لمینت MKP
1402-06-04
Menu
C0030 Fax control PWB system problem (optional fax) Processing with the fax software was disabled due to a hardware or software problem copyir.com Defective fax control PWB copyir.com
C0070 Abnormal detection of fax control PWB incompatibility (optional fax) In the initial communication with the fax control PWB, any normal communication command is not transmitted copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0100 Main PWB backup memory device problem Writing or erasing has not completed even after a certain time copyir.com Defective main PWB copyir.com
C0110 Backup memory data problem Data in the specified area of the backup memory does not match the specified values copyir.com Problem with the backup memory data copyir.com
C0150 Backup memory device problem (Engine PWB) An error occurs in backup data read or write for the engine PWB copyir.com An error occurs in control area deletion copyir.com Defective engine PWB copyir.com Data damage of EEPROM copyir.com
C0160 Backup memory data problem (Engine PWB) Data for backup data check is changed at the check after startup copyir.com Problem with the backup memory data copyir.com
C0170 Copy counts problem A checksum error is detected in the main and sub backup memories for the copy counters copyir.com Data damage of EEPROM copyir.comDefective main PWB copyir.com
C0180 Backup memory data problem Backup data on the main PWB has broken copyir.com Data damage of EEPROM copyir.com
C0210 CPU communication problem There is no reply after 3 retries at communication copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0220 Communication problem between the scanner PWB and main PWB There is no reply after 6 retries at communication copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0240 Printer PWB communication problem The printer PWB does not respond 120 s after the power is turned on copyir.com Poor contact in the connector terminals copyir.com DIMM or DDR installed incorrectly copyir.com Defective PWB copyir.com
C0250 Network scanner PWB communication problemThe response to the alive command to the network scanner transmitted once to 30 s does not come on the contrary three consecutive times or more copyir.com The response to the communication command transmitted to the network scanner does not return 75 s or more copyir.com (This code indicates only scanner function display copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0280 Communication problem between the fax control PWB and main PWB After main PWB status change signal turns on 1 minute, when it does not receive key required command from the fax control PWB, one time it resets the FAX copyir.comAfter that, while main PWB status change signal turns on furthermore 1 minute, when it does not receive key required command from the fax control PWB copyir.com When FAX_READY signal continues fake for 6 s, one time it resets the FAX copyir.com After that, when FAX_READY fake continues fake for 6 s copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0410 DP communication problem (optional DP) There is no reply after 10 retries at communication or a communication error occurs copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0420 Paper feeder communication error (optional paper feeder) A communication error from paper feeder is detected 10 times in succession copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0440 Document finisher communication problem (optional document finisher) A communication error from document finisher is detected 10 times in succession copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0610 Bitmap problem The DIMM on the main PWB does not operate correctly copyir.com Defective main PWB copyir.com DDR on the main PWB installed incorrectly copyir.com
C0630 DMA problem DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time copyir.com Defective main PWB copyir.com DDR on the main PWB installed incorrectly copyir.com
C0640 Hard disk drive problem The hard disk cannot be accessed copyir.com Poor contact in the connector terminals copyir.com Defective hard disk copyir.com Defective main PWB copyir.com
C0820 Fax control PWB CG ROM checksum error (optional fax) A checksum error occurred with the CG ROM data of the fax control PWB copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0830 Fax control PWB flash program area checksum error (optional fax) A checksum error occurred with the program of the fax control PWB copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0840 Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com Defective main PWB copyir.com The battery is disconnected from the main PWB copyir.com
