کیو سرا میتا p6026cdn

0100    Backup memory device error    Defective flash memory      copyir.com Defective main PWB      copyir.com
0120    MAC address data error
For data in which the MAC address is invalid      copyir.com    Defective flash memory      copyir.com Defective engine PWB      copyir.com
0130    Backup memory read/write error (main PWB)    Defective flash memory      copyir.com Defective main PWB      copyir.com
0140    Backup memory data error (main PWB)    Defective flash memory      copyir.com Defective main PWB      copyir.com
0150    Engine PWB EEPROM error
Detecting engine PWB EEPROM communication error      copyir.com    Improper installation engine PWB EEPROM      copyir.com Defective engine PWB      copyir.com Device damage of EEPROM      copyir.com
0170    Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters      copyir.com    Data damage of EEPROM      copyir.com Defective PWB      copyir.com
0600    Expanded memory (DIMM) installing error
The expansion memory modules (DIMM) are not correctly mounted      copyir.com    Improper installation expanded memory (DIMM)      copyir.com
0610    Expanded memory (DIMM) error
The expansion memory modules (DIMM) mounted on the main PWB does not operate correctly      copyir.com    Defective expanded memory (DIMM)      copyir.com Defective main PWB      copyir.com
0640    SSD error
The SSD cannot be accessed      copyir.com    Defective SSD      copyir.com Defective main PWB      copyir.com
0840    Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed      copyir.com    The battery is disconnected from the main PWB      copyir.com Defective main PWB      copyir.com
0930    EEPROM bus error    Defective drum PWB (EEPROM)      copyir.com Defective engine PWB (EEPROM)      copyir.com Defective engine PWB      copyir.com Defective main PWB      copyir.comOM      copyir.com
1010    Lift motor error
When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals      copyir.com After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s      copyir.com The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively      copyir.com    Defective bottom plate elevation mechanism in the cassette      copyir.com Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the lift motor      copyir.com Defective lift motor      copyir.com Defective engine PWB      copyir.com
1020    PF lift motor error (paper feeder 1)
When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals      copyir.com After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s      copyir.com The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively      copyir.com    Defective bottom plate elevation mechanism in the cassette      copyir.com Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the PF lift motor      copyir.com Defective PF lift motor      copyir.com Defective PF main PWB      copyir.com
1030    PF lift motor error (paper feeder 2)
When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals      copyir.com After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s      copyir.com The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively      copyir.com    Defective bottom plate elevation mechanism in the cassette      copyir.com Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the PF lift motor      copyir.com Defective PF lift motor      copyir.com Defective PF main PWB      copyir.com
1040    PF lift motor error (paper feeder 3)
When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals      copyir.com After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s      copyir.com The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively      copyir.com    Defective bottom plate elevation mechanism in the cassette      copyir.com Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the PF lift motor      copyir.com Defective PF lift motor      copyir.com Defective PF main PWB      copyir.com
1500    PF heater 1 high temperature error (paper feeder 1)
A temperature higher than 75C/167F is detected      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Shorted PF thermistor 1      copyir.com Defective PF fan motor 1      copyir.com Defective PF main PWB      copyir.com
1510    PF heater 2 high temperature error (paper feeder 1)
A temperature higher than 75C/167F is detected      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Shorted PF thermistor 2      copyir.com Defective PF fan motor 2      copyir.com Defective PF main PWB      copyir.com
1520    PF heater 1 high temperature error (paper feeder 2)
A temperature higher than 75C/167F is detected      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Shorted PF thermistor 1      copyir.com Defective PF fan motor 1      copyir.com Defective PF main PWB      copyir.com
1530    PF heater 2 high temperature error (paper feeder 2)
A temperature higher than 75C/167F is detected      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Shorted PF thermistor 2      copyir.com Defective PF fan motor 2      copyir.com Defective PF main PWB      copyir.com
1540    PF heater 1 high temperature error (paper feeder 3)
