فروشگاه ماشین‌های اداری کپی ایران - کیو سرا میتا km4220
(0) محصول
یکشنبه, 12 ارديبهشت 1395 ساعت 14:36

کیو سرا میتا km4220

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

C001    Memory copy PCB 1 communication problem • Problems with data from memory copy PCB 1       copyir.com    Defective memory copy PCB 1       copyir.com
C003    Memory copy PCB 2 problem* 1 • Problems with data from memory copy PCB 2       copyir.com    Defective memory copy PCB 2       copyir.com
C010    RAM/ROM problem • Read and write data does not match       copyir.com    Defective main PCB       copyir.com
C011    Backup memory data problem • Data in the specified area of the backup memory does not match the specified values       copyir.com    Problem with the backup memory data       copyir.com Defective backup RAM       copyir.com
C021    Operation unit main PCB communication problem • There is no reply after 20 retries at communication       copyir.com    Poor contact of the connector terminals       copyir.com Defective main PCB or operation unit main PCB       copyir.com
C022    Communication problem between the engine PCB and main PCB
• There is no reply after 20 retries at communication       copyir.com    Defective engine ROM IC       copyir.com Defective main PCB       copyir.com
C023    Scanner communication problem • There is no reply after 5 retries at communication       copyir.com    Defective main PCB       copyir.com
C024    Printer board communication problem*2 •There is no reply after 20 retries at communication       copyir.com    Poor contact of the connector terminals       copyir.com Defective main PCB or printer board       copyir.com
C026    Memory copy PCB 1 communication problem • There is no reply after five retries at transmitting       copyir.com • There is no reply after five retries at receiving       copyir.com    Poor contact of the connector terminals       copyir.com Defective main PCB or memory copy PCB 1       copyir.com
C032    Large paper deck communication problem 1 • Communication errors from the communication microcomputer (IC56) on the main PCB: No communication: there is no replay after 3 retries       copyir.com Abnormal communication: a communication error (parity or checksum error) is detected five times in succession       copyir.com    Poor contact of the connector terminals       copyir.com Defective engine PCB       copyir.com Defective main PCB       copyir.com Defective deck main PCB       copyir.com
C032    Paper feed desk communication problem 3 • An error code from the paper feed desk is detected eight times in succession       copyir.com No communication: there is no reply after 3 retries       copyir.com Abnormal communication: a communication error (parity or checksum error) is detected five times in succession       copyir.com    Poor contact of the connector
terminals       copyir.com Defective engine PCB       copyir.com
Defective main PCB       copyir.com Defective desk main PCB       copyir.com
C034    Finisher communication problem 2 • Communication errors from the communication microcomputer (IC56) on the main PCB: No communication: there is no reply after 3 retries       copyir.com Abnormal communication: a communication error (parity or checksum error) is detected five times in succession       copyir.com    Poor contact of the connector terminals       copyir.com Defective engine PCB       copyir.com Defective main PCB       copyir.com Defective finisher main PCB       copyir.com
C036    Memory copy PCB 2 communication problem 1 • There is no reply after five retries at transmitting       copyir.com • There is no reply after five retries at receiving       copyir.com    Poor contact of the connector terminals       copyir.com
C037    Communication microcomputer problem • A problem is detected with the communication microcomputer (IC56) on the main PCB       copyir.com    Defective main PCB or memory copy PCB 2       copyir.com Defective main PCB       copyir.com
C104    Optical system problem • After AGC, correct input is not obtained at CCD       copyir.com    Insufficient exposure lamp luminosity       copyir.com Defective mainPCB       copyir.com Incorrect shading position       copyir.com CCD PCB output problem       copyir.com
C200    Drive motor problem • DM LOCK signal remains high for 1 s, 1 s after the drive motor has turned on       copyir.com    Poor contact of the drive motor connector terminals       copyir.com Defective drive motor rotation control circuit       copyir.com Defective drive transmission system       copyir.com
C210    Paper conveying motor problem • PCM LOCK signal remains high for 1 s, 1 s after the conveying motor has turned on       copyir.com    Poor contact of the paper conveying motor connector terminals       copyir.com Defective paper conveying motor rotation control circuit       copyir.com Defective drive transmission system       copyir.com
