لمینت MKP
1402-06-04
Menu
0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem copyir.com Defective FAX control PWB copyir.com
0070 FAX control PWB incompatible detection error
In the initial communication with the FAX control PWB, the normal communication command is not transmitted copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0100 Backup memory device error Defective flash memory copyir.com
Defective main PWB copyir.com
0120 MAC address data error
The data includes an invalid MAC address copyir.com Defective flash memory copyir.com
Defective engine PWB copyir.com
0130 Backup memory read/write error (main PWB) Defective flash memory copyir.com
Defective main PWB copyir.com
0140 Backup memory data error (main PWB) Defective flash memory copyir.com
Defective main PWB copyir.com
0150 Backup memory read/write error (engine PWB)
Detecting engine PWB EEPROM communication error copyir.com The engine PWB EEPROM was improperly installed copyir.com
Defective engine PWB copyir.com
Defective EEPROM copyir.com
0160 Backup memory data error (engine PWB) Defective flash memory copyir.com
Defective engine PWB copyir.com
0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters copyir.com Data in the EEPROM copyir.com
Defective PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data in the EEPROM copyir.com
0320 I/O CPU communication error
A communication error is detected 10 times in succession copyir.com Defective PWB copyir.com
0800 Image processing error
The JAM100 fee counter is continuously generated copyir.com Defective main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com The battery is disconnected from the main PWB copyir.com
Defective main PWB copyir.com
0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com Improper installation FAX control PWB copyir.com
Defective FAX control PWB or main PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com Defective FAX control PWB copyir.com
1010 Lift motor error
After cassette 1 is inserted, the lift sensor does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of the lift motor copyir.com
Defective lift motor copyir.com
Defective engine PWB copyir.com
1020 PF lift motor 1 error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of the PF lift motor 1 copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1030 PF lift motor 2 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of the PF lift motor 2 copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1800 Paper feeder communication error
A communication error is detected 10 times in succession copyir.com Improper installation of the paper feeder copyir.com
Defective connector cable or poor contact of the connector copyir.com
Defective engine PWB copyir.com
Defective PF main PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, the write data and the read data is not continuously in agreement 4 times copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
1950 Transfer belt unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Defective transfer PWB copyir.com
Device damage of EEPROM copyir.com
2101 Developer motor K steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor K stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2102 Developer motor YCM steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor YCM stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2111 Developer motor K startup error
Developer motor K is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2112 Developer motor YCM startup error
Developer motor YCM is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2201 Drum motor K steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the drum motor K stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2202 Drum motor YCM steady-state error
The rated speed signal detected the stability OFFcontinuously for 1 s after the drum motor YCM stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2211 Drum motor K startup error
Drum motor K is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2212 Drum motor YCM startup error
Drum motor YCM is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2300 Fuser motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the fuser motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2310 Fuser motor startup error
Fuser motor is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2550 Conveying motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the conveying motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2560 Conveying motor startup error
Conveying motor is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor
Defective PWB copyir.com
2600 PF drive motor error (paper feeder)
When the PF drive motor is driven, error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
2700 TC belt motor error
When the TC belt motor is driven, error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
3100 ISU home position error
ON/OFF of the HP sensor doesn’t change after a prescribed pulse passes from power supply ON copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective home position sensor copyir.com
Defective ISU motor copyir.com
Defective CCD PWB copyir.com
Defective engine PWB copyir.com
3200 Exposure lamp error
The input during the exposure lamp is turned on does not exceed the threshold for 5 seconds copyir.com Defective connector cable or poor contact of the connector copyir.com
Defective exposure lamp copyir.com
Defective CCD PWB copyir.com
Defective main PWB copyir.com
3500 Communication error
A wrong read-back value copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CCD PWB copyir.com
Defective main PWB copyir.com
3600 Scanner sequence error Defective main PWB or engine PWB copyir.com
4001 Polygon motor (K) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (K) stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor
Defective PWB copyir.com
4002 Polygon motor (C) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (C) stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor copyir.com
Defective PWB copyir.com
4003 Polygon motor (M) steady-state error The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (M) stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor copyir.com
Defective PWB copyir.com
4004 Polygon motor (Y) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (Y) stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor copyir.com
Defective PWB copyir.com
4011 Polygon motor (K) startup error
Polygon motor (K) is not stabilized within 10 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor copyir.com
