لمینت MKP
1402-06-04
Menu
E000 The fixing assembly fails to warm up normally
• The fixing assembly fails to reach the target temperature 180 sec after the start of warm-up copyir.com Thermistor 1( کپی ایران ) Is the thermistor soiled? YES: Clean the thermistor copyir.com Is the thermistor in even contact with the fixing upper roller? NO: Mount the thermistor correctly copyir.com Turn off the power switch, and remove the fixing assembly copyir.com Measure the resistance between connectors J50B-2 (FSRTH( کپی ایران ) and J50B- 3 (GNDTH( کپی ایران ) on the fixing assembly side copyir.com Is it between 120k and 290k Ohm NO: Check the wiring from J222 on the DC controller PCB to the thermistor; if normal, replace the thermistor copyir.com Main heater 2( کپی ایران ) With the fixing assembly removed, is there electrical continuity between connectors J50-3 (FSRN1( کپی ایران ) and J50-5 (FSRL1( کپی ایران ) on the fixing assembly side? NO: Replace the main heater copyir.com Sub heater 3( کپی ایران ) With the fixing assembly removed, is there electrical continuity between connectors J50-4 (FSRN2( کپی ایران ) and J50-5 (FSRL2( کپی ایران ) on the fixing assembly side? NO: Replace the sub heater copyir.com Thermal switch, DC controller PCB 4( کپی ایران ) Remove the fixing assembly, and detach the wiring cover copyir.com Is there electrical continuity between the terminals of the thermal switch? NO: Replace the thermal switch copyir.com YES: Replace the DC controller PCB
E001 The fixing assembly suffers from abnormally high temperature
• The fixing temperature exceeds about 230°C during standby or during copying operation copyir.com Thermistor 1( کپی ایران ) Turn off the power switch, and remove the fixing assembly copyir.com Then, measure the resistance between connectors J50B-2 (FSRTH( کپی ایران ) and J50B-3 (GNDTH( کپی ایران ) of the fixing assembly side copyir.com Is the resistance 1k Ohm or less? NO: Check the wiring from J222 on the DC controller PCB to the thermistor; if normal, replace the thermistor copyir.com Power supply assembly, DC controller PCB 2( کپی ایران ) Replace the power supply assembly copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the DC controller PCB copyir.com
E003 The fixing assembly suffers from abnormally low temperature copyir.com
• The fixing temperature drops below 120°C after it has reached the target temperature copyir.com Thermistor 1( کپی ایران ) Is the thermistor soiled? YES: Clean the thermistor copyir.com Is the thermistor in even contact with the fixing upper roller? NO: Mount the thermistor correctly copyir.com Turn off the power switch, and remove the fixing assembly copyir.com Measure the resistance between connectors J50B-2 (FSRTH( کپی ایران ) and J50B- 3 (GNDTH( کپی ایران ) on the fixing assembly side copyir.com Is it between 120k and 290k Ohm NO: Check the wiring from J222 on the DC controller PCB to the thermistor; if normal, replace the thermistor copyir.com Main heater 2( کپی ایران ) With the fixing assembly removed, is there electrical continuity between connectors J50-3 (FSRN1( کپی ایران ) and J50-5 (FSRL1( کپی ایران ) on the fixing assembly side? NO: Replace the main heater copyir.com Sub heater 3( کپی ایران ) With the fixing assembly removed, is there electrical continuity between connectors J50-4 (FSRN2( کپی ایران ) and J50-5 (FSRL2( کپی ایران ) on the fixing assembly side? NO: Replace the sub heater copyir.com Thermal switch, DC controller PCB 4( کپی ایران ) Remove the fixing assembly, and detach the wiring cover copyir.com Is there electrical continuity between the terminals of the thermal switch? NO: Replace the thermal switch copyir.com YES: Replace the DC controller PCB
E009 The type of fixing assembly is wrong
• The rated voltage of the machine and the rated voltage of the fixing assembly do not match copyir.com Fixing assembly 1( کپی ایران ) Is the fixing assembly rated at a voltage different from that of the power supply? YES: Replace the fixing assembly so that its voltage matches the fixing assembly copyir.com Power supply assembly, DC controller PCB 2( کپی ایران ) Replace the power supply assembly copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the DC controller PCB copyir.com
E010 The main motor fails to start up normally
• The revolution of the main motor fails to reach a specific revolution copyir.com Connector 1( کپی ایران ) Is connector J12 of the main motor and connector J218 on the DC controller PCB connected correctly? YES: Connect them correctly copyir.com Switch, Door switch of sensor PCB 2( کپی ایران ) Disconnect connectors J205 and J221 from the DC controller PCB copyir.com Is there electrical continuity between J205-3 (+24 V( کپی ایران ) and J221-1 (+24 VB( کپی ایران ) on the harness side when the door switch (SW1401( کپی ایران ) is turned on? NO: Replace the switch/sensor PCB copyir.com Main motor, DC controller PCB 3( کپی ایران ) Can the main motor be rotated using a printer driver checker? NO: Replace the main motor copyir.com
E011 The main motor fails to rotate normally
