لمینت MKP
1402-06-04
Menu
0030 FAX control PWB system error
Processing with the fax software was disabled due to a software problem copyir.com FAX control PWB copyir.com
0060 Control PWB mismatch
Unmatching engine and engine sub boards copyir.com Defective engine subboard Control PWB
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com FAX control PWB (The FAX PWB installed will not be the one designed for the machine copyir.com
0100 Backup memory device error EEPROM (Control PWB)
0110 Backup memory data error EEPROM (Control PWB)
0120 MAC address data error
For data in which the MAC address is invalid copyir.com EEPROM (Control PWB)
0130 Backup memory read/write error (main NAMD) Flash memory (Control PWB)
0140 Backup memory data error (main NAND) Flash memory (Control PWB)
0150 Backup memory read/write error (control PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com EEPROM (Control PWB)
0160 Backup memory data error (control PWB)
Reading data from EEPROM is abnormal copyir.com EEPROM
0170 Billing counting error
The values on the main circuit PWB and on the engine do not match for any of charging counter, life counter, and scanner counter copyir.com EEPROM copyir.com Control PWB
0180 Machine number mismatch
Machine number of control does not match copyir.com Data damage of EEPROM copyir.com
0190 Backup memory device error (control PWB) Control PWB
0800 Image processing error
JAM010X is detected twice copyir.com Control PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com FAX software copyir.com FAX control PWB copyir.com
0840 Faults of RTC (“Time for maintenance T” is displayed) [Check at power up]
The RTC setting has reverted to a previous state copyir.com The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM) copyir.com The RTC setting is older than 00:01 on January 1, 2000 copyir.com [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked copyir.com 10 minutes have been passed since the previous check copyir.com Battery (Control PWB) copyir.com Control PWB copyir.com
0870 PCFAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com FAX control PWB copyir.com Control PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com FAX control PWB copyir.com
0970 24 V power down detect
If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second copyir.com Connect right PWB copyir.com Control PWB
1010 Lift motor error (50/60 ppm model only)
After cassette 1 is inserted, lift sensor does not turn on within 10 s copyir.com This error is detected four times successively copyir.com Bottom plate elevation mechanism in the cassette copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the lift motor copyir.com Lift motor copyir.com Connect right PWB copyir.com Control PWB copyir.com
1020 PF lift motor 1 error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on copyir.com This error is detected four times successively copyir.com Bottom plate elevation mechanism in the cassette copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the PF lift motor copyir.com PF lift motor copyir.com PF main PWB copyir.com
1030 PF lift motor 2 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on copyir.com This error is detected four times successively copyir.com Dottom plate elevation mechanism in the cassette copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the PF lift motor copyir.com PF lift motor copyir.com PF main PWB copyir.com
1040 PF lift motor 3 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 3 does not turn on copyir.com This error is detected four times successively copyir.com Bottom plate elevation mechanism in the cassette copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the PF lift motor copyir.com PF lift motor copyir.com PF main PWB copyir.com
1050 PF lift motor 4 error (paper feeder)
After cassette 5 is inserted, PF lift sensor 4 does not turn on copyir.com This error is detected four times successively copyir.com Bottom plate elevation mechanism in the cassette copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the PF lift motor copyir.com PF lift motor copyir.com PF main PWB copyir.com
1800 Paper feeder 1 communication error
A communication error is detected 10 times in succession copyir.com Paper feeder copyir.com Connector cable or poor contact in the connector copyir.com PF main PWB copyir.com Control PWB copyir.com
1810 Paper feeder 2 communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Paper feeder copyir.com PF main PWB copyir.com Control PWB copyir.com
1820 Paper feeder 3 communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Paper feeder copyir.com PF main PWB copyir.com Control PWB