Defective PWB copyir.com
4012 Polygon motor (C) startup error
Polygon motor (C) is not stabilized within 10 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor copyir.com
Defective PWB copyir.com
4013 Polygon motor (M) startup error
Polygon motor (M) is not stabilized within 10 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor copyir.com
Defective PWB copyir.com
4014 Polygon motor (Y) startup error
Polygon motor (Y) is not stabilized within 10 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor copyir.com
Defective PWB copyir.com
4101 BD initialization problem (K)
BD is not detected within one second after the polygon motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APCPWB copyir.com
Defective BDPWB copyir.com
Defective Main PWB copyir.com
4102 BD initialization problem (C)
BD is not detected within one second after the polygon motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APCPWB copyir.com
Defective BDPWB copyir.com
Defective Main PWB copyir.com
4103 BD initialization problem (M)
BD is not detected within one second after the polygon motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APCPWB copyir.com
Defective BDPWB copyir.com
Defective Main PWB copyir.com
4104 BD initialization problem (Y)
BD is not detected within one second after the polygon motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APCPWB copyir.com
Defective BDPWB copyir.com
Defective Main PWB copyir.com
4600 LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com Defective PWB copyir.com
4700 VIDEO ASIC device error
Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective main PWB or engine PWB copyir.com
4950 LSU CPU communication error
A communication error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
6000 Broken fuser heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after20 s during warming up copyir.com The detected temperature of fuser thermistor2 does not reach the specified temperature (ready indication temperature) for 20 s in warming up after reached to 100° C/ 212 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective IH PWB copyir.com
Fuser thermostat triggered copyir.com
Broken fuser heater wire copyir.com
Defective engine PWB copyir.com
6020 Abnormally high fuser thermistor 2 (center) temperature
The fuser thermistor 2 detects a temperature higher than 240°C/464°F continuously for 1 s copyir.com Deformed connector pin copyir.com
Shorted fuser thermistor copyir.com
Defective engine PWB copyir.com
6030 Fuser thermistor 2 (center) break error
A/D value of the fuser thermistor 2 exceeds 984 bit continuously for 1 s during warming up copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective fuser thermistor
Defective engine PWB copyir.com
6040 NC sensor error Deformed connector pin copyir.com
Shorted fuser thermistor copyir.com
Defective engine PWB copyir.com
6050 Abnormally low fuser thermistor 2 (center) temperature
The fuser temperature lower than 100 °C/212 °F is detected continuously for 1 s during printing copyir.com The fuser temperature lower than 70 °C/158 °F is detected continuously for 1 s during pre-heating copyir.com Deformed connector pin copyir.com
Defective fuser thermistor copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6120 Abnormally high fuser thermistor 3 (press roller) temperature
The fuser temperature exceeds 200 °C/392 °F for 1 s copyir.com Deformed connector pin copyir.com
Defective IH PWB copyir.com
Defective fuser thermistor copyir.com
Defective engine PWB copyir.com
6130 Fuser thermistor 3 (press roller) break error Fuser thermistor 3 detects a temperature of -14 °C/6 copyir.com8 °F copyir.com Fuser thermistor 3 does not reach 30° C/86 °F even after20 s during warming up copyir.com Defective connector cable or poor contact in the connector
Deformed connector pin copyir.com
Defective IH PWB copyir.com
Defective fuser thermistor copyir.com
Defective engine PWB copyir.com
6150 Abnormally low fuser thermistor 3 (press roller) temperature
The fuser temperature lower than 30 °C/86 °F is detected continuously for 1 s copyir.com Deformed connector pin copyir.com
Defective fuser thermistor
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6200 Broken fuser edge heater wire
Fuser thermistor 1 does not reach 50° C/122 °F even after20 s during warming up copyir.com The detected temperature of fuser thermistor1 does not reach the specified temperature (ready indication temperature) for 20 s in warming up after reaching 50° C/122 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Fuser thermostat triggered copyir.com
Broken fuser heater wire copyir.com
Defective engine PWB copyir.com
6220 Abnormally high fuser thermistor 1 (edge) temperature
The fuser temperature exceeds 240 °C/464 °F for 1 s copyir.com Deformed connector pin copyir.com
Defective cooling fan motor copyir.com
Defective fuser thermistor copyir.com
Defective engine PWB copyir.com
6230 Fuser thermistor 1 (edge) break error
During warming up a hearter, fuser thermistor 2 detects a temperature of 100 °C/212 °F or higher and, fuser thermistor 1 detects a temperature of 37 °C/99 °F or lower copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective fuser thermistor copyir.com
Defective engine PWB copyir.com
6250 Abnormally low fuser thermistor 1 (edge) temperature
The fuser temperature lower than 100 °C/212 °F is detected continuously for 1 s during printing copyir.com The fuser temperature lower than 50 °C/122 °F is detected continuously for 1 s during pre-heating copyir.com Deformed connector pin copyir.com
Defective IH PWB copyir.com
Defective fuser thermistor copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6410 Fuser unit type mismatch problem
Absence of the fuser unit is detected copyir.com Fuser unit connector inserted incorrectly copyir.com
Different type of the fuser unit is installed copyir.com
6600 Belt rotation error
The belt was detected to stop for 1 s continuously during motor remote is on copyir.com Defective fuser motor copyir.com
Defective IH belt copyir.com
Defective IH PWB copyir.com
Defective engine PWB copyir.com
6710 CPU thermal runaway (IHPWB) Defective IH PWB copyir.com
6720 Belt rotation error (IHPWB) Defective IH PWB copyir.com
Defective fuser motor copyir.com
Defective fuser unit copyir.com
6730 Abnormally high IGBT1 temperature (IHPWB) Defective IH PWB copyir.com
Defective cooling fan motor copyir.com
6740 Abnormally high IGBT2 temperature (IHPWB) Defective IH PWB copyir.com
Defective cooling fan motor copyir.com
