کدها و خطاهای فتوکپی ریکو آفیشیو 1105
TROUBLESHOOTING
7.1 SERVICE CALL CONDITIONS
7.1.1 SUMMARY
فتوکپی ریکو آفیشیو 1105re are 4 levels of service call conditions.
Level |
Definition |
Reset Procedure |
A |
To prevent فتوکپی ریکو آفیشیو 1105 machine from being damaged, فتوکپی ریکو آفیشیو 1105 SC can only be reset by a service representative (see فتوکپی ریکو آفیشیو 1105 note below).
فتوکپی ریکو آفیشیو 1105 copier cannot be operated at all. |
Enter SP mode, فتوکپی ریکو آفیشیو 1105n turn فتوکپی ریکو آفیشیو 1105 main power switch off and on. |
B |
فتوکپی ریکو آفیشیو 1105 SC can be reset by turning فتوکپی ریکو آفیشیو 1105 main power switch off and on if فتوکپی ریکو آفیشیو 1105 SC was caused by incorrect sensor detection. | Turn فتوکپی ریکو آفیشیو 1105 operation switch or main power switch off and on. A level B’ SC can only be reset by turning فتوکپی ریکو آفیشیو 1105 main power switch off and on. |
C |
فتوکپی ریکو آفیشیو 1105 copier can be operated as usual except for فتوکپی ریکو آفیشیو 1105 unit related to فتوکپی ریکو آفیشیو 1105 service call. | Turn فتوکپی ریکو آفیشیو 1105 operation switch off and on. |
D |
فتوکپی ریکو آفیشیو 1105 SC history is updated. فتوکپی ریکو آفیشیو 1105 machine can be operated as usual. | فتوکپی ریکو آفیشیو 1105 SC will not be displayed. All that happens is that فتوکپی ریکو آفیشیو 1105 SC history is updated. |
NOTE: 1) If فتوکپی ریکو آفیشیو 1105 problem concerns electrical circuit boards, first disconnect فتوکپی ریکو آفیشیو 1105n reconnect فتوکپی ریکو آفیشیو 1105 connectors before replacing فتوکپی ریکو آفیشیو 1105 PCBs.
2) If فتوکپی ریکو آفیشیو 1105 problem concerns a motor lock, first check فتوکپی ریکو آفیشیو 1105 mechanical load before replacing motors or sensors.
3) When a Level A or B SC occurs while in an SP mode, فتوکپی ریکو آفیشیو 1105 display does not indicate فتوکپی ریکو آفیشیو 1105 SC number. If this occurs, check فتوکپی ریکو آفیشیو 1105 SC number after leaving فتوکپی ریکو آفیشیو 1105 SP mode. This does not apply to Level B’ codes.
7.1.2 SC CODE DESCRIPTIONS
SC101: Exposure Lamp Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 standard white level was not detected properly when scanning فتوکپی ریکو آفیشیو 1105 white plate. Possible Causes
- Exposure lamp defective
- Lamp stabilizer defective
- Exposure lamp connector defective
- Dirty standard white plate
- Dirty scanner mirror or scanner mirror out of position
- SBU board defective
- SBU connector defective
- Lens block out of position
SC120: Scanner Home Position Error 1
Definition [B]
فتوکپی ریکو آفیشیو 1105 scanner home position sensor does not detect فتوکپی ریکو آفیشیو 1105 on condition during initialization or copying. Possible Causes
- Scanner home position sensor defective
- Scanner motor defective
- MCU defective
- Scanner home position sensor connector defective
- Scanner drive motor connector defective
SC121: Scanner Home Position Error 2
Definition [B]
فتوکپی ریکو آفیشیو 1105 scanner home position sensor does not detect فتوکپی ریکو آفیشیو 1105 off condition during initialization or copying. Possible Causes
- Scanner home position sensor defective
- Scanner drive motor defective
- MCU defective
- Scanner home position sensor connector defective
- Scanner drive motor connector defective
- Scanner drive wire, timing belt out of position
SC124: Scanner Motor Error 1
Definition [B]
فتوکپی ریکو آفیشیو 1105 feedback signal from فتوکپی ریکو آفیشیو 1105 scanner motor is not detected within 200 ms after فتوکپی ریکو آفیشیو 1105 scanner motor turns on. Possible Causes
- Scanner motor defective
- Poor connection of فتوکپی ریکو آفیشیو 1105 connector for فتوکپی ریکو آفیشیو 1105 feedback signal
- Poor connection of فتوکپی ریکو آفیشیو 1105 connector for فتوکپی ریکو آفیشیو 1105 scanner motor power line
SC125: Scanner Motor Error 2
Definition [B]
1) فتوکپی ریکو آفیشیو 1105 scanner motor speed is less than 300 mm/s when فتوکپی ریکو آفیشیو 1105 scanner home position sensor turns on.
2) فتوکپی ریکو آفیشیو 1105 scanner motor stops before scanner home position when فتوکپی ریکو آفیشیو 1105 scanner returns.
Possible Causes
- Scanner motor defective
- Large load on فتوکپی ریکو آفیشیو 1105 scanner drive
SC126: Scanner Motor Error 3
Definition [B]
فتوکپی ریکو آفیشیو 1105 scanner motor does not stop within 12 mm after فتوکپی ریکو آفیشیو 1105 scanner home position sensor turns on when فتوکپی ریکو آفیشیو 1105 scanner returns.
Possible Causes
- Scanner motor defective
- MCU defective
SC127: Scanner Motor Error 4
Definition [B]
فتوکپی ریکو آفیشیو 1105 scanner motor rotates in فتوکپی ریکو آفیشیو 1105 opposite direction from فتوکپی ریکو آفیشیو 1105 signal from فتوکپی ریکو آفیشیو 1105
MCU.
Possible Causes
- Scanner motor defective
SC128: Scanner Motor Error 5
Definition [B]
فتوکپی ریکو آفیشیو 1105 scanner motor speed does not reach فتوکپی ریکو آفیشیو 1105 target speed within a certain time after فتوکپی ریکو آفیشیو 1105 scanner motor starts.
Possible Causes
- Scanner motor defective
- MCU defective
- Scanner drive mechanism defective
SC129: Scanner Motor Error 6
Definition [B]
فتوکپی ریکو آفیشیو 1105 scanner motor speed is not controlled properly.
Possible Causes
- Scanner motor defective
- PSU defective
- Scanner unit defective
SC130: SBU Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 SICU does not receive فتوکپی ریکو آفیشیو 1105 correct signal from فتوکپی ریکو آفیشیو 1105 SBU.
Possible Causes
- SICU defective
- SBU defective
- Poor connection between SICU and SBU
SC300: Charge Corona Output Error 1
Definition [B]
A feedback voltage for فتوکپی ریکو آفیشیو 1105 charge corona of more than 4.5 V was detected from فتوکپی ریکو آفیشیو 1105 charge/bias/grid power pack 9 times consecutively.
Possible Causes
- Charge/bias/grid power pack defective
- Poor charge corona unit connection
SC301: Charge Corona Output Error 2
Definition [B]
A feedback voltage for فتوکپی ریکو آفیشیو 1105 charge corona of less than 1.5 V was detected from فتوکپی ریکو آفیشیو 1105 charge/bias/grid power pack 9 times consecutively.
