لمینت MKP
1402-06-04
Menu
E000-0010 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
After power-on, the temperature does not reach 50 deg C within 300 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0011 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 50 deg C, but does not reach 80 deg C within 300 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0012 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 80 deg C, but does not reach 110 deg C within 300 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0013 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 110 deg C, but does not reach 140 deg C within 300 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0014 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 140 deg C, but does not reach 170 deg C within 300 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0015 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 170 deg c, but does not reach 200 deg C within 300 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0020 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
After power-on, the temperature does not reach 50 deg C within 180 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0021 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 50 deg C, but does not reach 80 deg C within 180 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0022 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 80 deg C, but does not reach 110 deg C within 180 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0023 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 110 deg C, but doest not reach 140 deg C within 180 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0024 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 140 deg C, but does not reach 170 deg C within 180 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0025 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 170 deg C, but does not reach 200 deg C within 180 sec copyir.ocm If the outside heating roller is in contact, within 400 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0026 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 200 deg C, but does not reach 230 deg C within 180 sec copyir.ocm If the outside heating roller is in contact, within 400 sec Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0026 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 200 deg C, but does not reach 230 deg C within 180 sec copyir.ocm If the outside heating roller is in contact, within 400 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0030 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
After power-on, the temperature does not reach 50 deg C within 420 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0031 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 50 deg C, but does not reach 80 C deg in 420 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0032 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 80 deg C, but does not reach 110 deg C within 420 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0033 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 110 deg C, but does not reach 140 deg C within 420 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E000-0034 At power-on, the rise in the temperature of the fixing assembly is not high enough copyir.ocm The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact copyir.ocm The AC drive PCB or the DC controller PCB is faulty copyir.ocm
The temperature reaches 140 deg C, but does not reach 170 deg C within 420 sec copyir.ocm Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E001-0001 The rise in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB is faulty copyir.ocm
The rise in the temperature of the fixing roller is excessive copyir.ocm Check the main thermistor, sub thermistor, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E001-0002 The rise in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB is faulty copyir.ocm
The rise in the temperature of the outside heating roller is excessive copyir.ocm Check the main thermistor, sub thermistor, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E001-0003 The rise in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB is faulty copyir.ocm
The rise in the temperature of the pressure roller is excessive copyir.ocm Check the main thermistor, sub thermistor, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E001-00FF The rise in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB is faulty copyir.ocm
When the cause (Detailed code) cannot be found in the DC controller PCB input-port as DC controller PCB detects instantly an abnormal signal from the thermistor copyir.ocm After releasing the error with the procedure of COPIER>FUNCTION>CLEAR>ERR, 1 copyir.ocm Turn off the switch of control panel copyir.ocm 2 copyir.ocm Turn off the switch of main power copyir.ocm 3 copyir.ocm Turn on the switch of main power copyir.ocm a copyir.ocm When the machine returns, Check the interconnection between the DC controller PCB and the thermistor copyir.ocm b copyir.ocm When the machine does not return, Follow the instruction the error (Detailed) code shows on the control panel copyir.ocm
E002-0010 The rise in the temperature of the fixing assembly is not enough copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
The temperature of the fixing roller reaches 80 deg C, but drops below 50 deg C copyir.ocm Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E002-0020 The rise in the temperature of the fixing assembly is not enough copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
The temperature of the outside heating roller reaches 80 deg C, but drops below 50 deg C copyir.ocm Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E002-0030 The rise in the temperature of the fixing assembly is not enough copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
The temperature of the pressure roller reaches 80 deg C, but drops below 50 deg C copyir.ocm Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E003-0041 After standby, the drop in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
During standby, the temperature of the fixing roller drops below 150 deg C copyir.ocm Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E003-0042 After standby, the drop in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
During standby, the temperature of the outside heating roller drops below 190 dg C copyir.ocm Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E003-0043 After standby, the drop in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
During standby, the temperature of the pressure roller drops below 120 deg C copyir.ocm Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E003-0051 After standby, the drop in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
During copying, the temperature of the fixing roller drops below 150 deg C copyir.ocm Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
03-0052 After standby, the drop in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
During copying, the temperature of the outside heating roller drops below 190 deg C copyir.ocm Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E003-0053 After standby, the drop in the temperature of the fixing assembly is excessive copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
During copying, the temperature of the pressure roller drops below 60 deg C copyir.ocm Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0001 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the outside heating roller heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0002 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the fixing sub heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0003 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the outside heating roller heater or the fixing sub heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0004 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the fixing main heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0005 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the outside heating roller heater or the fixing main heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0006 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the fixing sub heater or the fixing main heater Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0007 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the outside heating roller heater, fixing sub heater, or fixing main heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0008 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the pressure heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0009 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the outside heating roller heater or the contact heater Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-000A There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the fixing sub heater or the contact heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-000B There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the outside heating roller heater, fixing sub heater, or contact heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-000C There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an error in the fixing main heater or the contact heater Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-000D There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the outside heating roller heater, fixing main heater, or contact heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-000E There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an error in the fixing sub heater, fixing main heater, or contact heater copyir.ocmN>CLEAR>ERR copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-000F There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
There is an SSR error in the outside heating roller heater, fixing sub heater, fixing main heater, or contact heater copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0010 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
The fixing roller thermistor has an open circuit copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0020 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
The outside heating roller thermistor has an open circuit copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E004-0030 There is an error in the fixing assembly protection circuit copyir.ocm There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6) copyir.ocm The AC driver PCB or the DC controller PCB has a fault copyir.ocm
The pressure roller thermistor has an open circuit copyir.ocm Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E005-0000 There is an error in the take-up mechanism of the web copyir.ocm