A temperature higher than 75C/167F is detected      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Shorted PF thermistor 1      copyir.com Defective PF fan motor 1      copyir.com Defective PF main PWB      copyir.com
1550    PF heater 2 high temperature error (paper feeder 3)
A temperature higher than 75C/167F is detected      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Shorted PF thermistor 2      copyir.com Defective PF fan motor 2      copyir.com Defective PF main PWB      copyir.com
1600    PF heater 1 low temperature error (paper feeder 1)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on      copyir.com    Defective connector cable or poor contact in the connector      copyir.com PF thermistor 1 installed incorrectly      copyir.com Defective PF thermistor 1      copyir.com Broken PF heater 1      copyir.com Defective PF heater PWB or PF main PWB      copyir.com
1610    PF heater 2 low temperature error (paper feeder 1)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on      copyir.com    Defective connector cable or poor contact in the connector      copyir.com PF thermistor 2 installed incorrectly      copyir.com Defective PF thermistor 2      copyir.com Broken PF heater 2      copyir.com Defective PF heater PWB or PF main PWB      copyir.com
1620    PF heater 1 low temperature error (paper feeder 2)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on      copyir.com    Defective connector cable or poor contact in the connector      copyir.com PF thermistor 1 installed incorrectly      copyir.com Defective PF thermistor 1      copyir.com Broken PF heater 1      copyir.com Defective PF heater PWB or PF main PWB      copyir.com
1630    PF heater 2 low temperature error (paper feeder 2)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on      copyir.com    Defective connector cable or poor contact in the connector      copyir.com PF thermistor 2 installed incorrectly      copyir.com Defective PF thermistor 2      copyir.com Broken PF heater 2      copyir.com Defective PF heater PWB or PF main PWB      copyir.com
1640    PF heater 1 low temperature error (paper feeder 3)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on      copyir.com    Defective connector cable or poor contact in the connector      copyir.com PF thermistor 1 installed incorrectly      copyir.com Defective PF thermistor 1      copyir.com Broken PF heater 1      copyir.com Defective PF heater PWB or PF main PWB      copyir.com
1650    PF heater 2 low temperature error (paper feeder 3)
An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on      copyir.com    Defective connector cable or poor contact in the connector      copyir.com PF thermistor 2 installed incorrectly      copyir.com Defective PF thermistor 2      copyir.com Broken PF heater 2      copyir.com Defective PF heater PWB or PF main PWB      copyir.com
1800    Paper feeder communication error
Communication error between engine PWB and optional paper feeder      copyir.com    Improper installation paper feeder      copyir.com Defective connector cable or poor contact in the connector      copyir.com Defective engine PWB      copyir.com Defective PF main PWB      copyir.com
2100    Developing motor error
The developing motor ready input is not given for 5 s during the main motor is ON      copyir.com?#`    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the developing motor      copyir.com Defective developing motor      copyir.com Defective engine PWB      copyir.com
2200    Drum motor error
The drum motor ready input is not given for 5 s during the drum motor is ON      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the drum motor      copyir.com Defective drum motor      copyir.com Defective engine PWB      copyir.com
2330    Fuser pressure release motor error
When the fuser pressure release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the fuser pressure release motor      copyir.com Defective fuser pressure release motor      copyir.com Defective engine PWB      copyir.com
2340    Fuser pressure release motor time-out error
When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6 s      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the fuser pressure release motor      copyir.com Defective fuser pressure release motor      copyir.com Defective engine PWB      copyir.com
2500    Paper feed motor error
The drum motor ready input is not given for 5 s during the paper feed motor is ON      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the paper feed motor      copyir.com Defective paper feed motor      copyir.com Defective engine PWB      copyir.com
2600    PF paper feed motor error (paper feeder 1)
The drum motor ready input is not given for 2 s during the PF paper feed motor is ON      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the PF paper feed motor      copyir.com Defective PF paper feed motor      copyir.com Defective PF main PWB      copyir.com
2610    PF paper feed motor error (paper feeder 2)
The drum motor ready input is not given for 2 s during the PF paper feed motor is ON      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the PF paper feed motor      copyir.com Defective PF paper feed motor      copyir.com Defective PF main PWB      copyir.com
2620    PF paper feed motor error (paper feeder 3)