C0860 Fax control PWB software switch checksum error (optional fax) A checksum error occurred with the software switch value of the fax control PWB copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0870 Fax control PWB to main PWB high capacity data transfer problem High-capacity data transfer between the fax control PWB and the scanner MIP PWB was not normally performed even if the data transfer was retried 10 times copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C0880 Program archive problem (optional fax) When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0890 Fax control PWB CG FONT archive problem (optional fax) When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed copyir.com Defective fax software copyir.com Defective fax control PWB copyir.com
C0920 Fax file system error The backup data is not retained for file system abnormality of flash memory of the fax control PWB copyir.com Defective fax control PWB copyir.com
C1010 Lift motor 1 error When cassette 1 is inserted, lift limit switch 1 does not turn on within 12 s of lift motor 1 turning on copyir.com Poor contact in the connector terminals copyir.com Broken gears or couplings of lift motor 1 copyir.com Defective lift motor 1 copyir.com Defective lift switch 1 copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C1020 Lift motor 2 error When cassette 2 is inserted, lift limit switch 2 does not turn on within 12 s of lift motor 2 turning on copyir.com Poor contact in the connector terminals copyir.com Broken gears or couplings of lift motor 2 copyir.com Defective lift motor 2 copyir.com Defective lift switch 2 copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C1030 Paper feeder lift motor 1 error (optional paper feeder) When optional cassette 3 is inserted, paper feeder lift switch 1 does not turn on within 12 s of paper feeder lift motor 1 turning on copyir.com The lift overcurrent protective monitor signal is detected above 500 ms during driving the motor copyir.com However, the first 1 s after paper feeder lift motor 1 is turned on is excluded from detection copyir.com Poor contact in the connector terminals copyir.com Broken gears or couplings of paper feeder lift motor 1 copyir.com Defective paper feeder lift motor 1 copyir.com Defective paper feeder lift switch 1 copyir.com
C1040 Paper feeder lift motor 2 error (optional paper feeder) When optional cassette 4 is inserted, paper feeder lift switch 2 does not turn on within 12 s of paper feeder lift motor 2 turning on copyir.com The lift overcurrent protective monitor signal is detected above 500 ms during driving the motor copyir.com However, the first 1 s after paper feeder lift motor 2 is turned on is excluded from detection copyir.com Poor contact in the connector terminals copyir.com Broken gears or couplings of paper feeder lift motor 2 copyir.com Defective paper feeder lift motor 2 copyir.com Defective paper feeder lift switch 2 copyir.com
C1100 Paper feeder lift motor 1 error (optional 3000-sheet paper feeder) A motor over-current signal is detected continuously for 1 s or longer copyir.com Poor contact in the connector terminals copyir.com Paper feeder lift motor 1 does not rotate correctly (the motor is overloaded) copyir.com
C1110 Paper feeder lift motor 2 error (optional 3000-sheet paper feeder) A motor over-current signal is detected continuously for 1 s or longer copyir.com Poor contact in the connector terminals copyir.com Paper feeder lift motor 2 does not rotate correctly (the motor is overloaded) copyir.com
C1120 Paper feeder left lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 1 does not turn on within 30 s of paper feeder lift motor 2 turning on copyir.com Poor contact in the connector terminals copyir.com Defective paper feeder lift switch 1 copyir.com Defective paper feeder lift motor 2 copyir.com The paper feeder left lift does not rise properly copyir.com
C1130 Paper feeder right lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 2 does not turn on within 30 s of paper feeder lift motor 1 turning on copyir.com Poor contact in the connector terminals copyir.com Defective paper feeder lift switch 2 copyir.com Defective paper feeder lift motor 1 copyir.com The paper feeder right lift does not rise properly copyir.com
C1900 Paper feeder EEPROM error (optional paper feeder) When writing the data, the write data and the read data is not continuously in agreement three times copyir.com Poor contact in the connector terminals copyir.com Defective engine PWB copyir.com Defective paper feeder copyir.com
C1950 Transfer belt unit EEPROM error Read and write data does not match copyir.com Poor contact in the connector terminals copyir.com Defective transfer belt speed detection PWB (inner transfer belt unit) copyir.com
C2101 Paper feed/developing motor BK error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective engine PWB copyir.com Defective paper feed/developing motor BK copyir.com
