copyir.com 4 copyir.com Replace the main controller PCB copyir.com
E710-0001 There is an error in the initialization of the IPC copyir.com
The machine fails to become ready 3 sec or less after the IPC chip startup copyir.com Check the cable copyir.com
E710-0002 There is an error in the initialization of the IPC copyir.com
When the main power is turned on, the communication IC (IPC) on the DC controller PCB cannot be initialized copyir.com Check the cable copyir.com
E711-0001 There is an error in the IPC communication copyir.com
The occurrence of an error has been recorded in the error register of the IPC chip 4 times or more within 1 copyir.com5 sec copyir.com Check the cable copyir.com
E711-0002 There is an error in the IPC communication copyir.com
The occurrence of an error has been recorded in the error register of the IPC chip 4 times or more within 2 sec copyir.com Check the cable copyir.com
E713-0000 There is an error in the communication with the finisher copyir.com
The communication with the finisher does not resume within 5 sec after it has been disrupted copyir.com Check the cable copyir.com Replace the DC controller PCB copyir.com Replace the finisher controller PCB copyir.com
E716-0000 There is an error in the communication with the pedestal copyir.com
After the presence of a pedestal has been detected, the communication fails to be normal for 5 sec Check the cable copyir.com Replace the DC controller PCB copyir.com Replace the pedestal drive PCB copyir.com
E717-0001 There is an error in the communication with the NE controller copyir.com
The NE controller is not connected at power on, although it was connected before the power was turned off because of an error copyir.com Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com
E717-0002 There is an error in the communication with the NE controller copyir.com
An IPC error has occurred while the NE controller is in operation copyir.com There is an open circuit for the IPC copyir.com An error has occurred, and the IPC communication remains disabled Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com
E719-0001 There is a coin vendor error copyir.com
The coin vendor is not connected when the power is turned on, although it was connected before the power was turned off because of an error copyir.com Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com
E719-0002 There is a coin vendor error copyir.com
While the coin vendor is in operation, an IPC error has occurred, IPC has developed an open circuit, or an error preventing recovery of IPC communication has occurred copyir.com An open circuit has been detected in the line for the pickup/delivery signal copyir.com An illegal signal has been detected copyir.com Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com
E719-0003 There is a coin vendor error copyir.com
While the unit price is being checked at startup, an error occurs in the communication with the coin vendor copyir.com Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com
E719-0011 There is a coin vendor error copyir.com
An error has occurred at new card reader startup copyir.com The new card reader is not connected when the power is turned off, although it was connected when the power was turned off copyir.com Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com
E719-0012 There is a coin vendor error copyir.com
An IPC error has occurred at new card reader startup copyir.com There is an IPC open circuit copyir.com An error has occurred that prevents recovery of IPC communication copyir.com Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR copyir.com
E730-1001 There is a PDL software error
An initialization error has occurred copyir.com 1 copyir.com Execute PDL resetting copyir.com 2 copyir.com Turn on the power once again copyir.com
E730-100A There is a PDL software error
An error that may be critical to the system (e copyir.comg copyir.com, failed initialization) has occurred copyir.com 1 copyir.com Execute PDL resetting copyir.com 2 copyir.com Turn on the power once again copyir.com
E730-9004 There is a PDL software error
There is an error in the communication (PAI) with an external controller copyir.com 1 copyir.com Turn on the power once main copyir.com 2 copyir.com Check the connection of the open I/F board and the cable copyir.com 3 copyir.com Replace the board for the external controller open I/F copyir.com 4 copyir.com Replace the main board copyir.com
E730-9005 There is a PDL software error
There is a fault in the connector of the vide cable to the external controller 1 copyir.com Turn on the power once main copyir.com 2 copyir.com Check the connection of the open I/F board and the cable copyir.com 3 copyir.com Replace the board for the external controller open I/F copyir.com 4 copyir.com Replace the main board copyir.com
E730-A006 There is a PDL software error
The PDL board does not respond copyir.com A subbootable is faulty or absent 1 copyir.com Execute PDL resetting copyir.com 2 copyir.com Turn on the power once again copyir.com 3 copyir.com Check the connection of the SURF board copyir.com 4 copyir.com Re-install the firmware copyir.com 5 copyir.com Replace the main board copyir.com
E730-A007 There is a PDL software error