The web of the fixing assembly has been fully taken up copyir.ocm After the web sensor has detected an off state, the count has exceeded 3000 copyir.ocm The web length sensor (PS20) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm Reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm If you have replaced the web, reset the reading in the following, and turn off and then on the power: COPIER>COUNTER>DRBL-1>FIX-WEB copyir.ocm
E005-0010 There is an error in the take-up mechanism of the web copyir.ocm
The drive solenoid of the fixing assembly is not connected copyir.ocm Check the drive solenoid of the fixing web for disconnection; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E006-0001 The fixing assembly has a comparison error copyir.ocm
The fixing drawer has been identified as being disconnected copyir.ocm Check the connector of the drive solenoid of the fixing web; then, turn off and then on the main power copyir.ocm
E008-0001 There is an error in relation to the life of the fixing assembly copyir.ocm
The counter reading for the fixing roller has exceeded a specific count When you have replaced the fixing roller, reset in service mode, and turn off and then on the main power: COPIER>COUNTER>DRBL-1>FX-UP-RL copyir.ocm
E009-00FF There is an outside heating roller shift error copyir.ocm The outside heating roller shift motor (M22) is faulty copyir.ocm The outside heating roller HP sensor (PS21) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The outside heating roller remains in contact with the fixing roller Check the outside heating roller shift motor and the fixing motor; then, turn off and then on the main power copyir.ocm
E012-0001 There is an error in the drum/ITB motor copyir.ocm
After motor start-up, a lock state is not identified for 1 sec or more copyir.ocm Check the area around the photosensitive drum and the intermediate transfer belt; then, turn off and then on the main power copyir.ocm
E013-0001 There is clogging by waste toner copyir.ocm
There is a waste toner full error copyir.ocm the soft counter reading is 250000 or higher copyir.ocm Check the amount of waste toner; then, turn off and then on the main power copyir.ocm
E013-0002 There is clogging by waste toner copyir.ocm
There is a waste toner feedscrew error copyir.ocm The output of the waste toner lock detecting switch (SW14) is ‘1’ for more than 1 sec copyir.ocm Check the developing motor; then, turn off and then on the main power copyir.ocm
E014-0001 There is a fixing motor error copyir.ocm
After motor start-up, a lock state is not identified for 1 sec or more copyir.ocm Check the fixing motor (fixing assembly); then, turn off and then on the main power copyir.ocm
E020-xx10 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Sig value is lower than 62 copyir.ocm The ATR sensor is damage or has an open circuit copyir.ocm The connector may have poor contact copyir.ocm The intermediate transfer belt may be soiled copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
020-xx11 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62 copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector may have poor contact copyir.ocm The intermediate transfer belt may be soiled Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xx11 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62 copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector may have poor contact copyir.ocm The intermediate transfer belt may be soiled Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xx12 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Sig value is 960 or higher copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The opening/closing of the shutter is faulty copyir.ocm The intermediate transfer belt is soiled copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xx13 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Ref value is 960 or higher copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The intermediate transfer belt is soiled Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xx81 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
When the background (intermediate transfer belt) is read during patch detection, the P_base_adj value is lower than 255 copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The ITB cleaner is faulty copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xx90 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The result (Sig D) of computation based on the reading of the patch during patch detection (analog)) is lower than 16 copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xx91 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The result (Sig D) of computation based on the reading of the patch during patch detection (analog) is 1008 or higher copyir.ocm The patch sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The primary transfer pressure is faulty copyir.ocm The mounting of the developing assembly is faulty copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xx92 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The value delta D obtained from the result (Sig D) of computation based on the reading of the patch during patch detection is -5 copyir.ocm0% or more 3 times continuously copyir.ocm The patch sensor may be damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The primary transfer engagement is faulty copyir.ocm The mounting of the developing assembly is faulty copyir.ocm The amount of supply is low copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xx93 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The value delta D obtained from the result (Sig D) of computation based on the reading of the patch during patch detection is +5 copyir.ocm0% or lower 3 times continuously copyir.ocm The patch sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The primary transfer pressure is faulty copyir.ocm The mounting of the developing assembly is faulty copyir.ocm The amount of supply is low copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxA0 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Sig value is lower than 62 copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxA1 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Ref value is lower than 62 copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxA1 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Ref value is lower than 62 copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxA2 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Sig value is 960 or higher copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The opening/closing of the shutter is faulty copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxA3 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Ref value is 960 or higher copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxA9 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The T/D ratio identified for ATR control has exceeded the lower limit (3%) 3 times continuously copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The amount of supply is too low copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxC0 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The variation among the 8 samplings of the light Sig value is 100 or higher copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The stirring of toner is faulty copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxC1 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The variation among the 8 samplings of the light Ref value is 100 or higher copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxC2 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The variation among the 8 samplings of the patch Sig value is 400 or higher copyir.ocm The patch sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The primary transfer engagement is faulty Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxD0 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 200 or lower copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The amount of supply is low copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxD0 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 200 or lower copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The amount of supply is low copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxD1 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 462 or lower copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxD2 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
Fore INIT control (service mode INISET-*) at time of initial setup, the average of the patch Sig values is 200 or lower copyir.ocm The patch sensor is damaged or has an open circuit copyir.ocm the connector has poor contact copyir.ocm The primary transfer engagement is faulty copyir.ocm The mounting of the developing assembly is faulty copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxD4 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INTI control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 800 or higher copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The amount of supply is too high copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxD5 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INTI control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 562 or higher copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxDA There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the variation among the 72 night Sig value samplings is 100 or more copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm The stirring of toner is faulty copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxDB There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the variation among the 72 light Ref samplings is 100 or more copyir.ocm The ATR sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxDC There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*), the average of the patch Sig values is 800 or higher copyir.ocm The patch sensor is damaged or has an open circuit copyir.ocm The connector has poor contact copyir.ocm the primary transfer engagement if faulty copyir.ocm The mounting of the developing assembly is faulty copyir.ocm The amount of supply is too high copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E020-xxF1 There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The connector or the color toner supply clutch is not connected copyir.ocm Turn off and then on the main power; then, execute ITB cleaning copyir.ocm
E020-xxFF There is an ATR error copyir.ocm xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
There is no toner inside the Bk developing assembly copyir.ocm – the toner is not supplied to the developing assembly correctly copyir.ocm – the hopper stirring motor is not rotating normally copyir.ocm The hopper connector has poor contact copyir.ocm The black toner supply motor (M25) is faulty copyir.ocm The hopper stirring motor (M23) is faulty copyir.ocm The black toner level sensor is faulty copyir.ocm The DC controller is faulty copyir.ocm Turn off and then on the main power; then, execute the intermediate transfer belt copyir.ocm
