کیو سرا میتا fsc2026mfp plus
0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem copyir.com Defective FAX control PWB copyir.com
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com Defective FAX software copyir.comPWB copyir.com Defective FAX control PWB copyir.com
0100 Backup memory device error Defective flash memory copyir.com Defective main PWB copyir.com
0120 MAC address data error
For data in which the MAC address is invalid copyir.com Defective flash memory copyir.com Defective engine PWB copyir.com
0130 Backup memory read/write error (main PWB) Defective flash memory copyir.com Defective main PWB copyir.com
0140 Backup memory data error (main PWB) Defective flash memory copyir.com Defective main PWB copyir.com
0150 Engine PWB EEPROM error
Detecting engine PWB EEPROM communication error copyir.com Improper installation engine PWB EEPROM copyir.com Defective engine PWB copyir.com Device damage of EEPROM copyir.com
0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters copyir.com Data damage of EEPROM copyir.com Defective PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM copyir.com
0600 Expanded memory (DIMM) installing error
The expansion memory modules (DIMM) are not correctly mounted copyir.com Improper installation expanded memory (DIMM) copyir.com
0610 Expanded memory (DIMM) error
The expansion memory modules (DIMM) mounted on the main PWB does not operate correctly copyir.com Defective expanded memory (DIMM) copyir.com Defective main PWB copyir.com
0640 Hard disk error
The hard disk cannot be accessed copyir.com Defective hard disk copyir.com Defective main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com Defective FAX software copyir.com Defective FAX control PWB copyir.com
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com The battery is disconnected from the main PWB copyir.com Defective main PWB copyir.com
0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com Improper installation FAX control PWB copyir.com Defective FAX control PWB or main PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com Defective FAX control PWB copyir.com
0930 EEPROM bus error Defective drum PWB (EEPROM) copyir.com Defective engine PWB (EEPROM) copyir.com Defective engine PWB copyir.com Defective main PWB copyir.com
1010 Lift motor error
When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals copyir.com After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s copyir.com The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the lift motor copyir.com Defective lift motor copyir.com Defective engine PWB copyir.com
1020 PF lift motor error (paper feeder 1)
When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals copyir.com After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s copyir.com The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the PF lift motor copyir.com Defective PF lift motor copyir.com Defective PF main PWB copyir.com
1030 PF lift motor error (paper feeder 2)
When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals copyir.com After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s copyir.com The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the PF lift motor copyir.com Defective PF lift motor copyir.com Defective PF main PWB copyir.com
1500 PF heater 1 high temperature error (paper feeder 1)
A temperature higher than 75C/167F is detected copyir.com Defective connector cable or poor contact in the connector copyir.com Shorted PF thermistor 1 copyir.com Defective PF fan motor 1 copyir.com Defective PF main PWB copyir.com
1510 PF heater 2 high temperature error (paper feeder 1)
A temperature higher than 75C/167F is detected copyir.com Defective connector cable or poor contact in the connector copyir.com Shorted PF thermistor 2 copyir.com Defective PF fan motor 2 copyir.com Defective PF main PWB copyir.com
1520 PF heater 1 high temperature error (paper feeder 2)
A temperature higher than 75aC/167F is detected copyir.com Defective connector cable or poor contact in the connector copyir.com Shorted PF thermistor 1 copyir.com Defective PF fan motor 1 copyir.com Defective PF main PWB copyir.com
1530 PF heater 2 high temperature error (paper feeder 2)
A temperature higher than 75C/167F is detected copyir.com Defective connector cable or poor contact in the connector copyir.com Shorted PF thermistor 2 copyir.com Defective PF fan motor 2 copyir.com Defective PF main PWB copyir.com
1600 PF heater 1 low temperature error (paper feeder 1)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on copyir.com Defective connector cable or poor contact in the connector copyir.com PF thermistor 1 installed incorrectly copyir.com Defective PF thermistor 1 copyir.com Broken PF heater 1 copyir.com Defective PF heater PWB or PF main PWB copyir.com
1610 PF heater 2 low temperature error (paper feeder 1)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on copyir.com Defective connector cable or poor contact in the connector copyir.com PF thermistor 2 installed incorrectly copyir.com Defective PF thermistor 2 copyir.com Broken PF heater 2 copyir.com Defective PF heater PWB or PF main PWB copyir.com
1620 PF heater 1 low temperature error (paper feeder 2)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on copyir.com Defective connector cable or poor contact in the connector copyir.com PF thermistor 1 installed incorrectly copyir.com Defective PF thermistor 1 copyir.com Broken PF heater 1 copyir.com Defective PF heater PWB or PF main PWB copyir.com
1630 PF heater 2 low temperature error (paper feeder 2)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on copyir.com Defective connector cable or poor contact in the connector copyir.com PF thermistor 2 installed incorrectly copyir.com Defective PF thermistor 2 copyir.com Broken PF heater 2 copyir.com Defective PF heater PWB or PF main PWB copyir.com
1800 Paper feeder communication error
Communication error between engine PWB and optional paper feeder copyir.com Improper installation paper feeder copyir.com Defective connector cable or poor contact in the connector copyir.com Defective engine PWB copyir.com Defective PF main PWB copyir.com