6750 Abnormally output overcurrent (IHPWB) Defective IH PWB copyir.com
Defective fuser unit copyir.com
6760 Abnormally AC input over-current (IHPWB) Defective IH PWB copyir.com
6770 Abnormally low electric power (IHPWB) Defective connector cable or poor contact in the connector copyir.com
Defective IH PWB copyir.com
6930 IH coil fan motor error
The alarm signal was detected for 5 seconds continuously during operation copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective cooling fan motor copyir.com
Defective IH PWB
6950 IH CPU communication error A communication error is detected 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective IH PWB copyir.com
Defective engine PWB copyir.com
6990 Fuser unit type mismatch problem
Absence of the fuser unit is detected copyir.com Defective IH PWB copyir.com
7001 Toner motor K error
When the toner motor K is driven, error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
7002 Toner motor C error
When the toner motor C is driven, error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
7003 Toner motor M error
When the toner motor M is driven, error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
7004 Toner motor Y error
When the toner motor Y is driven, error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system copyir.com
Defective motor copyir.com
Defective PWB copyir.com
7101 Toner sensor K error Defective Developer unit copyir.com
Defective PWB copyir.com
7102 Toner sensor C error Defective Developer unit copyir.com
Defective PWB copyir.com
7103 Toner sensor M error Defective Developer unit copyir.com
Defective PWB copyir.com
7104 Toner sensor Y error Defective Developer unit copyir.com
Defective PWB copyir.com
7401 Developing unit K type mismatch problem
Absence of the developing unit K is detected copyir.com Developing unit connector inserted incorrectly copyir.com
Different type of the developing unit is installed copyir.com
Defective PWB copyir.com
7402 Developing unit C type mismatch problem
Absence of the developing unit C is detected copyir.com Developing unit connector inserted incorrectly copyir.com
Different type of the developing unit is installed copyir.com
Defective PWB copyir.com
7403 Developing unit M type mismatch problem
Absence of the developing unit M is detected copyir.com Developing unit connector inserted incorrectly copyir.com
Different type of the developing unit is installed copyir.com
Defective PWB copyir.com
0121 EEPROM read error (drum PWB K)
• When data is transmitted to the EEPROM on drum PWB K, the ACK signal is not returned within 1 s copyir.com Poor contact in the connector terminals copyir.com
0122 EEPROM read error (drum PWB C)
• When data is transmitted to the EEPROM on drum PWB C, the ACK signal is not returned within 1 s copyir.com Poor contact in the connector terminals copyir.com
0123 EEPROM read error (drum PWB M)
• When data is transmitted to the EEPROM on drum PWB M, the ACK signal is not returned within 1 s copyir.com Poor contact in the connector terminals copyir.com Defective drum PWB M copyir.com
0124 EEPROM read error (drum PWB Y)
• When data is transmitted to the EEPROM on drum PWB Y, the ACK signal is not returned within 1 s copyir.com Poor contact in the connector terminals copyir.com
0150 Backup memory device problem (Engine controller PWB)
• An error occurs in backup data read or write for the engine controller PWB copyir.com • An error occurs in control area deletion copyir.com Defective engine controller PWB copyir.com
0160 Backup memory data problem (Engine controller PWB)
• Data for backup data check is changed at the check after startup copyir.com Defective engine controller PWB copyir.com
0170 Total counts problem
• A checksum error is detected in the main and sub backup memories for the total counters copyir.com Data damage of EEPROM copyir.com
0240 Main controller PWB communication problem
• The main controller PWB does not respond 120 seconds after the power is turned on copyir.com Poor contact in the connector terminals copyir.com DIMM installed incorrectly copyir.com Defective engine interface PWB or main controller PWB copyir.com
0310 LPH drive PWB communication error
• When an error in communication with the CPU for LPH control on the LPH drive PWB is detected, transmission/ reception is not normally completed even after 10 times of retry copyir.com Poor contact in the connector terminals copyir.com Defective LPH drive PWB copyir.com Defective engine controller PWB copyir.com
0420 Paper feeder communication error 1 (upper of optional paper feeder PF- 640)
• Reception is not normally completed even after 40 times of retry at startup or 5 times of retry in normal operation copyir.com Poor contact in the connector terminals copyir.com Defective engine controller PWB copyir.com Defective upper of optional paper feeder PF-640 copyir.com
0440 Document finisher communication problem (optional document finisher)
• Reception is not normally completed even after 40 times of retry at startup or 5 times of retry in normal operation copyir.com Poor contact in the connector terminals copyir.com Defective engine controller PWB copyir.com Defective optional document finisher
0500 Paper feeder communication error 1 (lower of optional paper feeder PF- 640)
• Reception is not normally completed even after 40 times of retry at startup or 5 times of retry in normal operation copyir.com Poor contact in the connector terminals copyir.com Defective engine controller PWB copyir.com Defective lower of optional paper feeder PF-640 copyir.com
0700 Paper feeder EEPROM error 1 (upper of optional paper feeder PF-640)
• When power is turned on, an error is detected in memory check for the upper of the optional 500 sheets paper feeder and a backup memory error is received in serial communication data Poor contact in the connector terminals copyir.com Defective engine controller PWB copyir.com Defective upper of optional paper feeder PF-640 copyir.com
0710 Paper feeder EEPROM error 2 (lower of optional paper feeder PF-640)
• When power is turned on, an error is detected in memory check for the lower of the paper feeder PF-640 and a backup memory error is received in serial communication data copyir.com Poor contact in the connector terminals copyir.com Defective engine controller PWB copyir.com Defective lower of optional paper feeder PF-640 copyir.com
0750 Document finisher EEPROM error
• A backup memory error is received in serial communication data from the finisher copyir.com Poor contact in the connector terminals copyir.com Defective engine controller PWB copyir.com Defective optional document finisher copyir.com
