کیو سرا میتا fs6025mfp

کیو سرا میتا fs6025mfp

0030    FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem     copyir.com    Defective FAX control PWB     copyir.com
0060    Engine PWB type error    Defective engine sub PCB     copyir.com
0070    FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted     copyir.com    Defective FAX software
Defective FAX control PWB     copyir.com
0100    Backup memory device error    Defective flash memory     copyir.com
0120    MAC address data error
For data in which the MAC address is invalid     copyir.com    Defective main PWB     copyir.com
Defective flash memory     copyir.com
Defective engine PWB     copyir.com
0130    Backup memory read/write error (main PWB)    Defective flash memory     copyir.com
Defective main PWB     copyir.com
0140    Backup memory data error (main PWB)    Defective flash memory     copyir.com
Defective main PWB     copyir.com
0150    Backup memory read/write error (engine PWB)
Detecting engine PWB EEPROM communication error     copyir.com    Improper installation engine PWB EEPROM     copyir.com
Defective engine PWB     copyir.com
Device damage of EEPROM     copyir.com
0160    Backup memory data error (engine PWB)    Defective flash memory     copyir.com
Defective engine PWB     copyir.com
0170    Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters     copyir.com    Data damage of EEPROM     copyir.com
Defective PWB     copyir.com
0180    Machine number mismatch
Machine number of main and engine does not match     copyir.com    Data damage of EEPROM     copyir.com
0320    I/O CPU communication error
A communication error is detected 10 times in succession     copyir.com    Defective PWB     copyir.com
0630    DMA error DMA transmission of image data does not complete within the specified period of time     copyir.com    Poor contact in the connector terminals     copyir.com Defective main PWB     copyir.com
0800    Image processing error
JAM05 is detected twice     copyir.com    Defective main PWB     copyir.com
0830    FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB     copyir.com    Defective FAX software     copyir.com
Defective FAX control PWB     copyir.com
0840    Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed     copyir.com    The battery is disconnected from the main PWB     copyir.com
Defective main PWB     copyir.com
0870    FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times     copyir.com    Improper installation FAX control PWB     copyir.com
Defective FAX control PWB or main PWB     copyir.com
0920    Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB     copyir.com    Defective FAX control PWB     copyir.com
1010    Lift motor error
After cassette 1 is inserted, lift sensor does not turn on within 12 s     copyir.com This error is detected four times successively     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of the lift motor     copyir.com
Defective lift motor     copyir.com
Defective engine PWB     copyir.com
1020    PF lift motor error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s     copyir.com This error is detected four times successively     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of the PF lift motor 1     copyir.com
Defective PF lift motor 1     copyir.com
Defective PF main PWB     copyir.com
1030    PF lift motor error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s     copyir.com This error is detected four times successively     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of the PF lift motor 2     copyir.com
Defective PF lift motor 2     copyir.com
Defective PF main PWB     copyir.com
1800    Paper feeder communication error
A communication error is detected 10 times in succession     copyir.com    Improper installation paper feeder     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective engine PWB     copyir.com
Defective PF main PWB     copyir.com
1900    Paper feeder EEPROM error
When writing the data, the write data and the read data is not continuously in agreement 5 times     copyir.com    Defective PF main PWB     copyir.com
Device damage of EEPROM     copyir.com
2000    Main motor steady-state error
Stable OFF is detected for 1 s continuously after main motor stabilized     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of the main motor     copyir.com
Defective main motor     copyir.com
Defective engine PWB     copyir.com
2010    Main motor drive error
The main motor is not stabilized within 2 s after driving starts     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of the main motor     copyir.com
Defective main motor     copyir.com
Defective engine PWB     copyir.com
2600    PF drive motor error (paper feeder)
When the PF drive motor is driven, error signal is detected continuously for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of the PF drive motor     copyir.com
Defective PF drive motor     copyir.com
Defective PF main PWB     copyir.com
3100    ISU home position error
The home position is not correct when the power is turned on or at the start of copying using the table     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective home position sensor     copyir.com
Defective ISU motor     copyir.com
Defective CCD PWB     copyir.com
Defective engine PWB     copyir.com
3200    Exposure lamp error
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective exposure lamp     copyir.com
Defective CCD PWB     copyir.com
Defective main PWB     copyir.com
3500    Communication error between scanner and ASIC
An error code is detected 3 times in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective CCD PWB     copyir.com
Defective main PWB     copyir.com
3600    Scanner sequence error    Defective main PWB or engine PWB     copyir.com
4000    Polygon motor synchronization error
The polygon motor is not stabilized within 10 s after driving starts     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective polygon motor     copyir.com
Defective engine PWB     copyir.com
4010    Polygon motor steady-state error
Stable OFF is detected for 1 s continuously after polygon motor stabilized     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective polygon motor     copyir.com
Defective engine PWB     copyir.com
4100    BD initialization error
BD is not detected within 1 s after polygon motor stabilized     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective APC PWB     copyir.com
Defective BD PWB     copyir.com
Defective main PWB     copyir.com
4700    VIDEO ASIC device error    Defective connector cable or poor contact in the connector     copyir.com
Defective main PWB or engine PWB     copyir.com
6000    Broken fuser heater wire