E021-0001 There is an error in the rotation of the developing assembly copyir.ocm
The developing rotary home position is not detected copyir.ocm The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is faulty; the wiring of the DC controller is faulty; there is an excess load on the developing assembly copyir.ocm Turn off and then on the main power copyir.ocm
E021-0002 There is an error in the rotation of the developing assembly copyir.ocm
The length of the flag detected during rotation is longer or shorter than the designed flag copyir.ocm The motor rotates out of sync because of poor torque caused by any of the following: the developing rotary HP sensor is faulty; the wiring of the DC controller PCB is faulty; there is an excessive load on the developing assembly copyir.ocm Turn off and then on the main power copyir.ocm
E023-0001 The developing motor (M3) does not rotate normally copyir.ocm
After motor start-up, a lock state is not detected for 1 sec or more copyir.ocm Turn off and then on the main power copyir.ocm
E025-0001 There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25) copyir.ocm
There is an overcurrent in the hopper stirring motor (M23) copyir.ocm Turn off and then on the main power copyir.ocm
E025-0002 There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25) copyir.ocm
There is an over-current in the black toner supply motor (M25) copyir.ocm Turn off and then on the main power copyir.ocm
E025-0410 There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25) copyir.ocm
The connector of the black toner supply motor (M25) is identified as being disconnected copyir.ocm Turn off and then on the main power copyir.ocm
E032-0001 The NE connector counter does not operate copyir.ocm
There is an open circuit in the line for the count pulse signal copyir.ocm Turn off the main power, and check the cable for an open circuit; then, turn on the main power copyir.ocm
E043-0001 There is an error in the 3 copyir.ocm5K paper deck pickup motor, causing an error signal copyir.ocm
After motor start-up, a lock state is not detected for 1 sec or more copyir.ocm The mechanical load such as on the feeding system is excessive copyir.ocm Turn off and then on the main power copyir.ocm
E051-0001 The horizontal registration home position is not detected within a specific period of time copyir.ocm The horizontal registration position is faulty (0003) copyir.ocm
The horizontal registration home position is not detected within a specific period of time copyir.ocm Turn off and then on the main power copyir.ocm
E051-0002 The horizontal registration home position is not detected within a specific period of time copyir.ocm The horizontal registration position is faulty (0003) copyir.ocm
The ON edge of the SUS plate is not detected during a search for home position copyir.ocm Turn off and then on the main power copyir.ocm
E051-0003 The horizontal registration home position is not detected within a specific period of time copyir.ocm The horizontal registration position is faulty (0003) copyir.ocm
The logical motor position differs between before and after the detection operation copyir.ocm Turn off and then on the main power copyir.ocm
E061-0001 At time of potential control, a specific level of potential is absent copyir.ocm Or, the limiter goes on copyir.ocm
When forming an image, the potential is 10 V or less during initial rotation copyir.ocm Turn off and then on the main power copyir.ocm
E061-0002 At time of potential control, a specific level of potential is absent copyir.ocm Or, the limiter goes on copyir.ocm
At time of potential control, the potential is 10 V or less during initial rotation Turn off and then on the main power copyir.ocm
E061-0003 At time of potential control, a specific level of potential is absent copyir.ocm Or, the limiter goes on copyir.ocm
While the grid bias is being adjusted, a level of potential higher than the grid bias is sampled copyir.ocm Turn off and then on the main power copyir.ocm
E061-0005 At time of potential control, a specific level of potential is absent copyir.ocm Or, the limiter goes on copyir.ocm
The difference in potential between dark and light areas is less than 100 V copyir.ocm Turn off and then on the main power copyir.ocm
E061-0007 At time of potential control, a specific level of potential is absent copyir.ocm Or, the limiter goes on copyir.ocm
During adjustment of EPC offset, the potential that is read is outside the +/-30 V range copyir.ocm Turn off and then on the main power copyir.ocm
E061-0008 At time of potential control, a specific level of potential is absent copyir.ocm Or, the limiter goes on copyir.ocm
During dark area potential adjustment, the sampling value is too low copyir.ocm Turn off and then on the main power copyir.ocm
E061-0010 At time of potential control, a specific level of potential is absent copyir.ocm Or, the limiter goes on copyir.ocm
The sampling of the light area potential is faulty copyir.ocm Turn off and then on the main power copyir.ocm
E070-00xx There is an error in the detection of the ITB home position copyir.ocm xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The home position of the intermediate transfer belt is not detected within a specific period of time copyir.ocm The ITB HP sensor is faulty copyir.ocm Turn off the main power, and check the DC controller PCB and the ITB HP sensor; then, turn on the main power copyir.ocm
E070-01xx There is an error in the detection of the ITB home position copyir.ocm xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The period of time between when the home position of the intermediate transfer belt is detected and the next home position is detected is longer than specified copyir.ocm The presence of a tear may have caused the sensor to wrongly identify it as indicating the home position copyir.ocm Turn off the main power, and check the drive of the intermediate transfer belt; then, turn on the main power copyir.ocm
E070-02xx There is an error in the detection of the ITB home position copyir.ocm xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The period of time between when the home position of the intermediate transfer belt is detected and when the next home position is detected is shorter than specified copyir.ocm The intermediate transfer belt slips on the drive roller, causing a delay in the timing at which the home position is detected copyir.ocm Turn off the main power, and check the surface of the intermediate transfer belt for a tear; then, turn on the main power copyir.ocm
E070-03xx There is an error in the detection of the ITB home position copyir.ocm xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The detection of the home position of the intermediate transfer belt has failed once copyir.ocm ITB home position sensor B and ITB home position sensor A must occur alternately; however, the same state has been detected continuously copyir.ocm Turn off the main power, and check the DC controller PCB and the ITB HP sensor; then turn on the main power copyir.ocm
E073-0001 With the front door closed, the transfer drawer connector or the transfer frame drawer connector is not connected copyir.ocm
The result of detecting the feed unit indicates the absence of the unit copyir.ocm Turn off and then on the main power copyir.ocm
E077-0001 The home position of the secondary transfer roller (engagement) is not detected copyir.ocm
The HP sensor does not go on within 5 sec after the start of a HP search copyir.ocm Turn off and then on the main power copyir.ocm
E078-0001 The home position of the transfer belt cleaner unit (engagement) is not detected copyir.ocm
The HP sensor does not turn on within 5 sec after the start of a HP search copyir.ocm Turn off and then on the main power copyir.ocm
E079-0001 The home position of the outside heating roller is not detected copyir.ocm The outside heating roller home position sensor does not go off copyir.ocm
The HP sensor does not turn on within 5 sec after the start of an HP search copyir.ocm Turn off and then on the main power copyir.ocm
E079-0002 The home position of the outside heating roller is not detected copyir.ocm The outside heating roller home position sensor does not go off copyir.ocm
If there is an open circuit in the home position sensor of the outside heating roller home position sensor, the state of the sensor will be identified as being ON copyir.ocm An error will be identified if the sensor fails to go off when it is at a point where it must normally go on and the outside heating roller shift motor is driven copyir.ocm Turn off and then on the main power copyir.ocm
E100-0001 The BD is not detected copyir.ocm
The BD signal is not detected when the polygon scanner has been driven for a specific period of time copyir.ocm Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power copyir.ocm
E100-0002 The BD is not detected copyir.ocm
The BD signal is not detected white the polygon scanner is rotating stably copyir.ocm Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power copyir.ocm
E110-0001 There is a scanner motor error copyir.ocm
The FG signal is not detected within a specific period of time after the polygon scanner has been driven copyir.ocm Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power copyir.ocm
E110-0002 There is a scanner motor error copyir.ocm
The FG signal is not detected while the polygon scanner is rotating stably copyir.ocm Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power copyir.ocm
E110-0003 There is a scanner motor error copyir.ocm
The FG signal is not detected while the polygon scanner is rotating stably copyir.ocm Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power copyir.ocm
E197-0002 There is an error in the communication with the fixing feed PCB copyir.ocm
In the course of initializing communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously copyir.ocm Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power copyir.ocm
E197-0003 There is an error in the communication with the fixing feed PCB copyir.ocm
Following the end of initialization of the communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously copyir.ocm Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power copyir.ocm
E197-0004 There is an error in the communication with the fixing feed PCB copyir.ocm
At the start of drum initial multiple rotation, there is no signal indicating the start of 24V in the fixing assembly in the communication between the DC controller and the fixing/feeding unit copyir.ocm Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power copyir.ocm
E202-0001 There is an HP error copyir.ocm
