لمینت MKP
1402-06-04
Menu
0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem copyir.com Defective FAX control PWB copyir.com
0070 FAX control PWB incompatible detection error
In the initial communication with the FAX control PWB, the normal communication command is not transmitted copyir.com Defective FAX software copyir.com Defective FAX control PWB copyir.com
0100 Backup memory device error Defective flash memory copyir.com Defective main PWB copyir.com
0120 MAC address data error
The data includes an invalid MAC address copyir.com Defective flash memory copyir.com Defective engine PWB copyir.com
0130 Backup memory read/write error (main PWB) Defective flash memory copyir.com Defective main PWB copyir.com
0140 Backup memory data error (main PWB) Defective flash memory copyir.com Defective main PWB copyir.com
0150 Backup memory read/write error (engine PWB)
Detecting engine PWB EEPROM communication error copyir.com The engine PWB EEPROM was improperly installed copyir.com Defective engine PWB copyir.com Defective EEPROM copyir.com
0160 Backup memory data error (engine PWB) Defective flash memory copyir.com Defective engine PWB copyir.com
0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters copyir.com Data in the EEPROM copyir.com Defective PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data in the EEPROM copyir.com
0320 I/O CPU communication error
A communication error is detected 10 times in succession copyir.com Defective PWB copyir.com
0630 DMA error
DMA transmission of image data does not complete within the specified period of time copyir.com Poor contact in the connector terminals copyir.com Defective main PWB copyir.com
0800 Image processing error
The JAM100 fee counter is continuously generated copyir.com Defective main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com Defective FAX software copyir.com Defective FAX control PWB copyir.com
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com The battery is disconnected from the main PWB copyir.com Defective main PWB copyir.com
0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com Improper installation FAX control PWB copyir.com Defective FAX control PWB or main PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com Defective FAX control PWB copyir.com
1010 Lift motor error
After cassette 1 is inserted, the lift sensor does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the lift motor copyir.com Defective lift motor copyir.com Defective engine PWB copyir.com
1020 PF lift motor 1 error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the PF lift motor 1 copyir.com Defective PF lift motor 1 copyir.com Defective PF main PWB copyir.com
1030 PF lift motor 2 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system of the PF lift motor 2 copyir.com Defective PF lift motor 2 copyir.com Defective PF main PWB copyir.com
1800 Paper feeder communication error
A communication error is detected 10 times in succession copyir.com Improper installation of the paper feeder copyir.com Defective connector cable or poor contact of the connector copyir.com Defective engine PWB copyir.com Defective PF main PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, the write data and the read data is not continuously in agreement 4 times copyir.com Defective PF main PWB copyir.com Device damage of EEPROM copyir.com
1950 Transfer belt unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Defective transfer PWB copyir.com Device damage of EEPROM copyir.com
2101 Developer motor K steadystate error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor K stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2102 Developer motor YCM steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor YCM stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2111 Developer motor K startup error
Developer motor K is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2112 Developer motor YCM startup error
Developer motor YCM is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2201 Drum motor K steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the drum motor K stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2202 Drum motor YCM steadystate error
The rated speed signal detected the stability OFFcontinuously for 1 s after the drum motor YCM stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2211 Drum motor K startup error
Drum motor K is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2212 Drum motor YCM startup error
Drum motor YCM is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2300 Fuser motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the fuser motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2310 Fuser motor startup error
Fuser motor is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2550 Conveying motor steadystate error
The rated speed signal detected the stability OFF continuously for 1 s after the conveying motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2560 Conveying motor startup error
Conveying motor is not stabilized within 2 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2600 PF drive motor error (paper feeder)
When the PF drive motor is driven, error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
2700 TC belt motor error
When the TC belt motor is driven, error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
3100 ISU home position error
ON/OFF of the HP sensor doesn’t change by retrying, after a prescribed pulse passes from power supply ON copyir.com Defective connector cable or poor contact in the connector copyir.com Defective home position sensor copyir.com Defective ISU motor copyir.com Defective CCD PWB copyir.com Defective engine PWB copyir.com
3200 Exposure lamp error
The peak count during CCD turned on does not count up for 300 seconds copyir.com When the white standard data at the time of an initial is lower than a rated value copyir.com Defective connector cable or poor contact of the connector copyir.com Defective exposure lamp copyir.com Defective CCD PWB copyir.com Defective main PWB
3500 Communication error
A wrong read-back value copyir.com Defective connector cable or poor contact in the connector copyir.com Defective CCD PWB copyir.com Defective main PWB copyir.com
3600 Scanner sequence error Defective main PWB or engine PWB copyir.com
4001 Polygon motor (K) steadystate error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (K) stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective motor copyir.com Defective PWB copyir.com
4002 Polygon motor (C) steadystate error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (C) stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective motor copyir.com Defective PWB copyir.com
4003 Polygon motor (M) steadystate error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (M) stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective motor copyir.com Defective PWB copyir.com
4004 Polygon motor (Y) steadystate error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (Y) stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective motor copyir.com Defective PWB copyir.com
4011 Polygon motor (K) startup error
Polygon motor (K) is not stabilized within 10 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective motor copyir.com Defective PWB copyir.com
4012 Polygon motor (C) startup error
Polygon motor (C) is not stabilized within 10 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective motor copyir.com Defective PWB copyir.com
4013 Polygon motor (M) startup error
Polygon motor (M) is not stabilized within 10 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective motor copyir.com Defective PWB copyir.com
4014 Polygon motor (Y) startup error
Polygon motor (Y) is not stabilized within 10 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective motor copyir.com Defective PWB copyir.com
4101 BD initialization problem (K)
BD is not detected within one second after the polygon motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective APCPWB copyir.com Defective BDPWB copyir.com Defective Main PWB copyir.come?