0926 LPH current correction EEPROM error
• A correction data error for the second color (cyan) is detected copyir.com copyir.com Defective EEPROM of LPH drive PWB copyir.com
0951 LPH current correction EEPROM error
• A correction data error for the fourth color (black) is detected copyir.com Defective EEPROM of LPH drive PWB copyir.com
0953 LPH current correction EEPROM error
• A correction data error for the first color (magenta) is detected copyir.com Defective EEPROM of LPH drive PWB copyir.com
0954 LPH current correction EEPROM error
• A correction data error for the third color (yellow) is detected copyir.com Defective EEPROM of LPH drive PWB copyir.com
1010 Cassette lift motor error
• The bottom plate limit detection sensor is not turned on within 9,000 ms after the cassette is inserted and the sensor is not turned on within 500 ms at the second time and after copyir.com Defective bottom plate elevation mechanism copyir.com Defective cassette lift motor copyir.com Defective engine controller PWB copyir.com
1100 Cassette lift motor error (upper cassette of optional paper feeder PF-645)
• The paper feeder upper limit detection sensor is not turned on within 10,000 ms after the upper cassette is inserted and the sensor is not turned on within 500 ms at the second time and after copyir.com Defective bottom plate elevation mechanism copyir.com Defective upper cassette lift motor copyir.com Defective engine controller PWB copyir.com Defective bottom plate elevation mechanism copyir.com Defective middle cassette lift motor copyir.com Defective engine controller PWB copyir.com
1120 Cassette lift motor error (lower cassette of optional paper feeder PF-645)
• The paper feeder lower limit detection sensor is not turned on within 10,000 ms after the lower cassette is inserted and the sensor is not turned on within 500 ms at the second time and after copyir.com Defective bottom plate elevation mechanism copyir.com Defective lower cassette lift motor copyir.com Defective engine controller PWB copyir.com
1130 Cassette lift motor error (cassette of paper feeder PF-647)
• The paper feeder limit detection sensor is not turned on within 10,000 ms after the cassette is inserted and the sensor is not turned on within 500 ms at the second time and after copyir.com Defective bottom plate elevation mechanism copyir.com Defective cassette lift motor copyir.com Defective engine controller PWB copyir.com
1140 Deck lift motor error (right deck of paper feeder PF-647)
• The right deck limit detection sensor is not turned on within 60,000 ms after the right deck is inserted and the sensor is not turned on within 1,000 ms at the second time and after copyir.com Defective bottom plate elevation mechanism copyir.com Defective right deck lift motor copyir.com Defective engine controller PWB copyir.com
1150 Deck lift motor error (left deck of paper feeder PF-647)
• The left deck limit detection sensor is not turned on within 60,000 ms after the left deck is inserted and the sensor is not turned on within 1,000 ms at the second time and after copyir.com Defective bottom plate elevation mechanism copyir.com Defective left deck lift motor copyir.com Defective engine controller PWB copyir.com
1160 Cassette lift motor error (upper of paper feeder PF-640)
• The paper feeder limit detection sensor is not turned on within 10,000 ms after the cassette is inserted and the sensor is not turned on within 500 ms at the second time and after copyir.com Defective bottom plate elevation mechanism copyir.com Defective cassette lift motor copyir.com Defective engine controller PWB copyir.com
1170 Cassette lift motor error (lower of paper feeder PF-640)
• The paper feeder limit detection sensor is not turned on within 10,000 ms after the cassette is inserted and the sensor is not turned on within 500 ms at the second time and after copyir.com Defective bottom plate elevation mechanism copyir.com Defective cassette lift motor copyir.com Defective engine controller PWB copyir.com
1200 Duplex side registration motor error (optional duplex unit*)
• The duplex side registration home position sensor does not detect the home position of the side registration guide copyir.com *Duplex unit is standard equipment for 120 V (U copyir.comS copyir.comA copyir.com) specifications copyir.com Defective duplex side registration home position sensor copyir.com Defective duplex side registration motor copyir.com Defective engine controller PWB copyir.com
2101 Developing K/fuser motor error
• After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective developing K/fuser motor copyir.com Defective engine controller PWB copyir.com
2102 Developing MCY motor error
• After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective developing MCY motor copyir.com Defective engine controller PWB copyir.com
2201 Drum motor K error
• After the motor drive ON signal is output and 3 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drum motor K copyir.com Defective engine controller PWB copyir.com
2202 Drum motor C error
• After the motor drive ON signal is output and 3 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drum motor C copyir.com Defective engine controller PWB copyir.com
2203 Drum motor M error
• After the motor drive ON signal is output and 3 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drum motor M copyir.com Defective engine controller PWB copyir.com
2204 Drum motor Y error
• After the motor drive ON signal is output and 3 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drum motor Y copyir.com Defective engine controller PWB copyir.com
2500 Paper feed motor error
• After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective paper feed motor copyir.com Defective engine controller PWB copyir.com
2600 Paper feed motor error (optional paper feeder PF-645/647)
• After the motor drive ON signal is output and 2 s elapse, paper feed motor error communication data is transmitted continuously for 1 s copyir.com Poor contact in the connector terminals copyir.com Defective paper feed motor copyir.com Defective engine controller PWB copyir.com
2700 Transfer lift motor error
• Even if 5,000 ms elapse after the transfer lift motor drive signal is turned on, the transfer lift home position sensor is not turned on copyir.com • Even if 5,000 ms elapse after the transfer lift motor drive ON signal is output, the transfer lift home position sensor is not turned off copyir.com Poor contact in the connector terminals copyir.com Defective transfer lift home position sensor copyir.com Defective transfer lift motor copyir.com Misfeed in the conveying section or fuser section copyir.com