Possible Causes
- Charge/bias/grid power pack defective
- Poor charge corona unit connection
SC303: Charge Grid Output Error 1
Definition [B]
A feedback voltage for فتوکپی ریکو آفیشیو 1105 grid of more than 4.5 V was detected from فتوکپی ریکو آفیشیو 1105 charge/bias/grid power pack 9 times consecutively.
Possible Causes
- Charge/bias/grid power pack defective
- Poor charge corona unit connection
SC304: Charge Grid Output Error 2
Definition [B]
A feedback voltage for فتوکپی ریکو آفیشیو 1105 grid of less than 1.0 V was detected from فتوکپی ریکو آفیشیو 1105 charge/bias/grid power pack 9 times consecutively.
Possible Causes
- Charge/bias/grid power pack defective
- Poor charge corona unit connection
SC305: Charge Corona Wire Cleaner Error 1
Definition [B]
فتوکپی ریکو آفیشیو 1105 charge corona wire cleaner does not return to its home position.
Possible Causes
- Charge corona wire cleaner motor defective
- BCU defective
SC306: Charge Corona Wire Cleaner Error 2
Definition [D]
فتوکپی ریکو آفیشیو 1105 charge corona wire cleaner motor connector is not connected. Possible Causes
- Poor connection or disconnected charge corona wire cleaner motor connector
SC310: Drum Potential Sensor Error 1
Definition [D]
When calibrating فتوکپی ریکو آفیشیو 1105 drum potential sensor during process control initial setting, فتوکپی ریکو آفیشیو 1105 drum potential sensor output voltage is out of specification.
Possible Causes
- Drum potential sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 drum potential sensor and فتوکپی ریکو آفیشیو 1105 BCU
- BCU defective
- Charge/bias/grid power pack defective
SC311: Drum Potential Sensor Error 2
Definition [D]
When calibrating فتوکپی ریکو آفیشیو 1105 drum potential sensor during process control initial setting, فتوکپی ریکو آفیشیو 1105 rate of change of drum potential sensor output with voltage on فتوکپی ریکو آفیشیو 1105 drum is out of specification.
Possible Causes
- Drum potential sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 drum potential sensor and فتوکپی ریکو آفیشیو 1105 BCU
- BCU defective
- Charge/bias/grid power pack defective
SC312: Drum Potential Sensor Error 3
Definition- [D]
When adjusting VD for فتوکپی ریکو آفیشیو 1105 unexposed drum during process control initial setting, –1,000 V is applied to فتوکپی ریکو آفیشیو 1105 charge grid, but فتوکپی ریکو آفیشیو 1105 drum potential sensor detects that VD is more than –970 V. Possible Causes
- Drum potential sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 drum unit and فتوکپی ریکو آفیشیو 1105 BCU
- Charge/bias/grid power pack defective
- Dirty or worn charge corona wire
SC313: Drum Potential Sensor Error 4
Definition [D]
When adjusting فتوکپی ریکو آفیشیو 1105 drum potential (VD) during process control initial setting, فتوکپی ریکو آفیشیو 1105 drum potential sensor detects that VD is more than VG (grid voltage).
Possible Causes
- Drum potential sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 drum potential sensor and فتوکپی ریکو آفیشیو 1105 BCU
- BCU defective
- Charge/bias/grid power pack defective
- Dirty or worn charge corona wire
SC314: Drum Potential Sensor Error 5
Definition [D]
When adjusting فتوکپی ریکو آفیشیو 1105 drum potential (VH) for LD power adjustment during process control initial setting, فتوکپی ریکو آفیشیو 1105 first time فتوکپی ریکو آفیشیو 1105 VHpattern is made, فتوکپی ریکو آفیشیو 1105 drum potential sensor detects that VH is more than 500 V.
Possible Causes
- Drum potential sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 drum potential sensor and فتوکپی ریکو آفیشیو 1105 BCU
- BCU defective
- LDB defective
SC315: Drum Potential Sensor Error 6
Definition [D]
When adjusting VD for فتوکپی ریکو آفیشیو 1105 unexposed drum during process control initial setting, VD does not reach –900 ± 20 V even if VG has been adjusted 5 times.
Possible Causes
- Drum potential sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 drum potential sensor and فتوکپی ریکو آفیشیو 1105 BCU
- BCU defective
- Charge/bias/grid power pack defective
SC316: Drum Potential Sensor Error 7
Definition [D]
When adjusting فتوکپی ریکو آفیشیو 1105 drum potential (VH) for half tone during process control initial setting, فتوکپی ریکو آفیشیو 1105 drum potential sensor detects that VH does not become –265 ± 20 V even though فتوکپی ریکو آفیشیو 1105 LD power has been changed twenty times.
Possible Causes
- Drum potential sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 drum potential sensor and فتوکپی ریکو آفیشیو 1105 IBCU
- BCU defective
- LDB defective
- Poor drum cleaning
SC321: Laser Writing Signal (F-gate) Error
Definition- [B]
فتوکپی ریکو آفیشیو 1105 laser writing signal (F-gate) does not go to LOW for more than 15 seconds after فتوکپی ریکو آفیشیو 1105 copy paper reaches فتوکپی ریکو آفیشیو 1105 registration sensor.
Possible Causes
- SICU board defective
- Poor connection of فتوکپی ریکو آفیشیو 1105 printer controller
- Printer controller defective
SC322: Laser Synchronization Error
Definition [B’]
فتوکپی ریکو آفیشیو 1105 laser synchronization signal cannot be detected from فتوکپی ریکو آفیشیو 1105 synchronization detector even if فتوکپی ریکو آفیشیو 1105 laser diodes are activated.
Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 laser synchronization detector and فتوکپی ریکو آفیشیو 1105 LDB
- Laser synchronization detector out of position
- Laser synchronization detector defective
- LDB defective
- SICU defective
- Front door safety switches defective
SC323: Excessive LD Drive Current
Definition [B’]
فتوکپی ریکو آفیشیو 1105 LDB applies more than 110 mA to فتوکپی ریکو آفیشیو 1105 LD.
Possible Causes
- LDB defective (not enough power, due to aging)
- Poor connection between فتوکپی ریکو آفیشیو 1105 LDB and فتوکپی ریکو آفیشیو 1105 SICU board
- High temperature of LD on LDB
SC335: Polygonal Mirror Motor Error 1
Definition [B]
فتوکپی ریکو آفیشیو 1105 polygonal mirror motor does not reach its operating speed within 20 seconds after فتوکپی ریکو آفیشیو 1105 polygonal mirror motor turns on, or فتوکپی ریکو آفیشیو 1105 polygonal mirror motor speed is changed.
Possible Causes
- Polygonal mirror motor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 polygonal mirror motor drive board and فتوکپی ریکو آفیشیو 1105 SICU board
- Polygonal mirror motor drive board defective
- SICU board defective
SC336: Polygonal Mirror Motor Error 2
Definition [B]
فتوکپی ریکو آفیشیو 1105 SICU does not receive فتوکپی ریکو آفیشیو 1105 stop signal from فتوکپی ریکو آفیشیو 1105 polygonal mirror motor for more than 20 seconds after فتوکپی ریکو آفیشیو 1105 polygonal mirror motor turns off.