An error is found during the forward trip of the HP search copyir.ocm The scanner HP sensor is faulty copyir.ocm The scanner motor is faulty copyir.ocm The reader controller is faulty copyir.ocm Check the harness connector for connection; then, as necessary, replace the faulty part copyir.ocm
E202-0002 There is an HP error copyir.ocm
An error is found during the return trip of the HP search copyir.ocm The scanner HP sensor is faulty copyir.ocm The scanner motor is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm Check the harness connector for connection; then, as necessary, replace the faulty part copyir.ocm
E225-0001 The lamp has blown copyir.ocm
The level of shading is lower than specified copyir.ocm Check the harness connector for connection copyir.ocm Check the scanning lamp (xenon), inverter, and reader controller PCB copyir.ocm
E227-0001 There is a power supply (24V) error copyir.ocm
At power-on, the 24V port is off copyir.ocm Check the power supply harness connector for connection; then, as necessary, replace the power supply copyir.ocm
E227-0002 There is a power supply (24V) error copyir.ocm
At the start of a job, the 24V port is off copyir.ocm Check the power supply harness connector for connection; then, as necessary, replace the power supply copyir.ocm
E227-0003 There is a power supply (24V) error copyir.ocm
At the end of a job, the 24V port is off copyir.ocm Check the power supply harness connector for connection; then, as necessary, replace the power supply copyir.ocm
E227-0004 There is a power supply (24V) error copyir.ocm
While a load is being driven, the 24V port is off copyir.ocm Check the power supply harness connector for connection; then, as necessary, replace the power supply copyir.ocm
E240-0000 There is a DDI-P communication error copyir.ocm
There is a DDI-P communication error (error in communication between master and slave 0) copyir.ocm Turn off the main power, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main power copyir.ocm
E246-0001 An error has occurred in the course of writing to the counter memory copyir.ocm
Normal access to the FRAM PCB is not possible copyir.ocm A value is written to a specific area for a check on connection to the FRAM PCB; when read back, however, it is not the value that has been written copyir.ocm Turn off the main power, and check the connection of the counter PCB copyir.ocm If the remedy fails, replace the counter PCB copyir.ocm
E246-0002 An error has occurred in the course of writing to the counter memory copyir.ocm
When the soft ID of FRAM is being repaired, FRAM is not in an initialized condition copyir.ocm Replace the counter PCB copyir.ocm
E246-0003 An error has occurred in the course of writing to the counter memory copyir.ocm
After an increase in the count, data is read into FRAM; when it is read back and compared, it is not the value that has been read into FRAM copyir.ocm Replace the counter PCB copyir.ocm
E246-0004 An error has occurred in the course of writing to the counter memory copyir.ocm
A second after repair (from SRAM to FRAM) brings out different SRAM and FRAM counter readings copyir.ocm An attempt at repair has failed copyir.ocm Turn off the main power, and check the connector of the counter PCB copyir.ocm If repair fails, replace the counter PCB copyir.ocm
E247-0001 Error in counter memory or SRAM
An error exists in the SRAM and FRAM counter readings Replace the counter PCB or SRAM
E248-0000 There is an error in the EEPROM copyir.ocm
At time of start-up, a check error has occurred on the SRAM board Turn off the main power, and check the SRAM board; then, as necessary, replace the SRAM board, and turn on the main power copyir.ocm
E248-0001 There is an error in the EEPROM copyir.ocm
There is a power-on error copyir.ocm Replace the reader controller PCB copyir.ocm
E248-0002 There is an error in the EEPROM copyir.ocm
There is a write error copyir.ocm Replace the reader controller PCB copyir.ocm
E248-0003 There is an error in the EEPROM copyir.ocm
There is a wire/read error copyir.ocm Replace the reader controller PCB copyir.ocm
E315-000E codex error
An error has occurred in the course of software decoding copyir.ocm
E350-0000 Fault in the soft ID PCB/function
An error exists in the add-on parity copyir.ocm Reset in service mode, and replace the soft ID PCB copyir.ocm
E350-0001 Fault in the soft ID PCB/function
An error has occurred in the course of full data read operation on the soft ID PCB copyir.ocm Turn off the main power, and check the connection of the soft ID PCB copyir.ocm If the remedy fails, replace the soft ID PCB copyir.ocm
E350-0002 Fault in the soft ID PCB/function
The value of the check sum area of all data read from the soft ID PCB and the result of checksum computation do not match copyir.ocm Turn off the main power, and replace the soft ID PCB copyir.ocm If the remedy fails, replace the soft ID PCB copyir.ocm
E350-0003 Fault in the soft ID PCB/function
The values in the soft ID check sum area of FRAM, SRAM1, and SRAM2 and the result of a check sum computation differ copyir.ocm Turn off the main power, and check the connection of the soft ID PCB copyir.ocm If the remedy fails, replace the soft ID PCB copyir.ocm
E350-3000 Fault in the soft ID PCB/function
While an E350 error is backed up, the value of the check sum area of all data read from the soft ID PCB and the result of check sum computation do not match copyir.ocm Turn off the main power, and check the connection of the soft ID PCB copyir.ocm If the remedy fails, replace the soft ID PCB copyir.ocm
E351-0000 There is an error in the main controller PCB (sub) copyir.ocm
At start-up, there is an error in the communication between main controller PCB (sub) and the main controller PCB (main) copyir.ocm Turn off the main power, and replace the main controller PCB (sub) copyir.ocm If the result is not good, replace the main controller PCB (main), and turn on the main power copyir.ocm
E354-0001 Serial No copyir.ocm mismatch
All the values of the soft ID 8 digits of SEEPROM are 0x00 or 0xoff copyir.ocm Replace the soft ID PCB copyir.ocm
E354-0002 Serial No copyir.ocm mismatch
In the absence of an error, the soft ID PCB has been replaced with a new PCB and, in addition, the following conditions exist at the same time: – the soft IDs of the following pairs are not identical: SEEPROM and SRAM1, SEEPROM and SRAM2, SEEPROM and FRAM copyir.ocm – FRAM is not of the initialization pattern (i copyir.ocme copyir.ocm, the value of the check sum area is ‘1’ but the result of computation of the counter area check sum is not ‘1’) copyir.ocm – the soft IDs of the following are all identical: SRAM1, SRAM2, SRAM copyir.ocm A mistake is likely to have been made in the course of counter PCB replacement; as a result, E355 is likely to have occurred thereafter, not permitting recovery despite an attempt to reset E355 copyir.ocm
E355-0001 Serial No copyir.ocm mismatch PCB copyir.ocm
The soft IDs of the following pairs are not identical and, in addition, any of the following conditions exist: SEEPROM and SRAM1, SEEPROM and SRAM2, SEEPROM and FRAM copyir.ocm – FRAM is of the initialization pattern (i copyir.ocme copyir.ocm, the value of the check sum area is ‘1’, and the result of check sum computation of the counter area is ‘1’) copyir.ocm – the soft ID of any of the following is not identical: SRAM1, SRAM2, FRAM copyir.ocm Reset E355 (if the error occurs in the middle of repair operation) copyir.ocm At times, E355 cannot be reset (intentionally designed in such a way to prevent illegal replacement in the field) copyir.ocm
E400-0001 There is a DF communication error copyir.ocm
There is a check sum error copyir.ocm Disconnect and connect the harness connector; then, replace the reader controller PCB or the ADF DC controller copyir.ocm
E400-0002 There is a DF communication error copyir.ocm
There is a reception status error copyir.ocm Disconnect and connect the harness connector; then, replace the reader controller PCB or the ADF DC controller copyir.ocm
E400-0003 There is a DF communication error copyir.ocm
There is a reception interrupt error copyir.ocm Disconnect and connect the harness connector; then, replace the reader controller PCB or the ADF DC controller copyir.ocm
E413-0001 There is an error in the DF shift motor copyir.ocm
The shift HP sensor is open copyir.ocm Check the harness; then, as necessary, replace the sensor and motor copyir.ocm Check the attaching of the parts around the cam copyir.ocm
E413-0002 There is an error in the DF shift motor copyir.ocm
The shift HP sensor is closed copyir.ocm Check the harness; then, as necessary, replace the sensor and motor copyir.ocm Check the attaching of the parts around the cam copyir.ocm
E490-0001 The DF is of the wrong model copyir.ocm
The installed DF is not of the correct type copyir.ocm Replace the DF with one of an appropriate type copyir.ocm
E500-0001 There is a finisher communication error copyir.ocm
There is an error in data communication copyir.ocm An error has been detected in terms of the number of errors or the duration of the error in the communication between copier and finisher copyir.ocm Turn off the main power, and check the DC controller, wiring of the finisher PCB, and 24V system fuse; then, turn on the main power copyir.ocm
E503-0002 There is an error in the communication within the finisher (finisher R1/R2) copyir.ocm
There is a data communication error copyir.ocm finisher-to-saddle unit communication error Check the connection between the saddle stitcher controller PCB and the finisher controller PCB copyir.ocm
E503-0003 There is an error in the communication within the finisher (finisher R1/R2) copyir.ocm
finisher-to-punch unit communication error Check the connection between the Punch controller PCB and the finisher controller PCB copyir.ocm
E505-0001 There is an error in the backup memory of the finisher (finer R1/R2) copyir.ocm
There is an error in the data stored in the backup memory Turn off the main power, and check the DC control, wiring of the finisher PCB, and 24V system fuse; then, turn on the main power copyir.ocm
E505-0002 There is an error in the backup memory of the finisher (finer R1/R2) copyir.ocm
There is a data error in the punch assembly EEPROM copyir.ocm Turn off the main power, and check the wiring of the DC controller PCB and the puncher controller PCB: then, check the 24V system fuse, and turn back on the main power copyir.ocm
E514-8001 There is an error in the trailing edge assist motor (finisher R1/R2) copyir.ocm
The home position sensor does not go off when the trailing edge assist motor has been rotated for a specific period of time copyir.ocm 1) Check the trailing edge assist home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the trailing edge assist motor copyir.ocm Is the wiring normal? 3) Check the trailing edge assist mechanism copyir.ocm Is there a fault? 4) Try replacing the trailing edge assist motor copyir.ocm Is the problem corrected?
