لمینت MKP
1402-06-04
Menu
C0030 Fax control PWB system problem (optional fax) Processing with the fax software was disabled due to a hardware or software problem copyir.com Defective fax control PWB copyir.com
C0060 Main PWB type mismatch error Defective PWB copyir.com
C0070 Abnormal detection of fax control PWB incompatibility (optional fax) In the initial communication with the fax control PWB, any normal communication command is not transmitted copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0100 Main PWB backup memory device problem Writing or erasing has not completed even after a certain time copyir.com Defective main PWB copyir.com
C0110 Backup memory data problem Data in the specified area of the backup memory does not match the specified values copyir.com Problem with the backup memory data copyir.com
C0120 Drum EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective drum unit copyir.com
C0130 Backup memory (EEPROM) device problem (Main PWB) Reading from or writing to EEPROM cannot be performed copyir.com Defective main PWB copyir.com Device damage of EEPROM copyir.com
C0140 Backup memory (EEPROM) data problem (Main PWB) Reading data from EEPROM is abnormal copyir.com Data damage of EEPROM copyir.com
C0150 Backup memory (EEPROM) device problem (Engine PWB) Reading from or writing to EEPROM cannot be performed copyir.com Defective engine PWB copyir.com Device damage of EEPROM copyir.com
C0160 Backup memory (EEPROM) data problem (Engine PWB) Reading data from EEPROM is abnormal copyir.com Read and write data does not match 5 times continuously copyir.com Problem with the backup memory data copyir.com Defective engine PWB copyir.com
C0170 Copy counts problem A checksum error is detected in the main and engine backup memories for the copy counters copyir.com Data damage of EEPROM copyir.com Defective PWB copyir.com
C0180 Machine number mismatch error Machine number of main PWB and engine PWB does not match copyir.com Data damage of EEPROM copyir.com
C0210 CPU communication problem There is no reply after 3 retries at communication copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0240 Printer PWB communication problem The printer PWB does not respond 120 s after the power is turned on copyir.com Poor contact in the connector terminals copyir.com DIMM or DDR installed incorrectly copyir.com Defective PWB copyir.com
C0280 Communication problem between the fax control PWB and main PWB After main PWB status change signal turns on 3 minute, when it does not receive key required command from the fax control PWB, one time it resets the FAX copyir.com After that, while main PWB status change signal turns on furthermore 1 minute, when it does not receive key required command from the fax control PWB copyir.com When FAX_READY signal continues fake for 6 s, one time it resets the FAX copyir.com After that, when FAX_READY fake continues fake for 6 s copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0320 Power CPU communication problem The engine PWB and the power CPU are unable to communicate with each other copyir.com Defective engine PWB copyir.com
C0420 Optional paper feeder communication problem The engine PWB and the paper feeder are unable to communicate with each other copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0440 Optional document finisher/built-in finisher communication problem The engine PWB and the document finisher or the built-in finisher are unable to communicate with each other copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0610 Bitmap problem The DIMM on the main PWB does not operate correctly copyir.com Defective main PWB copyir.com DDR on the main PWB installed incorrectly copyir.com
C0630 DMA problem DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time copyir.com Defective main PWB copyir.com DDR on the main PWB installed incorrectly copyir.com
C0800 Image processing problem JAM05 is detected twice copyir.com Defective main PWB copyir.com
C0820 Fax control PWB CG ROM checksum error (optional fax) A checksum error occurred with the CG ROM data of the fax control PWB copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0830 Fax control PWB flash program area checksum error (optional fax) A checksum error occurred with the program of the fax control PWB copyir.com Defective fax software copyir.comDefective fax control PWB copyir.com