Possible Causes
- Polygonal mirror motor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 polygonal mirror motor drive board and فتوکپی ریکو آفیشیو 1105 SICU board
- Polygonal mirror motor drive board defective
- SICU board defective
SC337: Polygonal Mirror Motor Error 3
Definition [B]
فتوکپی ریکو آفیشیو 1105 polygonal mirror motor status is changed even though no signal is sent from فتوکپی ریکو آفیشیو 1105 SICU. Possible Causes
- Polygonal mirror motor defective
- Electrical noise
- Polygonal mirror motor drive board defective
- SICU board defective
SC338: Polygonal Mirror Motor Error 4
Definition [B]
1) فتوکپی ریکو آفیشیو 1105 polygonal mirror motor operating speed does not become stable for 20 seconds after فتوکپی ریکو آفیشیو 1105 polygonal mirror motor is turned on, or فتوکپی ریکو آفیشیو 1105 polygonal mirror motor speed is changed.
2) فتوکپی ریکو آفیشیو 1105 stop signal from فتوکپی ریکو آفیشیو 1105 polygonal mirror motor does not become stable for 20 seconds after فتوکپی ریکو آفیشیو 1105 polygonal mirror motor is turned off.
Possible Causes
- Polygonal mirror motor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 polygonal mirror motor drive board and فتوکپی ریکو آفیشیو 1105 SICU board
- Polygonal mirror motor drive board defective
- SICU board defective
SC340: TD Sensor Error 1
Definition [B]
فتوکپی ریکو آفیشیو 1105 TD sensor output voltage is less than 0.5 V or more than 4.0 V 10 times consecutively during copying.
Possible Causes
- TD sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 TD sensor and فتوکپی ریکو آفیشیو 1105 BCU
- BCU defective
- Toner supply defective
SC341: TD Sensor Error 2
Definition [B]
One of فتوکپی ریکو آفیشیو 1105 following TD sensor output voltages is detected during TD sensor initial setting.
1) Less than 2.5 V when فتوکپی ریکو آفیشیو 1105 maximum PWM (255) is applied to فتوکپی ریکو آفیشیو 1105 TD sensor. 2) 2.5 V or more when minimum PWM (0) is applied to فتوکپی ریکو آفیشیو 1105 TD sensor.
Possible Causes
- TD sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 TD sensor and فتوکپی ریکو آفیشیو 1105 BCU
- BCU defective
- Toner supply defective
SC342: TD Sensor Error 3
Definition [B]
فتوکپی ریکو آفیشیو 1105 TD sensor output voltage is not adjusted to 2.5 ± 0.1 V within 20 seconds during TD sensor initial setting.
Possible Causes
- TD sensor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 TD sensor and فتوکپی ریکو آفیشیو 1105 BCU
- BCU defective
- Toner supply defective
SC345: Development Bias Leak
Definition [B]
Maximum PWM for فتوکپی ریکو آفیشیو 1105 development bias signal is applied 10 times consecutively. Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 development bias terminal and فتوکپی ریکو آفیشیو 1105 charge/bias/grid power pack
- Charge/bias/grid power pack
SC350: ID Sensor Error 1
Definition [D]
One of فتوکپی ریکو آفیشیو 1105 following ID sensor output voltages was detected when checking فتوکپی ریکو آفیشیو 1105 ID sensor pattern.
1) VSP ≥ 2.5 V
2) VSP = 0 V Possible Causes
- ID sensor defective
- ID sensor connector defective
- Poor ID sensor connector connection
- BCU defective
- Charge/bias/grid power pack defective
- Dirty ID sensor
- Defect on فتوکپی ریکو آفیشیو 1105 drum at فتوکپی ریکو آفیشیو 1105 ID sensor pattern writing area
SC351: ID Sensor Error 2
Definition [D]
فتوکپی ریکو آفیشیو 1105 following two conditions were detected at فتوکپی ریکو آفیشیو 1105 same time when checking فتوکپی ریکو آفیشیو 1105 ID sensor pattern.
1) VSG ≤ 2.5 V or VSG= 0 V
2) فتوکپی ریکو آفیشیو 1105 ID sensor output voltage is 5.0 V and فتوکپی ریکو آفیشیو 1105 PWM signal input to فتوکپی ریکو آفیشیو 1105 ID sensor is 0
Possible Causes
- ID sensor defective
- ID sensor connector defective
- Poor ID sensor connector connection
- BCU defective
- Charge/bias/grid pack defective
- Dirty ID sensor
- Defect on فتوکپی ریکو آفیشیو 1105 drum at فتوکپی ریکو آفیشیو 1105 ID sensor pattern writing area
SC352: ID Sensor Error 3
Definition [D]
فتوکپی ریکو آفیشیو 1105 ID sensor pattern edge voltage is not at 2.5 V for 1.5 seconds during فتوکپی ریکو آفیشیو 1105 ID sensor pattern check.
Possible Causes
- ID sensor defective
- ID sensor connector defective
- Poor ID sensor connector connection
- BCU defective
- Charge/bias/grid pack defective
- Dirty ID sensor
- Defect on فتوکپی ریکو آفیشیو 1105 drum at فتوکپی ریکو آفیشیو 1105 ID sensor pattern writing area
SC353: ID Sensor Error 4
Definition [D]
One of فتوکپی ریکو آفیشیو 1105 following ID sensor output voltages is detected at ID sensor initialization.
1) VSG < 4.0 V when فتوکپی ریکو آفیشیو 1105 maximum PWM input (255) is applied to فتوکپی ریکو آفیشیو 1105 ID sensor.
2) VSG ≥ 4.0 V when فتوکپی ریکو آفیشیو 1105 minimum PWM input (0) is applied to فتوکپی ریکو آفیشیو 1105 ID sensor.
Possible Causes
- ID sensor defective
- ID sensor connector defective
- Poor ID sensor connector connection
- BCU defective
- Charge/bias/grid pack defective
- Dirty ID sensor
- Defect on فتوکپی ریکو آفیشیو 1105 drum at فتوکپی ریکو آفیشیو 1105 ID sensor pattern writing area
SC354: ID Sensor Error 5
Definition [D]
VSG is not adjusted within فتوکپی ریکو آفیشیو 1105 target (4.0 ± 0.2 V) within 20 seconds during VSG checking. Possible Causes
- ID sensor defective
- ID sensor connector defective
- Poor ID sensor connector connection
- BCU defective
- Charge/bias/grid pack defective
- Dirty ID sensor
- Defect on فتوکپی ریکو آفیشیو 1105 drum at فتوکپی ریکو آفیشیو 1105 ID sensor pattern writing area
SC355: ID Sensor Voltage Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 ID sensor voltage (VP) exceeds 700 V, 10 times consecutively.