1830 Paper feeder 4 communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Paper feeder copyir.com PF main PWB copyir.com Control PWB
1900 Paper feeder 1 EEPROM error
When writing the data, read and write data does not match 4 times in succession copyir.com PF main PWB (EEPROM)
1910 Paper feeder 2 EEPROM error
When writing the data, read and write data does not match 4 times in succession copyir.com PF main PWB (EEPROM)
1920 Paper feeder 3 EEPROM error
When writing the data, read and write data does not match 4 times in succession copyir.com PF main PWB (EEPROM)
1930 Paper feeder 4 EEPROM error
When writing the data, read and write data does not match 4 times in succession copyir.com PF main PWB (EEPROM)
2000 Main motor startup error
Main motor is not stabilized within 2 s since the motor is activated copyir.com Main motor copyir.com Connect right PWB copyir.com Control PWB
2010 Main motor steady-state error
After main motor is stabilized, the ready signal is not ready for 2 s continuously copyir.com Main motor copyir.com Connect right PWB copyir.com Control PWB copyir.com
2200 Drum motor drive error (50/60 ppm model only)
The drum motor is not stabilized within 2 s after driving starts copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the drum motor copyir.com Drum motor copyir.com Connect right PWB copyir.com Control PWB copyir.com
2210 Drum motor steady-state error (50/60 ppm model only)
Stable OFF is detected for 2 s continuously after drum motor stabilized copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the drum motor copyir.com Drum motor copyir.com Connect right PWB copyir.com Control PWB copyir.com
2330 Envelope motor error (Over-current) (50/60 ppm model only)
The over-current detection signal of the motor is detected continuously twenty times copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the envelope motor copyir.com Envelope motor copyir.com Connect left PWB copyir.com Control PWB copyir.com
2340 Envelope motor error (Timeout) (50/60 ppm model only)
The position detection sensor is not detected continuously for 30 s copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the envelope motor copyir.com Envelope motor copyir.com Connect left PWB copyir.com Control PWB copyir.com
2600 PF drive motor 1 error (paper feeder 1)
When the PF drive motor is driven, error signal is detected continuously for 2 s copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the PF drive motor copyir.com DPF drive motor copyir.com DPF main PWB copyir.com
2610 PF drive motor 2 error (paper feeder 2)
When the PF drive motor is driven, error signal is detected continuously for 2 s copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the PF drive motor copyir.com PF drive motor copyir.com PF main PWB copyir.com
2620 PF drive motor 3 error (paper feeder 3)
When the PF drive motor is driven, error signal is detected continuously for 2 s copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the PF drive motor copyir.com PF drive motor copyir.com PF main PWB copyir.com
2630 PF drive motor 4 error (paper feeder 4)
When the PF drive motor is driven, error signal is detected continuously for 2 s copyir.com Connector cable or poor contact in the connector copyir.com Drive transmission system of the PF drive motor copyir.com PF drive motor copyir.com PF main PWB copyir.com
3100 Scanner carriage error
The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor copyir.com Image scanner motor copyir.com Home position sensor copyir.com CCD PWB copyir.com Control PWB copyir.com
3200 Exposure lamp error
When a lamp is made to turn on one side at a time, the white standard data at the time of an initial is lower than a rated value copyir.com LED PWB copyir.com CCD PWB copyir.com Control PWB copyir.com
3500 Communication error between scanner and ASIC
An error code is detected copyir.com CCD PWB copyir.com Control PWB copyir.com
4000 Polygon motor steady-state error
After Polygon motor is stabilized, the ready signal is at the H level for 20 s continuously copyir.com Polygon motor (LSU) copyir.com Control PWB copyir.com
4200 BD steady-state error
The BD signal is not detected copyir.com PD PWB (LSU) copyir.com Control PWB copyir.com
5100 Chager current error When the current value measured at the time of potential adjustment is less than 20 mcA copyir.com The error of the charge current before toner installation copyir.com The error of the charge current before printing copyir.com Connector cable or poor contact in the connector copyir.com High voltage PWB copyir.com Control PWB copyir.com