4102 BD initialization problem (C)
BD is not detected within one second after the polygon motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective APCPWB copyir.com Defective BDPWB copyir.com Defective Main PWB copyir.com
4103 BD initialization problem (M)
BD is not detected within one second after the polygon motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective APCPWB copyir.com Defective BDPWB copyir.com Defective Main PWB copyir.com
4104 BD initialization problem (Y)
BD is not detected within one second after the polygon motor stabilizes copyir.com Defective connector cable or poor contact in the connector copyir.com Defective APCPWB copyir.com Defective BDPWB copyir.comPWB copyir.com Defective Main PWB copyir.com
4600 LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com Defective drive transmission system copyir.com Defective motor copyir.com Defective PWB copyir.com
4700 VIDEO ASIC device error Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Defective connector cable or poor contact in the connector copyir.com Defective main PWB or engine PWB copyir.com
4950 LSU CPU communication error
A communication error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com Defective PWB copyir.com
6000 Broken fuser heater wire
Fuser thermistor 2 does not reach 80° C/176 °F even after20 s during warming up copyir.com The detected temperature of fuser thermistor2 does not reach the specified temperature (ready indication temperature) for 200 s in warming up after reached to 80° C/176 °F copyir.com Defective connector cable or poor contact in the connector copyir.com Deformed connector pin copyir.com Defective IH PWB copyir.com Fuser thermostat triggered copyir.com Broken fuser heater wire copyir.com Defective engine PWB copyir.com
6020 Abnormally high fuser thermistor 2 (center) temperature
The fuser thermistor 2 detects a temperature higher than 240°C/464°F continuously for 1 s copyir.com Deformed connector pin copyir.com Shorted fuser thermistor copyir.com Defective engine PWB copyir.com
6030 Fuser thermistor 2 (center) break error
A/D value of the fuser thermistor 2 exceeds 1010 bit continuously for 1 s during warming up copyir.com Defective connector cable or poor contact in the connector copyir.com Deformed connector pin copyir.com Defective fuser thermistor copyir.com Defective engine PWB copyir.com
6040 NC sensor error
When a sensor detected the temperature higher than 150 °C/302 °F continuously for 5 seconds copyir.com Deformed connector pin copyir.com Shorted fuser thermistor copyir.com Defective engine PWB copyir.com
6050 Abnormally low fuser thermistor 2 (center) temperature
The fuser temperature lower than 100 °C/212 °F is detected continuously for 1 s during printing copyir.com Deformed connector pin copyir.com Defective fuser thermistor copyir.com Defective fuser heater copyir.com Defective engine PWB copyir.com
6120 Abnormally high fuser thermistor 3 (press roller) temperature
The fuser temperature exceeds 200 °C/392 °F for 1 s copyir.com Deformed connector pin copyir.com Defective IH PWB copyir.com Defective fuser thermistor copyir.com Defective engine PWB copyir.com
6130 Fuser thermistor 3 (press roller) break error
Fuser thermistor 3 does not reach 30° C/86 °F even after60 s during warming up copyir.com The detected temperature of fuser thermistor3 does not reach the specified temperature (ready indication temperature) for 200 s in warming up after reached to 30° C/86 °F copyir.com Defective connector cable or poor contact in the connector copyir.com Deformed connector pin copyir.com Defective IH PWB copyir.com Defective fuser thermistor copyir.com Defective engine PWB copyir.com
6150 Abnormally low fuser thermistor 3 (press roller) temperature
The fuser temperature lower than 30 °C/86 °F is detected continuously for 1 s copyir.com Deformed connector pin copyir.com Defective fuser thermistor copyir.com Defective fuser heater copyir.com Defective engine PWB copyir.com
6200 Broken fuser edge heater wire
Fuser thermistor 1 does not reach 50° C/122 °F even after20 s during warming up copyir.com The detected temperature of fuser thermistor1 does not reach the specified temperature (ready indication temperature) for 60 s in warming up after reaching 50° C/122 °F copyir.com Defective connector cable or poor contact in the connector copyir.com Deformed connector pin copyir.com Fuser thermostat triggered copyir.com Broken fuser heater wire copyir.com Defective engine PWB copyir.com
6220 Abnormally high fuser thermistor 1 (edge) temperature
The fuser temperature exceeds 240 °C/464 °F for 1 s copyir.com Deformed connector pin copyir.com Defective cooling fan motor copyir.com Defective fuser thermistor copyir.com Defective engine PWB copyir.com