E514-8002 There is an error in the trailing edge assist motor (finisher R1/R2) copyir.ocm
The home position sensor does not go on when the trailing edge assist motor has been rotated for a specific period of time copyir.ocm 1) Check the trailing edge assist home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the trailing edge assist motor copyir.ocm Is the wiring normal? 3) Check the trailing edge assist mechanism copyir.ocm Is there a fault? 4) Try replacing the trailing edge assist motor copyir.ocm Is the problem corrected?
E519-0002 There is an error in the gear change motor (finisher R1/R2) copyir.ocm
The home position sensor does not go on within a specific period of time after the gear change motor has started to rotate copyir.ocm 1) Check the gear change home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor copyir.ocm Is the wiring normal? 3) Check the gear change mechanism copyir.ocm Is there a fault? 4) Try replacing the gear change motor copyir.ocm Is the problem corrected?
E519-8001 There is an error in the gear change motor (finisher R1/R2) copyir.ocm
The home position sensor does not go off within a specific period of time after the gear change motor has started to rotate copyir.ocm 1) Check the gear change home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor copyir.ocm Is the wiring normal? 3) Check the gear change mechanism copyir.ocm Is there a fault? 4) Try replacing the gear change motor copyir.ocm Is the problem corrected?
E530-8001 There is an error in front alignment (finisher R1/R2) copyir.ocm
Th alignment motor has started to rotate copyir.ocme home position sensor does not go off within a specific period of time after the front 1) Check the pre-aligning plate home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the pre-aligning plate motor copyir.ocm Is the wiring normal? 3) Check the path of the aligning plate copyir.ocm Is there a mechanical obstacle? 4) Try replacing the pre-aligning plate motor copyir.ocm Is the problem corrected?
E530-8002 There is an error in front alignment (finisher R1/R2) copyir.ocm
The home position sensor does not go on within a specific period of time after the front alignment motor has started to rotate copyir.ocm 1) Check the pre-aligning plate home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the pre-aligning plate motor copyir.ocm Is the wiring normal? 3) Check the path of the aligning plate copyir.ocm Is there a mechanical obstacle? 4) Try replacing the pre-aligning plate motor copyir.ocm Is the problem corrected?
E531-0001 There is an error in stapling (finisher R1/R2) copyir.ocm
The home position sensor does not go off within a specific period of time after the stapler motor has started to rotate copyir.ocm 1) Check the wiring between the finisher controller PCB and the stapler copyir.ocm Is the wiring normal? 2) Try replacing the stapler copyir.ocm Is the problem corrected?
E531-0002 There is an error in stapling (finisher R1/R2) copyir.ocm
The home position sensor does not go on within a specific period of time after the stapler motor has started to rotate 1) Check the wiring between the finisher controller PCB and the stapler copyir.ocm Is the wiring normal? 2) Try replacing the stapler copyir.ocm Is the problem corrected?
E532-8001 There is an error in the shift mechanism of the stapler copyir.ocm (finisher R1/R2)
The home position sensor does not go off within a specific period of time after the stapler shift motor has started to rotate copyir.ocm 1) Check the stapler shift home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor copyir.ocm Is the wiring normal? 3) Check the path of the stapler shift base copyir.ocm Is there a mechanical obstacle? 4) Try replacing the stapler shift motor copyir.ocm Is the problem corrected?
E532-8002 There is an error in the shift mechanism of the stapler copyir.ocm (finisher R1/R2)
The home position sensor does not go on within a specific period of time after the stapler shift motor has started to rotate copyir.ocm 1) Check the stapler shift home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor copyir.ocm Is the wiring normal? 3) Check the path of the stapler shift base copyir.ocm Is there a mechanical obstacle? 4) Try replacing the stapler shift motor copyir.ocm Is the problem corrected?
E535-0003 There is an error in the staple swing mechanism copyir.ocm (finisher R1/R2)
There is an error in relation to an hazardous area copyir.ocm copyir.ocm 1) Check the swing home position sensor copyir.ocm Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor copyir.ocm Is the wiring normal? 3) Check the swing mechanism copyir.ocm Is there a fault? 4) Try replacing the swing motor copyir.ocm Is the problem corrected?
E535-8001 There is an error in the staple swing mechanism copyir.ocm (finisher R1/R2)
The home position sensor does not go off even when the swing motor has rotated for a specific period of time copyir.ocm 1) Check the swing home position sensor copyir.ocm Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor copyir.ocm Is the wiring normal? 3) Check the swing mechanism copyir.ocm Is there a fault? 4) Try replacing the swing motor copyir.ocm Is the problem corrected?
E535-8002 There is an error in the staple swing mechanism copyir.ocm (finisher R1/R2)
The home position sensor does not go on even when the swing motor has rotated for a specific period of time copyir.ocm 1) Check the swing home position sensor copyir.ocm Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor copyir.ocm Is the wiring normal? 3) Check the swing mechanism copyir.ocm Is there a fault? 4) Try replacing the swing motor copyir.ocm Is the problem corrected?
E537-8001 rear alignment error (Finisher-R1/R2)
The home position sensor does not go off even when the swing motor has rotated for a specific period of time copyir.ocm 1) Check the post-aligning plate home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the post-aligning plate motor copyir.ocm Is the wiring normal? 3) Check the path of the aligning plate copyir.ocm Is there a mechanical obstacle? 4) Try replacing the post-aligning plate motor copyir.ocm Is the problem corrected?
E537-8002 rear alignment error (Finisher-R1/R2)
The home position sensor does not go on even when the swing motor has rotated for a specific period of time copyir.ocm 1) Check the post-aligning plate home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the post-aligning plate motor copyir.ocm Is the wiring normal? 3) Check the path of the aligning plate copyir.ocm Is there a mechanical obstacle? 4) Try replacing the post-aligning plate motor copyir.ocm Is the problem corrected?
E540-8001 upper tray ascent/descent error (Finisher-R1/R2)
upper tray ascent/descent motor clock error 1) Check the No copyir.ocm 1 tray area sensors 1 through 3 copyir.ocm Are the sensors normal? 2) Check the wiring between finisher controller PCB and the No copyir.ocm 1 tray shift motor copyir.ocm Is the wiring normal? 3) Is there a fault in the ascent/descent mechanism of the tray? 4) Try replacing the No copyir.ocm 1 tray shift motor copyir.ocm Is the problem corrected?