6000 Broken fuser heater wire (Center)
(50/60 ppm model) Fuser thermistor 2 detects a temperature less than 100°C/ 212°F continuously for 30 s after a warm-up start copyir.com (40 ppm model) Fuser thermistor 1 detects a temperature less than 100°C/ 212°F continuously for 30 s after a warm-up start copyir.com Fuser unit copyir.com Fuser thermistor connect PWB copyir.com Control PWB copyir.com Power source PWB copyir.com Fuser heater copyir.com
6020 Abnormally high fuser thermistor 2 temperature (Center)
(50/60 ppm model only) Fuser thermistor 2 detects a temperature higher than 235°C/455°F copyir.com In a heater-off state, the detection temperature of fuser thermistor 2 is higher than 195°C/383°F after the detection temperature of fuser thermistor 2 was 155°C/311°F or less copyir.com Fuser unit copyir.com Fuser thermistor connect PWB copyir.com Control PWB copyir.com
6030 Broken fuser thermistor 2 wire (Center)
(50/60 ppm model only) Input from fuser thermistor 2 is 1019 or more (A/D value) continuously for 4 s copyir.com Fuser unit copyir.com Fuser thermistor connect PWB copyir.com Control PWB copyir.com Fuser thermistor 2 copyir.com Fuser thermostat (triggered) copyir.com Power source PWB
6120 Abnormally high fuser thermistor 1 temperature
(50/60 ppm model) The detection temperature of fuser thermistor 1 is higher than 245°C/473°F copyir.com In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 195°C/383°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less copyir.com (40 ppm model) The detection temperature of fuser thermistor 1 is higher than 250°C/482°F copyir.com In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 170°C/338°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less copyir.com Connector pin copyir.com Triac copyir.com Fuser thermistor copyir.com Contrl PWB copyir.com
6130 Broken fuser thermistor 1 wire (50/60 ppm model only)
A/D value of the fuser thermistor 1 exceeds 1019 bit continuously for 4 s during warming up copyir.com Connector cable or poor contact in the connector copyir.com Connector pin copyir.com Triac copyir.com Fuser thermistor copyir.com Fuser thermistor connect PWB copyir.com Control PWB copyir.com
6400 Zero-cross signal error
While fuser heater ON/OFF control is performed, the zerocross signal is not input within 2 s copyir.com Fuser unit copyir.com Power source PWB copyir.com Connect right PWB copyir.com Control PWB copyir.com
7000 Toner motor error
During driving the toner motor, an over-current detection signal is detected at intervals of 10 ms as for 300 accumulation copyir.com Connector cable or poor contact in the connector copyir.com Drum unit copyir.com Connect left PWB copyir.com Control PWB copyir.com
7100 Toner sensor error
Sensor output value of 930 or more continuously for 5 s copyir.com Toner sensor copyir.com Toner motor copyir.com Connect left PWB copyir.com Control PWB copyir.com
7400 Developer unit non-installing error
Sensor output value of 31 or less continuously for 5 s copyir.com Connector cable or poor contact in the connector copyir.com Toner sensor copyir.com Connect left PWB copyir.com Control PWB copyir.com
7410 Drum unit type mismatch error
The drum PWB EEPROM does not communicate normally copyir.com Absence of the drum unit is detected copyir.com Connector cable or poor contact in the connector copyir.com Toner sensor copyir.com Connect left PWB copyir.com Control PWB copyir.com
7800 Broken temperature sensor wire
Input from temperature sensor is 1019 or more continuously for 160 ms copyir.com Input from temperature sensor is 930 or more continuously for 5 s copyir.com Temperature sensor copyir.com Control PWB copyir.com
7810 Short-circuited temperature sensor wire
Input from temperature sensor is 31 or less continuously for 5 s copyir.com Temperature sensor copyir.com Control PWB copyir.com
7900 Drum EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com DR PWB copyir.com Connect left PWB copyir.com Control PWB copyir.com
F000 Communication error between Control PWB and Operation PWB Control PWB copyir.com Operation PWB copyir.com
F010 Control PWB checksum error Control PWB copyir.com
F020 Control PWB RAM check sum error Main memory (RAM) copyir.com
F040 Communication error between Controller and Print engine Control PWB copyir.com
F041 Communication error between Controller and Scan engine Control PWB copyir.com
F050 Print engine ROM checksum error Control PWB copyir.com
F051 Scan engine ROM checksum error Control PWB
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.