لمینت MKP
1402-06-04
Menu
195 Serial Number Error
The serial number stored in the memory (EGB) is not correct copyir.com EEPROM defective copyir.com EGB replaced without original EEPROM 1 copyir.com Check the serial number copyir.com 2 copyir.com If the stored serial number is incorrect, contact your supervisor copyir.com
202 Polygon motor error 1: ON timeout
The polygon mirror motor does not reach the targeted operating speed within 5 sec copyir.com after turning on or changing speed
203 Polygon motor error 2: OFF timeout
The polygon mirror motor does not leave the READY status within 3 sec copyir.com after the polygon motor switched off copyir.com
204 Polygon motor error 3: XSCRDY signal error
The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing copyir.com Polygon motor/driver board harness loose or disconnected copyir.com Polygon motor/driver board defective copyir.com Laser optics unit defective copyir.com IPU (EGB) defective 1 copyir.com Replace the interface harness of the laser optics unit copyir.com 2 copyir.com Replace the laser optics unit copyir.com 3 copyir.com Replace the EGB (Engine Board) copyir.com
220 Laser Synchronizing Detection Error: [K]/[Y]
The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally copyir.com
222 Laser Synchronizing Detection Error: [M]/[C]
The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally copyir.com Disconnected cable from the laser synchronizing detection unit or defective connection copyir.com Defective laser synchronizing detector copyir.com Defective LDB copyir.com copyir.com Defective EGB 1 copyir.com Check the connectors copyir.com 2 copyir.com Replace the laser optics unit copyir.com 3 copyir.com Replace the EGB copyir.com
240 LD error
The IPU (EGB) detects a problem at the LD unit copyir.com Worn-out LD copyir.com Disconnected or broken harness of the LD copyir.com 1 copyir.com Replace the laser optics unit copyir.com
300 High voltage power output error
The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit) copyir.com Disconnected or defective high voltage harness copyir.com Defective high voltage power supply copyir.com Defective EGB 1 copyir.com Check or replace the harnesses copyir.com 2 copyir.com Replace the high voltage power supply board 3 copyir.com Replace the EGB copyir.com
396 Black drum motor error
The LOCK signal error is detected when the EGB monitors the black drum motor state copyir.com (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops copyir.com) Disconnected or defective motor harness copyir.com Motor slips due to excessive load 1 copyir.com Check the harness from the black drum motor copyir.com Replace it if necessary copyir.com
397 Color drum motor error
The LOCK signal error is detected when the EGB monitors the color drum motor state copyir.com (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops copyir.com) Disconnected or defective motor harness copyir.com Motor slips due to excessive load 1 copyir.com Check the harness from the color drum motor copyir.com Replace it if necessary copyir.com
445 ITB (Image Transfer Belt) Unit: Home Position Error
The ITB contact sensor does not detect the home position of the ITB for 5 seconds after the ITB unit initialization has been done copyir.com ITB (Image Transfer Belt) Unit: Contact Position Error The ITB contact sensor does not detect the contact position of the ITB for 5 seconds after the ITB unit has moved to the contact position copyir.com ITB (Image Transfer Belt) Unit: No-contact Position Error The ITB contact sensor does not detect the home position of the ITB for 5 seconds after the ITB unit has moved to no-contact position copyir.com- Defective ITB contact motor copyir.com Defective ITB contact sensor copyir.com Defective ITB unit 1 copyir.com Replace the ITB contact motor copyir.com 2 copyir.com Replace the ITB contact sensor copyir.com 3 copyir.com Replace the ITB unit copyir.com
480 Agitator Motor Error
The agitator motor error is detected twice for 10 msec during the initialization at power-on or after the cover is closed copyir.com Disconnected or defective harness copyir.com Defective agitator motor 1 copyir.com Check or replace the harness copyir.com 2 copyir.com Replace the agitator motor copyir.com
490 ITB (Image Transfer Belt) Unit Set Error
The TM sensor does not detect the reflection from the ITB copyir.com No ITB unit in the machine copyir.com Dirty TM sensor 1 copyir.com Check the installation of the ITB unit copyir.com 2 copyir.com Clean the TM sensor copyir.com
500 Transport/Fusing Motor Error
The LOCK signal error is detected when the EGB monitors the transport/fusing motor state copyir.com (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops copyir.com) Disconnected or defective motor harness copyir.com Motor slips due to excessive load 1 copyir.com Check the harness from the transport/fusing motor copyir.com Replace it if necessary copyir.com
530 LSU Fan Motor Error
A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued copyir.com Disconnected or defective motor harness copyir.com Defective LSU fan motor 1 copyir.com Check or replace the motor harness copyir.com 2 copyir.com Replace the LSU fan motor copyir.com
531 Fusing Fan Motor Error
A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued copyir.com Disconnected or defective motor harness copyir.com Defective LSU fan motor 1 copyir.com Check or replace the motor harness copyir.com 2 copyir.com Replace the fusing fan motor copyir.comit
541 Thermistor Error