• The revolution of the main motor deviates from a specific revolution copyir.com Connector 1( کپی ایران ) Is connector J12 of the main motor and connector J218 on the DC controller PCB connected correctly? YES: Connect them correctly copyir.com Switch, Door switch of sensor PCB 2( کپی ایران ) Disconnect connectors J205 and J221 from the DC controller PCB copyir.com Is there electrical continuity between J205-3 (+24 V( کپی ایران ) and J221-1 (+24 VB( کپی ایران ) on the harness side when the door switch (SW1401( کپی ایران ) is turned on? NO: Replace the switch/sensor PCB copyir.com Main motor, DC controller PCB 3( کپی ایران ) Can the main motor be rotated using a printer driver checker? NO: Replace the main motor copyir.com
E040 The holding lifter (multifeeder( کپی ایران ) is faulty
• When the multifeeder is selected, the holding plate position sensor (PS1302( کپی ایران ) does not detect the holding plate despite the holding plate solenoid (SL2( کپی ایران ) activation signal from the DC controller PCB copyir.com Holding plate drive assembly 1( کپی ایران ) Is there any damaged part in the holding plate drive assembly? YES: Replace any damaged part copyir.com Holding plate position sensor 2( کپی ایران ) Check the condition of the sensor using the printer driver checker copyir.com Is the result good? NO: Replace the multifeeder tray PCB copyir.com Holding plate solenoid, DC controller PCB 3( کپی ایران ) Disconnect connector J1302 of the holding plate solenoid, and measure the resistance between connectors J1302-1 and J1302-2 on the harness side copyir.com Is the resistance about 100 Ohm NO: Replace the holding plate solenoid copyir.com YES: Replace the DC controller PCB copyir.com
E043 Paper Deck Feed motor (faulty( کپی ایران )
• The motor of the paper deck does not operate normally copyir.com
E054 The duplex feed roller drive mechanism of the duplex unit is faulty copyir.com
• The duplex driver PCB detects that the horizontal registration guide exceeded its maximum travel distance after the detection of the horizontal registration guide home position has started copyir.com Duplex feed roller 1 home position sensor lever 1( کپی ایران ) Is the duplex feed roller 1 home position sensor lever damaged? YES: Replace the lever copyir.com Duplex feed roller gear 2( کپی ایران ) Is the duplex feed roller gear worn or chipped? YES: Replace the worn/chipped gear copyir.com Duplex driver PCB 3( کپی ایران ) Are connectors J2003, J2004, and J2007 on the duplex driver PCB connected securely? NO: Connect them securely copyir.com Duplex feed roller 1 home position sensor 4( کپی ایران ) Try replacing the duplex feed roller 1 home potion sensor copyir.com Is the problem corrected? YES: End copyir.com Duplex feed clutch 5( کپی ایران ) Disconnect connector J2003 of the duplex feed clutch, and measure the resistance between connectors J2003-1 and J2003-2 on the harness side copyir.com Is it about 140 Ohm Duplex motor, Duplex motor driver PCB 6( کپی ایران ) Try replacing the duplex motor copyir.com Is the problem corrected? NO: Replace the duplex driver PCB copyir.com
E055 The horizontal registration guide drive mechanism of the duplex unit is faulty copyir.com
• The duplex driver PCB detects that the horizontal registration guide exceeded its maximum travel distance after the detection of the horizontal registration guide home position has started copyir.com Horizontal registration guide 1( کپی ایران ) Is the horizontal registration guide mounted correctly? NO: Mount it correctly copyir.com Horizontal registration guide home position sensor lever 2( کپی ایران ) Is the horizontal registration guide home position sensor lever damaged? YES: Replace the lever copyir.com Horizontal registration guide drive gear 3( کپی ایران ) Is the horizontal registration guide drive gear worn/chipped? YES: Replace the worn/chipped gear copyir.com Duplex driver PCB 4( کپی ایران ) Are connectors J2006 and J2005 on the duplex driver PCB connected securely? NO: Connect them securely copyir.com Horizontal registration guide home position sensor 5( کپی ایران ) Try replacing the horizontal registration guide home position copyir.com Is the problem corrected? YES: Replace the sensor copyir.com Horizontal registration motor, Duplex drive motor PCB 6( کپی ایران ) Try replacing the horizontal registration motor copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the duplex driver PCB copyir.com
E100 The BD of the scanner unit is faulty copyir.com
• The scanner motor fails to reach a specific revolution within 10 sec after it has started to rotate copyir.com • The BD PCB detects an error for 2 copyir.com5 sec or more after the scanner motor has started to rotate at a specific speed copyir.com Condensation 1( کپی ایران ) Leave the machine alone for 10 to 20 min copyir.com Is the problem corrected? YES: End copyir.com BD signal line connector 2( کپی ایران ) Are connector J6 on the BD PCB and connector J206 on the DC controller PCB connected securely? NO: Connect them securely copyir.com Laser driver signal line connector 3( کپی ایران ) Are connector J1001 on the laser driver PCB and connector J202 on the DC controller PCB connected securely? NO: Connect the connectors securely copyir.com Laser scanner assembly, DC controller PCB 4( کپی ایران ) Try replacing the laser scanner assembly copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the DC controller PCB copyir.com
E102 The laser is faulty copyir.com