2710 Waste toner box motor error
• After the motor drive remote signal is turned on, the overcurrent detection signal is detected continuously for more than 200 ms copyir.com Overload on the waste toner box motor copyir.com Defective waster toner box motor copyir.com
5100 Main high-voltage error
• While the main high-voltage output remote signal is on, an alarm signal is detected continuously for 400 ms copyir.com Leak of main highvoltage copyir.com
5301 Eraser lamp K break error
• After the eraser lamp K ON signal is turned on, the eraser lamp K break signal is detected continuously for 200 ms copyir.com Poor contact in the connector terminals copyir.com Defective eraser lamp K copyir.com
5302 Eraser lamp C break error
• After the eraser lamp C ON signal is turned on, the eraser lamp C break signal is detected continuously for 200 ms copyir.com Poor contact in the connector terminals copyir.com Defective eraser lamp C copyir.com
5303 Eraser lamp M break error
• After the eraser lamp C ON signal is turned on, the eraser lamp M break signal is detected continuously for 200 ms copyir.com Poor contact in the connector terminals copyir.com Defective eraser lamp M copyir.com
5304 Eraser lamp Y break error
• After the eraser lamp Y ON signal is turned on, the eraser lamp Y break signal is detected continuously for 200 ms copyir.com Poor contact in the connector terminals copyir.com Defective eraser lamp Y copyir.com
6000 Upper fuser heater lamp break
• The time for increasing the temperature at the upper fuser heater lamp to 60°C during warm-up exceeds 100 s from the start of warm-up copyir.com Then, the time for increasing the temperature from 60 °C/140 °F to 120 °C/248 °F exceeds 100 s copyir.com Installation defectiveness on upper fuser thermistor copyir.com Defective upper fuser thermostat copyir.com Defective engine controller PWB copyir.com Defective power supply PWB copyir.com Defective fuser PWB copyir.com Connected malfunction of electric wire on upper fuser thermistor or connected malfunction of connector terminal copyir.com Defective upper fuser heater lamp copyir.com
6020 Upper fuser thermistor high-temperature detection error
• The temperature at the upper fuser roller 205 °C/401 °F or more is detected continuously for 5 s copyir.com Defective engine controller PWB copyir.com Defective fuser PWB copyir.com Defective power supply PWB copyir.com Installation defectiveness on upper fuser thermistor copyir.com Defective upper fuser thermistor copyir.com
6030 Upper fuser thermistor break error
• After the fuser heater lamp is turned on, the temperature at the upper fuser roller lower than 40 °C/104 °F continues for 30 s copyir.com Defective engine controller PWB copyir.com Defective harness between fuser PWB and upper fuser thermistor, or poor contact of the connector terminals copyir.com Defective harness between fuser PWB and fuser unit connectors copyir.com Defective harness between power supply PWB and fuser unit connectors copyir.com Defective fuser PWB copyir.com Defective power supply PWB copyir.com Installation defectiveness on upper fuser thermistor copyir.com
6050 Upper fuser thermistor abnormal temperature detection
• During copying, the temperature at the upper fuser roller lower than 120 °C/ 248 °F is detected continuously for 5 s copyir.com Installation defectiveness on upper fuser thermistor copyir.com Operation on upper fuser thermostat copyir.com Defective engine controller PWB copyir.com Defective power supply PWB copyir.com Defective fuser PWB copyir.com Defective harness between fuser PWB and upper fuser thermistor, or poor contact of the connector terminals copyir.com Defective upper fuser heater lamp copyir.com Defective harness between fuser unit connectors and upper fuser heater lamp copyir.com Defective harness between fuser unit connectors and power supply PWB copyir.com
6100 Lower fuser heater lamp break
• The time for increasing the temperature at the upper fuser heater lamp to 60 °C/140 °F during warm-up exceeds 100 s from the start of warm-up copyir.com Then, the time for increasing the temperature from 60 °C/140 °F to 120 °C/218 °F exceeds 100 s copyir.com Installation defectiveness on lower fuser thermistor copyir.com Operation on lower fuser thermostat copyir.com Defective engine controller PWB copyir.com Defective power supply PWB copyir.com Defective fuser PWB copyir.com Defective harness of lower fuser thermistor, or poor contact of the connector terminals copyir.com Defective lower fuser heater lamp copyir.com
6120 Lower fuser thermistor detection error
• The temperature at the lower fuser roller 205 °C/401 °F or more is detected continuously for 5 s copyir.com Defective engine controller PWB copyir.com Defective fuser PWB copyir.com Defective power supply PWB copyir.com Installation defectiveness on lower fuser thermistor copyir.com Defective lower fuser thermistor copyir.com
6130 Lower fuser thermistor break error
• After the fuser heater lamp is turned on, the temperature at the upper fuser roller lower than 40 °C/104 °F continues for 30 s copyir.com Defective engine controller PWB copyir.com Defective harness between fuser PWB and lower fuser thermistor, or poor contact of the connector terminals copyir.com Defective harness between fuser PWB and fuser unit connectors copyir.com Defective harness between power supply PWB and fuser unit connectors copyir.com Defective fuser PWB copyir.com Defective power supply PWB copyir.com Installation defectiveness on lower fuser thermistor copyir.com
6150 Lower fuser thermistor abnormal temperature detection
• During copying, the temperature at the lower fuser roller lower than 100 °C/ 212 °F is detected continuously for 5 s copyir.com Installation defectiveness on lower fuser thermistor copyir.com Operation on lower fuser thermostat copyir.com Defective engine controller PWB copyir.com Defective power supply PWB copyir.com Defective fuser PWB copyir.com Defective harness between fuser PWB and upper fuser thermistor, or poor contact of the connector terminals copyir.com Defective lower fuser heater lamp copyir.com Defective harness between fuser unit connectors and lower fuser heater lamp copyir.com Defective harness between fuser unit connectors and power supply PWB copyir.com
6400 Zero-cross signal error