C0860 Fax control PWB software switch checksum error (optional fax) A checksum error occurred with the software switch value of the fax control PWB copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0870 Fax control PWB to main PWB high capacity data transfer problem High-capacity data transfer between the fax control PWB and the scanner MIP PWB was not normally performed even if the data transfer was retried 10 times copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0880 Program archive problem (optional fax) When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0890 Fax control PWB CG FONT archive problem (optional fax) When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0920 Fax file system error The backup data is not retained for file system abnormality of flash memory of the fax control PWB copyir.com Defective fax control PWB copyir.com
C0960 Developing unit EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective developing unit copyir.com
C1010 Upper lift motor error When cassette 1 is inserted, upper lift limit switch does not turn on within 12 s of upper lift motor turning on copyir.com Poor contact in the connector terminals copyir.com Broken gears or couplings of upper lift motor copyir.com Defective upper lift motor copyir.com Defective upper lift limit switch copyir.com Poor contact in the connector terminals copyir.com Defective engine PWB copyir.com
C1020 Lower lift motor error When cassette 2 is inserted, lower lift limit switch does not turn on within 12 s of lower lift motor turning on copyir.com Poor contact in the connector terminals copyir.com Broken gears or couplings of lower lift motor copyir.com Defective lower lift motor copyir.com Defective lower lift limit switch copyir.com Poor contact in the connector terminals copyir.com Defective engine PWB copyir.com
C1030 Paper feeder lift motor 1 error (optional paper feeder) When optional cassette 3 is inserted, paper feeder lift switch 1 does not turn on within 12 s of paper feeder lift motor 1 turning on copyir.com Poor contact in the connector terminals copyir.com Broken gears or couplings of paper feeder lift motor 1 copyir.com Defective paper feeder lift motor 1 copyir.com Defective paper feeder lift switch 1 copyir.com
C1040 Paper feeder lift motor 2 error (optional paper feeder) When optional cassette 4 is inserted, paper feeder lift switch 2 does not turn on within 12 s of paper feeder lift motor 2 turning on copyir.com Poor contact in the connector terminals copyir.com Broken gears or couplings of paper feeder lift motor 2 copyir.com Defective paper feeder lift motor 2 copyir.com Defective paper feeder lift switch 2 copyir.com
C2000 Main motor problem Stable OFF is detected for 1 s continuously after main motor stability copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective engine PWB copyir.com
C2200 Drum motor problem Stable OFF is detected for 1 s continuously after drum motor stability copyir.com Defective main motor copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective engine PWB copyir.com Defective drum motor copyir.com
C2500 Paper feed motor error Stable OFF is detected for 1 s continuously after paper feed motor stability copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective engine PWB copyir.com Defective paper feed motor copyir.com
C2600 Paper feeder drive motor error (optional paper feeder) The lock signal of the motor is detected avobe 500 ms copyir.com Poor contact in the connector terminals copyir.com Paper feeder drive motor does not rotate correctly (the motor is overloaded) copyir.com Defective PWB copyir.com Defective paper feeder drive motor copyir.com
C3100 Scanner carriage problem The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Poor contact in the connector terminals copyir.com Defective scanner home position switch copyir.com Defective scanner motor copyir.com The mirror frame, exposure lamp, or scanner wire is defective copyir.com Defective engine PWB copyir.com
C3200 Exposure lamp problem After the reading starting, when input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s copyir.com Poor contact in the connector terminals copyir.com Defective exposure lamp copyir.com Incorrect shading position copyir.com Defective PWB copyir.com
C3300 CCD AGC problem After AGC, correct input is not obtained at CCD copyir.com Poor contact in the connector terminals copyir.com Defective exposure lamp copyir.com Defective PWB copyir.com
C4000 Polygon motor synchronization problem The polygon motor does not reach the stable speed within 20 s of the START signal turning on copyir.com Poor contact in the connector terminals copyir.com Defective polygon motor copyir.com Defective engine PWB copyir.com
C4010 Polygon motor steady-state problem Stable OFF is detected for 5 s continuously after polygon motor stability copyir.com Poor contact in the connector terminals copyir.com Defective polygon motor copyir.com Defective engine PWB copyir.com