The drum motor ready input is not given for 2 s during the PF paper feed motor is ON      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the PF paper feed motor      copyir.com Defective PF paper feed motor      copyir.com Defective PF main PWB      copyir.com
2730    Developing release motor error
When the developing release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the developing release motor      copyir.com Defective developing release motor      copyir.com Defective engine PWB      copyir.com
2740    Developing release motor time-out error
When the developing release motor is driven, the developing release switch (DEVRSW) is not detectable for 1 s      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the developing release motor      copyir.com Defective developing release motor      copyir.com Defective engine PWB      copyir.com
2820    Fuser motor error
The fuser motor ready input is not given for 5 s during the fuser motor is ON      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the fuser motor      copyir.com Defective fuser motor      copyir.com Defective engine PWB      copyir.com
4001    Polygon motor KM error
The polygon motor KM ready input is not given for 10 s during the polygon motor is ON      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective polygon motor KM      copyir.com Defective engine PWB      copyir.com
4002    Polygon motor CY error
The polygon motor CY ready input is not given for 10 s during the polygon motor is ON      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective polygon motor CY      copyir.com Defective engine PWB      copyir.com
4201    Laser output error (black)
The pin photo signal is not output from PD PWB K for one second while laser is emitted      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective APC PWB K      copyir.com Defective PD PWB K      copyir.com Defective engine PWB      copyir.com
4202    Laser output error (cyan)
The pin photo signal is not output from PD PWB C for one second while laser is emitted      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective APC PWB C      copyir.com Defective PD PWB C      copyir.com Defective engine PWB      copyir.com
4203    Laser output error (magenta)
The pin photo signal is not output from PD PWB M for one second while laser is emitted      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective APC PWB M      copyir.com Defective PD PWB M      copyir.com Defective engine PWB      copyir.com
4204    Laser output error (yellow)
The pin photo signal is not output from PD PWB Y for one second while laser is emitted      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective APC PWB Y      copyir.com Defective PD PWB Y      copyir.com Defective engine PWB      copyir.com
4600    LSU cleaning motor error
When the LSU cleaning motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the LSU cleaning motor      copyir.com Defective LSU cleaning motor      copyir.com Defective engine PWB      copyir.com
4700    VIDEO ASIC device error    Defective connector cable or poor contact in the connector      copyir.com Defective main PWB or engine PWB      copyir.com
5301    Broken cleaning lamp K wire
When the cleaning lamp K is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective cleaning lamp K      copyir.com Defective engine PWB      copyir.com
5302    Broken cleaning lamp C wire
When the cleaning lamp C is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective cleaning lamp C      copyir.com Defective engine PWB      copyir.com
5303    Broken cleaning lamp M wire
When the cleaning lamp M is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective cleaning lamp M      copyir.com Defective engine PWB      copyir.com
5304    Broken cleaning lamp Y wire
When the cleaning lamp Y is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective cleaning lamp Y      copyir.com Defective engine PWB      copyir.com
6000    Broken fuser heater wire
The detected temperature of fuser thermistor does not rise 1„aC/1      copyir.com8„aF after the fuser heater has been turned on continuously for 10 s in warming up      copyir.com The fuser temperature does not reach 100„aC/212„aF after the fuser heater has been turned on continuously for 30 s in warming up      copyir.com The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up      copyir.com The detected temperature of fuser thermistor does not rise 1„aC/1      copyir.com8„aF after the fuser heater has been turned on continuously for 10 s during printing      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Deformed connector pin      copyir.com Defective triac      copyir.com Fuser thermostat triggered      copyir.com Broken fuser heater wire      copyir.com Defective engine PWB      copyir.com
6020    Abnormally high fuser thermistor temperature
The fuser thermistor detects a temperature higher than 240C/464F      copyir.com By the activation of the high temperature error detection circuit (230„aC/446„aF or more) of fuser thermistor, the illumination of fuser heater was forcibly turned off and 10 s has elapsed      copyir.com    Deformed connector pin      copyir.com Defective triac      copyir.com Shorted fuser thermistor      copyir.com Defective engine PWB      copyir.com