2100 Developing motor error
The developing motor ready input is not given for 5 s during the main motor is ON copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the developing motor copyir.com Defective developing motor copyir.com Defective engine PWB copyir.com
2200 Drum motor error
The drum motor ready input is not given for 5 s during the drum motor is ON copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the drum motor copyir.com Defective drum motor copyir.com Defective engine PWB copyir.com
2330 Fuser pressure release motor error
When the fuser pressure release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the fuser pressure release motor copyir.com Defective fuser pressure release motor copyir.com Defective engine PWB copyir.com
2340 Fuser pressure release motor time-out error
When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6 s copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the fuser pressure release motor copyir.com Defective fuser pressure release motor copyir.com Defective engine PWB copyir.com
2500 Paper feed motor error
The drum motor ready input is not given for 5 s during the paper feed motor is ON copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the paper feed motor copyir.com Defective paper feed motor copyir.com Defective engine PWB copyir.com
2600 PF paper feed motor error (paper feeder 1)
The drum motor ready input is not given for 2 s during the PF paper feed motor is ON copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the PF paper feed motor copyir.com Defective PF paper feed motor copyir.com Defective PF main PWB copyir.com
2610 PF paper feed motor error (paper feeder 2)
The drum motor ready input is not given for 2 s during the PF paper feed motor is ON copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the PF paper feed motor copyir.com Defective PF paper feed motor copyir.com Defective PF main PWB copyir.com
2730 Developing release motor error
When the developing release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the developing release motor copyir.com Defective developing release motor copyir.com Defective engine PWB copyir.com
2740 Developing release motor time-out error
When the developing release motor is driven, the developing release switch (DEVRSW) is not detectable for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the developing release motor copyir.com Defective developing release motor copyir.com Defective engine PWB copyir.com
2820 Fuser motor error
The fuser motor ready input is not given for 5 s during the fuser motor is ON copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the fuser motor copyir.com Defective fuser motor copyir.com Defective engine PWB copyir.com
3100 ISU home position error
The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Defective connector cable or poor contact in the connector copyir.com Defective home position sensor copyir.com Defective ISU motor copyir.com Defective CCD PWB copyir.com Defective main PWB copyir.com
3200 Exposure lamp error
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com Defective exposure lamp copyir.com Defective inverter PWB or CCD PWB copyir.com Defective main PWB copyir.com
3300 AGC error
After AGC, correct input is not obtained at CCD copyir.com Defective connector cable or poor contact in the connector copyir.com Defective exposure lamp copyir.com Defective inverter PWB or CCD PWB copyir.com Defective main PWB copyir.com
3500 Communication error between scanner and ASIC
An error code is detected copyir.com Defective connector cable or poor contact in the connector copyir.com Defective CCD PWB copyir.com Defective main PWB copyir.com
4001 Polygon motor KM error
The polygon motor KM ready input is not given for 10 s during the polygon motor is ON copyir.com Defective connector cable or poor contact in the connector copyir.com Defective polygon motor KM copyir.com Defective engine PWB copyir.com
4002 Polygon motor CY error
The polygon motor CY ready input is not given for 10 s during the polygon motor is ON copyir.com Defective connector cable or poor contact in the connector copyir.com Defective polygon motor CY copyir.com Defective engine PWB copyir.com
4201 Laser output error (black)
The pin photo signal is not output from PD PWB K for one second while laser is emitted copyir.com Defective connector cable or poor contact in the connector copyir.com Defective APC PWB K copyir.com Defective PD PWB K copyir.com Defective engine PWB copyir.com
4202 Laser output error (cyan)
The pin photo signal is not output from PD PWB C for one second while laser is emitted copyir.com Defective connector cable or poor contact in the connector copyir.com Defective APC PWB C copyir.com Defective PD PWB C copyir.com Defective engine PWB copyir.com
4203 Laser output error (magenta)
The pin photo signal is not output from PD PWB M for one second while laser is emitted copyir.com Defective connector cable or poor contact in the connector copyir.com Defective APC PWB M copyir.com Defective PD PWB M copyir.com Defective engine PWB copyir.com
4204 Laser output error (yellow)
The pin photo signal is not output from PD PWB Y for one second while laser is emitted copyir.com Defective connector cable or poor contact in the connector copyir.com Defective APC PWB Y copyir.com Defective PD PWB Y copyir.com Defective engine PWB copyir.com
4600 LSU cleaning motor error
When the LSU cleaning motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the LSU cleaning motor copyir.com Defective LSU cleaning motor copyir.com Defective engine PWB copyir.com
4700 VIDEO ASIC device error Defective connector cable or poor contact in the connector copyir.com Defective main PWB or engine PWB copyir.com
5301 Broken cleaning lamp K wire
When the cleaning lamp K is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective cleaning lamp K copyir.com Defective engine PWB copyir.com
5302 Broken cleaning lamp C wire
When the cleaning lamp C is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective cleaning lamp C copyir.com Defective engine PWB copyir.com