Possible Causes
- Drum potential sensor defective
- IO Board defective
- Poor connection of فتوکپی ریکو آفیشیو 1105 drum unit connector
- LD defective
- Poor drum cleaning
- Dirty optics
- Drum wear
SC360: Hard Disk Drive Error 1
Definition [B]
فتوکپی ریکو آفیشیو 1105 machine does not detect فتوکپی ریکو آفیشیو 1105 connection signal from HDD 1 when فتوکپی ریکو آفیشیو 1105 main switch is turned on. Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 HDD and SICU
- فتوکپی ریکو آفیشیو 1105 dc power connector to فتوکپی ریکو آفیشیو 1105 HDD is disconnected
- HDD defective
- SICU defective
SC361: Hard Disk Drive Error 2
Definition [C]
فتوکپی ریکو آفیشیو 1105 machine does not detect فتوکپی ریکو آفیشیو 1105 connection signal from HDD 2 when فتوکپی ریکو آفیشیو 1105 main switch is turned on. Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 HDD and SICU
- فتوکپی ریکو آفیشیو 1105 dc power connector to فتوکپی ریکو آفیشیو 1105 HDD is disconnected
- HDD defective
- SICU defective
SC362: Hard Disk Drive Error 3
Definition [C]
فتوکپی ریکو آفیشیو 1105 machine does not detect فتوکپی ریکو آفیشیو 1105 connection signal from HDD 1 when فتوکپی ریکو آفیشیو 1105 operation switch is turned on.
Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 HDD and SICU
- فتوکپی ریکو آفیشیو 1105 dc power connector to فتوکپی ریکو آفیشیو 1105 HDD is disconnected
- HDD defective
- SICU defective
SC363: Hard Disk Drive Error 4
Definition [C]
فتوکپی ریکو آفیشیو 1105 machine does not detect فتوکپی ریکو آفیشیو 1105 connection signal from HDD 2 when فتوکپی ریکو آفیشیو 1105 operation switch is turned on.
Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 HDD and SICU
- فتوکپی ریکو آفیشیو 1105 dc power connector to فتوکپی ریکو آفیشیو 1105 HDD is disconnected
- HDD defective
- SICU defective
SC364: Hard Disk Drive Error 5
Definition [C]
فتوکپی ریکو آفیشیو 1105 image data stored in HDD 1 cannot be output properly.
Possible Causes
- When this SC occurs only once, this problem will be solved after turning فتوکپی ریکو آفیشیو 1105 main power switch off and on.
- When this SC occurs while performing SP4-911-1 (HDD 1 media check), it can be cured by doing SP4-911-2 (HDD 1 formatting). • HDD 1 defective
SC365: Hard Disk Drive Error 6
Definition [C]
فتوکپی ریکو آفیشیو 1105 image data stored in HDD 2 cannot be output properly.
Possible Causes
- When this SC occurs only once, this problem will be solved after turning فتوکپی ریکو آفیشیو 1105 main power switch off and on.
- When this SC occurs while performing SP4-912-1 (HDD 2 media check), it can be cured by doing SP4-912-2 (HDD 2 formatting). • HDD 2 defective
SC366: Hard Disk Drive Error 7
Definition [C]
فتوکپی ریکو آفیشیو 1105 number of bad sectors in HDD 1 exceeds فتوکپی ریکو آفیشیو 1105 maximum value.
Possible Causes
- NVRAM defective
- HDD 1 defective
SC367: Hard Disk Drive Error 8
Definition [C]
فتوکپی ریکو آفیشیو 1105 number of bad sectors in HDD 2 exceeds فتوکپی ریکو آفیشیو 1105 maximum value.
Possible Causes
- NVRAM defective
- HDD 2 defective
SC370, 371, 372, 373, 374, 375: IMAC (Image Compression IC) Error 1
Definition [B]
An error occurs during image processing in فتوکپی ریکو آفیشیو 1105 IMAC, which handles image compression and image data transfer between فتوکپی ریکو آفیشیو 1105 machine’s components.
Possible Causes
- SICU defective
SC376, 377: IMAC (Image Compression IC) Error 2
Definition [B]
While image data is transferred in tandem mode, an error occurs during image processing in فتوکپی ریکو آفیشیو 1105 IMAC, which handles image compression and image data transfer between فتوکپی ریکو آفیشیو 1105 machine’s components.
Possible Causes
- SICU defective
SC380, 381, 382, 383: Image Data Transfer Timeout
Definition [B]
فتوکپی ریکو آفیشیو 1105 image data could not be transferred to فتوکپی ریکو آفیشیو 1105 memory within 20 seconds.
Possible Causes
- SICU defective
- Printer controller defective
- SBU defective
SC384, 385: Image Data Transfer Timeout in Tandem Mode
Definition [B]
فتوکپی ریکو آفیشیو 1105 image data could not be transferred to فتوکپی ریکو آفیشیو 1105 memory within 20 seconds in tandem mode. Possible Causes
- SICU defective
- Printer controller defective
- SBU defective
- Interface board defective
SC386, 387: Image Data Transfer Timeout (HDD)
Definition [B]
فتوکپی ریکو آفیشیو 1105 image data could not be transferred to فتوکپی ریکو آفیشیو 1105 HDD within 15 seconds.
Possible Causes
- SICU defective
- Printer controller defective
- SBU defective
- Interface board defective
SC390: Tandem Image Data Transfer Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 image data sent from فتوکپی ریکو آفیشیو 1105 master does not match فتوکپی ریکو آفیشیو 1105 data received by slave. Possible Causes
- SICU defective
- Interface board defective
- Electrical noise
SC391, 392: Image Storage Address Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 SICU receives an image data output request signal for data that is not stored in memory. Possible Causes
- SICU defective
SC395: CD-R/RW Control CPU Error
Definition [C] (All copier functions can be used except for “Document Editor”). فتوکپی ریکو آفیشیو 1105 CD-R/RW control CPU on فتوکپی ریکو آفیشیو 1105 interface board generates an abnormal signal.
Possible Causes:
- Interface board defective
SC397: CD Access Error
Definition [C] (All copier functions can be used except for “Document Editor”). فتوکپی ریکو آفیشیو 1105 CD-R/RW generates an abnormal signal during data transmittion between فتوکپی ریکو آفیشیو 1105 copier HDD and فتوکپی ریکو آفیشیو 1105 CD-R/RW.
Possible Causes:
- CD-R/RW defective
- CD-R/RW media defective
SC397: CD-R/RW Data Transmission Error
Definition [C] (All copier functions can be used except for “Document Editor”).
Data transmission between فتوکپی ریکو آفیشیو 1105 copier HDD and فتوکپی ریکو آفیشیو 1105 CD-R/RW is not completed within 105 seconds.
Possible Causes:
- CD-R/RW defective
- CD-R/RW media defective
SC400: Transfer Bias Roller Leak
Definition [B]
Abnormal feedback data from فتوکپی ریکو آفیشیو 1105 transfer power pack is detected 6 times consecutively. Possible Causes
- Transfer power pack defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 transfer current terminal and فتوکپی ریکو آفیشیو 1105 transfer power pack.
SC401: Transfer roller open error
Definition [B]
فتوکپی ریکو آفیشیو 1105 following conditions are detected at فتوکپی ریکو آفیشیو 1105 same time 6 times consecutively.
1) فتوکپی ریکو آفیشیو 1105 transfer bias roller feedback data is less than فتوکپی ریکو آفیشیو 1105 minimum target. 2) Maximum PWM for فتوکپی ریکو آفیشیو 1105 transfer bias roller is applied.
Possible Causes
- Transfer power pack defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 transfer current terminal and فتوکپی ریکو آفیشیو 1105 transfer power pack.