• The intensity of the laser fails to reach a specific level copyir.com Condensation 1( کپی ایران ) Leave the machine alone for 10 to 20 min copyir.com Is the problem corrected? YES: End copyir.com BD signal line connector 2( کپی ایران ) Are connector J6 on the BD PCB and connector J206 on the DC controller PCB connected securely? NO: Connect them securely copyir.com Laser driver signal line connector 3( کپی ایران ) Are connector J1001 on the laser driver PCB and connector J202 on the DC controller PCB connected securely? NO: Connect the connectors securely copyir.com Laser scanner assembly, DC controller PCB 4( کپی ایران ) Try replacing the laser scanner assembly copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the DC controller PCB copyir.com
E110 The laser scanner motor is faulty copyir.com
• The scanner motor fails to reach a specific revolution within 10 sec after it has started to rotate copyir.com • The BD PCB detects an error for 2 copyir.com5 sec or more after the scanner motor has started to rotate at a specific revolution copyir.com Scanner motor drive line 1( کپی ایران ) Are connector J1 on the scanner driver PCB, relay connector J18, and connector J207 on the DC controller PCB connected securely? Scanner motor driver, DC controller PCB 2( کپی ایران ) Can the scanner motor be rotated using a printer driver checker? NO: Replace the laser scanner copyir.com YES: Replace the DC controller PCB copyir.com
E202 The scanner home position cannot be detected copyir.com • The original scanner home position sensor (PS101( کپی ایران ) is faulty copyir.com • The original scanner motor (PM1( کپی ایران )/ original scanner motor driver PCB is faulty copyir.com
• The scanner fails to return to the home position after it has started to operate copyir.com 1( کپی ایران ) When E202 is indicated, is the scanner at home position? NO: See “The scanner fails to move forward/in reverse?” Original scanner home position sensor (PS1( کپی ایران ) 2( کپی ایران ) When the scanner is over PS1, is a 5-VDC output present at J117B- 8 on the reader controller PCB? NO: Check the wiring from the reader controller PCB to PS1; if normal, replace PS1 copyir.com Wiring 3( کپی ایران ) Check the wiring from J113 of the reader controller PCB to J303/ 302 on the original scanner motor driver PCB copyir.com Is there a fault? YES: Correct the wiring copyir.com Original scanner motor driver PCB 4( کپی ایران ) Try replacing the original scanner motor driver PCB copyir.com Is the problem corrected? YES: End copyir.com Original scanner motor (PM1( کپی ایران ), Reader controller PCB 5( کپی ایران ) Try replacing the original scanner motor (PM1( کپی ایران ) copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the reader controller PCB copyir.com
E203 The original scanner motor driver PCB or the original scanner motor is faulty copyir.com
• The original scanner home position is detected during a “back scan” in which the original scanner need not return to its home position copyir.com • The original scanner goes out of synch during a “back scan” in which it returns to its home position copyir.com 1( کپی ایران ) When E203 is indicated, does the scanner move? NO: See “The scanner fails to move forward/in reverse copyir.com Original scanner motor driver PCB, Original scanner motor 1( کپی ایران ) When the scanner starts to move forward, do the voltage between J303-B1 (RST( کپی ایران ) and J303-B4 (GND( کپی ایران ) of the original scanner motor driver PCB and between J303-B2 (MOVE*( کپی ایران ) and J303-B4 (GND( کپی ایران ) change from 5 to 0 V? YES: Try replacing the original scanner motor driver PCB copyir.com If the problem is not corrected, replace the original scanner motor copyir.com NO: Replace the reader controller PCB copyir.com
E211 The scanning lamp (fluorescent lamp( کپی ایران ) thermistor has an open circuit copyir.com
• At a 0°C or lower condition, the temperature fails to reach 10°C after supplying the scanning lamp heater with power for 2 min copyir.com 1( کپی ایران ) Disconnect connector J115 of the reader controller PCB, and measure the resistance between connectors J115-5 (GND( کپی ایران ) and J115-6 (FL-THE( کپی ایران ) on the harness side copyir.com Is it 10 W or less or 100k W or more? NO: The reader controller PCB is faulty copyir.com Go to step 4( کپی ایران ) copyir.com YES: Go to step 2( کپی ایران ) copyir.com Lamp heater 2( کپی ایران ) Disconnect connector J2039 of the lamp heater, and measure the resistance between connectors J2039-2 (GND( کپی ایران ) and J2039-3 (FLTHE( کپی ایران ) of the lamp heater copyir.com Is the resistance 100 W or less or 100k W or more? YES: Replace the lamp heater copyir.com Flat cable and connector (poor contact( کپی ایران ) 3( کپی ایران ) Are connectors J115 of the reader controller PCB, connectors J2037 and J2035 of the flat cable, and connector J2039 of the lamp heater connected securely? NO: Connect them securely copyir.com Reader controller PCB 4( کپی ایران ) When the machine is turned on, is the voltage between HJ122-1 (GNDU( کپی ایران ) and J122-2 (+38 V( کپی ایران ) on the harness side of the connector of the reader controller PCB 38 V? NO: See “The reader unit DC power supply is absent copyir.com” YES: Replace the reader controller PCB copyir.com