E540-8002 upper tray ascent/descent error (Finisher-R1/R2)
area error 1) Check the No copyir.ocm 1 tray area sensors 1 through 3 copyir.ocm Are the sensors normal? 2) Check the wiring between finisher controller PCB and the No copyir.ocm 1 tray shift motor copyir.ocm Is the wiring normal? 3) Is there a fault in the ascent/descent mechanism of the tray? 4) Try replacing the No copyir.ocm 1 tray shift motor copyir.ocm Is the problem corrected?
E540-8003 upper tray ascent/descent error (Finisher-R1/R2)
safety switch activation 1) Check the No copyir.ocm 1 tray area sensors 1 through 3 copyir.ocm Are the sensors normal? 2) Check the wiring between finisher controller PCB and the No copyir.ocm 1 tray shift motor copyir.ocm Is the wiring normal? 3) Is there a fault in the ascent/descent mechanism of the tray? 4) Try replacing the No copyir.ocm 1 tray shift motor copyir.ocm Is the problem corrected?
E542-0003 lower tray ascent/descent error (Finisher-R1/R2)
safety switch activation 1) Check the No copyir.ocm 2 tray sensors 1 through 3 copyir.ocm Are the sensors normal? 2) Check the wiring between the finer controller PCB and the No copyir.ocm 2 tray shift motor copyir.ocm Is the wiring normal? 3) Is there a fault in the tray ascent/descent mechanism? 4) Try replacing the No copyir.ocm 2 tray shift motor copyir.ocm Is the problem corrected?
E542-8001 lower tray ascent/descent error (Finisher-R1/R2)
lower tray ascent/descent motor clock error 1) Check the No copyir.ocm 2 tray sensors 1 through 3 copyir.ocm Are the sensors normal? 2) Check the wiring between the finer controller PCB and the No copyir.ocm 2 tray shift motor copyir.ocm Is the wiring normal? 3) Is there a fault in the tray ascent/descent mechanism? 4) Try replacing the No copyir.ocm 2 tray shift motor copyir.ocm Is the problem corrected?
E542-8002 lower tray ascent/descent error (Finisher-R1/R2)
area error 1) Check the No copyir.ocm 2 tray sensors 1 through 3 copyir.ocm Are the sensors normal? 2) Check the wiring between the finer controller PCB and the No copyir.ocm 2 tray shift motor copyir.ocm Is the wiring normal? 3) Is there a fault in the tray ascent/descent mechanism? 4) Try replacing the No copyir.ocm 2 tray shift motor copyir.ocm Is the problem corrected?
E584-0002 shutter unit error (Finisher-R1/R2)
The shutter open/closed sensor does not go on (i copyir.ocme copyir.ocm, the shutter does not open) copyir.ocm 1) Check the shutter home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stack edging motor and between the finisher controller PCB and the shutter open/close clutch copyir.ocm Is the wiring normal? 3) Is there a fault in the shutter mechanism? 4) Try replacing the stack edging motor or the shutter open/close clutch copyir.ocm Is the problem corrected?
E584-8001 shutter unit error (Finisher-R1/R2)
The shutter open sensor does not go off (i copyir.ocme copyir.ocm, the shutter is not closed) copyir.ocm 1) Check the shutter home position sensor copyir.ocm Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stack edging motor and between the finisher controller PCB and the shutter open/close clutch copyir.ocm Is the wiring normal? 3) Is there a fault in the shutter mechanism? 4) Try replacing the stack edging motor or the shutter open/close clutch copyir.ocm Is the problem corrected?
E590-8001 There is an error in the punch motor copyir.ocm (punch unit)
The punching home position sensor is not detected when the punch motor has been driven for 200 msec copyir.ocm Check the punch home position sensor, horizontal registration motor, and punch driver PCB; then, turn off and then on the main power copyir.ocm
E590-8002 There is an error in the punch motor copyir.ocm (punch unit)
The puncher does not detect the punching home position after the motor has stopped (initial operation) copyir.ocm Check the punch home position sensor, horizontal registration motor, and punch driver PCB; then, turn off and then on the main power copyir.ocm
E591-8001 There is an error in the punch dust sensor copyir.ocm (punch unit)
There is an error in the light copyir.ocm Turn off and then on the main power copyir.ocm
E591-8002 There is an error in the punch dust sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage without emission of light copyir.ocm Turn off and then on the main power copyir.ocm
E592-8001 There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage at time of light emission copyir.ocm (trailing edge sensor) Turn off and then on the main power copyir.ocm
E592-8002 There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage without emission of light copyir.ocm (trailing edge sensor) Turn off and then on the main power copyir.ocm
E592-8003 There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage with emission of light copyir.ocm (horizontal registration sensor 1) Turn off and then on the main power copyir.ocm
E592-8004 There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage without emission of light copyir.ocm (horizontal registration sensor 1) Turn off and then on the main power copyir.ocm
E592-8005 There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage with emission of light copyir.ocm (horizontal registration sensor 2) Turn off and then on the main power copyir.ocm
E592-8006 There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage without emission of light copyir.ocm (horizontal registration sensor 2) Turn off and then on the main power copyir.ocm
E592-8007 There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage it the presence of emission of light copyir.ocm (horizontal registration sensor 3) Turn off and then on the main power copyir.ocm
E592-8008 There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage without emission of light copyir.ocm (horizontal registration sensor 3) Turn off and then on the main power copyir.ocm
E592-8009 There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage with emission of light copyir.ocm (horizontal registration sensor 4) Turn off and then on the main power copyir.ocm
E592-800A There is an error in the punch horizontal registration sensor copyir.ocm (punch unit)
There is an error in the light-receiving voltage without emission of light copyir.ocm (horizontal registration sensor 4) Turn off and then on the main power copyir.ocm
E593-8001 There is an error in the punch shift motor copyir.ocm (punch unit)
The light-receiving voltage HP sensor does not go off at time of light emission copyir.ocm Turn off and then on the main power copyir.ocm
E593-8002 There is an error in the punch shift motor copyir.ocm (punch unit)
The light-receiving voltage HP sensor doest not go on without emission of light copyir.ocm Turn off and then on the main power copyir.ocm
E5F0-0001 There is an error in saddle paper positioning copyir.ocm
The paper positioning plate home position sensor does not turn on when the paper positioning plate motor has been driven for 1 copyir.ocm33 sec copyir.ocm The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty copyir.ocm Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S) copyir.ocm
E5F0-0002 There is an error in saddle paper positioning copyir.ocm
The paper positioning plate home position sensor does not turn off when the paper positioning plate motor has been driven for 1 sec copyir.ocm The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty copyir.ocm Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S) copyir.ocm
E5F1-0001 There is an error in saddle paper folding copyir.ocm
The number of detection pulses of the paper folding motor clock sensor is lower than specified copyir.ocm The paper folding home position sensor or the paper folding motor clock sensor (P14S) is faulty copyir.ocm Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S) copyir.ocm
E5F1-0002 There is an error in saddle paper folding copyir.ocm
The state of the paper folding home position sensor does not change when the paper folding motor has been driven for 3 sec copyir.ocm The paper folding motor (M2S) or the paper folding motor clock sensor (P14S) is faulty copyir.ocm Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S) copyir.ocm
E5F2-0001 There is an error in the saddle guide copyir.ocm
The guide home position sensor does not turn on when the guide motor has been driven for 0 copyir.ocm45 sec copyir.ocm The guide motor (M3S) or the guide home position sensor (PI3S) is faulty copyir.ocm Check the guide motor (M3S) /guide home position sensor (PI13S) copyir.ocm
E5F2-0002 There is an error in the saddle guide copyir.ocm
The guide home position sensor doest not turn off when the guide motor has been driven for 1 sec copyir.ocm The guide motor (M3S) or the guide home position sensor (PI3S) is faulty copyir.ocm Check the guide motor (M3S) /guide home position sensor (PI13S) copyir.ocm