C2102 Developing motor CMY error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective engine PWB copyir.com Defective developing motor CMY copyir.com
C2201 Drum motor BK error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drum motor BK copyir.com Defective PWB copyir.com
C2202 Drum motor C error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drum motor C copyir.com Defective PWB copyir.com
C2203 Drum motor M error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drum motor M copyir.com Defective PWB copyir.com
C2204 Drum motor Y error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drum motor Y copyir.com Defective PWB copyir.com
C2300 Fuser motor error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective engine PWB copyir.com Defective fuser motor copyir.com
C2400 Eject motor error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective engine PWB copyir.com Defective eject motor copyir.com
C2500 MP motor error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective engine PWB copyir.com Defective MP motor copyir.com
C2600 Paper feeder paper conveying motor error (optional paper feeder) The lock signal of the motor is detected above 450 ms copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective PWB copyir.com Defective paper feeder paper conveying motor copyir.com
C2810 Waste toner motor error The rated speed achievement signal won’t turn to L in 5 s since the motor is activated copyir.com The rated speed achievement signal turns to H every other 5 s after the machine is stabilized copyir.com Poor contact in the connector terminals copyir.com Defective drive transmission system copyir.com Defective waste toner motor copyir.com Defective engine PWB copyir.com
C3100 Scanner carriage problem The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Defective scanner PWB copyir.com Defective scanner home position switch copyir.com Defective scanner motor copyir.com Poor contact in the connector terminals copyir.com The mirror frame, exposure lamp, or scanner wire is defective copyir.com
C3200 Exposure lamp problem The exposure lamp is not turned on when starting the copy copyir.com Poor contact in the connector terminals copyir.com Defective scanner PWB copyir.com Defective CCD PWB copyir.com Defective exposure lamp or inverter PWB copyir.com Incorrect shading position copyir.com
C3300 Optical system (AGC) problem After AGC, correct input is not obtained at CCD copyir.com Poor contact in the connector terminals copyir.com Defective exposure lamp copyir.com Defective PWB copyir.com
C3500 Communication error between scanner and SHD An error code is detected copyir.com Poor contact in the connector terminals copyir.com Defective PWB
C3900 Backup memory read/write problem (scanner PWB) Read and write data does not match copyir.com Defective backup RAM or scanner PWB copyir.com
C3910 Backup memory data problem (scanner PWB) Data in the specified area of the backup memory does not match the specified values copyir.com Problem with the backup memory data copyir.com Defective scanner PWB copyir.com
C4000 Polygon motor synchronization problem The rated speed achievement signal won’t turn to L in 20 s since the polygon motor is activated copyir.com Poor contact in the connector terminals copyir.com Defective polygon motor copyir.com Defective engine PWB copyir.com
C4010 Polygon motor steady-state problem The rated speed achievement signal turns to H every other 5 s after the polygon motor is stabilized copyir.com Poor contact in the connector terminals copyir.com Defective polygon motor copyir.com Defective engine PWB copyir.com
C4100 BD initialization problem When power is turned on, ASIC of engine PWB detects a BD error for 200 ms copyir.com Poor contact in the connector terminals copyir.com Defective APC PWB BK (inner laser scanner unit) Defective engine PWB copyir.com
C4200 BD steady-state problem ASIC of the engine PWB detects a BD error for 200 ms after the polygon motor rotation has been stabilized copyir.com Poor contact in the connector terminals copyir.com Defective laser scanner unit copyir.com Defective engine PWB copyir.com
C5101 Main high-voltage BK error Abnormality of charger roller BK is detected when Vpp adjustment copyir.com Installation defectiveness on charger roller unit BK copyir.com Defective charger roller unit BK copyir.com
C5102 Main high-voltage C error Abnormality of charger roller C is detected when Vpp adjustment copyir.com Installation defectiveness on charger roller unit C copyir.com Defective charger roller unit C copyir.com
C5103 Main high-voltage M error Abnormality of charger roller M is detected when Vpp adjustment copyir.com Installation defectiveness on charger roller unit M copyir.com Defective charger roller unit M copyir.com
C5104 Main high-voltage Y error Abnormality of charger roller Y is detected when Vpp adjustment copyir.com Installation defectiveness on charger roller unit Y copyir.com Defective charger roller unit Y copyir.com