E215 The thermistor has a short circuit copyir.com
• The thermistor of the scanning lamp heater registers 170°C or higher when the fluorescent lamp signal (FLON( کپی ایران ) is off (including power-on( کپی ایران ) copyir.com 1( کپی ایران ) Disconnect connector J115 of the reader controller PCB, and measure the resistance between connectors J115-5 (GND( کپی ایران ) and J115-6 (FL-THE( کپی ایران ) on the harness side copyir.com Is it 10 W or less or 100k W or more? NO: The reader controller PCB is faulty copyir.com Go to step 4( کپی ایران ) copyir.com YES: Go to step 2( کپی ایران ) copyir.com Lamp heater 2( کپی ایران ) Disconnect connector J2039 of the lamp heater, and measure the resistance between connectors J2039-2 (GND( کپی ایران ) and J2039-3 (FLTHE( کپی ایران ) of the lamp heater copyir.com Is the resistance 100 W or less or 100k W or more? YES: Replace the lamp heater copyir.com Flat cable and connector (poor contact( کپی ایران ) 3( کپی ایران ) Are connectors J115 of the reader controller PCB, connectors J2037 and J2035 of the flat cable, and connector J2039 of the lamp heater connected securely? NO: Connect them securely copyir.com Reader controller PCB 4( کپی ایران ) When the machine is turned on, is the voltage between HJ122-1 (GNDU( کپی ایران ) and J122-2 (+38 V( کپی ایران ) on the harness side of the connector of the reader controller PCB 38 V? NO: See “The reader unit DC power supply is absent copyir.com” YES: Replace the reader controller PCB copyir.com
E216 The scanning lamp (fluorescent lamp( کپی ایران ) fails to turn on in 15 sec copyir.com
• The light intensify sensor does not detect light from the scanning lamp in 15 sec copyir.com Scanning lamp (life( کپی ایران ) 1( کپی ایران ) Try replacing the scanning lamp copyir.com Is the problem corrected? YES: End copyir.com Inverter PCB, Reader PCB 2( کپی ایران ) Try replacing the inverter PCB copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the reader controller PCB copyir.com
E217 The scanning lamp heater is out of order copyir.com
• When the scanning lamp heater is controlled to a specific temperature, its temperature does not exceed a specific setting when it has been supplied with power for 3 min or more copyir.com Lamp heater 1( کپی ایران ) Try replacing the lamp heater copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the reader controller PCB copyir.com
E219 • The scanning lamp (fluorescent( کپی ایران ) has reached the end of its life copyir.com
• The scanning lamp thermistor detects 150°C or higher when the scanning lamp is on copyir.com Scanning lamp (life( کپی ایران ) 1( کپی ایران ) Try replacing the scanning lamp copyir.com Is the problem corrected? YES: End copyir.com Inverter PCB, Reader PCB 2( کپی ایران ) Try replacing the inverter PCB copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the reader controller PCB copyir.com
E220 The scanning lamp (fluorescent( کپی ایران ) is faulty copyir.com
• The light of the scanning lamp fails to reach a specific level of intensity within 10 sec after it has been turned on copyir.com Scanning lamp 1( کپی ایران ) Is the scanning lamp mounted correctly? NO: Mount the scanning lamp correctly copyir.com (Caution( کپی ایران ) 2( کپی ایران ) Try replacing the scanning lamp copyir.com Is the problem corrected? YES: Replace the scanning lamp copyir.com Inverter PCB 3( کپی ایران ) Are connectors J1002 and J1003 on the inverter PCB and connector J129 on the reader controller PCB connected securely? NO: Connect the connectors securely copyir.com YES: Replace the inverter PCB copyir.com Caution: • If you have to remove the scanning lamp and mount it back, be sure to execute the following in service mode: Function>MISC-R>USELAMP copyir.com • If you have mounted a new scanning lamp, be sure to execute the following in service mode: Function>MISC-R>LAMP-ADJ for light intensity adjustment and then Function>CCD>CCD-ADJ copyir.com
E400 The communication with the ADF has an error copyir.com
• No signal is returned by the ADF 1 sec or more after communication with the ADF has started copyir.com Perfrom the work according to the instructions in the service manual of the feeder copyir.com
E401 • The pickup motor (M1( کپی ایران ) fails to rotate copyir.com • The pickup roller sensor (S5( کپی ایران ) is faulty copyir.com
• A flag is attached to the spindle of the pickup motor (M1( کپی ایران ), and the rotation of the motor is monitored with reference to the flag (blocking the pickup roller sensor S5( کپی ایران ) copyir.com The pickup roller sensor fails to turn on and off twice or more in within 1 sec copyir.com Perfrom the work according to the instructions in the service manual of the feeder copyir.com
E402 • The belt motor (M3( کپی ایران ) fails to rotate copyir.com • The belt motor clock senor (S10( کپی ایران ) is faulty copyir.com
• The number of feeder motor clock puleses within 200 msec is below a specific value copyir.com Perfrom the work according to the instructions in the service manual of the feeder copyir.com
E403 • The feed motor (M2( کپی ایران ) fails to rotate copyir.com • The feed motor clock sensor (S9( کپی ایران ) is faulty copyir.com
• The number of belt motor clock pulses is below a specific value for 200 msec copyir.com Perfrom the work according to the instructions in the service manual of the feeder copyir.com