SC430: Quenching Lamp Error
Definition [D]
When finishing فتوکپی ریکو آفیشیو 1105 process control initial setting, فتوکپی ریکو آفیشیو 1105 drum potential which is detected by فتوکپی ریکو آفیشیو 1105 drum potential sensor is out of فتوکپی ریکو آفیشیو 1105 normal range.
Possible Causes
- Quenching lamp defective
- Poor connection between quenching lamp and charge/bias/grid power pack
SC440: Drum Motor Lock
Definition [B]
فتوکپی ریکو آفیشیو 1105 drum motor lock signal is longer than 2 seconds while فتوکپی ریکو آفیشیو 1105 drum motor is on. Possible Causes
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Drum motor defective
- Poor drum motor connector connection
- BCU defective
SC441: Development Motor Lock
Definition [B]
فتوکپی ریکو آفیشیو 1105 development motor lock signal is longer than 2 seconds while فتوکپی ریکو آفیشیو 1105 development motor is on.
Possible Causes
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Development motor defective
- Poor development motor connector connection
- BCU defective
SC491: Polygonal Mirror Motor Cooling Fan Motor Lock
Definition [B]
فتوکپی ریکو آفیشیو 1105 polygonal mirror motor cooling fanmotor lock signal is longer than 5 seconds while فتوکپی ریکو آفیشیو 1105 polygonal mirror motor cooling fan motor is on.
Possible Causes
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Polygonal mirror motor cooling fan motor defective
SC495: Toner Bottle Unit Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 toner hopper sensor cannot detect toner even if فتوکپی ریکو آفیشیو 1105 toner supply coil clutch turns on for 2 seconds x 10 times during toner supply during copying.
Possible Causes
- Toner supply motor defective
- Toner supply coil clutch defective
- Toner supply motor connector connection
- Toner supply coil clutch connector connection
- Toner near-end sensor (in فتوکپی ریکو آفیشیو 1105 toner bank) defective
- Toner hopper sensor defective
- Toner clogged in فتوکپی ریکو آفیشیو 1105 supply system
SC496: Toner Collection Bottle Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 used toner collection bottle or sucked toner collection bottle sensor remains off for 3 seconds.
Possible Causes
- Used toner collection bottle or sucked toner collection bottle is incorrectly set
- Used toner collection bottle or sucked toner collection bottle connector is loose or sensor defective
SC501: 1st Tray Lift Malfunction
Definition [C]
One of فتوکپی ریکو آفیشیو 1105 following conditions is detected in فتوکپی ریکو آفیشیو 1105 1st tray.
1) فتوکپی ریکو آفیشیو 1105 1st lift sensor is not activated for 10 seconds after فتوکپی ریکو آفیشیو 1105 tray lift motor turned on.
2) فتوکپی ریکو آفیشیو 1105 1st lift sensor is already activated when فتوکپی ریکو آفیشیو 1105 1st tray is placed in فتوکپی ریکو آفیشیو 1105 machine.
Possible Causes
- 1st lift sensor defective
- 1st tray lift motor defective
- Poor 1st pick-up solenoid connection
- Poor 1st tray lift motor connection
SC502: 2nd Tray Lift Malfunction
Definition [C]
One of فتوکپی ریکو آفیشیو 1105 following conditions is detected in فتوکپی ریکو آفیشیو 1105 2nd tray.
1) فتوکپی ریکو آفیشیو 1105 2nd lift sensor is not activated for 10 seconds after فتوکپی ریکو آفیشیو 1105 tray lift motor turned on.
2) فتوکپی ریکو آفیشیو 1105 2nd lift sensor is already activated when فتوکپی ریکو آفیشیو 1105 2nd tray is placed in فتوکپی ریکو آفیشیو 1105 machine.
Possible Causes
- 2nd lift sensor defective
- 2nd tray lift motor defective
- Poor 2nd pick-up solenoid connection
- Poor 2nd tray lift motor connection
SC503: 3rd Tray Lift Malfunction
Definition [C]
One of فتوکپی ریکو آفیشیو 1105 following conditions is detected in فتوکپی ریکو آفیشیو 1105 3rd tray.
1) فتوکپی ریکو آفیشیو 1105 3rd lift sensor is not activated for 10 seconds after فتوکپی ریکو آفیشیو 1105 tray lift motor turned on.
2) فتوکپی ریکو آفیشیو 1105 3rd lift sensor is already activated when فتوکپی ریکو آفیشیو 1105 3rd tray is placed in فتوکپی ریکو آفیشیو 1105 machine.
Possible Causes
- 3rd lift sensor defective
- 3rd tray lift motor defective
- Poor 3rd pick-up solenoid connection
- Poor 3rd tray lift motor connection
SC504: LCT 1st Tray Lift Malfunction
Definition [C]
One of فتوکپی ریکو آفیشیو 1105 following conditions is detected in فتوکپی ریکو آفیشیو 1105 LCT 1st tray.
1) فتوکپی ریکو آفیشیو 1105 LCT 1st lift sensor is not activated for 10 seconds after فتوکپی ریکو آفیشیو 1105 tray lift motor turned on.
2) فتوکپی ریکو آفیشیو 1105 LCT 1st lift sensor is already activated when فتوکپی ریکو آفیشیو 1105 LCT 1st tray is placed in فتوکپی ریکو آفیشیو 1105 machine.
Possible Causes
- LCT 1st lift sensor defective
- LCT 1st tray lift motor defective
- Poor LCT 1st pick-up solenoid connection
- Poor LCT 1st tray lift motor connection
SC505: LCT 2nd Tray Lift Malfunction
Definition [C]
One of فتوکپی ریکو آفیشیو 1105 following conditions is detected in فتوکپی ریکو آفیشیو 1105 LCT 2nd tray.
1) فتوکپی ریکو آفیشیو 1105 LCT 2nd lift sensor is not activated for 10 seconds after فتوکپی ریکو آفیشیو 1105 tray lift motor turned on.
2) فتوکپی ریکو آفیشیو 1105 LCT 2nd lift sensor is already activated when فتوکپی ریکو آفیشیو 1105 LCT 2nd tray is placed in فتوکپی ریکو آفیشیو 1105 machine.
Possible Causes
- LCT 2nd lift sensor defective
- LCT 2nd tray lift motor defective
- Poor LCT 2nd pick-up solenoid connection
- Poor LCT 2nd tray lift motor connection
SC506: LCT 3rd Tray Lift Malfunction
Definition [C]
One of فتوکپی ریکو آفیشیو 1105 following conditions is detected in فتوکپی ریکو آفیشیو 1105 LCT 3rd tray.
1) فتوکپی ریکو آفیشیو 1105 LCT 3rd lift sensor is not activated for 10 seconds after فتوکپی ریکو آفیشیو 1105 tray lift motor turned on.
2) فتوکپی ریکو آفیشیو 1105 LCT 3rd lift sensor is already activated when فتوکپی ریکو آفیشیو 1105 LCT 3rd tray is placed in فتوکپی ریکو آفیشیو 1105 machine.
Possible Causes
- LCT 3rd lift sensor defective
- LCT 3rd tray lift motor defective
- Poor LCT 3rd pick-up solenoid connection
- Poor LCT 3rd tray lift motor connection
SC510: Paper Feed Motor Lock
Definition [B]
A paper feed motor lock signal is detected for more than 50 ms during rotation.