C5301 Cleaning lamp BK break error After the cleaning lamp BK ON signal is turned on, the cleaning lamp BK break signal is detected continuously 5 times for 10 ms copyir.com Poor contact in the connector terminals copyir.com Defective cleaning lamp BK copyir.com Defective engine PWB copyir.com
C5302 Cleaning lamp C break error After the cleaning lamp C ON signal is turned on, the cleaning lamp C break signal is detected continuously 5 times for 10 ms copyir.com Poor contact in the connector terminals copyir.com Defective cleaning lamp C copyir.com Defective engine PWB copyir.com
C5303 Cleaning lamp M break error After the cleaning lamp M ON signal is turned on, the cleaning lamp M break signal is detected continuously 5 times for 10 ms copyir.com Poor contact in the connector terminals copyir.com Defective cleaning lamp M copyir.com Defective engine PWB copyir.com
C5304 Cleaning lamp Y break error After the cleaning lamp Y ON signal is turned on, the cleaning lamp Y break signal is detected continuously 5 times for 10 ms copyir.com Poor contact in the connector terminals copyir.com Defective cleaning lamp Y copyir.com Defective engine PWB copyir.com
C6000 Fuser thermistor 1/3 break error Fuser thermistor 1 detected 40 C/104 F or less during warming up copyir.com 40 C/104 F or less is detected between 10 s of continuation during worming up copyir.com Fuser thermistor 3 detected 40 C/104 F or less during warming up copyir.com Defective fuser heater 1/2 copyir.com Defective fuser thermostat 1 copyir.com Installation defectiveness on fuser thermistor 1/2 copyir.com Defective PWB copyir.com
C6010 Abnormally high fuser thermistor temperature The fuser Abnormally high signal is detected for 60 s or more copyir.com Defective PWB copyir.com
C6020 Abnormally high fuser thermistor 1/3 temperature The fuser temperature exceeds 240 C/ 464 F copyir.com Defective PWB copyir.com Installation defectiveness on fuser thermistor 1/3 copyir.com
C6030 Fuser thermistor 1/3 break error Fuser thermistor 1 detected 40 C/104 F or less during warming up copyir.com 40 C/104 F or less is detected between 10 s of continuation during worming up copyir.com Fuser thermistor 3 detected 40 C/104 F or less during warming up copyir.com Defective fuser heater 1/2 copyir.com Installation defectiveness on fuser thermistor 1/3 copyir.com Defective PWB copyir.com
C6050 Abnormally low fuser thermistor 3 temperature During copying, the temperature at the heat roller lower than 100 C/212 F is detected continuously for 1 s copyir.com Defective fuser heater 1/2 copyir.com Defective PWB copyir.com
C6100 Fuser heater 3 break Fuser thermistor 2 detected less than 100 C/212 F for 120 s during driving copyir.com Fuser thermistor 2 deduced less than 150 C/302 F for 300 s during driving copyir.com Fuser thermistor 2 deduced less than 100 C/212 F for 5 s during driving copyir.com Defective fuser heater 3 copyir.com Defective fuser thermostat 2 copyir.com Installation defectiveness on fuser thermistor 2 copyir.com Defective PWB copyir.com
C6120 Abnormally high fuser thermistor 2 temperature The fuser temperature exceeds 190 C/ 374 F copyir.com Installation defectiveness on fuser thermistor 2 copyir.com Defective PWB copyir.com
C6130 Fuser thermistor 2 break error Fuser thermistor 2 detected less than 40 C/104 F during driving copyir.com When the difference of temperature of fuser thermistor 1 and 3 becomes 100 C/212 F or more copyir.com Installation defectiveness on fuser thermistor 2 copyir.com Defective fuser heater 3 copyir.com Defective PWB copyir.com
C6400 Zero-cross signal error While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 3 s copyir.com Defective PWB copyir.com
C7000 Toner motor problem The rated speed achievement signal won’t turn to L in 5 s since the motor is activated copyir.com The rated speed achievement signal turns to H every other 5 s after the machine is stabilized copyir.com Poor contact in the connector terminals copyir.com Broken the gear copyir.com Defective toner motor M/C/Y/BK copyir.com Defective engine PWB copyir.com
C7101 Toner sensor BK problem Sensor output value of 78 or less or 944 or more continued for 3 s copyir.com Defective developing unit BK copyir.com Defective engine PWB copyir.com
C7102 Toner sensor C problem Sensor output value of 78 or less or 944 or more continued for 3 s copyir.com Defective developing unit C copyir.com Defective engine PWB copyir.com
C7103 Toner sensor M problem Sensor output value of 78 or less or 944 or more continued for 3 s copyir.com Defective developing unit M copyir.com Defective engine PWB copyir.com
C7104 Toner sensor Y problem Sensor output value of 78 or less or 944 or more continued for 3 s copyir.com Defective developing unit Y copyir.com Defective engine PWB copyir.com