E404 • The delivery motor (M5( کپی ایران ) fails to rotate copyir.com • The delivery motor clock sensor (S13( کپی ایران ) is faulty copyir.com
• The number of delivery motor clock puleses within 200 msec is below a specific value copyir.com Perfrom the work according to the instructions in the service manual of the feeder copyir.com
E421 Communication with the ADF is faulty
•The communication with the ADF remains interrupted for 5 sec or more copyir.com Perfrom the work according to the instructions in the service manual of the feeder copyir.com
E500 Finisher Data communication
• The communication between the machine and the finisher is interrupted copyir.com This error is detected by the machine copyir.com
E503-03 Communication error
• The communication with the saddle stitcher is interrupted copyir.com
E504-01 Height sensor (PS1( کپی ایران )
• The communication between the height sensor and the finisher controller PCB fails copyir.com Or, an error exists in the communication data copyir.com
E504-02 Height sensor (PS1( کپی ایران )
• The communication between the sensor and the finisher controller PCB fails for a specific period of time or more copyir.com
E504-03 Height sensor (PS1( کپی ایران )
• The connector is found to be disconnected at poweron copyir.com
E504-04 Height sensor (PS1( کپی ایران )
• An error occurs when the sensor is adjusted using the DIP switch copyir.com
E505-01 Back-up RAM
• An error exits in the check sum at power-on copyir.com
E512-01 • Delivery motor (M2( کپی ایران ) • Delivery motor clock sensor (PI10( کپی ایران )
• The delivery motor clock sensor does not send the target number of clock pulses at the start of operation copyir.com
E512-02 • Delivery motor (M2( کپی ایران ) • Delivery motor clock sensor (PI10( کپی ایران )
• The clock pulses sent while paper is being moved fall short of an equivalent of 200 mm in length copyir.com
E513-01 • Alignment motor (M3( کپی ایران ) • Alignment plate home position sensor (PI6( کپی ایران )
• The alignment plate does to leave the alignment home position sensor when the alignment motor is driven for 2 sec copyir.com
E513-02 • Alignment motor (M3( کپی ایران ) • Alignment plate home position sensor (PI6( کپی ایران )
• The alignment plate does not return to the alignment home position when the alignment motor is driven for 2 sec copyir.com
E531-01 • Stapler motor (M6( کپی ایران ) • Stapler motor home position detecting switch (MS7( کپی ایران )
• The stapler does not leave the stapler home position when the stapler motor is driven for 0 copyir.com5 sec copyir.com
E531-02 • Stapler motor (M6( کپی ایران ) • Stapler motor home position detecting switch (MS7( کپی ایران )
• The stapler does not leave the stapler home position when the stapler motor is driven for 0 copyir.com5 sec copyir.com
E532-01 • Stapler drive motor (M4( کپی ایران ) • Stapler drive home position sensor (PI7( کپی ایران )
• The stapler drive home position sensor does not turn off when the stapler drive motor is driven for 4 sec copyir.com
E532-02 • Stapler drive motor (M4( کپی ایران ) • Stapler drive home position sensor (PI7( کپی ایران )
• The stapler drive home position is not detected when the stapler drive motor is driven for 4 sec copyir.com
E535-01 • Delivery motor (M2( کپی ایران ) • Swing guide closed detecting switch (MS6( کپی ایران )
• The swing guide closed detecting switch does not turn on when the delivery motor is rotated in reverse for 1 sec copyir.com
E535-02 • Delivery motor (M2( کپی ایران ) • Swing guide open sensor (PI18( کپی ایران )
• The swing guide open detecting sensor does not turn on when the delivery motor is rotated in reverse for 1 sec copyir.com
E535-03 • Safety area switch (MS3( کپی ایران ) • Swing guide closed detection switch (MS6( کپی ایران )
• The swing guide closed detecting switch is found to be off when the tray 1/2 is in the safety area switch OFF position copyir.com
E540-01 • Tray lift motor (M5( کپی ایران ) • Tray lift motor clock sensor 1/ 2 (PI19/PI9( کپی ایران ) • Tray home position sensor (PI8( کپی ایران )
• The lift operation does not end within 15 sec when the tray lift motor is driven copyir.com • The tray home position is not detected when the tray lift motor is driven for 15 sec copyir.com
E540-02 • Tray upper limit detecting switch (MS4( کپی ایران )
• The tray upper limit detecting switch is found to be on while the tray is moving up copyir.com
E540-03 • Tray lift motor (M5( کپی ایران ) • Tray lift motor clock sensor 1/ 2 (PI19/PI9( کپی ایران )
•The clock sensor 1/2 does not send clock pulses for 200 msec when the tray lift motor is driven copyir.com
E584-01 • Feed motor (M1( کپی ایران ) • Shutter closed detecting switch (MS4( کپی ایران )
• The shutter closed detecting switch does not turn on when the feed motor is rotated in reverse for 1 sec or more copyir.com
E584-02 • Feed motor switch (M1( کپی ایران ) • Shutter closed detecting switch (MS4( کپی ایران )
• The shutter open sensor does not turn on when the feed motor is rotated in reverse for 1 sec or more copyir.com
E584-03 • Safety area detecting switch (MS3( کپی ایران ) • Shutter closed detecting switch (MS4( کپی ایران )
• The shutter closed detecting switch is found to be off when the tray 1/2 is in the safety area switch OFF position copyir.com