C220    Side registration motor problem • A problem where the side registration home position switch does not turn off after the side registration motor has turned 30 steps or the switch does not turn on after the motor has turned 265 steps is detected twice in succession       copyir.com (The first time, the copier indicates that the duplex unit is not inserted correctly, requesting the user to open and reinsert the duplex unit       copyir.com After the second detection, the copier enters partial operation control       copyir.com)    Defective side registration motor       copyir.com Defective side registration home position switch       copyir.com Poor contact of the connector terminals       copyir.com Malfunction of the side registration guides       copyir.com
C230    Paper feed motor problem • PFM LOCK signal remains high for 1 s, 1 s after the paper feed motor has turned on       copyir.com    Poor contact of the connector terminals       copyir.com Defective paper feed motor rotation control circuit       copyir.com Defective drive transmission system       copyir.com
C231    Desk drive motor problem 3 • DDM LOCK signal remains high for 1 s, 2 s after the desk drive motor has turned on       copyir.com    Poor contact of the desk drive motor connector terminals       copyir.com Defective desk drive motor rotation control circuit       copyir.com
C241    Upper lift motor problem • When the drawer is inserted, the upper lift limit switch does not turn on within 4 to 5 s of the upper lift motor turning on       copyir.com • During copying, the upper lift limit switch does not turn on within 200 ms of the upper lift motor turning on       copyir.com    Broken gears or couplings of the upper lift motor       copyir.com Defective upper lift motor       copyir.com Poor contact of the upper lift motor connector terminals       copyir.com Defective upper lift limit switch       copyir.com Poor contact of the upper lift limit switch connector terminals       copyir.com
C242    Lower lift motor problem • When the drawer is inserted, the lower lift limit switch does not turn on within 4 to 5 s of the lower lift motor turning on       copyir.com • During copying, the lower lift limit switch does not turn on within 200 ms of the lower lift motor turning on       copyir.com    Broken gears or couplings of the lower lift motor Defective lower lift motor       copyir.com Poor contact of the lower lift motor connector terminals       copyir.com
C243    Upper desk lift motor problem 3 • When the drawer is inserted, the upper desk lift limit switch does not turn on within 4 to 5 s of the upper desk lift motor turning on       copyir.com • During copying, the upper desk lift limit switch does not turn on within 200 ms of the upper desk lift motor turning on       copyir.com    Broken gears or couplings of the upper desk lift motor       copyir.com Defective upper desk lift motor       copyir.com Poor contact of the upper desk lift motor connector terminals       copyir.com Defective upper desk lift limit switch       copyir.com Poor contact of the upper desk lift limit switch connector terminals
C244    Lower desk lift motor problem 3 • When the drawer is inserted, the lower desk lift limit switch does not turn on within 4 to 5 s of the lower desk lift motor turning on       copyir.com • During copying, the lower desk lift limit switch does not turn on within 200 ms of the lower desk lift motor turning on       copyir.com    Broken gears or couplings of the lower desk lift motor       copyir.com Defective lower desk lift motor       copyir.com Poor contact of the lower desk lift motor connector terminals       copyir.com Defective lower desk lift limit switch       copyir.com Poor contact of the lower desk lift limit switch connector terminals       copyir.com
C310    Scanner carriage problem • The home position is not correct when the power is turned on or at the start of copying using the bypass table       copyir.com    Poor contact of the connector terminals       copyir.com Defective scanner home position switch       copyir.com Defective main PCB or scanner motor PCB       copyir.com Defective scanner motor       copyir.com
C332    Scanner watchdog problem • The main routine does not run within 8       copyir.com192 ms of the main switch being turned on    Defective main PCB       copyir.com
C340    Original detection position problem • The original size detection microcomputer in the main PCB cannot store initial data correctly       copyir.com    Poor contact of the connectors       copyir.com Defective original size sensor       copyir.com Defective main PCB or scanner motor PCB       copyir.com
C400    Polygon motor synchronization problem • The polygon motor does not reach the stable speed within 9 s of the polygon motor remote signal turning on       copyir.com    Poor contact of the polygon motor connector terminals       copyir.com Defective polygon motor       copyir.com Defective power source PCB       copyir.com Defective engine PCB       copyir.com
C401    Polygon motor steadystate problem • The polygon motor rotation is not stable for 600 ms after the polygon motor rotation has been stabilized       copyir.com    Poor contact of the polygon motor connector terminals       copyir.com Defective polygon motor       copyir.com Defective power source PCB       copyir.com Defective engine PCB       copyir.com