E5F3-0001 There is an error in saddle alignment copyir.ocm
The aligning plate home position sensors does not turn on when the alignment motor has been driven for 05 copyir.ocm sec (during initialization, 1 copyir.ocm67 sec) copyir.ocm The alignment motor (M5S) or the aligning plate home position sensor (PI5S) is faulty copyir.ocm Check the alignment motor (M5S) /aligning plate home position sensor (PI5S) copyir.ocm
E5F3-0002 There is an error in saddle alignment copyir.ocm
The alignment plate home position sensor does not turn off when the alignment motor has been driven for 1 sec copyir.ocm The alignment motor (M5S) for the alignment plate home position sensor (PI5S) is faulty copyir.ocm Check the alignment motor (M5S) /aligning plate home position sensor (PI5S) copyir.ocm
E5F4-0001 There is an error in saddle rear sampling copyir.ocm
The stitching home position sensor does not turn on when the stapler motor (rear) is rotated in reverse for 0 copyir.ocm5 sec or more copyir.ocm The switch motor (rear, M65) or the stitching home position sensor (rear, MS5S) is faulty copyir.ocm Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S)
E5F4-0002 There is an error in saddle rear sampling copyir.ocm
The stitching home position sensor does not turn off when the switch motor (rear) is reverse for 0 copyir.ocm5 sec or more copyir.ocm The switch motor (rear, M6S) or the stitching home position sensor (rear, MS5S) is faulty copyir.ocm Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S) copyir.ocm
E5F5-0001 There is an error in saddle front stapling copyir.ocm
The stitching home position sensor does not turn on when the switch motor (front) is rotated in reverse for 0 copyir.ocm5 sec or more copyir.ocm The stitch motor (front, M7S) or the stitching home position sensor (front, MS7S) is faulty copyir.ocm Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S) copyir.ocm
E5F5-0002 There is an error in saddle front stapling copyir.ocm
The stitching home position sensor does not turn off when the switch motor (front) is rotated in normal direction for 0 copyir.ocm5 copyir.ocm The stitch motor (front, M7S) or the switching home position sensor (front, MS7S) is faulty copyir.ocm Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S) copyir.ocm
E5F6-8001 There is an error in saddle butting copyir.ocm
The paper pushing plate home position sensor does not turn on when the paper pushing motor has been driven for 0 copyir.ocm3 sec or more copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4) is faulty copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4) is faulty copyir.ocm
E5F6-8002 There is an error in saddle butting copyir.ocm
The paper pushing plate home position sensor does not turn off when paper pushing plate motor has been driven for 80 msec or more copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4S) is faulty copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4S) is faulty copyir.ocm
E5F6-8003 There is an error in saddle butting copyir.ocm
The number of detection pulses of the paper pushing plate motor clock sensor drops below a specific number copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate motor clock sensor (PI1S) is faulty copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate motor clock sensor (PI1S) is faulty copyir.ocm
E5F6-8004 There is an error in saddle butting copyir.ocm
The paper pushing plate sensor does not turn off when the paper pushing plate motor has been driven for 80 msec or more copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty copyir.ocm
E5F6-8005 There is an error in saddle butting copyir.ocm
The paper pushing plate leading edge position sensor does not turn on when the paper pushing plate motor has been driven for 0 copyir.ocm3 sec or more copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI5S) is faulty copyir.ocm The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI5S) is faulty copyir.ocm
E5F8-0001 There is an error in the saddle connector copyir.ocm
The connector of the guide home position sensor is identified as being disconnected copyir.ocm The connector of the guide home position sensor (PI3S) is faulty copyir.ocm Check the connectors of the guide home position sensor (PI13S) copyir.ocm Check the connectors of the paper pushing plate home position sensor (PI4S) copyir.ocm
E5F8-0002 There is an error in the saddle connector copyir.ocm
The connector of the paper pushing plate home position sensor is identified as being disconnected copyir.ocm The connector of the paper pushing plate home position sensor (PI14S) is faulty copyir.ocm Check the connectors of the paper pushing plate leading edge position sensor (PI5S) copyir.ocm
E5F8-0003 There is an error in the saddle connector copyir.ocm
The connector of the paper pushing plate leading edge position sensor is identified as being disconnected copyir.ocm The connector of the paper pushing plate leading edge sensor (PI15S) is faulty copyir.ocm Check the connectors of the paper pushing plate leading edge position sensor (PI5S) copyir.ocm
E5F9-0001 There is an error in the saddle switch copyir.ocm
With any of the following sensor is identifying its respective cover a being closed, the inlet cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: – inlet cover sensor (PI9S) – front cover open/closed sensor (PI2S) – delivery cover sensor (PI3S) Or, the front cover switch (MS2S) or the delivery cover switch (MS3S) is open copyir.ocm The inlet cover switch (MS1S), front cover switch (MS2S), or delivery cover switch (MS3S) is faulty copyir.ocm Check the inlet cover switch (MS1S)/front cover switch (MS2S)/delivery cover switch (MS3S) copyir.ocm
E5F9-0002 There is an error in the saddle switch copyir.ocm
With any of the following sensor is identifying its respective cover as being closed, the front cove switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: – inlet cover sensor (PI9S) – front cover open/closed sensor (PI2S) – delivery cove sensor (PI3S) The front cove switch (MS2S) or the delivery cover switch (MS3S) is faulty copyir.ocm Check the front cover switch (MS2S)/delivery cover switch (MS3S) copyir.ocm
E5F9-0003 There is an error in the saddle switch copyir.ocm
With any of the following sensors identifying its respective cover as being closed, the delivery cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: – inlet cover sensor (PI9S) – front cover open/closed sensor (PI2S) – delivery cover sensor (PI3S) – delivery cover switch (MS3S) Check the delivery cover switch (MS3S) copyir.ocm
E602 There is a hard disk error copyir.ocm
E604-0000 There is a shortage of image memory (SDRAM) copyir.ocm
The amount of memory required by the model in question is not recognized copyir.ocm Set it to the size of memory suited to the model in question copyir.ocm
E609-0008 Samsung HDD-related error code
The HDD does not increase to a specific temperature level within a specific time when the power is turned on copyir.ocm Replace the HDD copyir.ocm
E609-0009 Samsung HDD-related error code
The HDD does not increase to a specific temperature level in relation to a sleep state copyir.ocm Turn off and then on the power copyir.ocm If the return operation fails, replace the HDD copyir.ocm
E610 HDD encryption key fault
E674-0001 There is an error in the fax board copyir.ocm
The fax board is detected, but communication is not possible copyir.ocm Turn off the main power, and check the fax board and the main controller PCB; then, turn on the main power copyir.ocm If the machine fails to reset, replaced the fax board or the main controller PCB
E677-0003 There is an external controller error copyir.ocm
An error has been detected by a check on the configuration when the external controller is being started up copyir.ocm Turn off the main power, and check the cable; then, turn on the main power copyir.ocm If the machine fails to start up, re-install the system software of the external contro
E677-0010 There is an external controller error copyir.ocm
A controller for a non-Canon machine is connected copyir.ocm Turn off the main power, and check the controller is an appropriate type, and check the cable; then turn on the main power copyir.ocm If the machine fails to reset, re-install the system software of the external controller copyir.ocm
E677-0080 There is an external controller error copyir.ocm
There is an error in the communication with the printer after the external controller has started up normally copyir.ocm Turn off the main power, and check the cable; then, turn on the main power copyir.ocm If the machine fails to start up, re-install the system software of the external controller copyir.ocm