E606 The HDD is faulty copyir.com
• The HDD cannot be recognized normally at power-on copyir.com • An error occurs while writing to or reading from the HDD copyir.com B? Connector (poor contact( کپی ایران ) 1( کپی ایران ) Are connectors J701 and J702 of the HDD and connectors J306 and J307 of the relay PCB connected securely? NO: Connect the connectors securely copyir.com Relay PCB 2( کپی ایران ) Is connector J301 of the relay PCB and J1017 of the system controller PCB connected securely? NO: Connect them securely copyir.com HDD, System controller PCB 3( کپی ایران ) Try replacing the HDD copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E676 The PDL PCB has a communication error copyir.com
• The communication with the PDL PCB fails in initialization sequence copyir.com • The registration of the PDL-unique menu fails copyir.com • While PDL is in operation, a check sum error of the received packet is detected copyir.com • While PDL is in operation, a format error in the received packet is detected copyir.com • There is no response in the course of a check on the PDL board operation copyir.com Connector (poor contact( کپی ایران ) 1( کپی ایران ) Is the PDL PCB securely connected to J303 of the relay PCB? NO: Connect it securely copyir.com Relay PCB 2( کپی ایران ) Are connector J301 of the relay PCB and connector J1017 of the system controller PCB connected securely? NO: Connect the connectors securely copyir.com PDL PCB, System controller PCB 3( کپی ایران ) Try replacing the PDL PCB copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E677 The PDL PCB is faulty copyir.com
• An error occurs on the PDL board copyir.com Connector (poor contact( کپی ایران ) 1( کپی ایران ) Is the PDL PCB securely connected to J303 of the relay PCB? NO: Connect it securely copyir.com Relay PCB 2( کپی ایران ) Are connector J301 of the relay PCB and connector J1017 of the system controller PCB connected securely? NO: Connect the connectors securely copyir.com PDL PCB, System controller PCB 3( کپی ایران ) Try replacing the PDL PCB copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E710 The initialization of the IPC fails copyir.com
• At power-on or during sleep return, initialization communication with the finisher fails copyir.com 1( کپی ایران ) Turn off and then on the power copyir.com Is the problem corrected? YES: End copyir.com If the problem occurs frequently, check the communication cable to the finisher copyir.com Connector (poor contact( کپی ایران ) 2( کپی ایران ) Is the connection between the machine and the finisher secure? NO: Make the connection secure copyir.com Communication cable 3( کپی ایران ) Try replacing the communication cable to the finisher copyir.com Is the problem corrected? YES: End copyir.com Finisher controller PCB, System controller PCB 4( کپی ایران ) Try replacing the finisher controller PCB of the finisher copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E711 An IPC register error occurs copyir.com
• An error occurs frequently in the communication between the finisher and the machine copyir.com 1( کپی ایران ) Turn off and then on the power copyir.com Is the problem corrected? YES: End copyir.com If the problem occurs frequently, check the communication cable to the finisher copyir.com Connector (poor contact( کپی ایران ) 2( کپی ایران ) Is the connection between the machine and the finisher secure? NO: Make the connection secure copyir.com Communication cable 3( کپی ایران ) Try replacing the communication cable to the finisher copyir.com Is the problem corrected? YES: End copyir.com Finisher controller PCB, System controller PCB 4( کپی ایران ) Try replacing the finisher controller PCB of the finisher copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E712 An error occurs in IPC communication copyir.com
• In communication with the ADF, four or more errors occur in 1 copyir.com5 sec or more copyir.com 1( کپی ایران ) Turn off and then on the power copyir.com Is the problem corrected? YES: End copyir.com If the problem occurs frequently, check the communication cable to the finisher copyir.com Connector (poor contact( کپی ایران ) 2( کپی ایران ) Is the connection between the machine and the finisher secure? NO: Make the connection secure copyir.com Communication cable 3( کپی ایران ) Try replacing the communication cable to the finisher copyir.com Is the problem corrected? YES: End copyir.com Finisher controller PCB, System controller PCB 4( کپی ایران ) Try replacing the finisher controller PCB of the finisher copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E713 An IPC finisher error occurs copyir.com
• The communication between the finisher and the machine remiains interrupted for 3 sec copyir.com 1( کپی ایران ) Turn off and then on the power copyir.com Is the problem corrected? YES: End copyir.com If the problem occurs frequently, check the communication cable to the finisher copyir.com Connector (poor contact( کپی ایران ) 2( کپی ایران ) Is the connection between the machine and the finisher secure? NO: Make the connection secure copyir.com Communication cable 3( کپی ایران ) Try replacing the communication cable to the finisher copyir.com Is the problem corrected? YES: End copyir.com Finisher controller PCB, System controller PCB 4( کپی ایران ) Try replacing the finisher controller PCB of the finisher copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E731 The PDL PCB PCI error occurs copyir.com