C7200 Broken internal thermistor wire An abnormal value is detected in the input data to inner temperature sensor 1 copyir.com Poor contact in the connector terminals copyir.com Defective laser scanner unit copyir.com Defective engine PWB copyir.com
C7210 Short-circuited internal thermistor An abnormal value is detected in the input data to inner temperature sensor 1 copyir.com Poor contact in the connector terminals copyir.com Defective laser scanner unit copyir.com Defective engine PWB copyir.com
C7220 Broken internal thermistor 2 wire An abnormal value is detected in the input data to inner temperature sensor 2 copyir.com Poor contact in the connector terminals copyir.com Defective engine PWB copyir.com
C7230 Short-circuited internal thermistor 2 An abnormal value is detected in the input data to inner temperature sensor 2 copyir.com Poor contact in the connector terminals copyir.com Defective engine PWB copyir.com
C7240 Broken internal thermistor 3 wire An abnormal value is detected in the input data to inner temperature sensor 3 copyir.com Poor contact in the connector terminals copyir.com Defective engine PWB copyir.com
C7250 Short-circuited internal thermistor 3 An abnormal value is detected in the input data to inner temperature sensor 3 copyir.com Poor contact in the connector terminals copyir.com Defective engine PWB copyir.com
C7401 Developing unit BK type mismatch problem Absence of the developing unit BK is detected copyir.com Developing unit connector inserted incorrectly copyir.com Different type of the developing unit is installed copyir.com
C7402 Developing unit C type mismatch problem Absence of the developing unit C is detected copyir.com Developing unit connector inserted incorrectly copyir.com Different type of the developing unit is installed copyir.com
C7403 Developing unit M type mismatch problem Absence of the developing unit M is detected copyir.com Developing unit connector inserted incorrectly copyir.com Different type of the developing unit is installed copyir.com
C7404 Developing unit Y type mismatch problem Absence of the developing unit Y is detected copyir.com Developing unit connector inserted incorrectly copyir.com Different type of the developing unit is installed copyir.com
C7411 Drum unit BK type mismatch problem Absence of the drum unit BK is detected copyir.com Drum unit connector inserted incorrectly copyir.com Different type of the drum unit is installed copyir.com
C7412 Drum unit C type mismatch problem Absence of the drum unit C is detected copyir.com Drum unit connector inserted incorrectly copyir.com Different type of the drum unit is installed copyir.com
C7413 Drum unit M type mismatch problem Absence of the drum unit M is detected copyir.com Drum unit connector inserted incorrectly copyir.com Different type of the drum unit is installed copyir.com
C7414 Drum unit Y type mismatch problem Absence of the drum unit Y is detected copyir.com Drum unit connector inserted incorrectly copyir.com Different type of the drum unit is installed copyir.com
C7420 Transfer belt unit type mismatch problem Absence of the transfer belt unit is detected copyir.com Transfer belt unit connector inserted incorrectly copyir.com Different type of the transfer belt unit is installed copyir.com
C7800 Broken external thermistor wire An abnormal value is detected in the input data to the outer temperature sensor copyir.com Poor contact in the connector terminals copyir.com Defective engine PWB copyir.com
C7810 Short-circuited external thermistor An abnormal value is detected in the input data to the outer temperature sensor copyir.com Poor contact in the connector terminals copyir.com Defective engine PWB copyir.com
C7901 Drum BK EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective drum PWB BK copyir.com
C7902 Drum C EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective drum PWB C copyir.com
C7903 Drum M EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective drum PWB M copyir.com
C7904 Drum Y EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective drum PWB Y copyir.com
C7911 Developing unit BK EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective developing PWB BK copyir.com
C7912 Developing unit C EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective developing PWB C copyir.com
C7913 Developing unit M EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective developing PWB M copyir.com
C7914 Developing unit Y EEPROM error Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com Defective developing PWB Y copyir.com
C8020 Punch motor problem (optional 3000 sheet document finisher) The LOCK signal of the punch motor is detected for more than 500 ms while the punch motor is operating copyir.com Poor contact in the connector terminals copyir.com Defective punch motor copyir.com Defective PWB copyir.com