• After power is turned on, the zerocross signal is not input within 3 s copyir.com • While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 5 s copyir.com Defective engine controller PWB copyir.com Defective power supply PWB copyir.com
6410 Fuser unit insertion error
• Improper adaptation of the machine and the fuser unit is detected copyir.com Fuser unit connector inserted incorrectly copyir.com Defective fuser unit connector copyir.com
6420 Fuser fuse cut error
• After a new fuser unit is installed and the fuse cut signal is turned on and then the fuse cut signal is turned off after 3,000 ms, the fuse cannot be cut copyir.com Fuser unit is not conformed copyir.com Defective engine controller PWB copyir.com
7001 Toner motor K error • After the toner motor K drive signal is turned on, the toner motor K overcurrent detection signal is detected continuously for 180 x 50 ms copyir.com Defective toner motor K copyir.com Defective engine controller PWB copyir.com
7002 Toner motor C error
• After the toner motor C drive signal is turned on, the toner motor C overcurrent detection signal is detected continuously for 180 x 50 ms copyir.com Defective toner motor C copyir.com Defective engine controller PWB copyir.com
7003 Toner motor M error
• After the toner motor M drive signal is turned on, the toner motor M overcurrent detection signal is detected continuously for 180 x 50 ms copyir.com Defective toner motor M copyir.com Defective engine controller PWB copyir.com
7004 Toner motor Y error
• After the toner motor Y drive signal is turned on, the toner motor Y overcurrent detection signal is detected continuously for 180 x 50 ms copyir.com Defective toner motor Y copyir.com Defective engine controller PWB copyir.com
7101 Toner sensor K error
• The value of input from toner sensor K is 4 copyir.com5 V or more or 0 copyir.com5 V or less copyir.com Defective toner sensor K copyir.com Defective engine controller PWB copyir.com
7102 Toner sensor C error
• The value of input from toner sensor C is 4 copyir.com5 V or more or 0 copyir.com5 V or less copyir.com Defective toner sensor C copyir.com Defective engine controller PWB copyir.com
7103 Toner sensor M error
• The value of input from toner sensor M is 4 copyir.com5 V or more or 0 copyir.com5 V or less copyir.com Defective toner sensor M copyir.com Defective engine controller PWB copyir.com
7104 Toner sensor Y error
• The value of input from toner sensor Y is 4 copyir.com5 V or more or 0 copyir.com5 V or less copyir.com Defective toner sensor Y copyir.com Defective engine controller PWB copyir.com
7200 Broken internal thermistor wire
• The value of input from the internal thermistor 4 copyir.com5 V or more is detected copyir.com Poor contact in the connector terminals copyir.com Defective engine controller PWB copyir.com
7210 Short-circuited internal thermistor
• The value of input from the internal thermistor 0 copyir.com3 V or less is detected copyir.com Poor contact in the connector terminals copyir.com Defective engine controller PWB copyir.com
7301 Toner hopper error (black process unit)
• When black toner is replenished (simple replenishment), if the replenishment release level is not reached even if black toner is replenished for 3 s (1 s) with the black toner low level not detected, the state is regarded as a black toner container non-installing error copyir.com This error occurs four times copyir.com Black toner container is not installed copyir.com Defective engine controller PWB copyir.com
7302 Toner hopper error (cyan process unit)
• When cyan toner is replenished (simple replenishment), if the replenishment release level is not reached even if cyan toner is replenished for 3 s (1 s) with the black toner low level not detected, the state is regarded as a cyan toner container non-installing error copyir.com This error occurs four times copyir.com Cyan toner container is not installed copyir.com Defective engine controller PWB copyir.com
7303 Toner hopper error (magenta process unit)
• When magenta toner is replenished (simple replenishment), if the replenishment release level is not reached even if magenta toner is replenished for 3 s (1 s) with the magenta toner low level not detected, the state is regarded as a magenta toner container non-installing error copyir.com This error occurs four times copyir.com Magenta toner container is not installed copyir.com Defective engine controller PWB copyir.com
7304 Toner hopper error (yellow process unit)
• When yellow toner is replenished (simple replenishment), if the replenishment release level is not reached even if yellow toner is replenished for 3 s (1 s) with the yellow toner low level not detected, the state is regarded as a yellow toner container non-installing error copyir.com This error occurs four times copyir.com Yellow toner container is not installed copyir.com Defective engine controller PWB copyir.com
7600 Toner ID sensor problem
• The sampling input of toner ID sensor 1 and toner ID sensor 2 without patch exceeds the threshold respectively copyir.com Defective toner ID sensor 1 or 2 copyir.com Defective engine controller PWB copyir.com
7610 Image density measurement timing problem
• The measured value of density patch is abnormal copyir.com Faulty density due to a mechanical cause copyir.com
7620 Color registration timing error
• The number of PG lines for registration correction 32 is not detected properly Defective engine controller PWB copyir.com
7800 Broken external thermistor wire
• The thermistor output value is 4 copyir.com5 V or more copyir.com Poor contact in the connector terminals copyir.com
7810 Short-circuited external thermistor • The thermistor input value is 0 copyir.com5 V or less copyir.com Poor contact in the connector terminals copyir.com Defective engine controller PWB copyir.com
8010 Optional document finisher paper conveying motor problem
• The LOCK signal of the paper conveying motor is detected for more than 500 ms while the paper conveying motor is operating copyir.com However, the first 1 s after the paper conveying motor is turned on is excluded from detection copyir.com Loose connection of the paper conveying motor connector copyir.com Defective paper conveying motor copyir.com Defective finisher main PWB copyir.com
8020 Optional document finisher punch motor problem
• The LOCK signal of the punch motor is detected for more than 500 ms while the punch motor is operating copyir.com However, the first 1 s after the punch motor is turned on is excluded from detection copyir.com Loose connection of the punch motor connector copyir.com Defective punch motor copyir.com Defective finisher main PWB copyir.com