• The PDL PCB cannot be recognized at power-on copyir.com Connector (poor contact( کپی ایران ) 1( کپی ایران ) Are the network PCB, PDL PCB, relay PCB, system controller PCB, and image processor PCB connected securely? NO: Connect them securely copyir.com Relay PCB 2( کپی ایران ) Try replacing the relay PCB copyir.com Is the problem corrected? YES: End copyir.com PDL PCB 3( کپی ایران ) Try replacing the PDL PCB copyir.com Is the problem corrected? YES: End copyir.com Network PCB 4( کپی ایران ) Try replacing the network PCB copyir.com Is the problem corrected? YES: End copyir.com Image processor PCB, System controller PCB 5( کپی ایران ) Try replacing the image processor PCB copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E732 A controller reader communication error occurs copyir.com
• An error occurs in the communication between the controller unit and the reader unit copyir.com Communication cable 1( کپی ایران ) Is the communication cable between the reader and the controller connected securely? NO: Connect the cable securely copyir.com 2( کپی ایران ) Try replacing the communication cable copyir.com Is the problem corrected? YES: Replace the communication cable copyir.com Reader unit power supply 3( کپی ایران ) Is the reader unit power supply normal? NO: See “The reader unit power supply is absent copyir.com” Interface PCB 4( کپی ایران ) Are connectors J102 of the interface PCB and J132 of the reader controller PCB connected securely? NO: Connect the connectors securely copyir.com 5( کپی ایران ) Try replacing the interface PCB copyir.com Is the problem corrected? YES: Replace the interface PCB copyir.com Reader controller PCB 6( کپی ایران ) Try replacing the reader controller PCB copyir.com Is the problem corrected? YES: Replace the reader controller PCB copyir.com NO: Replace the image processor PCB copyir.com
E733 A controller printer unit communication error occurs copyir.com
• The PPRDY signal cannot be detected from the printer unit 15 sec after the end of start-up sequence copyir.com Connector (poor contact( کپی ایران ) 1( کپی ایران ) Is the controller unit mounted to the printer unit securely? NO: Mount it correctly copyir.com 2( کپی ایران ) Are connector J1015 on the system controller PCB and connector J501 on the image processor PCB connected securely? NO: Connect the connectors securely copyir.com Printer unit power supply 3( کپی ایران ) Does the printer unit execute initialization when the power is turned on? NO: See “The printer unit power supply is absent copyir.com” DC controller PCB 4( کپی ایران ) Can the printer unit be operated using the printer checker driver? NO: Replace the DC controller PCB Controller unit 5( کپی ایران ) Try replacing the image processor PCB copyir.com Is the problem corrected? YES: Replace the image processor PCB copyir.com NO: System controller PCB
E734 An image processor PCB check error occurs copyir.com
• The image processor PCB cannot be recognized normally copyir.com Connector (poor contact( کپی ایران ) 1( کپی ایران ) Are the network PCB, PDL PCB, relay PCB, system controller PCB, and image processor PCB connected securely? NO: Connect them securely copyir.com Relay PCB 2( کپی ایران ) Try replacing the relay PCB copyir.com Is the problem corrected? YES: End copyir.com PDL PCB 3( کپی ایران ) Try replacing the PDL PCB copyir.com Is the problem corrected? YES: End copyir.com Network PCB 4( کپی ایران ) Try replacing the network PCB copyir.com Is the problem corrected? YES: End copyir.com Image processor PCB, System controller PCB 5( کپی ایران ) Try replacing the image processor PCB copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E735 An EIF PCI error occurs copyir.com
• The image processor PCB cannot be recognized normally copyir.com Connector (poor contact( کپی ایران ) 1( کپی ایران ) Are the network PCB, PDL PCB, relay PCB, system controller PCB, and image processor PCB connected securely? NO: Connect them securely copyir.com Relay PCB 2( کپی ایران ) Try replacing the relay PCB copyir.com Is the problem corrected? YES: End copyir.com PDL PCB 3( کپی ایران ) Try replacing the PDL PCB copyir.com Is the problem corrected? YES: End copyir.com Network PCB 4( کپی ایران ) Try replacing the network PCB copyir.com Is the problem corrected? YES: End copyir.com Image processor PCB, System controller PCB 5( کپی ایران ) Try replacing the image processor PCB copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E736 A fax PCB communication error occurs copyir.com
• The communication with the FAX PCB fails copyir.com Connector (poor contact( کپی ایران ) 1( کپی ایران ) Are connector J304 and J305 on the relay PCB and relay connector J803 connected securely? NO: Connect the connectors securely copyir.com 2( کپی ایران ) Are connector J301 on the relay PCB and connector J1017 on the system controller PCB connected securely? NO: Connect the connectors securely copyir.com FAX PCB 3( کپی ایران ) Replace the FAX PCB copyir.com Is the problem corrected? YES: Replace the FAX PCB copyir.com NO: Replace the system controller PCB copyir.com