E710-0001 There is an error in IPC initialization copyir.ocm
The machine fails to become ready within 3 sec after the IPC chip has started up copyir.ocm Turn off the main power, and check the cable; then, turn on the main power copyir.ocmted up copyir.ocm
E711-0002 There is an IPC communication error copyir.ocm
An error has been detected 4 times or more within 1 copyir.ocm5 sec after the communication has been interrupted between the finisher and the printer, and the machine does not reset copyir.ocm Turn off the main power, and check the cable; then, turn on the main power copyir.ocm If the machine fails to reset, check the connector between the finisher and the copier for poor contact; as necessary, replace the finisher controller/DC controller copyir.ocm
E713-0001 There is a finisher communication error copyir.ocm
There is an error in the IC used for communication by the sorter copyir.ocm Turn off the main power switch, and check the wiring of the DC controller PCB and the finisher controller PCB, and check the 24V system fuse: then, turn on the main power switch copyir.ocm If the machine does not reset, replace the DC controller PCB/finisher controller PCB copyir.ocm
E717-0001 There is an error in the communication with the NE controller copyir.ocm
The NE controller that was connected before the power is turned off is not recognized after the power is turned on copyir.ocm Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E717-0002 There is an error in the communication with the NE controller copyir.ocm
An IPC open circuit or an IPC communication error is not reset copyir.ocm Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E719-0001 error in communication with coin vendor/card reader
The coin vendor that is connected before the power is turned off is not recognized when the paper is turned on copyir.ocm Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E719-0002 error in communication with coin vendor/card reader
– The IPC cable to the coin vendor is broken and the IPC communication cannot be recovered copyir.ocm – There is an open circuit in the pickup delivery signal line copyir.ocm – An improper connection is detected (short circuit between Tx and Rx of IPC) copyir.ocm Check the cable; thereafter, reset by making the following selections: COPIER>FUNCTION>CLEAR>ERROR
E719-0011 error in communication with coin vendor/card reader
The card reader that is connected before the power is turned off is not recognized when the paper is turned on copyir.ocm Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E719-0012 error in communication with coin vendor/card reader
There is an IPC cable open circuit or an IPC communication error in relation to the card reader that cannot be reset copyir.ocm Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR copyir.ocm
E730 There is a PDL error copyir.ocm
E731 There is a UFR board error copyir.ocm Turn off the main power, and check the connection of the UFR board; then, turn on the main power copyir.ocm If the machine does not reset, replace the UFR board or the main controller PCB copyir.ocm
E732-0001 There is an error in reader communication copyir.ocm
There is an error in reader communication copyir.ocm Turn off the main power, and check the connectors to the reader, and check the power supply of the reader; then, turn on the main power copyir.ocm
E732-9999 There is an error in reader communication copyir.ocm
Although a printer model, the machine is identified as a reader unit at start-up copyir.ocm (A copier model is started up as a printer model when the RAM is initialized copyir.ocm) Turn off and then on the main power copyir.ocm
E733-0000 There is a printer communication error copyir.ocm
There is a printer communication error copyir.ocm At start-up, the printer is not detected copyir.ocm Turn off the main power, and check the connectors to the DC controller PCB and the main controller PCB, and check the power supply of the printer; then, turn on the main power copyir.ocm
E733-0001 There is a printer communication error copyir.ocm
There is a DDI-P communication error copyir.ocm Turn off the main power, and check the connectors to the DC control PCB and the main controller PCB, and check the power supply of the printer; then, turn on the main power copyir.ocm
E740-0002 There is an Ethernet board error copyir.ocm
At time of start-up, the MAC address is found to be illegal copyir.ocm A non-Canon MAC address is detected copyir.ocm Turn off the main power, and replace the NIC; then, turn on the main power
E743-0000 There is a DDI communication error copyir.ocm
There is an SCI error copyir.ocm The reception data is faulty copyir.ocm A reception time-out condition has occurred copyir.ocm An SEQ timeout error has occurred copyir.ocm An SEQ time-out error has occurred copyir.ocm Disconnect and connect the DDI-S cable connector; then, as necessary, replace the reader controller PCB or the main controller PCB copyir.ocm
E744 There is a language file/boot ROM error copyir.ocm Download the appropriate language fields of the correct version using the Service Support Tool
E745 There is a TokenRing error copyir.ocm
E746-0003 The accessories board is of the wrong type copyir.ocm
At time of start-up, the UFR board is found to be of the wrong type copyir.ocm (A query is made to find out if the type is correct with reference to the engine ID copyir.ocm) Replace it with a UFR board of the correct type copyir.ocm
E746-0004 The accessories board is of the wrong type copyir.ocm
At time of start-up, the scanner board is found to be of the wrong type copyir.ocm (A query is made to find out if the type is correct with reference to the engine ID copyir.ocm) Replace it with a scanner board of the correct type copyir.ocm
E747 There is an error in the ASIC for image processing or in the ASIC for memory control/communication control copyir.ocm
There is an error in IC1015 (ASIC for image processing) or in IC1012 (for memory control/communication control) on the main controller PCB copyir.ocm (e copyir.ocmg copyir.ocm, image data transfer error) Turn off the main power, and check the main controller PCB; then, turn on the main controller PCB
E748 CL2 board-dependent board error 1 copyir.ocm Disconnect and then connect 4 to 5 G-chip boards several times copyir.ocm 2 copyir.ocm Replace the G-chip board copyir.ocm 3 copyir.ocm Replace the main controller PCB copyir.ocm
E749-0001 Reboot instruction initiated by change in PDL configuration
A change has occurred that calls for turning off and then on the power copyir.ocm Turn off and then on the power copyir.ocm
E800-0001 The interlock 24V mechanism of the fixing unit is identified as being off copyir.ocm With the door closed, the interlock 24V mechanism remains off for 500 msec copyir.ocm Turn off the main switch, and check the wiring of the DC controller PCB, check the fixing unit interlock, and check the 24V system fuse; then, turn on the interlock main switch copyir.ocm
E804-0004 There is any of the various types of fan errors copyir.ocm
There is an error in the controller cooling fan copyir.ocm Turn off the main switch, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main switch copyir.ocm
E804-0007 There is any of the various types of fan errors copyir.ocm
There is an error in the power supply cooling fan copyir.ocm Turn off the main switch, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch copyir.ocm
E805-0003 The fixing heat exhaust fan is identified as having stopped or having an error copyir.ocm
There is an error in the fixing heat exhaust fan copyir.ocm Turn off the main power, and check the supply of power to the fan; then, as necessary, replace the fan, and turn on the main power copyir.ocm
E820-0002 There is an error in the process unit cooling fan copyir.ocm
There is an error in the process unit fan copyir.ocm Turn off the main switch, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main switch copyir.ocm
E824-0000 There is an error in the primary charging suction/primary charging exhaust fan copyir.ocm
There is an error in the primary charging suction mechanism copyir.ocm Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch copyir.ocm
E824-0001 There is an error in the primary charging suction/primary charging exhaust fan copyir.ocm
There is an error in the primary exhaust fan copyir.ocm Turn off the main switch, and check the wiring of the DC controller PCB and 2V system fuse; then, turn on the main switch copyir.ocm
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.