Possible Causes
- Paper feed motor defective
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Poor paper feed motor connector connection
SC511: LCT Motor Lock (Optional LCT)
Definition [B]
An LCT motor lock signal is detected for more than 50 ms during rotation.
Possible Causes
- LCT motor defective
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Poor LCT motor connector connection
SC515: Tandem Rear Fence Drive Motor Error
Definition [C]
One of فتوکپی ریکو آفیشیو 1105 following conditions is detected in فتوکپی ریکو آفیشیو 1105 tandem tray.
1) فتوکپی ریکو آفیشیو 1105 rear fence return sensor and فتوکپی ریکو آفیشیو 1105 rear fence HP sensor are on at فتوکپی ریکو آفیشیو 1105 same time.
2) It takes 10 seconds or more for فتوکپی ریکو آفیشیو 1105 rear fence return sensor to detect فتوکپی ریکو آفیشیو 1105 on condition after فتوکپی ریکو آفیشیو 1105 rear fence drive motor starts.
3) It takes 10 seconds or more for فتوکپی ریکو آفیشیو 1105 rear fence HP sensor to detect فتوکپی ریکو آفیشیو 1105 on condition after this fence starts moving to فتوکپی ریکو آفیشیو 1105 home position.
Possible Causes
- Rear fence drive motor defective
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Poor motor connector connection
SC520: Jogger Motor Error 1
Definition [C]
When فتوکپی ریکو آفیشیو 1105 jogger fence moves to فتوکپی ریکو آفیشیو 1105 home position, فتوکپی ریکو آفیشیو 1105 jogger HP sensor does not turn on even if فتوکپی ریکو آفیشیو 1105 jogger fence motor has moved فتوکپی ریکو آفیشیو 1105 jogger fence 153.5 mm.
Possible Causes
- Jogger fence motor defective
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Poor motor connector connection
SC521: Duplex Jogger Motor Error 2
Definition [C]
When فتوکپی ریکو آفیشیو 1105 jogger fence moves from فتوکپی ریکو آفیشیو 1105 home position, فتوکپی ریکو آفیشیو 1105 jogger fence HP sensor does not turn off even if فتوکپی ریکو آفیشیو 1105 jogger motor has moved فتوکپی ریکو آفیشیو 1105 jogger fence 153.5 mm. Possible Causes
- Jogger fence motor defective
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Poor motor connector connection
SC531: Fusing/Duplex Motor Lock
Definition [B]
A fusing/duplex motor lock signal is detected for more than 2 seconds during rotation. Possible Causes
- Fusing/duplex motor defective
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Poor fusing/duplex motor connector connection
- BCU defective
- Front door safety switches defective
SC532: Relay Motor Lock
Definition [C]
A relay motor lock signal is detected for more than 2 seconds during rotation.
Possible Causes
- Relay motor defective
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- Poor relay motor connector connection
- BCU defective
SC541: Fusing فتوکپی ریکو آفیشیو 1105rmistor Open
Definition [A]
فتوکپی ریکو آفیشیو 1105 fusing temperature detected by فتوکپی ریکو آفیشیو 1105 فتوکپی ریکو آفیشیو 1105rmistor was below 7°C for 15 seconds. Possible Causes
- Fusing فتوکپی ریکو آفیشیو 1105rmistor defective or out of position
- Poor فتوکپی ریکو آفیشیو 1105rmistor terminal connection
SC542: Fusing Temperature Warming-up Error
Definition [A]
فتوکپی ریکو آفیشیو 1105 fusing temperature does not reach فتوکپی ریکو آفیشیو 1105 fusing standby temperature within 6 minutes after فتوکپی ریکو آفیشیو 1105 main power switch is turned on, or after فتوکپی ریکو آفیشیو 1105 front doors are closed. Possible Causes
- Fusing فتوکپی ریکو آفیشیو 1105rmistor defective or out of position
- Fusing lamp open
- Fusing فتوکپی ریکو آفیشیو 1105rmofuse open
- BCU defective
- AC drive board defective
- Poor fusing unit connection
SC543: Fusing Overheat Error 1
Definition [A]
A fusing temperature of over 220°C is detected for 5 seconds by فتوکپی ریکو آفیشیو 1105 fusing فتوکپی ریکو آفیشیو 1105rmistor. Possible Causes
- Fusing فتوکپی ریکو آفیشیو 1105rmistor defective
- BCU defective
SC544: Fusing Overheat Error 2
Definition [A]
فتوکپی ریکو آفیشیو 1105 fusing temperature monitoring circuit defects abnormal fusing temperature.
Possible Causes
- Fusing فتوکپی ریکو آفیشیو 1105rmistor defective
- BCU defective
SC545: Fusing Overheat Error 3
Definition [A]
فتوکپی ریکو آفیشیو 1105 fusing lamp stays on at full power for 45 seconds while in فتوکپی ریکو آفیشیو 1105 stand-by condition after warming-up is completed.
Possible Causes
- Fusing فتوکپی ریکو آفیشیو 1105rmistor out of position
SC546: Fusing Ready Temperature Malfunction
Definition [A]
فتوکپی ریکو آفیشیو 1105 fusing temperature twice consecutively is detected 20°C lower or 20°C higher than فتوکپی ریکو آفیشیو 1105 temperature 1 second earlier.
Possible Causes
- Poor فتوکپی ریکو آفیشیو 1105rmistor connector connection
- Poor fusing unit connection
SC547: Zero Cross Signal Malfunction
Definition [A]
When one of فتوکپی ریکو آفیشیو 1105 following conditions is detected 10 times consecutively.
1) More than 66 or fewer than 45 zero-cross signals in 500 ms.
2) An interval between zero-cross signals shorter than 7.5 ms is detected 3 times in 500 ms.
Possible Causes
- Noise on فتوکپی ریکو آفیشیو 1105 ac power line
SC550: Oil Supply/Cleaning Web End
Definition [A]
فتوکپی ریکو آفیشیو 1105 oil supply/cleaning web end sensor stays on for 500 ms after فتوکپی ریکو آفیشیو 1105 oil supply/web end motor starts. Possible Causes
- Oil supply/cleaning web end
- Oil supply/cleaning web motor defective
SC591: Toner Supply Motor Lock
Definition [B]
فتوکپی ریکو آفیشیو 1105 used toner supply motor sensor status or development suction motor sensor does not change for 1 second while فتوکپی ریکو آفیشیو 1105 toner supply motor is energized. Possible Causes
- Used toner supply motor or development suction motor defective
- Used toner supply motor sensor or development suction motor sensor defective
- BCU defective
SC592: Toner Bank Motor Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 BCU receives an abnormal signal from فتوکپی ریکو آفیشیو 1105 toner bank motor.
Possible Causes
- Toner bank motor defective
- Too much load on فتوکپی ریکو آفیشیو 1105 drive mechanism
- BCU defective
SC601: Communication Error Between SICU and SBU
Definition [B’]
فتوکپی ریکو آفیشیو 1105 SICU cannot communicate with فتوکپی ریکو آفیشیو 1105 SBU board properly.
Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and SBU
- SBU defective
- SICU defective
SC602: Communication Error Between SICU and HDD Controller
Definition [B]
فتوکپی ریکو آفیشیو 1105 SICU cannot communicate with فتوکپی ریکو آفیشیو 1105 HDD controller properly.
Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU board and HDD
- SICU board defective
SC620: Communication Error between BCU and ADF 1
Definition [B’]
فتوکپی ریکو آفیشیو 1105 TXD and RXD signals between BCU and ADF main board do not stabilize.
Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 BCU board and فتوکپی ریکو آفیشیو 1105 ADF main board
- Noise on interface cable
SC621: Communication Error between BCU and ADF 2
Definition [B’]
فتوکپی ریکو آفیشیو 1105 TXD and RXD signals between BCU and ADF main board do not stabilize.
Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 BCU board and فتوکپی ریکو آفیشیو 1105 ADF main board
- ADF main board defective
- BCU board defective
SC622: Communication Error between BCU and ADF 3
Definition- [B’]
Software error after abnormal user operation.
Possible Causes
- Software error
SC625, 626: Communication Error between BCU and Finisher
Definition [B]
فتوکپی ریکو آفیشیو 1105 BCU cannot communicate with فتوکپی ریکو آفیشیو 1105 finisher properly.
Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 BCU board and فتوکپی ریکو آفیشیو 1105 finisher main board
- Finisher main board defective
- BCU board defective
- Noise on فتوکپی ریکو آفیشیو 1105 interface cable
SC630: CSS (RSS) Communication Error between Line Adapter and CSS Center
- Japan only
SC640: Communication Error between SICU and BCU (CH1) 1
Definition [B]
فتوکپی ریکو آفیشیو 1105 SICU cannot communicate with فتوکپی ریکو آفیشیو 1105 BCU properly. Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and BCU boards
- SICU board defective
- BCU board defective
- Noise on فتوکپی ریکو آفیشیو 1105 interface cable
SC641: Communication Error between SICU and BCU (CH1) 2
Definition [A]
فتوکپی ریکو آفیشیو 1105 BCU cannot receive فتوکپی ریکو آفیشیو 1105 data from فتوکپی ریکو آفیشیو 1105 SICU properly.
Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and BCU boards
- SICU board defective
- BCU board defective
- Noise on فتوکپی ریکو آفیشیو 1105 interface cable
SC642: Communication Error between SICU and BCU (CH1) 3
Definition [B]
فتوکپی ریکو آفیشیو 1105 SICU cannot receive فتوکپی ریکو آفیشیو 1105 data from فتوکپی ریکو آفیشیو 1105 BCU properly. Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and BCU boards
- SICU board defective
- BCU board defective
- Noise on فتوکپی ریکو آفیشیو 1105 interface cable
SC643: Communication Error between SICU and BCU (CH2) 1
Definition [B]
فتوکپی ریکو آفیشیو 1105 SICU cannot communicate with فتوکپی ریکو آفیشیو 1105 BCU properly. Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and BCU boards
- SICU board defective
- BCU board defective
- Noise on فتوکپی ریکو آفیشیو 1105 interface cable
SC644: Communication Error between SICU and BCU (CH2) 2
Definition [A]
فتوکپی ریکو آفیشیو 1105 BCU cannot receive فتوکپی ریکو آفیشیو 1105 data from فتوکپی ریکو آفیشیو 1105 SICU properly. Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and BCU boards
- SICU board defective
- BCU board defective
- Noise on فتوکپی ریکو آفیشیو 1105 interface cable
SC645: Communication Error between SICU and BCU (CH2) 3
Definition [B]
فتوکپی ریکو آفیشیو 1105 SICU cannot receive فتوکپی ریکو آفیشیو 1105 data from فتوکپی ریکو آفیشیو 1105 BCU properly. Possible Causes
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and BCU boards
- SICU board defective
- BCU board defective
- Noise on فتوکپی ریکو آفیشیو 1105 interface cable
SC646: SICU Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 BICU detects a defective SICU.
Possible Causes
- SICU board defective
SC650: Optional Counter Error 1 • Japanese version only
SC651: Optional Counter Error 2 • Japanese version only
SC652: Optional Counter Error 3 • Japanese version only
SC653: Optional Counter Error 4
- Japanese version only
SC701: ADF Pick-up Roller Release Malfunction
Definition [B’]
فتوکپی ریکو آفیشیو 1105 pick-up roller HP sensor does not activate or de-activate when فتوکپی ریکو آفیشیو 1105 pick-up motor turns on. Possible Causes
- Pick-up roller HP sensor defective
- Pick-up motor defective
- ADF main board defective
SC702: ADF Feed-in Motor Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 feed-in motor does not turn properly.
Possible Causes
- Feed-in motor defective
- ADF main board defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 feed-in motor and ADF main board • Too much load
SC703: ADF Transport Belt Motor Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 transport belt motor does not turn properly.
Possible Causes
- Transport belt motor defective
- ADF main board defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 transport motor and ADF main board
- Too much load
SC704: ADF Feed-out Motor Error
Definition [B’]
فتوکپی ریکو آفیشیو 1105 feed-out motor does not turn properly
Possible Causes
- Feed-out motor defective
- ADF main board defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 feed-out motor and ADF main board
- Too much load
SC705: ADF Original Table Lift Malfunction
Definition [B]
One of فتوکپی ریکو آفیشیو 1105 following conditions was detected.
1) فتوکپی ریکو آفیشیو 1105 bottom plate position sensor does not activate when فتوکپی ریکو آفیشیو 1105 original table motor lifts فتوکپی ریکو آفیشیو 1105 original table.
2) فتوکپی ریکو آفیشیو 1105 bottom plate HP sensor does not activate when فتوکپی ریکو آفیشیو 1105 bottom plate motor lowers فتوکپی ریکو آفیشیو 1105 original table.
Possible Causes
- Bottom plate H.P sensor defective
- Bottom plate motor defective
- ADF main board defective
- Bottom plate position sensor defective
SC720: Finisher Lower Transport Motor Error
Definition [B’]
فتوکپی ریکو آفیشیو 1105 lower transport motor does not turn properly
Possible Causes
- Lower transport motor defective
- Finisher main board defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 lower transport motor and finisher main board • Too much load
SC722: Finisher Jogger Motor Error
Definition [B]
1) فتوکپی ریکو آفیشیو 1105 finisher jogger HP sensor remains de-activated for more than a certain time when returning to home position.
2) فتوکپی ریکو آفیشیو 1105 finisher jogger HP sensor remains activated for more than a certain time when moving away from home position.
Possible Causes
- Jogger H.P sensor defective
- Jogger motor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 jogger motor and finisher main board
- Too much load
SC724: Finisher Staple Hammer Motor Error
Definition [B]
Stapling does not finish within a certain time after فتوکپی ریکو آفیشیو 1105 staple hammer motor turned on. Possible Causes
- Staple hammer motor defective
- Staple jam
- Too much load on فتوکپی ریکو آفیشیو 1105 stapling mechanism
- Poor hammer motor cable connection
SC725: Finisher Stack Feed-out Motor Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 stack feed-out belt HP sensor does not activate within a certain time after فتوکپی ریکو آفیشیو 1105 stack feed-out motor turned on. Possible Causes
- Stack feed-out HP sensor defective
- Stack feed-out motor defective
- Too much load
- Poor stack feed-out motor cable connection
SC726: Finisher Shift Motor Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 shift tray half-turn sensor status does not change within 1 second after فتوکپی ریکو آفیشیو 1105 shift motor turns on. Possible Causes
- Shift motor defective
- Shift tray half-turn sensor defective
- Too much load
SC727: Finisher Stapler Rotation Motor Error
Definition [B]
1) Stapler rotation does not finish within a certain time after فتوکپی ریکو آفیشیو 1105 stapler rotation motor turned on.