8030 Optional document finisher upper paper conveying belt problem
• During initialization, the intermediate tray upper sliding plate is not detected in the home position within 3 s after the belt returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem reoccurs after initialization when the front cover is opened and closed, the problem is in the upper paper conveying belt copyir.com • When the intermediate tray upper sliding plate is operated from the home position, the upper paper conveying belt home position sensor does not turn off within 1 s copyir.com Phase shift of the upper paper conveying belt copyir.com Malfunction of the upper paper conveying belt motor copyir.com Malfunction of the upper paper conveying belt home position sensor copyir.com Loose connection of the upper paper conveying belt home position sensor connector copyir.com Incorrect insertion of the intermediate tray copyir.com Defective finisher main PWB copyir.com
8040 Optional document finisher lower paper conveying belt problem
• During initialization, the intermediate tray lower sliding plate is not detected in the home position within 3 s after the belt returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem reoccurs after initialization when the front cover is opened and closed, the problem is in the lower paper conveying belt copyir.com • When the intermediate tray lower sliding plate is operated from the home position, the lower paper conveying belt home position sensor does not turn off within 1 s copyir.com Phase shift of the lower paper conveying belt copyir.com Malfunction of the lower paper conveying belt motor copyir.com Malfunction of the lower paper conveying belt home position sensor copyir.com Loose connection of the lower paper conveying belt home position sensor connector copyir.com Incorrect insertion of the intermediate tray copyir.com Defective finisher main PWB copyir.com
8140 Optional document finisher main tray problem
• When the main tray is not detected by the main tray upper limit detection sensor or the main tray load detection sensor within 20 s from the moment it starts ascending copyir.com • During main tray descent, the main tray upper limit detection sensor or the main tray load detection sensor does not turn off within 500 ms after it turns on copyir.com • During main tray ascent, the main tray upper limit detection sensor or the main tray load detection sensor stays on for more than 2 s copyir.com Loose connection of the main tray elevation motor connector copyir.com Malfunction of the main tray elevation motor copyir.com Malfunction of the main tray upper limit detection sensor copyir.com Loose connection of the main tray upper limit detection sensor connector copyir.com Malfunction of the main tray load detection sensor copyir.com Loose connection of the main tray load detection sensor connector copyir.com Defective finisher main PWB copyir.com
8150 Optional document finisher multi job tray problem
• When the multi job tray is not detected by the multi job tray upper limit detection sensor within 15 s from the moment it starts ascending copyir.com • During multi job tray descent, the multi job tray upper limit detection sensor does not turn off within 500 ms after it turns on copyir.com Loose connection of the multi job tray elevation motor connector copyir.com Malfunction of the multi job tray elevation motor copyir.com Malfunction of the multi job tray upper limit detection sensor copyir.com Loose connection of the multi job tray upper limit detection sensor connector copyir.com Defective finisher main PWB copyir.com
8170 Optional document finisher front upper side-registration guide problem
• During initialization, the front upper side-registration guide is not detected in the home position within 1 copyir.com5 s after the guide returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front upper side-registration guide copyir.com • When the front upper side-registration guide is operated from the home position, the front upper side-registration home position sensor does not turn off within 500 ms copyir.com Loose connection of the front upper side-registration guide motor connector copyir.com Malfunction of the front upper sideregistration guide motor copyir.com Malfunction of the front upper sideregistration guide home position sensor copyir.com Loose connection of the front upper side-registration guide home position sensor connector copyir.com Defective finisher main PWB copyir.com
8180 Optional document finisher rear upper side-registration guide problem
• During initialization, the rear upper side-registration guide is not detected in the home position within 1 copyir.com5 s after the guide returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear upper side-registration guide copyir.com • When the rear upper side-registration guide is operated from the home position, the rear upper side-registration home position sensor does not turn off within 500 ms copyir.com Loose connection of the rear upper side-registration guide motor connector copyir.com Malfunction of the rear upper sideregistration guide motor copyir.com Malfunction of the rear upper sideregistration guide home position sensor copyir.com Loose connection of the rear upper side-registration guide home position sensor connector copyir.com Defective finisher main PWB copyir.com
8190 Optional document finisher lower side-registration guide problem
• During initialization, the front/rear lower side-registration guides are not detected in the home position within 1 copyir.com5 s after the guide returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the lower side-registration guide copyir.com • When the lower side-registration guide is operated from the home position, the lower side-registration home position sensor does not turn off within 500 ms copyir.com Loose connection of the lower sideregistration guide motor connector copyir.com Malfunction of the lower side-registration guide motor copyir.com Malfunction of the lower side-registration guide home position sensor copyir.com Loose connection of the lower sideregistration guide home position sensor connector copyir.com Defective finisher main PWB copyir.com
8210 Optional document finisher front stapler problem
