کیو سرا میتا fs6030mfp
0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem copyir.com Defective FAX control PWB copyir.com
0060 Engine PWB type error Defective engine sub PCB copyir.com
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com Defective FAX software
Defective FAX control PWB copyir.com
0100 Backup memory device error Defective flash memory copyir.com
0120 MAC address data error
For data in which the MAC address is invalid copyir.com Defective main PWB copyir.com
Defective flash memory copyir.com
Defective engine PWB copyir.com
0130 Backup memory read/write error (main PWB) Defective flash memory copyir.com
Defective main PWB copyir.com
0140 Backup memory data error (main PWB) Defective flash memory copyir.com
Defective main PWB copyir.com
0150 Backup memory read/write error (engine PWB)
Detecting engine PWB EEPROM communication error copyir.com Improper installation engine PWB EEPROM copyir.com
Defective engine PWB copyir.com
Device damage of EEPROM copyir.com
0160 Backup memory data error (engine PWB) Defective flash memory copyir.com
Defective engine PWB copyir.com
0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters copyir.com Data damage of EEPROM copyir.com
Defective PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM copyir.com
0320 I/O CPU communication error
A communication error is detected 10 times in succession copyir.com Defective PWB copyir.com
0630 DMA error DMA transmission of image data does not complete within the specified period of time copyir.com Poor contact in the connector terminals copyir.com Defective main PWB copyir.com
0800 Image processing error
JAM05 is detected twice copyir.com Defective main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com The battery is disconnected from the main PWB copyir.com
Defective main PWB copyir.com
0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com Improper installation FAX control PWB copyir.com
Defective FAX control PWB or main PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com Defective FAX control PWB copyir.com
1010 Lift motor error
After cassette 1 is inserted, lift sensor does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of the lift motor copyir.com
Defective lift motor copyir.com
Defective engine PWB copyir.com
1020 PF lift motor error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of the PF lift motor 1 copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1030 PF lift motor error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of the PF lift motor 2 copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1800 Paper feeder communication error
A communication error is detected 10 times in succession copyir.com Improper installation paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective PF main PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, the write data and the read data is not continuously in agreement 5 times copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
2000 Main motor steady-state error
Stable OFF is detected for 1 s continuously after main motor stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of the main motor copyir.com
Defective main motor copyir.com
Defective engine PWB copyir.com
2010 Main motor drive error
The main motor is not stabilized within 2 s after driving starts copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of the main motor copyir.com
Defective main motor copyir.com
Defective engine PWB copyir.com
2600 PF drive motor error (paper feeder)
When the PF drive motor is driven, error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of the PF drive motor copyir.com
Defective PF drive motor copyir.com
Defective PF main PWB copyir.com
3100 ISU home position error
The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective home position sensor copyir.com
Defective ISU motor copyir.com
Defective CCD PWB copyir.com
Defective engine PWB copyir.com
3200 Exposure lamp error
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective exposure lamp copyir.com
Defective CCD PWB copyir.com
Defective main PWB copyir.com
3500 Communication error between scanner and ASIC
An error code is detected 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CCD PWB copyir.com
Defective main PWB copyir.com
3600 Scanner sequence error Defective main PWB or engine PWB copyir.com
4000 Polygon motor synchronization error
The polygon motor is not stabilized within 10 s after driving starts copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
4010 Polygon motor steady-state error
Stable OFF is detected for 1 s continuously after polygon motor stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
4100 BD initialization error
BD is not detected within 1 s after polygon motor stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB copyir.com
Defective BD PWB copyir.com
Defective main PWB copyir.com
4700 VIDEO ASIC device error Defective connector cable or poor contact in the connector copyir.com
Defective main PWB or engine PWB copyir.com
6000 Broken fuser heater wire
The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up copyir.com The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109 copyir.com4°F or less copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Broken fuser heater wire copyir.com