C4200 BD steady-state problem ASIC detects a BD error for 1 s after the polygon motor rotation has been stabilized copyir.com Poor contact in the connector terminals copyir.com Defective laser scanner unit copyir.com Defective engine PWB copyir.com
C6000 Fuser heater break Fuser thermistor 1 detected less than 40C/104F for 10 s during warm-up and ready in copyir.com Defective fuser heater M or S copyir.com Installation defectiveness on fuser thermistor 1 copyir.com Defective fuser thermostat copyir.com Defective PWB copyir.com
C6020 Abnormally high fuser thermistor center temperature Fuser thermistor 2 is detected 230C/ 446F or more for 40 ms copyir.com Installation defectiveness on fuser thermistor 2 copyir.com Defective fuser thermistor 2 copyir.com Defective engine PWB copyir.com
C6050 Abnormally low fuser thermistor center temperature Fuser thermistor 2 is detected 100C/ 212F less than 1 s continuously during copying copyir.com Defective fuser heater M or S copyir.com Installation defectiveness on fuser thermistor 2 copyir.com Defective PWB copyir.com
C6120 Abnormally high fuser thermistor edge temperature Fuser thermistor 1 is detected 230C/ 446F or more for 40 ms copyir.com Installation defectiveness on fuser thermistor 1 copyir.com Defective fuser thermistor 1 copyir.com Defective engine PWB copyir.com
C6150 Abnormally low fuser thermistor edge temperature Fuser thermistor 1 is detected 100C/ 212F less than 1 s continuously during copying copyir.com Defective fuser heater M or S copyir.com Installation defectiveness on fuser thermistor 1 copyir.com Defective PWB copyir.com
C6400 Zero-cross signal error While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 3 s copyir.com Defective PWB copyir.com
C6420 Fuser unit fuse cut problem The fuse cannot be cut, When replacing the fuser unit, the fuse cannot be cut in 3 s after the fuse cut signal is turned on copyir.com Poor contact in the connector terminals copyir.com Fuser unit connector inserted incorrectly copyir.com
C7000 Toner motor problem A motor over-current signal is detected continuously for 1 s or longer copyir.com Poor contact in the connector terminals copyir.com Broken the gear copyir.com Defective toner feed motor copyir.com Defective engine PWB copyir.com
C7200 Broken inner thermistor wire An abnormal value is detected in the input data to inner thermistor copyir.com Poor contact in the connector terminals copyir.com Defective temperature sensor copyir.com
C7300 Toner hopper problem Toner emptiness is detected for 300 s, three times during the toner replenishment copyir.com Poor contact in the connector terminals copyir.com Defective toner sensor copyir.com
C7400 Developing unit connector insertion problem Absence of the developing unit is detected copyir.com Developing unit connector inserted incorrectly copyir.com Defective developing unit connector copyir.com
C7410 Drum unit connector insertion problem Absence of the drum unit is detected copyir.com Drum unit connector inserted incorrectly copyir.com Defective drum unit connector copyir.com
C7800 Broken external thermistor wire The thermistor output value is 4 copyir.com5 V or more copyir.com Poor contact in the connector terminals copyir.com Defective humidity sensor copyir.com
C8030 Tray upper limit detection problem (optional document finisher) When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected copyir.com The tray upper limit sensor/push paper sensor/surface view sensor connector makes poor contact copyir.com Defective tray upper limit sensor/ push paper sensor/ surface view sensor copyir.com Defective finisher main PWB copyir.com
C8140 Tray elevation motor problem (optional document finisher) When the tray elevation motor is driving, the ON status of the tray lower limit sensor or surface view sensor cannot be detected even if 20 s passed copyir.com The tray elevation motor connector makes poor contact copyir.com The tray elevation motor malfunctions copyir.com The tray lower limit sensor/push paper sensor/surface view sensor connector makes poor contact copyir.com Defective tray lower limit sensor/ push paper sensor/ surface view sensor copyir.com Defective finisher main PWB copyir.com
C8170 Adjustment motor problem (optional document finisher) When the adjustment motor is driving, the ON status of the adjustment home position sensor cannot be detected even if a specified time has elapsed copyir.com When adjustment operation starts, the ON status of the adjustment home position sensor is not detected copyir.com The adjustment motor connector makes poor contact copyir.com Defective adjustment motor copyir.com The adjustment home position sensor connector makes poor contact copyir.com Defective adjustment home position sensor copyir.com Defective finisher main PWB copyir.com