E737 A main memory error occurs copyir.com
• Writing to the main memory fails at power-on copyir.com DIMM (controller( کپی ایران ) 1( کپی ایران ) Is the DIMM in the controller fitted to the socket firmly? NO: Fit it firmly copyir.com 2( کپی ایران ) Try replacing the DIMM in the controller copyir.com Is the problem corrected? YES: Replace the DIMM copyir.com NO: Replace the system controller PCB copyir.com
E738 A network interface initialization error occurs copyir.com
• Initialization of the network PCB fails at power-on copyir.com Connection (poor contact( کپی ایران ) 1( کپی ایران ) Is the network PCB connected to the relay PCB securely? NO: Connect it securely copyir.com Relay PCB 2( کپی ایران ) Is connector J301 of the relay PCB connected to connector J1017 of the system controller PCB securely? NO: Connect the connector securely copyir.com Network PCB 3( کپی ایران ) Try replacing the network PCB copyir.com Is the problem corrected? YES: End copyir.com Relay PCB, System controller PCB 4( کپی ایران ) Try replacing the relay PCB copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E739 A network interface communication error occurs copyir.com
• The communication with the network PCB fails at power-on copyir.com
E741 A network PCI error occurs copyir.com
• The network PCB cannot be recognized at power-on Connection (poor contact( کپی ایران ) 1( کپی ایران ) Is the network PCB connected to the relay PCB securely? NO: Connect it securely copyir.com Relay PCB 2( کپی ایران ) Is connector J301 of the relay PCB connected to connector J1017 of the system controller PCB securely? NO: Connect the connector securely copyir.com Network PCB 3( کپی ایران ) Try replacing the network PCB copyir.com Is the problem corrected? YES: End copyir.com Relay PCB, System controller PCB 4( کپی ایران ) Try replacing the relay PCB copyir.com Is the problem corrected? YES: End copyir.com NO: Replace the system controller PCB copyir.com
E804 A printer power supply cooling fan error occurs copyir.com
• An error occurs in the rotation of the printer power supply cooling fan (FAN2( کپی ایران ) Connector (poor contact( کپی ایران ) 1( کپی ایران ) Is connector J216 on the DC controller PCB connected securely? NO: Connect it securely copyir.com Printer unit power supply cooling fan (FM2( کپی ایران ) 2( کپی ایران ) Disconnect J210 of the DC controller PCB copyir.com Does the voltage between connectors J216-1 (FAN2D( کپی ایران ) and J2163 (GND( کپی ایران ) of the DC controller PCB change from 0 to about 18 V immediately after the power switch is turned on? YES: Replace the printer unit power supply cooling fan copyir.com NO: Replace the DC controller PCB copyir.com
E805 A fixing assembly/scanner fan error occurs copyir.com
• An error occurs in the rotation of the fixing assembly fan (FAN4( کپی ایران ) Connector (poor contact( کپی ایران ) 1( کپی ایران ) Are connector J225 on the DC controller PCB and relay connectors J25 and J26 connected securely? NO: Connect the connectors securely copyir.com Fixing assembly fan (FAN4( کپی ایران ) 2( کپی ایران ) Disconnect J225 from the DC controller PCB copyir.com Does the voltage between connectors J225-1 (FAN4D( کپی ایران ) and J225-03 (GND( کپی ایران ) on the DC controller PCB change from 0 to about 18 V immediately after the power switch is turned on? YES: Replace the fixing assembly fan (FM4( کپی ایران ) copyir.com NO: Replace the DC controller PCB copyir.com
E807 A fixing assembly/scanner fan error occurs copyir.com
• An error occurs in the rotation of the fixing assembly/scanner fan (FAN1( کپی ایران ) copyir.com Connector (poor contact( کپی ایران ) 1( کپی ایران ) Is connector J208 on the DC controller PCB connected securely? NO: Connect the connector securely copyir.com Fixing/scanning fan (FAN1( کپی ایران ) 2( کپی ایران ) Disconnect J208 of the DC controller PCB copyir.com Does the voltage between connectors J208-1 (FAN1D( کپی ایران ) and J208-3 (GND( کپی ایران ) change from 0 to about 18 V immediately after the power switch is turned on? YES: Replace the fixing/scanner fan (FM1( کپی ایران ) copyir.com NO: Replace the DC controller PCB copyir.com
E826 A multifeeder cooling fan error occurs copyir.com
• An error occurs in the rotation of the multifeeder tray fan (FAN5( کپی ایران ) copyir.com Connector (poor contact( کپی ایران ) 1( کپی ایران ) Are connector J229 on the DC controller PCB and relay connectors J34 and J35 connected securely? NO: Connect the connectors securely copyir.com Multifeeder tray fan (FM5( کپی ایران ) 2( کپی ایران ) Disconnect J229 from the DC controller PCB copyir.com Does the voltage between connectors J229-1 (FAN5D( کپی ایران ) and J229-3 (GND( کپی ایران ) on the DC controller PCB change from 0 to bout 18 V immediately after the power switch is turned on? YES: Replace the multifeeder tray fan (FM5( کپی ایران ) copyir.com NO: Replace the DC controller PCB copyir.com
E827 A controller power supply fan error occurs
• An error occurs in the rotation of controller power supply fan (FAN6( کپی ایران ) copyir.com
E903 Paper Deck Lifter (faulty( کپی ایران )
• The communication with the paper deck is interrupted copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهره‌برداری از آن مستلزم کسب اجازه می‌باشد.