C420    BD steady-state problem • The VTC detects a BD error for 600 ms after the polygon motor rotation has been stabilized       copyir.com    Defective laser diode       copyir.com Defective polygon motor       copyir.com Defective main PCB       copyir.com
C510    Main charger problem • MC ALM signal is detected continuously for 400 ms when MC REM signal is turned on       copyir.com    Defective highvoltage transformer PCB       copyir.com Leakage during main charging       copyir.com
C511    Transfer/separation highvoltage problem • STALM signal is detected continuously for 400 ms when TC/SC REM signal is turned on       copyir.com    Defective highvoltage transformer PCB       copyir.com Leakage during transfer/separation charging       copyir.com
C610    Broken fixing unit thermistor wire • The fixing temperature does not increase for 40 s after the fixing heaters have been turned on for warming up       copyir.com • The fixing temperature remains below 50C/122F for 10 s continuously after the fixing heaters have been turned on during stabilization       copyir.com    Poor contact of the fixing unit thermistor connector terminals       copyir.com Broken fixing unit thermistor wire       copyir.com Fixing unit thermistor installed incorrectly       copyir.com Fixing unit thermostat triggered       copyir.com Fixing unit heater M or S installed incorrectly       copyir.com Broken fixing unit heater M or S wire       copyir.com
C620    Abnormally low fixing temperature • The fixing temperature remains below 120C/248F for 10 s       copyir.com    Poor contact of the fixing unit thermistor connector terminals       copyir.com Broken fixing unit thermistor wire       copyir.com Fixing unit thermistor installed incorrectly       copyir.com Fixing unit thermostat triggered       copyir.com Fixing unit heater M or S installed incorrectly       copyir.com Broken fixing unit heater M or S wire       copyir.com
C630    Abnormally high fixing temperature • The fixing temperature exceeds 220C/428F for 10 s       copyir.com • The fixing unit high temperature detection circuit on the engine PCB detects an abnormally high temperature       copyir.com    Shorted fixing unit thermistor       copyir.com Broken fixing unit heater control circuit on the power source PCB       copyir.com
C640    Zero-crossing signal problem • The main PCB does not detect the zero-crossing signal (Z CROSS SIG) for the time specified below       copyir.com At power-on: 3 s Others: 5 s    Poor contact of the connector terminals       copyir.com Defective power source PCB       copyir.com Defective main PCB       copyir.com
C710    Toner sensor problem • The sensor output voltage is outside the range of 0       copyir.com5 to 4       copyir.com5 V during copying or in maintenance item U130       copyir.com • The toner sensor control voltage cannot be set within the range in maintenance item U130       copyir.com    Defective toner sensor       copyir.com Poor contact of the toner sensor connector terminals       copyir.com Developer problem       copyir.com
C730    Broken external temperature thermistor wire • The input voltage is above 4       copyir.com5 V (230 bits)       copyir.com    Poor contact of the humidity sensor PCB connector terminals       copyir.com Defective external temperature thermistor       copyir.com
C731    Short-circuited external temperature thermistor • The input voltage is below 0       copyir.com5 V (250 bits)       copyir.com    Poor contact of the humidity sensor PCB connector terminals       copyir.com Defective external temperature thermistor       copyir.com
C740    Toner hopper problem • The toner hopper lockup sensor does not turn off after the toner recycle motor has rotated for at least 1 minute       copyir.com    Toner main hopper lockup       copyir.com Defective toner hopper lockup sensor       copyir.com Poor contact of the toner hopper lockup sensor connector terminals       copyir.com Defective toner recycle motor       copyir.com Poor contact of the toner recycle motor connector terminals       copyir.com
C801    Finisher paper conveying motor problem 2 • The paper conveying motor lockup signal is detected for 0       copyir.com5 s or longer       copyir.com    The paper conveying motor connector makes poor contact       copyir.com The paper conveying motor malfunctions       copyir.com Defective finisher main PCB       copyir.com
C803    Finisher paper conveying belt problem 2 • An on-to-off or off-to-on state change of the paper conveying belt home position sensor is not detected within 2 s of the paper conveying belt clutch turning on       copyir.com    The paper conveying belt is out of phase       copyir.com The paper conveying belt clutch malfunctions       copyir.com The paper conveying belt home position sensor malfunctions       copyir.com The paper conveying belt home position sensor connector makes poor contact       copyir.com The internal tray is incorrectly inserted
C814    Finisher tray elevation motor problem 2 • The sort tray is not detected in the home position within 30 s of the start of the tray elevation motor rotation       copyir.com    The tray elevation motor connector makes poor contact       copyir.com The tray elevation motor malfunctions       copyir.com Defective finisher main PCB       copyir.com