5303 Broken cleaning lamp M wire
When the cleaning lamp M is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective cleaning lamp M copyir.com Defective engine PWB copyir.com
5304 Broken cleaning lamp Y wire
When the cleaning lamp Y is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective cleaning lamp Y copyir.com Defective engine PWB copyir.com
6000 Broken fuser heater wire
The detected temperature of fuser thermistor does not rise 1„aC/1 copyir.com8„aF after the fuser heater has been turned on continuously for 10 s in warming up copyir.com The fuser temperature does not reach 100„aC/212„aF after the fuser heater has been turned on continuously for 30 s in warming up copyir.com The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up copyir.com The detected temperature of fuser thermistor does not rise 1„aC/1 copyir.com8„aF after the fuser heater has been turned on continuously for 10 s during printing copyir.com Defective connector cable or poor contact in the connector copyir.com Fuser thermostat triggered copyir.com Broken fuser heater wire copyir.com Defective engine PWB copyir.com
6020 Abnormally high fuser thermistor temperature
The fuser thermistor detects a temperature higher than 240C/464F copyir.com By the activation of the high temperature error detection circuit (230C/446F or more) of fuser thermistor, the illumination of fuser heater was forcibly turned off and 10 s has elapsed copyir.com Shorted fuser thermistor copyir.com Defective engine PWB copyir.com
6030 Broken fuser thermistor wire
Input from fuser thermistor is 3 or less (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com Broken fuser thermistor wire copyir.com Fuser thermostat triggered copyir.com Broken fuser heater wire copyir.com Defective engine PWB copyir.com
6400 Zero-cross signal error
The zero-cross signal does not reach the engine PWB for more than 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com Defective power source PWB or engine PWB copyir.com
7001 Toner motor K error
When the toner motor K is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the toner motor K copyir.com Defective toner motor K copyir.com Defective engine PWB copyir.com
7002 Toner motor C error
When the toner motor C is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the toner motor C copyir.com Defective toner motor C copyir.com Defective engine PWB copyir.com
7003 Toner motor M error
When the toner motor M is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the toner motor M copyir.com Defective toner motor M copyir.com Defective engine PWB copyir.com
7004 Toner motor Y error
When the toner motor Y is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the toner motor Y copyir.com Defective toner motor Y copyir.com Defective engine PWB copyir.com
7401 Developing unit K noninstalling error
No density detection signal is output from toner sensor K in developing unit K copyir.com Defective connector cable or poor contact in the connector copyir.com Defective toner sensor K copyir.com Defective engine PWB copyir.com
7402 Developing unit C noninstalling error
No density detection signal is output from toner sensor C in developing unit C copyir.com Defective connector cable or poor contact in the connector copyir.com Defective toner sensor C copyir.com Defective engine PWB copyir.com
7403 Developing unit M noninstalling error
No density detection signal is output from toner sensor M in developing unit M copyir.com Defective connector cable or poor contact in the connector copyir.com Defective toner sensor M copyir.com Defective engine PWB copyir.com
7404 Developing unit Y noninstalling error
No density detection signal is output from toner sensor Y in developing unit Y copyir.com Defective connector cable or poor contact in the connector copyir.com Defective toner sensor Y copyir.com Defective engine PWB copyir.com
7411 Drum unit K non- installing error
The EEPROM of drum PWB K does not communicate normally copyir.com Installation of incompatible drum unit K copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drum PWB K copyir.com Defective engine PWB copyir.com
7412 Drum unit C non- installing error
The EEPROM of drum PWB C does not communicate normally copyir.com Installation of incompatible drum unit C copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drum PWB C copyir.com Defective engine PWB copyir.com
7413 Drum unit M non- installing error
The EEPROM of drum PWB M does not communicate normally copyir.com Installation of incompatible drum unit M copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drum PWB M copyir.com Defective engine PWB copyir.com
7414 Drum unit Y non- installing error
The EEPROM of drum PWB Y does not communicate normally copyir.com Installation of incompatible drum unit Y copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drum PWB Y copyir.com Defective engine PWB copyir.com
9500 copyir.com copyir.com copyir.com 9520 Contact the Service Administrative Division copyir.com
9530 Backup data error
The serial number of the machine written on the EEPROM of the engine PWB differs with that is written on both the flash memory of the engine PWB and the EEPROM of the drum PWB as a backup copyir.com Replacing both the engine PWB and the drum unit at the same time copyir.com
F000 Main PWB – operation panel PWB communication error Defective main PWB copyir.com Defective operation panel PWB copyir.com
F010 Main PWB checksum error Defective main PWB
F020 Main PWB RAM checksum errors Defective main memory (RAM) on the main PWB copyir.com Defective expanded memory (DIMM) copyir.com
F040 Main PWB – print engine communication error Defective main PWB copyir.com Defective engine PWB copyir.com
F041 Main PWB – scanner engine communication error Defective main PWB copyir.com Defective engine PWB copyir.com
F050 Print engine ROM checksum error Defective engine PWB copyir.com
F051 Scanner engine ROM checksum error Defective engine PWB copyir.com
F278 Power supply in drive system error Main power switch was turned off without using the power key, or a power failure has occurred copyir.com