2) فتوکپی ریکو آفیشیو 1105 stapler does not return to its home position within a certain time after stapling finished.
Possible Causes
- Stapler rotation motor defective
- Poor stapler rotation motor connection
- Staple rotation HP sensor defective
- Too much load
SC729: Finisher Punch Motor Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 punch HP sensor is not activated within a certain time after فتوکپی ریکو آفیشیو 1105 punch motor turned on. Possible Causes
- Punch motor defective
- Punch HP sensor defective
- Poor punch motor connection
SC730: Finisher Stapler Motor Error
Definition [B]
1) فتوکپی ریکو آفیشیو 1105 stapler HP sensor stays on for longer than normal when فتوکپی ریکو آفیشیو 1105 stapler motor turns on to return فتوکپی ریکو آفیشیو 1105 stapler to its home position.
2) فتوکپی ریکو آفیشیو 1105 stapler HP sensor does not turn on within a certain time after فتوکپی ریکو آفیشیو 1105 stapler motor turned on to move فتوکپی ریکو آفیشیو 1105 stapler away from home position.
Possible Causes
- Stapler motor defective
- Stapler HP sensor defective
- Poor stapler motor connection
SC735: Finisher Paper Stack Plate Motor Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 stack plate HP sensor does not turn on within a certain time after فتوکپی ریکو آفیشیو 1105 stack plate motor turned on. Possible Causes
- Stack plate motor defective
- Stack plate HP sensor defective
- Poor stack plate motor connection
SC735: Finisher Exit Guide Motor Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 exit guide open sensor does not change within 750 mm after فتوکپی ریکو آفیشیو 1105 exit guide motor is energized. Possible Causes
- Exit guide motor defective
- Exit guide open sensor defective
- Poor exit guide motor connection
SC737: Full Finisher Staple Hopper
Definition [B]
فتوکپی ریکو آفیشیو 1105 staple waste hopper is full.
Possible Causes
- Full staple waste hopper
- Staple waste hopper sensor defective
SC738: Finisher Shift Tray Lift Motor Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 stack height sensor does not activate within a certain time after فتوکپی ریکو آفیشیو 1105 shift tray lift motor turned on.
Possible Causes
- Shift tray lift motor defective
- Too much load
SC900: Electrical Total Counter Error
Definition [A]
فتوکپی ریکو آفیشیو 1105 total counter contains something that is not a number.
Possible Causes
- NVRAM defective
SC901: Mechanical Total Counter Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 mechanical total counter is disconnected.
Possible Causes
- Mechanical total counter defective
SC951: F-gate Signal Error
Definition [B’]
When فتوکپی ریکو آفیشیو 1105 IPU has already received فتوکپی ریکو آفیشیو 1105 F-gate signal (laser writing start trigger signal), فتوکپی ریکو آفیشیو 1105 IPU receives anoفتوکپی ریکو آفیشیو 1105r F-gate signal.
Possible Causes
- SICU defective
SC953: Scanner Image Setting Error
Definition [B’]
فتوکپی ریکو آفیشیو 1105 settings that are required for image processing using فتوکپی ریکو آفیشیو 1105 scanner are not sent from فتوکپی ریکو آفیشیو 1105 IPU. Possible Causes
- Software defective
SC954: Printer Image Setting Error
Definition [B’]
فتوکپی ریکو آفیشیو 1105 settings that are required for image processing using فتوکپی ریکو آفیشیو 1105 printer controller are not sent from فتوکپی ریکو آفیشیو 1105 IPU.
Possible Causes
- Software defective
SC955: Memory Setting Error
Definition [B’]
فتوکپی ریکو آفیشیو 1105 settings that are required for image processing using فتوکپی ریکو آفیشیو 1105 memory are not sent from فتوکپی ریکو آفیشیو 1105 IPU. Possible Causes
- Software defective
SC964: Printer Ready Error
Definition [B’]
فتوکپی ریکو آفیشیو 1105 print ready signal is not generated for more than 17 seconds after فتوکپی ریکو آفیشیو 1105 IPU received فتوکپی ریکو آفیشیو 1105 print start signal.
Possible Causes
- Software defective
SC966: Polygon Mirror Motor Ready Error
Definition [B]
فتوکپی ریکو آفیشیو 1105 polygon mirror motor does not reach ready status within 15 seconds after فتوکپی ریکو آفیشیو 1105 copy paper is detected by فتوکپی ریکو آفیشیو 1105 registration sensor.
Possible Causes:
- Polygon mirror motor defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 polygon mirror motor drive board and SICU board
- Polygon mirror motor drive board defective
- SICU board defective
SC970: Scanner Ready Error
Definition [B’]
فتوکپی ریکو آفیشیو 1105 scan ready signal is not generated by فتوکپی ریکو آفیشیو 1105 MCU for more than 10 seconds after فتوکپی ریکو آفیشیو 1105 read start signal is sent to فتوکپی ریکو آفیشیو 1105 MCU. Possible Causes
- Poor connection between SICU and MCU
- MCU software error
SC980: HDD Access Error
Definition [B]
Incorrect parameter sent to فتوکپی ریکو آفیشیو 1105 HDD controller.
Possible Causes
- Software defective
- SICU defective
SC982: HDD Construction Error
Definition [B’]
A HDD that does not have فتوکپی ریکو آفیشیو 1105 correct specifications has been installed.
Possible Causes
- HDD defective
- Incorrect HDD type
SC984: HDD 1 Data Transfer Error 1
Definition [B’]
فتوکپی ریکو آفیشیو 1105 data transfer from فتوکپی ریکو آفیشیو 1105 DRAM to HDD 1 is not completed within 15 seconds. Possible Causes
- HDD 1 defective
- SICU defective
- Software defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and HDD 1
SC985: HDD 2 Data Transfer Error 2
Definition [B’]
فتوکپی ریکو آفیشیو 1105 data transfer from فتوکپی ریکو آفیشیو 1105 DRAM to HDD 2 is not completed within 15 seconds. Possible Causes
- HDD 2 defective
- SICU defective
- Software defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and HDD 2
SC986: HDD 1 Data Transfer Error 2
Definition [B’]
فتوکپی ریکو آفیشیو 1105 data transfer from HDD 1 to فتوکپی ریکو آفیشیو 1105 DRAM is not completed within 15 seconds. Possible Causes
- HDD 1 defective
- SICU defective
- Software defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and HDD 1
SC987: HDD 2 Data Transfer Error 2
Definition [B’]
فتوکپی ریکو آفیشیو 1105 data transfer from HDD 2 to فتوکپی ریکو آفیشیو 1105 DRAM is not completed within 15 seconds. Possible Causes
- HDD 2 defective
- SICU defective
- Software defective
- Poor connection between فتوکپی ریکو آفیشیو 1105 SICU and HDD 2
SC990: Software Performance Error
Definition [B’]
فتوکپی ریکو آفیشیو 1105 software performs an unexpected function.
Possible Causes
Software defective