There is a mismatch between the control software of the machine and the PDL control software in regard to version copyir.com 1 copyir.com Execute PDL resetting copyir.com 2 copyir.com Turn on the power once again copyir.com 3 copyir.com Execute system formatting (all), and reinstall the system copyir.com
E730-B013 There is a PDL software error
There is corruption in the font data copyir.com 1 copyir.com Turn on the power once again copyir.com 2 copyir.com Re-install the software copyir.com 3 copyir.com Execute system formatting (all), and reinstall the system copyir.com
E732-0001 There is an error in the communication with the scanner
There is a DDI-S communication error copyir.com 1 copyir.com Check the connector used to connect the scanner copyir.com 2 copyir.com Check the power supply of the scanner (to see if initialization takes place at startup) copyir.com 3 copyir.com Replace the reader controller, scanner board, or main board as necessary copyir.com
E733-0000 There is an error in the communication with the printer copyir.com
At startup, communication with the printer fails copyir.com 1 copyir.com Check the connector used to connect to the printer copyir.com 2 copyir.com Check the power supply of the printer (to see if initialization takes place at startup) copyir.com 3 copyir.com Replace the DC controller or the main board copyir.com
E733-0001 There is an error in the communication with the printer copyir.com
There is a DDI-P communication error 1 copyir.com Check the connection with the printer copyir.com 2 copyir.com Check the power supply of the printer (to see if initialization takes place at startup) copyir.com 3 copyir.com Replace the DC controller or the main board copyir.com
E740-0002 There is an error on the Ether board copyir.com
The MAC address is illegal copyir.com Replace the LAN card copyir.com
E743-0000 There is an error in the DDI communication copyir.com
An SCI error has occurred copyir.com The received data is faulty copyir.com A reception timeout condition has occurred copyir.com An SEQ timeout error has occurred copyir.com Disconnect and then connect the flexible cable used to connect the reader unit and the printer unit copyir.com Replace the following as necessary: flexible cable, reader controller PCB, main controller PCB copyir.com
E744-0001 There is an error in the language file/boot ROM copyir.com
The version of the language file on the HDD and that of the bootable do not match copyir.com Download a language file of the correct version copyir.com
E744-0002 There is an error in the language file/boot ROM copyir.com
The size of the language file on the HDD is too large copyir.com Download a language file of the correct version copyir.com
E744-0003 There is an error in the language file/boot ROM copyir.com
There is no language file on the HDD indicated by config copyir.comtxt for a switchover copyir.com Download a language file of the correct version copyir.com
E744-0004 There is an error in the language file/boot ROM copyir.com
An attempt to switchover to a language on the HDD fails Download a language file of the correct version copyir.com
E744-1000 There is an error in the language file/boot ROM copyir.com
The boot ROM that is mounted is of the wrong type copyir.com Replace the boot ROM with one of the model in question copyir.com
E744-2000 There is an error in the language file/boot ROM copyir.com
The engine ID indicated by the software ID is illegal copyir.com Replace it with a software ID of the correct model copyir.com
E745-0001 There is a fault on the TokeRing board copyir.com
An attempt at PCI initialization has failed copyir.com 1 copyir.com Disconnect and then connect the TokeRing board copyir.com 2 copyir.com Replace the TokeRing board copyir.com
E745-0002 There is a fault on the TokeRing board copyir.com
The MAC address is faulty 1 copyir.com Replace the TokenRing board copyir.com
E745-0003 There is a fault on the TokeRing board copyir.com
There is an error in the acquisition/setting of board information copyir.com 1 copyir.com Replace the TokenRing board copyir.com
E745-0004 There is a fault on the TokeRing board copyir.com
There is a connection error 1 copyir.com Check the connection of the cable copyir.com 2 copyir.com Replace the cable copyir.com 3 copyir.com Check the power source of the MAU copyir.com 4 copyir.com Replace the MAU copyir.com 5 copyir.com Replace the TokenRing board copyir.com
E745-0005 There is a fault on the TokeRing board copyir.com
Other Errors
E746-0003 The accessories board is of the wrong type
At startup, a board for a different model has been detected copyir.com Replace the UFR board of the correct type (model) copyir.com
E748-1001 There is a mismatch between controller board and SDRAM size copyir.com
There is a mismatch between the control board and the SDRAM copyir.com Check the correct combination between board and SDRAM copyir.com
E805-0000 There is a fan error copyir.com
While the fan is at rest, the lock signal has been detected for 5 sec copyir.com While the fan is in operation, the lock signal is not detected for 5 sec Replace the fan copyir.com Replace the DC controller PCB copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.