6030    Broken fuser thermistor wire
Input from fuser thermistor is 3 or less (A/D value) continuously for 1 s      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Deformed connector pin      copyir.com Defective triac      copyir.com Broken fuser thermistor wire      copyir.com Fuser thermostat triggered      copyir.com Broken fuser heater wire      copyir.com Defective engine PWB      copyir.com
6400    Zero-cross signal error
The zero-cross signal does not reach the engine PWB for more than 1 s      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective power source PWB or engine PWB      copyir.com
7001    Toner motor K error
When the toner motor K is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the toner motor K      copyir.com Defective toner motor K      copyir.com Defective engine PWB      copyir.com
7002    Toner motor C error
When the toner motor C is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the toner motor C      copyir.com Defective toner motor C      copyir.com Defective engine PWB      copyir.com
7003    Toner motor M error
When the toner motor M is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the toner motor M      copyir.com Defective toner motor M      copyir.com Defective engine PWB      copyir.com
7004    Toner motor Y error
When the toner motor Y is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective drive transmission system of the toner motor Y      copyir.com Defective toner motor Y      copyir.com Defective engine PWB      copyir.com
7401    Developing unit K noninstalling error
No density detection signal is output from toner sensor K in developing unit K      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective toner sensor K      copyir.com Defective engine PWB      copyir.com
7402    Developing unit C noninstalling error
No density detection signal is output from toner sensor C in developing unit C      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective toner sensor C      copyir.com Defective engine PWB      copyir.com
7403    Developing unit M noninstalling error
No density detection signal is output from toner sensor M in developing unit M      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective toner sensor M      copyir.com Defective engine PWB      copyir.com
7404    Developing unit Y noninstalling error
No density detection signal is output from toner sensor Y in developing unit Y      copyir.com    Defective connector cable or poor contact in the connector      copyir.com Defective toner sensor Y      copyir.com Defective engine PWB      copyir.com
7411    Drum unit K non- installing error
The EEPROM of drum PWB K does not communicate normally      copyir.com    Installation of incompatible drum unit K      copyir.com Defective connector cable or poor contact in the connector      copyir.com Defective drum PWB K      copyir.com Defective engine PWB      copyir.com
7412    Drum unit C non- installing error
The EEPROM of drum PWB C does not communicate normally      copyir.com    Installation of incompatible drum unit C      copyir.com Defective connector cable or poor contact in the connector      copyir.com Defective drum PWB C      copyir.com Defective engine PWB      copyir.com
7413    Drum unit M non- installing error
The EEPROM of drum PWB M does not communicate normally      copyir.com    Installation of incompatible drum unit M      copyir.com Defective connector cable or poor contact in the connector      copyir.com Defective drum PWB M      copyir.com Defective engine PWB      copyir.com
7414    Drum unit Y non- installing error
The EEPROM of drum PWB Y does not communicate normally      copyir.com    Installation of incompatible drum unit Y      copyir.com Defective connector cable or poor contact in the connector      copyir.com Defective drum PWB Y      copyir.com Defective engine PWB      copyir.com
9530    Backup data error
The serial number of the machine written on the EEPROM of the engine PWB differs with that is written on both the flash memory of the engine PWB and the EEPROM of the drum PWB as a backup      copyir.com    Replacing both the engine PWB and the drum unit at the same time      copyir.com
F000    Main PWB – operation panel PWB communication error    Defective main PWB      copyir.com Defective operation panel PWB      copyir.com
F010    Main PWB checksum error    Defective main PWB      copyir.com
F020    Main PWB RAM checksum error    Defective main memory (RAM) on the main PWB      copyir.com Defective expanded memory (DIMM)      copyir.com
F040    Main PWB – print engine communication error    Defective main PWB      copyir.com Defective engine PWB      copyir.com
F050    Print engine ROM checksum error    Defective engine PWB      copyir.com
F278    Power supply in drive system error    Main power switch was turned off without using the power key, or a power failure has occurred      copyir.com

پست های مرتبط

دیدگاهتان را بنویسید

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

جستجو در مطالب

سوالی دارید؟

برای آگاهی از راه های ارتباط با ما، بر روی دکمه زیر کلیک کنید

مطالب جدید ...

در خبرنامه ما عضو شوید