C8030 Tray upper limit detection problem (optional document finisher) When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected copyir.com The tray upper limit sensor/push paper sensor/surface view sensor connector makes poor contact copyir.com Defective tray upper limit sensor/ push paper sensor/ surface view sensor copyir.com Defective finisher main PWB copyir.com
C8050 Paper conveying belt motor 1 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 1 does not turn off within 1 copyir.com5 s copyir.com Paper conveying belt home position sensor 1 does not turn on within 2 copyir.com5 s copyir.com Jam 88 is indicated copyir.com Poor contact in the connector terminals copyir.com Defective paper conveying belt home position sensor 1 copyir.com Defective paper conveying belt motor 1 copyir.com Defective PWB copyir.com
C8060 Paper conveying belt motor 2 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 2 does not turn off within 1 copyir.com5 s copyir.com Paper conveying belt home position sensor 2 does not turn on within 1 copyir.com5 s copyir.com Poor contact in the connector terminals copyir.com Defective paper conveying belt home position sensor 2 copyir.com Defective paper conveying belt motor 2 copyir.com Defective PWB copyir.com
C8070 Internal tray communication error (optional 3000-sheet document finisher) Communication with the internal tray is not possible although the connection is detected copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C8140 Main tray problem (optional 3000- sheet document finisher) The main tray is not detected by the main tray upper limit detection sensor or the main tray paper upper surface detection sensor within 20s since the tray has started ascending copyir.com The main tray upper limit detection sensor or the main tray paper upper surface detection sensor is not detected to be turned off in 20 s after the main tray has descended copyir.com The main tray low limit detection sensor is not detected to be turned on in 20 s after the main tray has descended copyir.com During main tray ascent, the main tray upper limit detection sensor or the main tray paper upper surface detection sensor stays on for more than 2 s copyir.com Poor contact in the connector terminals Defective main tray motor copyir.comDefective main tray upper limit detection sensor/main tray paper upper surface detection sensor/main tray lower limit detection sensor copyir.com Defective finisher main PWB copyir.com
C8140 Tray elevation motor problem (optional document finisher) The tray low limit sensor, paper retaining sensor or paper surface sensor cannot be detected to be on within 10 s since the tray elevation motor is activated copyir.com The tray elevation motor connector makes poor contact copyir.com The tray elevation motor malfunctions copyir.com The tray lower limit sensor/push paper sensor/surface view sensor connector makes poor contact copyir.com Defective tray lower limit sensor/ push paper sensor/ surface view sensor copyir.com Defective finisher main PWB copyir.com
C8170 Side registration motor 1 problem (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 s passed copyir.com Jam 88 is indicated copyir.com Poor contact in the connector terminals copyir.com Defective side registration motor 1 copyir.com Defective PWB copyir.com
C8170 Adjustment motor problem (optional document finisher) The registration home position sensor cannot be detected to be on or off within 125 ms since the registration motor is activated after registration has started copyir.com The registration home position sensor cannot be detected to be on within 710 ms since the registration motor is activated after registration has ceased copyir.com The adjustment motor connector makes poor contact Defective adjustment motor copyir.com The adjustment home position sensor connector makes poor contact copyir.com Defective adjustment home position sensor copyir.com Defective finisher main PWB copyir.com
C8180 Side registration motor 2 problem (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 s passed copyir.com Jam 88 is indicated copyir.com Poor contact in the connector terminals copyir.com Defective side registration motor 2 copyir.com Defective PWB copyir.com
C8210 Stapler shift motor 1 error (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 1 copyir.com5 s passed copyir.com Poor contact in the connector terminals copyir.com Defective stapler shift motor 1 copyir.com Defective finisher main PWB copyir.com
C8210 Stapler problem (optional document finisher) When the stapler motor is driving, the ON status of the stapler home position sensor cannot be detected even if 1 s passed copyir.com The stapler connector makes poor contact copyir.com The stapler is blocked with a staple copyir.com The stapler is broken copyir.com Defective finisher main PWB copyir.com