6230 Fuser thermistor 1 (edge) break error
During warming up a hearter, fuser thermistor 2 detects a temperature of 100 °C/212 °F or higher and, fuser thermistor 1 detects a temperature of 37 °C/99 °F or lower copyir.com Defective connector cable or poor contact in the connector copyir.com Deformed connector pin copyir.com Defective fuser thermistor copyir.com Defective engine PWB copyir.com
6250 Abnormally low fuser thermistor 1 (edge) temperature
The fuser temperature lower than 80 °C/176 °F is detected continuously for 1 s during printing copyir.com Deformed connector pin copyir.com Defective IH PWB copyir.com Defective fuser thermistor copyir.com Defective fuser heater copyir.com Defective engine PWB copyir.com
6410 Fuser unit type mismatch problem
Absence of the fuser unit is detected copyir.com Fuser unit connector inserted incorrectly copyir.com Different type of the fuser unit is installed copyir.com
6600 Belt rotation error
The belt was detected to stop for 2 s continuously during motor remote is on copyir.com Defective fuser motor copyir.com Defective IH belt copyir.com Defective IH PWB copyir.com Defective engine PWB copyir.com
6710 CPU thermal runaway (IHPWB) Defective IH PWB copyir.com
6720 Belt rotation error (IHPWB) Defective IH PWB copyir.com Defective fuser motor copyir.com Defective fuser unit copyir.com
6730 Abnormally high IGBT1 temperature (IHPWB) Defective IH PWB copyir.com Defective cooling fan motor copyir.com
6740 Abnormally high IGBT2 temperature (IHPWB) Defective IH PWB copyir.com Defective cooling fan motor
6750 Abnormally output overcurrent (IHPWB) Defective IH PWB copyir.com Defective fuser unit
6760 Abnormally AC input overcurrent (IHPWB) Defective IH PWB copyir.com
6770 Abnormally low electric power (IHPWB) Defective connector cable or poor contact in the connector copyir.com Defective IH PWB copyir.com
6930 IH related cooling fan motor error
The alarm signal was detected for 5 seconds continuously during operation copyir.com Defective connector cable or poor contact in the connector copyir.com
6950 IH CPU communication error
A communication error is detected 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com Defective IH PWB copyir.com Defective engine PWB copyir.com
6990 Fuser unit type mismatch problem
Absence of the fuser unit is detected copyir.com Defective IH PWB copyir.com
7101 Toner sensor K error Defective Developer unit copyir.com Defective PWB copyir.com
7102 Toner sensor C error Defective Developer unit copyir.com Defective PWB copyir.com
7103 Toner sensor M error Defective Developer unit copyir.com Defective PWB copyir.com
7104 Toner sensor Y error Defective Developer unit copyir.com Defective PWB copyir.com
7601 ID sensor 1 (front) error Defective ID sensor copyir.com Defective PWB copyir.com
7602 ID sensor 2 (rear) errorr Defective ID sensor copyir.com Defective PWB copyir.com
7611 ID sensor (K) density error
When ID sensor 2 detected CTD is 500 or less copyir.com Defective ID sensor copyir.com Defective PWB copyir.com
7612 ID sensor (C) density error
When ID sensor 2 detected CTD is 500 or less copyir.com Defective ID sensor copyir.com Defective PWB copyir.com
7613 ID sensor (M) density error
When ID sensor 2 detected CTD is 500 or less copyir.com Defective ID sensor copyir.com Defective PWB copyir.com
7614 ID sensor (Y) density error
When ID sensor 2 detected CTD is 500 or less copyir.com Defective ID sensor copyir.com Defective PWB copyir.com
7620 ID sensor timing error
Color registration correction was failed Defective ID sensor copyir.com Defective PWB copyir.com
7800 Broken external thermistor wire
The external thermistor delivers 0 copyir.com3V or more copyir.comt time Defective connector cable or poor contact in the connector copyir.com Defective temperature sensor copyir.com
7810 Short-circuited external thermistor wire
external thermistor delivers 3V or more copyir.com Defective connector cable or poor contact in the connector copyir.com Defective temperature sensor copyir.com
7901 Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Poor contact in the connector terminals copyir.com Defective drum PWB copyir.com
7902 Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Poor contact in the connector terminals copyir.com Defective drum PWB copyir.com
7903 Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Poor contact in the connector terminals copyir.com Defective drum PWB copyir.com
7904 Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Poor contact in the connector terminals copyir.com Defective drum PWB copyir.com
7911 Developing unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Poor contact in the connector terminals copyir.com Defective developing PWB copyir.com