C8170 Finisher front side registration motor problem (optional built-in finisher) When the front-side registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses copyir.com When the front-side registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s copyir.com The front side registration motor connector makes poor contact copyir.com Defective front side registration motor copyir.com The front side registration home position sensor connector makes poor contact copyir.com Defective front side registration home position sensor copyir.com Defective finisher control PWB copyir.com
C8180 Finisher rear side registration motor problem (optional built-in finisher) When the rear-side registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses copyir.com When the rear-side registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s copyir.com The rear side registration motor connector makes poor contact copyir.com Defective rear side registration motor copyir.com The rear side registration home position sensor connector makes poor contact copyir.com Defective rear side registration home position sensor copyir.com Defective finisher control PWB copyir.com
C8190 Finisher trailing edge registration motor problem (optional built-in finisher) When the trailing edge registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses copyir.com When the trailing edge registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s copyir.com The trailing edge registration motor connector makes poor contact copyir.com Defective trailing edge registration motor copyir.com The trailing edge registration home position sensor connector makes poor contact copyir.com Defective trailing edge registration home position sensor copyir.com Defective finisher control PWB copyir.com
C8210 Stapler problem (optional document finisher) When the stapler motor is driving, the ON status of the stapler home position sensor cannot be detected even if a specified time has elapsed copyir.com The stapler connector makes poor contact copyir.com The stapler is blocked with a staple copyir.com The stapler is broken copyir.com Defective finisher main PWB copyir.com
C8210 Finisher stapler problem (optional built-in finisher) The stapler home position sensor does not change state from nondetection to detection within 200 ms of the start of stapler motor counterclockwise (forward) rotation copyir.com During initialization, the stapler home position sensor does not change state from non-detection to detection within 600 ms of the start of stapler motor clockwise (reverse) rotation copyir.com The stapler connector makes poor contact copyir.com The stapler is blocked with a staple copyir.com The stapler is broken copyir.com Defective finisher control PWB copyir.com
C8440 Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range copyir.com The paper entry sensor connector makes poor contact copyir.com Defective paper entry sensor copyir.com The optical path of the paper entry sensor is blocked by foreign matter copyir.com Defective finisher main PWB copyir.com
C8460 EEPROM problem (optional document finisher) Reading from or writing to EEPROM cannot be performed copyir.com Defective EEPROM or finisher main PWB copyir.com
C9000 Optional DP communication problem A communication error is detected copyir.com Poor contact in the connector terminals copyir.com Defective DP main PWB copyir.com
C9060 DP EEPROM error (optional DP) Read and write data does not match copyir.com Data in the specified area of the backup memory does not match the specified values copyir.com Defective DP main PWB copyir.com Device damage of EEPROM copyir.com
F000 Operation panel PWB communication error Defective main PWB copyir.com Defective operation panel PWB copyir.com
F010 Main PWB checksum error Defective main PWB copyir.com
F020 Memory checksum error Defective main PWB copyir.com Defective expansion memory copyir.com
F030 Main PWB system error Defective main PWB copyir.com
F040 Engine PWB communication error Defective main PWB copyir.com Defective engine PWB copyir.com
F041 Scanner communication error Defective main PWB copyir.com
F050 Engine ROM checksum error Defective engine PWB copyir.com
F060 Engine RAM error Defective engine PWB copyir.com
F070 Flash ROM error Defective flash ROM copyir.com
F080 Flash ROM error (during download) Defective flash ROM copyir.com
F090 Fax control PWB communication error Defective main PWB copyir.com
F14F Power source PWB secondary side error Defective power source PWB copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.