The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up     copyir.com The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109     copyir.com4°F or less     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Deformed connector pin     copyir.com
Defective triac     copyir.com
Fuser thermostat triggered     copyir.com
Broken fuser heater wire     copyir.com
Defective engine PWB     copyir.com
6000, 6020, 6030, 6050    Broken fuser heater wire
Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature    Deformed connector pin     copyir.com
Defective triac     copyir.com
6020    Abnormally high fuser thermistor temperature
The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms     copyir.com High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms     copyir.com    Deformed connector pin     copyir.com
Defective triac     copyir.com
Shorted fuser thermistor     copyir.com
Defective engine PWB     copyir.com
6030    Broken fuser thermistor wire
A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Deformed connector pin     copyir.com
Defective triac     copyir.com
Defective fuser thermistor     copyir.com
Defective engine PWB     copyir.com
6050    Abnormally low fuser thermistor temperature
As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second     copyir.com    Deformed connector pin     copyir.com
Defective triac     copyir.com
Defective fuser thermistor
Defective fuser heater     copyir.com
Defective engine PWB     copyir.com
6400    Zero-cross signal error
While fuser heater control is performed, the zero-cross signal is not input within 3 s     copyir.com    Defective connector cable or poor contact in the connector
Defective power source PWB or engine PWB     copyir.com
7800    Broken external thermistor wire
The thermistor output value is 0     copyir.com3 V or less     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective temperature sensor     copyir.com
7810    Short-circuited external thermistor wire
The thermistor output value is 3 V or more     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective temperature sensor     copyir.com
7900    Drum unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs eight times successively     copyir.com Mismatch between writing data and reading data occurs eight times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drum unit     copyir.com
7910    Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs eight times successively     copyir.com Mismatch between writing data and reading data occurs eight times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective developer unit     copyir.com
8030    Tray upper limit detection problem (document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective tray upper limit sensor, paper surface sensor 1/2     copyir.com
Defective DF main PWB     copyir.com
8040    Belt problem (document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective belt sensor     copyir.com
Defective belt solenoid     copyir.com
Defective DF main PWB     copyir.com
8140    Tray elevation motor problem (document finisher)
The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
The tray elevation motor malfunctions     copyir.com
Defective tray lower limit sensor, paper surface sensor 1/2     copyir.com
Defective DF main PWB     copyir.com
8210    Stapler problem (document finisher)
Jam 7012 or 7023 is indicated     copyir.com    Defective connector cable of staple or poor contact in the connector     copyir.com
The stapler is blocked with a staple     copyir.com
The stapler is broken
Defective DF main PWB     copyir.com
8320    Adjustment motor 2 problem (document finisher)
The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective adjustment sensor 2     copyir.com
Defective adjustment motor 2     copyir.com
Defective DF main PWB     copyir.com
8330    Adjustment motor 1 problem (document finisher)
The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective adjustment sensor 1     copyir.com
Defective adjustment motor 1     copyir.com
8350    Roller motor problem (document finisher)
The roller sensor does not turn on/off within specified time of the roller motor turning on     copyir.com    Defective DF main PWB     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective roller sensor     copyir.com
Defective roller motor     copyir.com
Defective DF main PWB     copyir.com
8360    Slide motor problem (document finisher)
The slide sensor does not turn on/off within specified time of the slide motor turning on     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective slide sensor     copyir.com
Defective slide motor     copyir.com
Defective DF main PWB     copyir.com
8460    EEPROM problem (document finisher)
Reading from or writing to EEPROM cannot be performed     copyir.com    Defective EEPROM or DF main PWB     copyir.com
8800    Document finisher communication error
A communication error is detected 10 times in succession     copyir.com    Defective connector cable or poor contact in the connector
Defective DF main PWB     copyir.com
Defective engine PWB     copyir.com
8830    Bridge communication error (document finisher)
A communication error is detected 10 times in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective bridge PWB     copyir.com
Defective engine PWB     copyir.com
8990    Document finisher communication error    Defective connector cable or poor contact in the connector     copyir.com
Defective DF main PWB     copyir.com
Defective bridge PWB     copyir.com
9000    Document processor communication error
A communication error is detected 10 times in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective DP main PWB     copyir.com
9060    DP EEPROM error Read and write data does not match     copyir.com Data in the specified area of the backup memory does not match the specified values     copyir.com    Defective DP main PWB     copyir.com
Device damage of EEPROM     copyir.com
9500    BRU communication error    IPU PWB error
9510    BRU PWB error    IPU PWB error
9520    BRU PWB data error    IPU PWB error
9530    Machine No     copyir.combackup error C    IPU PWB error
9540    Machine No     copyir.combackup error D    IPU PWB error
9550    Machine No     copyir.combackup error E    IPU PWB error
F000    Main PWB – operation panel PWB communication error    Defective main PWB     copyir.com
Defective operation panel PWB     copyir.com
F010, F011, F012, F013    Main PWB checksum error    Defective main PWB     copyir.com
F040    Main PWB – print engine communication error    Defective main PWB     copyir.com
Defective engine PWB     copyir.com
F050    Print engine ROM checksum error    Defective engine PWB     copyir.com