7912 Developing unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Poor contact in the connector terminals copyir.com Defective developing PWB copyir.com
7913 Developing unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Poor contact in the connector terminals copyir.com Defective developing PWB copyir.com
7914 Developing unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs eight times successively copyir.com Mismatch between writing data and reading data occurs eight times successively copyir.com Poor contact in the connector terminals copyir.com Defective developing PWB copyir.com
8030 Tray upper limit detection problem (document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected copyir.com Defective connector cable or poor contact in the connector copyir.com Defective tray upper limit sensor, paper surface sensor 1/2 copyir.com Defective DF main PWB copyir.com
8040 Belt problem (document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on copyir.com Defective connector cable or poor contact in the connector copyir.com Defective belt sensor copyir.com Defective belt solenoid copyir.com Defective DF main PWB copyir.com
8140 Tray elevation motor problem (document finisher)
The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com Defective connector cable or poor contact in the connector copyir.com The tray elevation motor malfunctions copyir.com Defective tray lower limit sensor, paper surface sensor 1/2 copyir.com Defective DF main PWB copyir.com
8210 Stapler problem (document finisher)
Jam 7012 or 7023 is indicated copyir.com Defective connector cable of staple or poor contact in the connector copyir.com The stapler is blocked with a staple copyir.com The stapler is broken copyir.com Defective DF main PWB copyir.com
8320 Adjustment motor 2 problem (document finisher)
The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on copyir.com Defective connector cable or poor contact in the connector copyir.com Defective adjustment sensor 2 copyir.com Defective adjustment motor 2 copyir.com Defective DF main PWB copyir.com
8330 Adjustment motor 1 problem (document finisher)
The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on copyir.com Defective connector cable or poor contact in the connector copyir.com Defective adjustment sensor 1 copyir.com Defective adjustment motor 1 copyir.com Defective DF main PWB copyir.com
8350 Roller motor problem (document finisher) The roller sensor does not turn on/off within specified time of the roller motor turning on copyir.com Defective connector cable or poor contact in the connector copyir.com Defective roller sensor copyir.com Defective roller motor copyir.com Defective DF main PWB copyir.com
8360 Slide motor problem (document finisher)
The slide sensor does not turn on/off within specified time of the slide motor turning on copyir.com Defective connector cable or poor contact in the connector copyir.com Defective slide sensor copyir.com Defective slide motor copyir.com Defective DF main PWB copyir.com
8460 EEPROM problem (document finisher)
Reading from or writing to EEPROM cannot be performed copyir.com Defective EEPROM or DF main PWB copyir.com
8800 Document finisher communication error
A communication error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com Defective DF main PWB copyir.com Defective engine PWB copyir.com
8830 Bridge communication error (document finisher)
A communication error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com Defective bridge PWB copyir.com Defective engine PWB copyir.com
8900 Backup memory data problem (document finisher)
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com EEPROM installed incorrectly copyir.com Defective finisher main PWB copyir.com
9000 Document processor communication error
A communication error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com Defective DP main PWB copyir.com
9060 DP EEPROM error
Mismatch between writing data and reading data occurs three times successively copyir.com Mismatch of reading data from two locations occurs three times successively copyir.com Defective DP main PWB copyir.com Device damage of EEPROM copyir.com
9500 copyir.com copyir.com copyir.com 9520 Contact the Service Administrative Division copyir.com
F000 Main PWB – operation panel PWB communication error Defective main PWB copyir.com Defective operation panel PWB copyir.com
F010 copyir.com copyir.com copyir.com F013 Main PWB checksum errorn Defective main PWB copyir.com
F040 Main PWB – print engine communication error Defective main PWB copyir.com Defective engine PWB copyir.com
F050 Print engine ROM checksum error Defective engine PWB copyir.comsu
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.