• During initialization, the front stapler is not detected in the home position within 500 ms after the front stapler returns to the home position copyir.com JAM90 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front stapler copyir.com • When the front stapler is operated from the home position, the front stapler home position sensor does not turn off within 500 ms copyir.com Loose connection of the front stapler motor connector copyir.com Malfunction of the front stapler motor copyir.com Malfunction of the front stapler home position sensor copyir.com Loose connection of the front stapler home position sensor connector copyir.com Defective finisher main PWB copyir.com
8220 Optional document finisher front clincher problem
• During initialization, the front clincher is not detected in the home position within 500 ms after the front clincher returns to the home position copyir.com JAM90 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front clincher copyir.com • When the front clincher is operated from the home position, the front clincher home position sensor does not turn off within 500 ms copyir.com Loose connection of the front clincher motor connector copyir.com Malfunction of the front clincher motor copyir.com Malfunction of the front clincher home position sensor copyir.com Loose connection of the front clincher home position sensor connector copyir.com Defective finisher main PWB copyir.com
8230 Document finisher* rear stapler problem
• During initialization, the rear stapler is not detected in the home position within 500 ms after the rear stapler returns to the home position copyir.com JAM90 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear stapler copyir.com • When the rear stapler is operated from the home position, the rear stapler home position sensor does not turn off within 500 ms copyir.com Loose connection of the rear stapler motor connector copyir.com Malfunction of the rear stapler motor copyir.com Malfunction of the rear stapler home position sensor copyir.com Loose connection of the rear stapler home position sensor connector copyir.com Defective finisher main PWB copyir.com
8240 Optional document finisher rear clincher problem
• During initialization, the rear clincher is not detected in the home position within 500 ms after the rear clincher returns to the home position copyir.com JAM90 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear clincher copyir.com • When the rear clincher is operated from the home position, the rear clincher home position sensor does not turn off within 500 ms copyir.com Loose connection of the rear clincher motor connector copyir.com Malfunction of the rear clincher motor copyir.com Malfunction of the rear clincher home position sensor copyir.com Loose connection of the rear clincher home position sensor connector copyir.com Defective finisher main PWB copyir.com
8300 Optional document finisher centerfold unit communication problem
• Communication with the centerfold unit is not possible although the connection is detected copyir.com Loose connection of the centerfold unit set switch connecto r copyir.com Defective centerfold unit set switch copyir.com Defective centerfold unit main PWB copyir.com Defective finisher main PWB copyir.com
8310 Optional document finisher centerfold unit side-registration guide problem
• During initialization, the front/rear sideregistration guides are not detected in the home position within 600 ms after the guide returns to the home position copyir.com • When the side-registration guide is operated from the home position, the side-registration guide home position sensor does not turn off within 100 ms copyir.com Loose connection of the side-registration guide motor connector copyir.com Malfunction of the side-registration guide motor copyir.com Malfunction of the side-registration guide home position sensor copyir.com Loose connection of the side-registration guide home position sensor connector copyir.com Defective centerfold unit main PWB copyir.com
8320 Optional document finisher centerfold unit centering plate problem
• During initialization, the centering plate is not detected in the home position when the centering plate returns to the home position copyir.com Loose connection of the centering plate motor connector copyir.com Malfunction of the centering plate motor copyir.com Malfunction of the centering plate home position sensor copyir.com Loose connection of the centering plate home position sensor connector copyir.com Defective centerfold unit main PWB copyir.com
8330 Optional document finisher centerfold blade problem
• During initialization, the centerfold blade is not detected in the home position within a specified period of time copyir.com Loose connection of the centerfold blade motor connector copyir.com Malfunction of the centerfold blade motor copyir.com Malfunction of the centerfold blade home position sensor copyir.com Loose connection of the centerfold blade home position sensor connector copyir.com Defective centerfold unit main PWB copyir.com
F000 Main controller PWB error
• The communication breakdown occurs between the main controller PWB and the operation panel PWB during the predetermined period in seconds Defective main controller PWB copyir.com Defective operator panel PWB copyir.com Defective engine interface PWB copyir.com Defective harness between operator panel PWB and engine interface PWB copyir.com
F010 Code ROM checksum error
• Checksum for the system code ROM PWB that holds the system program is wrong copyir.com Defective code ROM PWB copyir.com Defective main controller PWB copyir.com
F020 Memory check error
• Access to the expanding memory (DIMM) or RAM on the main controller PWB failed copyir.com Defective main controller PWB copyir.com Defective expansion memory (DIMM) copyir.com
F030 Main controller PWB system error
• The error pertaining to the system occurred except the F0 (F010) condition copyir.com Defective main controller PWB copyir.com
F040 Main – Engine controller PWBs communication error
• The communication breakdown occurred between the main controller PWB and the engine controller PWB during the predetermined period in seconds copyir.com Defective engine controller PWB copyir.com Defective main controller PWB copyir.com
F050 Engine checksum error
• Checksum result failed with the CPU and engine controller PWB copyir.com Defective engine controller PWB copyir.com
F060 Engine RAM error
• Checksum failed with RAM of the engine controller PWB copyir.com Defective engine controller PWB copyir.com
F070 Flash ROM checksum error
• Checksum failed with the flash ROM on the engine controller PWB copyir.com Defective engine controller PWB copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.