کیو سرا میتا km4800w

کیو سرا میتا km4800w

E000    Fuser Temperature Rising Error
The temperature of Fuser does not rise up to 50C       copyir       copyir.comcom
E001    Fuser Over Temperature Error
The temperature of fuser rises over 230C
E002    Fuser Low Temperature Error
1       copyir       copyir.comcom The temperature of fuser at the time of turning on was 50 to 100C       copyir       copyir.comcom but it does not rise up to 100C within 80 seconds after that       copyir       copyir.comcom 2       copyir       copyir.comcom The temperature of fuser at the time of turning on was higher than 100C       copyir       copyir.comcom but it does not rise up to the setting temperature within 150 seconds after that       copyir       copyir.comcom
E003    Fuser Temperature Abnormal Fall Error
The difference of temperature between center and side of fuser becomes 50C or more       copyir       copyir.comcom
E004    Fuser Temperature Abnormal Fall Error
The Lamp of fuser lights (Signal HEAT1 is “H”       copyir       copyir.comcom to heat up the Fuser Roller in the ready condition       copyir       copyir.comcom but even 1C of temperature rise can not be accomplished within 15 seconds       copyir       copyir.comcom
E010    Main Motor Error
The Main Motor Output Detection Signal (MAINM_LD       copyir       copyir.comcom continues to be “H” for 3 seconds or longer when the Main Motor is rotating       copyir       copyir.comcom
E011    Fuser Motor Error
The Fuser Motor Output Detection Signal (HEATM_LD       copyir       copyir.comcom continues to be “H” for 3 seconds or longer when the Fuser Motor is rotating       copyir       copyir.comcom
E012    Developer Press Motor Error
The Developer Press Sensor Signal (PRESS_S       copyir       copyir.comcom does not change to “L” within 30 seconds after turning on       copyir       copyir.comcom
E020    Counter Error
The Counter Connection Detection Signal (COUNT_OPN       copyir       copyir.comcom continues to be “L” for 1 second or longer after turning on       copyir       copyir.comcom
E031    Image Corona Output Error
The Image Corona Output Detection Signal (IM_LD       copyir       copyir.comcom continues to be “L” for 1 second or longer when the Image Corona is ON       copyir       copyir.comcom
E032    Separation Corona Output Error
The Separation Corona Output Detection Signal (AC_LD       copyir       copyir.comcom continues to be “L” for 1 second or longer when the Separation Corona is ON       copyir       copyir.comcom
E033    Transfer Corona Output Error
The Transfer Corona Output Detection Signal (TR_LD       copyir       copyir.comcom continues to be “L” for 1 second or longer when the Transfer Corona is ON       copyir       copyir.comcom
E034    Developer Bias Output Error
The Developer Bias Output Detection Signal (BIAS_LD       copyir       copyir.comcom continues to be “L” for 1 second or longer when the Developer Bias is supplied to the Developer Unit       copyir       copyir.comcom
E040    Cutter Error
1       copyir       copyir.comcom The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R       copyir       copyir.comcom does not change to “H” within 100 millisecond since the Cutter has started the operation       copyir       copyir.comcom 2       copyir       copyir.comcom The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R       copyir       copyir.comcom does not change to “L” within 1 second since the Cutter has started the operation       copyir       copyir.comcom
E050    FPGA Error
Initialization of FPGA is failed after turning on       copyir       copyir.comcom
E070    Developer Error
1       copyir       copyir.comcom The Connector J-253 is not connected       copyir       copyir.comcom 2       copyir       copyir.comcom The Switch (MS4       copyir       copyir.comcom is “open” condition       copyir       copyir.comcom which detects open/close of Engine Unit or Toner Hatch       copyir       copyir.comcom
E080    Density Sensor Error
The default output of Density Sensor reaches less than 0       copyir       copyir.comcom1V or more than 1       copyir       copyir.comcom3V       copyir       copyir.comcom
E081    Density Sensor Output Error
The gap between the default output and the standard output of Density Sensor reaches less than 2V       copyir       copyir.comcom