C8220 Stapler shift motor 2 error (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 copyir.com5 s passed copyir.com Poor contact in the connector terminals copyir.com Defective stapler shift motor 2 copyir.com Defective finisher main PWB copyir.com
C8230 Stapler motor problem (optional 3000sheet document finisher) Jam 82 is indicated copyir.com Poor contact in the connector terminals copyir.com Defective stapler motor copyir.com Defective finisher main PWB copyir.com
C8300 Centerfold unit communication error (optional centerfold unit of 3000-sheet document finisher) Communication with the centerfold unit is not possible although the connection is detected copyir.com Poor contact in the connector terminals copyir.com Defective centerfold set switch copyir.com Defective finisher main PWB copyir.com
C8310 Centerfold side registration motor 1 problem (optional centerfold unit of 3000-sheet document finisher) The home position is not detected when initial operation even if 1 s passed copyir.com Poor contact in the connector terminals copyir.com Defective centerfold side registration motor 1 copyir.com Defective PWB copyir.com
C8320 Centerfold paper conveying belt motor problem (optional centerfold unit of 3000-sheet document finisher) The home position is not detected when initial operation even if 2 copyir.com5 s passed copyir.com Poor contact in the connector terminals copyir.com Defective centerfold paper conveying belt motor 1/2 copyir.com Defective PWB copyir.com
C8330 Blade motor problem (optional centerfold unit of 3000-sheet document finisher) The home position is not detected when initial operation even if 1 copyir.com5 s passed copyir.com Poor contact in the connector terminals copyir.com Defective blade motor copyir.com Defective PWB copyir.com
C8340 Centerfold staple motor problem (optional centerfold unit of 3000-sheet document finisher) Jam89 is indicated copyir.com Poor contact in the connector terminals copyir.com Defective centerfold staple motor copyir.com Defective PWB copyir.com
C8350 Centerfold side registration motor 2 problem (optional centerfold unit of 3000-sheet document finisher) The home position is not detected when initial operation even if 1 s passed copyir.com Poor contact in the connector terminals copyir.com Defective centerfold side registration motor 2 copyir.com Defective PWB copyir.com
C8360 Centerfold main motor problem (optional centerfold unit of 3000-sheet document finisher) The motor lock signal is detected above 1 s during driving the centerfold main motor copyir.com Poor contact in the connector terminals copyir.com Defective centerfold main motor copyir.com Defective PWB copyir.com
C8440 Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range copyir.com The paper entry sensor connector makes poor contact copyir.com Defective paper entry sensor copyir.com The optical path of the paper entry sensor is blocked by foreign matter copyir.com Defective finisher main PWB copyir.com
C8460 EEPROM problem (optional document finisher) Read and write data does not match 3 times in succession copyir.com Defective EEPROM or finisher main PWB copyir.com
C8500 Mailbox communication error (optional mailbox of 3000-sheet document finisher) Communication with the mailbox is not possible although the connection is detected copyir.com Poor contact in the connector terminals copyir.com Defective PWB copyir.com
C8510 Mailbox drive motor problem (optional mailbox of 3000-sheet document finisher) The motor lock signal is detected above 500 ms during driving the mailbox drive motor copyir.com Poor contact in the connector terminals copyir.com Defective mailbox drive motor copyir.com Defective PWB copyir.com
C8900 Backup memory data problem (optional 3000-sheet document finisher) Read and write data does not match 3 times in succession copyir.com Poor contact in the connector terminals copyir.com Defective finisher main PWB copyir.com
C8910 Backup memory data problem (optional 3000-sheet document finisher) Read and write data does not match 3 times in succession copyir.com Poor contact in the connector terminals copyir.com Defective punch PWB copyir.com
C8920 Backup memory data problem (optional mailbox of 3000-sheet document finisher) Read and write data does not match 3 times in succession copyir.com Poor contact in the connector terminals copyir.com Defective mailbox main PWB copyir.com
C8930 Backup memory data problem (optional centerfold unit of 3000-sheet document finisher) Read and write data does not match 3 times in succession copyir.com Poor contact in the connector terminals copyir.com Defective centerfold main PWB copyir.com
C9060 EEPROM problem (optional DP) Read and write data does not match copyir.com Poor contact in the connector terminals copyir.com Defective DP drive PWB copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.