کیو سرا میتا fs6020

کیو سرا میتا fs6020

0420    serial communication error between paper feeder and engine/high voltage PWB     copyir     copyir.comcom
• Communication ready signal time     copyir     copyir.comcomout occurs continuously more than specified times in serial communication with an optional paper feeder that is recognized by the CPU on the engine/high voltage PWB     copyir     copyir.comcom • Inconsistency of values in serial communication data occurs more than specified times     copyir     copyir.comcom
1210    duplexer slide guide home position detection error     copyir     copyir.comcom
• The duplexer drive PWB of the optional duplexer cannot detect the home position of the slide guide     copyir     copyir.comcom
2000    main motor error
• The main motor ready signal (MOTRDYN) does not become ready (low level) a specified time after the main motor drive signal (MOTONN) is turned on     copyir     copyir.comcom • The main motor ready signal (MOTRDYN) does not become ready (low level) a specified time after the main motor drive signal (MOTONN) is turned off     copyir     copyir.comcom
2610    paper feeder 1 feed motor error     copyir     copyir.comcom
• When the paper feeder drive PWB of the optional paper feeder 1 drives the feed motor     copyir     copyir.comcom no proper clock pulse is input from the feed motor clock sensor     copyir     copyir.comcom
2620    paper feeder 2 feed motor error
• When the paper feeder drive PWB of the optional paper feeder 2 drives the feed motor     copyir     copyir.comcom no proper clock pulse is input from the feed motor clock sensor     copyir     copyir.comcom
2630    paper feeder 3 feed motor error
• When the paper feeder drive PWB of the optional paper feeder 3 drives the feed motor     copyir     copyir.comcom no proper clock pulse is input from
2640    paper feeder 4 feed motor error
• When the paper feeder drive PWB of the optional paper feeder 4 drives the feed motor     copyir     copyir.comcom no proper clock pulse is input from the feed motor clock sensor     copyir     copyir.comcom
4000    polygon motor error
• The polygon motor ready signal (MOTRDYN) does not become ready (L level) within a specified time after the polygon motor drive signal (POLONN) is turned on (L level)     copyir     copyir.comcom
4200    laser output error
• The pin photo signal (PDN) is not output within a specified time after the polygon motor ready signal (MOTRDYN) becomes ready (L level)     copyir     copyir.comcom
6000    fixing heater lamp/fixing thermistor error
• The fixing thermistor disconnection detection circuit in the engine/high voltage PWB outputs the disconnection detection signal (THDEAD) to the CPU more than a specified time after power is turned on     copyir     copyir.comcom • The fixing temperature does not rise at least 1 °C when the fixing heater lamp is continuously on for approximately 20 seconds during printer warm     copyir     copyir.comcomup or in the standby mode     copyir     copyir.comcom • The fixing temperature does not rise at least 1 °Cwhen the fixing heater lamp is continuously on for approximately 15 seconds during printing     copyir     copyir.comcom • The fixing temperature does not lower when the fixing heater lamp is off for a specified time or more     copyir     copyir.comcom * The fixing temperature is the average value calculated using the input voltage from the fixing thermistor detected several times in a specified time to avoid influence of noise and so on     copyir     copyir.comcom
6020    abnormally high fixing temperature error
• The fixing heater lamp runaway protection circuit in the engine/high voltage PWB outputs continuously the abnormally high temperature detection signal (HTEMPN) to the CPU for a longer time than specified     copyir     copyir.comcom
6400    fixing heater lamp control zero     copyir     copyir.comcomcross signal detection error
• The zero     copyir     copyir.comcomcross signal (ZCROSS) that is output from the power source PWB and input to the CPU on the engine/high voltage PWB is not input for a specified time     copyir     copyir.comcom
F0    communication error between the operation panel PWB and main PWB
• Serial communication between the operation panel PWB and the main PWB malfunctions     copyir     copyir.comcom{
F010    code ROM checksum error
• Checksum of the code ROM PWB attached to the socket (YS1) on the main PWB malfunctions     copyir     copyir.comcom
F020    main PWB RAM checksum errorion error
Checksum in the standard RAM mounted on the main PWB or in optional expansion memory is not correct     copyir     copyir.comcom {
F030    main PWB controller errororion error
• The controller (CPU) on the main PWB malfunctions     copyir     copyir.comcom
F040    communication error between engine/high voltage PWB and main PWB controller
• Communication between the CPU on the engine/high voltage PWB and the controller (CPU) on the main PWB malfunctions     copyir     copyir.comcom
F050    engine/high     copyir     copyir.comcomvoltage flash memory checksum error     copyir     copyir.comcom
• Checksum of the program built in the CPU on the engine/high voltage PWB is not correct     copyir     copyir.comcom
F080    system firmware download error
• Checksum is not correct when system firmware is downloaded     copyir     copyir.comcom • The flash memory is empty     copyir     copyir.comcom