E000    Fuser Temperature Rising Error
The temperature of Fuser does not rise up to 50C       copyir       copyir.comcom
E001    Fuser Over Temperature Error
The temperature of fuser rises over 230C
E002    Fuser Low Temperature Error
1       copyir       copyir.comcom The temperature of fuser at the time of turning on was 50 to 100C       copyir       copyir.comcom but it does not rise up to 100C within 80 seconds after that       copyir       copyir.comcom 2       copyir       copyir.comcom The temperature of fuser at the time of turning on was higher than 100C       copyir       copyir.comcom but it does not rise up to the setting temperature within 150 seconds after that       copyir       copyir.comcom
E003    Fuser Temperature Abnormal Fall Error
The difference of temperature between center and side of fuser becomes 50C or more       copyir       copyir.comcom
E004    Fuser Temperature Abnormal Fall Error
The Lamp of fuser lights (Signal HEAT1 is “H”       copyir       copyir.comcom to heat up the Fuser Roller in the ready condition       copyir       copyir.comcom but even 1C of temperature rise can not be accomplished within 15 seconds       copyir       copyir.comcom
E010    Main Motor Error
The Main Motor Output Detection Signal (MAINM_LD       copyir       copyir.comcom continues to be “H” for 3 seconds or longer when the Main Motor is rotating       copyir       copyir.comcom
E011    Fuser Motor Error
The Fuser Motor Output Detection Signal (HEATM_LD       copyir       copyir.comcom continues to be “H” for 3 seconds or longer when the Fuser Motor is rotating       copyir       copyir.comcom
E012    Developer Press Motor Error
The Developer Press Sensor Signal (PRESS_S       copyir       copyir.comcom does not change to “L” within 30 seconds after turning on       copyir       copyir.comcom
E020    Counter Error
The Counter Connection Detection Signal (COUNT_OPN       copyir       copyir.comcom continues to be “L” for 1 second or longer after turning on       copyir       copyir.comcom
E031    Image Corona Output Error
The Image Corona Output Detection Signal (IM_LD       copyir       copyir.comcom continues to be “L” for 1 second or longer when the Image Corona is ON       copyir       copyir.comcom
E032    Separation Corona Output Error
The Separation Corona Output Detection Signal (AC_LD       copyir       copyir.comcom continues to be “L” for 1 second or longer when the Separation Corona is ON       copyir       copyir.comcom
E033    Transfer Corona Output Error
The Transfer Corona Output Detection Signal (TR_LD       copyir       copyir.comcom continues to be “L” for 1 second or longer when the Transfer Corona is ON       copyir       copyir.comcom
E034    Developer Bias Output Error
The Developer Bias Output Detection Signal (BIAS_LD       copyir       copyir.comcom continues to be “L” for 1 second or longer when the Developer Bias is supplied to the Developer Unit       copyir       copyir.comcom
E040    Cutter Error
1       copyir       copyir.comcom The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R       copyir       copyir.comcom does not change to “H” within 100 millisecond since the Cutter has started the operation       copyir       copyir.comcom 2       copyir       copyir.comcom The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R       copyir       copyir.comcom does not change to “L” within 1 second since the Cutter has started the operation       copyir       copyir.comcom
E050    FPGA Error
Initialization of FPGA is failed after turning on       copyir       copyir.comcom
E070    Developer Error
1       copyir       copyir.comcom The Connector J-253 is not connected       copyir       copyir.comcom 2       copyir       copyir.comcom The Switch (MS4       copyir       copyir.comcom is “open” condition       copyir       copyir.comcom which detects open/close of Engine Unit or Toner Hatch       copyir       copyir.comcom
E080    Density Sensor Error
The default output of Density Sensor reaches less than 0       copyir       copyir.comcom1V or more than 1       copyir       copyir.comcom3V       copyir       copyir.comcom
E081    Density Sensor Output Error
The gap between the default output and the standard output of Density Sensor reaches less than 2V       copyir       copyir.comcom