Defective engine PWB copyir.com
6000, 6020, 6030, 6050 Broken fuser heater wire
Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature Deformed connector pin copyir.com
Defective triac copyir.com
6020 Abnormally high fuser thermistor temperature
The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms copyir.com High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor copyir.com
Defective engine PWB copyir.com
6030 Broken fuser thermistor wire
A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor copyir.com
Defective engine PWB copyir.com
6050 Abnormally low fuser thermistor temperature
As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6400 Zero-cross signal error
While fuser heater control is performed, the zero-cross signal is not input within 3 s copyir.com Defective connector cable or poor contact in the connector
Defective power source PWB or engine PWB copyir.com
7800 Broken external thermistor wire
The thermistor output value is 0 copyir.com3 V or less copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective temperature sensor copyir.com
7810 Short-circuited external thermistor wire
The thermistor output value is 3 V or more copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective temperature sensor copyir.com
7900 Drum unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum unit copyir.com
7910 Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit copyir.com
8030 Tray upper limit detection problem (document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective tray upper limit sensor, paper surface sensor 1/2 copyir.com
Defective DF main PWB copyir.com
8040 Belt problem (document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective belt sensor copyir.com
Defective belt solenoid copyir.com
Defective DF main PWB copyir.com
8140 Tray elevation motor problem (document finisher)
The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective connector cable or poor contact in the connector copyir.com
The tray elevation motor malfunctions copyir.com
Defective tray lower limit sensor, paper surface sensor 1/2 copyir.com
Defective DF main PWB copyir.com
8210 Stapler problem (document finisher)
Jam 7012 or 7023 is indicated copyir.com Defective connector cable of staple or poor contact in the connector copyir.com
The stapler is blocked with a staple copyir.com
The stapler is broken
Defective DF main PWB copyir.com
8320 Adjustment motor 2 problem (document finisher)
The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective adjustment sensor 2 copyir.com
Defective adjustment motor 2 copyir.com
Defective DF main PWB copyir.com
8330 Adjustment motor 1 problem (document finisher)
The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective adjustment sensor 1 copyir.com
Defective adjustment motor 1 copyir.com
8350 Roller motor problem (document finisher)
The roller sensor does not turn on/off within specified time of the roller motor turning on copyir.com Defective DF main PWB copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective roller sensor copyir.com
Defective roller motor copyir.com
Defective DF main PWB copyir.com
8360 Slide motor problem (document finisher)
The slide sensor does not turn on/off within specified time of the slide motor turning on copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective slide sensor copyir.com
Defective slide motor copyir.com
Defective DF main PWB copyir.com
8460 EEPROM problem (document finisher)
Reading from or writing to EEPROM cannot be performed copyir.com Defective EEPROM or DF main PWB copyir.com
8800 Document finisher communication error
A communication error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector
Defective DF main PWB copyir.com
Defective engine PWB copyir.com
8830 Bridge communication error (document finisher)
A communication error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective bridge PWB copyir.com
Defective engine PWB copyir.com
8990 Document finisher communication error Defective connector cable or poor contact in the connector copyir.com
Defective DF main PWB copyir.com
Defective bridge PWB copyir.com
9000 Document processor communication error
A communication error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP main PWB copyir.com
9060 DP EEPROM error Read and write data does not match copyir.com Data in the specified area of the backup memory does not match the specified values copyir.com Defective DP main PWB copyir.com
Device damage of EEPROM copyir.com
9500 BRU communication error IPU PWB error
9510 BRU PWB error IPU PWB error
9520 BRU PWB data error IPU PWB error
9530 Machine No copyir.combackup error C IPU PWB error
9540 Machine No copyir.combackup error D IPU PWB error
9550 Machine No copyir.combackup error E IPU PWB error
F000 Main PWB – operation panel PWB communication error Defective main PWB copyir.com
Defective operation panel PWB copyir.com
F010, F011, F012, F013 Main PWB checksum error Defective main PWB copyir.com
F040 Main PWB – print engine communication error Defective main PWB copyir.com
Defective engine PWB copyir.com
F050 Print engine ROM checksum error Defective engine PWB copyir.com