The thermistor output is less than 0°C for 7 seconds copyir.com Disconnected thermistor copyir.com Defective harness connection 1 copyir.com Check the harness connection of the thermistor copyir.com 2 copyir.com Replace the fusing unit copyir.com Execute “Engine Maintenance Menu” to recover the machine after completing the recovery procedure copyir.com Otherwise, the machine continues to issue this SC code and cannot be operated copyir.com
542 Print Ready Temperature Error
The heating roller temperature increase during a set time is not correct copyir.com The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on copyir.com Defective thermistor copyir.com Incorrect power supply input at the main power socket copyir.com Defective fusing lamp 1 copyir.com Check the voltage of the wall outlet copyir.com 2 copyir.com Replace the fusing unit 3 copyir.com Replace the fusing lamp copyir.com Execute “Engine Maintenance Menu” to recover the machine after completing the recovery procedure copyir.com Otherwise, the machine continues to issue this SC code and cannot be operated copyir.com
543 High Temperature Detection Error
This SC is issued if one of following conditions occurs copyir.com The thermistor (center) detects 255°C or thermistor (end) detects 245°C copyir.com The thermistor (center) detects a 3°C increment or more for five seconds at 220°C or more or the thermistor (end) detects a 4°C increment or more for five seconds at 210°C or more copyir.com Defective I/O control (EGB) copyir.com Defective EGB 1 copyir.com Replace the EGB copyir.com Execute “Engine Maintenance Menu” to recover the machine after completing the recovery procedure copyir.com Otherwise, the machine continues to issue this SC code and cannot be operated copyir.com
545 Heating Lamp Full-Power Error
The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating copyir.com Deformed thermistor copyir.com Thermistor not in the correct position copyir.com Defective fusing lamp 1 copyir.com Replace the fusing unit copyir.com 2 copyir.com Replace the fusing lamp copyir.com Execute “Engine Maintenance Menu” to recover the machine after completing the recovery procedure copyir.com Otherwise, the machine continues to issue this SC code and cannot be operated copyir.com
547 Zero Cross Error
The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door copyir.com Defective fusing lamp relay 1 copyir.com Turn the main power switch off and on copyir.com Execute “Engine Maintenance Menu” to recover the machine after completing the recovery procedure copyir.com Otherwise, the machine continues to issue this SC code and cannot be operated copyir.com
548 Low Temperature Error
The center thermistor detects 100°C or less for 4 seconds copyir.com Defective fusing lamp copyir.com Defective thermistor 1 copyir.com Replace the fusing unit copyir.com 2 copyir.com Replace the fusing lamp copyir.com Execute “Engine Maintenance Menu” to recover the machine after completing the recovery procedure copyir.com Otherwise, the machine continues to issue this SC code and cannot be operated copyir.com
557 Zero Cross Frequency Error
The detection error occurs ten times consecutively in ten zero cross signal detections copyir.com This error is defined when the detected zero cross signal is 17 or less/27 or more for 0 copyir.com2 seconds copyir.com Defective fusing lamp relay copyir.com Unstable input power source 1 copyir.com Check the power supply source copyir.com 2 copyir.com Replace the fusing unit copyir.com Execute “Engine Maintenance Menu” to recover the machine after completing the recovery procedure copyir.com Otherwise, the machine continues to issue this SC code and cannot be operated copyir.com
559 Consecutive Fusing Jame
The paper jam counter for the fusing unit reaches 3 copyir.com The paper jam counter is cleared if the paper is fed correctly copyir.com This SC is activated only when this function is enabled with “Engine Maintenance” (default “OFF”) copyir.com Defective fusing unit copyir.com Defective fusing control 1 copyir.com Clear this SC to send a command after a jam removal copyir.com 2 copyir.com Turn off this function after a jam removal copyir.com Execute “Engine Maintenance Menu” to recover the machine after completing the recovery procedure copyir.com Otherwise, the machine continues to issue this SC code and cannot be operated copyir.comc
669 EEPROM Error
An unexpected value exists in the initialization flag of the EEPROM EEPROM not initialized copyir.com Defective EEPROM 1 copyir.com Initialize the EEPROM copyir.com 2 copyir.com Replace the EEPROM copyir.com 3 copyir.com Replace the EGB copyir.com
690 GAVD Communication Error
The ID of the GAVD is not identified during initialization copyir.com The chip ID of the GAVD cannot be detected by the machine at power-on copyir.com Defective EGB 1 copyir.com Replace the EGB copyir.com
819 Service Cycle Power
Incorrect combination of EGB and controller board copyir.com An unexpected error occurs in the EEPROM on the controller board copyir.com Controller board defective 1 copyir.com Install the correct EGB and controller boards for this machine copyir.com 2 copyir.com Replace the controller board
823 USB/ Network Device Error
An interface error in the USB connection or NIB connection occurs copyir.com Controller board detective 1 copyir.com Replace the controller board copyir.com
824 EEPROM Error
An EEPROM check error at power-on occurs copyir.com Controller board detective 1 copyir.com Replace the controller board copyir.com
827 On-Board Memory Check Error
An on-board memory check error at power-on occurs copyir.com Controller board detective 1 copyir.com Replace the controller board copyir.com
828 ROM Checksum Error
A ROM checksum error at power-on occurs copyir.com 1 copyir.com Replace the controller board copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.