C817    Finisher front jogger motor problem 2 • While the front jogger is not detected in the home position, the front jogger home position sensor does not detect the jogger within 1       copyir.com5 s of the start of front jogger motor clockwise rotation       copyir.com • After the front jogger is detected in the home position, the front jogger home position sensor still detects the jogger within 0       copyir.com5 s of the start of front jogger motor counterclockwise rotation       copyir.com    The front jogger motor connector makes poor contact       copyir.com The front jogger motor malfunctions       copyir.com The front jogger motor home position sensor connector makes poor contact       copyir.com The front jogger motor home position sensor malfunctions       copyir.com Defective finisher main PCB       copyir.com
C818    Finisher rear jogger motor problem 2 • While the rear jogger is not detected in the home position, the rear jogger home position sensor does not detect the jogger within 1       copyir.com5 s of the start of rear jogger motor clockwise rotation       copyir.com • After the rear jogger is detected in the home position, the rear jogger home position sensor still detects the jogger within 0       copyir.com5 s of the start of rear jogger motor counterclockwise rotation       copyir.com    The rear jogger motor connector makes poor contact       copyir.com The rear jogger motor malfunctions       copyir.com The rear jogger motor home position sensor connector makes poor contact       copyir.com The rear jogger motor home position sensor malfunctions       copyir.com Defective finisher main PCB       copyir.com
C821    Finisher front stapler problem 2 • The front stapler home position sensor does not change state from non-detection to detection within 0       copyir.com2 s of the start of front stapler motor counterclockwise (forward) rotation       copyir.com • During initialization, the front stapler home position sensor does not change state from non-detection to detection within 0       copyir.com6 s of the start of front stapler motor clockwise (reverse) rotation       copyir.com    The front stapler connector makes poor contact       copyir.com The front stapler malfunctions       copyir.com a) The front stapler is blocked with a staple       copyir.com b) The front stapler is broken       copyir.com Defective finisher main PCB       copyir.com
C822    Finisher rear stapler problem 2 • The rear stapler home position sensor does not change state from non-detection to detection within 0       copyir.com2 s of the start of rear stapler motor counterclockwise (forward) rotation       copyir.com • During initialization, the rear stapler home position sensor does not change state from non-detection to detection within 0       copyir.com6 s of the start of rear stapler motor clockwise (reverse) rotation       copyir.com    The rear stapler connector makes poor contact       copyir.com The rear stapler malfunctions       copyir.com a) The rear stapler is blocked with a staple       copyir.com b) The rear stapler is broken       copyir.com Defective finisher main PCB       copyir.com
C920    Deck paper conveying motor problem 1 • No pulse is input within 500 ms of the start-up       copyir.com • No pulse is input within 100 ms of the previous pulse input       copyir.com    The deck paper conveying motor connector makes poor contact       copyir.com Defective deck paper conveying motor PCB       copyir.com The deck paper conveying motor does not rotate correctly (the motor is overloaded)       copyir.com
C921    Paper deck motor 1 problem 1 • No pulse is input within 20 ms of the start-up       copyir.com • No pulse is input within 400 ms of the previous pulse input       copyir.com    Paper deck motor 1 connector makes poor contact       copyir.com Paper deck motor 1 does not rotate correctly (the motor is overloaded)       copyir.com
C922    Paper deck motor 2 problem 1 • No pulse is input within 20 ms of the start-up       copyir.com • No pulse is input within 400 ms of the previous pulse input       copyir.com    Paper deck motor 2 connector makes poor contact       copyir.com Paper deck motor 2 does not rotate correctly (the motor is overloaded)       copyir.com
C923    Right lift position problem 1 • While the paper deck motor is driving, lift upper limit switch 1 detects the right lift reaching the upper limit       copyir.com    Upper limit switch 1 connector makes poor contact       copyir.com Deck level switch 1 connector makes poor contact       copyir.com
C924    Left lift position problem 1 • While the paper deck motor is driving, lift upper limit switch 2 detects the left lift reaching the upper limit       copyir.com    Upper limit switch 2 connector makes poor contact       copyir.com Deck level switch 2 connector makes poor contact       copyir.com

خواندن 1255 دفعه
محتوای بیشتر در این بخش: « کیو سرا میتا km4050 کیو سرا میتا km4530 »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب

Google Analytics Alternative