لمینت MKP
1402-06-04
Menu
195 Product number error
The input product number (11 digits) is not equal to the product identification code ( copyir.com The input product number (11 digits) is not proper ( copyir.com
202 Polygon motor error 1: ON timeout
The polygon mirror motor did not reach the targeted operating speed within T1 seconds after turning on or changing speed ( copyir.com * T1 = Time within which polygon rotation should become stable ( copyir.com Polygon motor/driver board harness loose or disconnected ( copyir.com Polygon motor/driver board defective
203 Polygon motor error 1: OFF timeout
The polygon mirror motor did not leave READY status within 3 seconds after polygon motor switched off ( copyir.com Polygon motor/driver board harness loose or disconnected ( copyir.com Polygon motor/driver board defective
204 Polygon motor error 1: XSCRDY signal error
The “H” status of XSCRDY signal is detected 4 times consecutively during the writing process ( copyir.com Polygon motor/driver board harness loose or disconnected ( copyir.com Polygon motor/driver board defective
220 Laser synchronization detection error: LD0
The laser synchronizing detection signal for the start position of the LD is not output within 500 ms after the LDB unit turns on with the polygon motor rotating normally ( copyir.com Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com efective laser synchronizing detector ( copyir.com Laser beam does not go into the photo detector ( copyir.com Defective GAVD ( copyir.com Defective LD Driver ( copyir.com Defective LDB ( copyir.com Defective BCU ( copyir.com
221 Laser synchronization detection error: except LD0
The laser synchronizing detection signal for the start position of the other LDs are not output within 500 ms after LDB unit turns on with the polygon motor rotating normally ( copyir.com Laser beam does not go into the photo detector ( copyir.com Defective GAVD ( copyir.com Defective LD Driver ( copyir.com Defective LDB ( copyir.com Defective BCU ( copyir.com
230 FGATE ON error
The FGATE signal did not assert within 1 second ( copyir.com (The BCU generates the FGATE signal and sends it to the LD unit when the registration sensor switches on ( copyir.com ) Defective GAVD and PCI bridge ASIC ( copyir.com Defective BCU ( copyir.com Defective controller board ( copyir.com Defective harness between BCU and LDB ( copyir.com
231 FGATE OFF error
The FGATE signal did not go off within 10 seconds after the machine finished writing ( copyir.com (The BCU generates the FGATE signal and sends it to the LD unit when the registration sensor switches on ( copyir.com ) Defective GAVD and PCI bridge ASIC
240 LD error
The IPU detected a problem at the LD unit ( copyir.com Defective LD unit ( copyir.com Disconnect harness ( copyir.com Disconnect LD Driver ( copyir.com
312 Charge roller current leak
The PWM duty output exceeded 50% for longer than 200 ms, indicating a leak in the charge roller current ( copyir.com fective BCU ( copyir.com Cartridge (charge roller) defective ( copyir.com High voltage supply board defective ( copyir.com Disconnect harness ( copyir.com
320 Development Bias leak
The PWM duty output exceeded 50% for longer than 200 ms, indicating a leak in the charge roller current ( copyir.com Bias applying section leak ( copyir.com High voltage supply board defective ( copyir.com Disconnect harness ( copyir.com Development Bias CN loose
440 Primary Transfer PP output leak
The PWM duty output exceeded 50% for longer than 200 ms, indicating a leak in the charge roller current ( copyir.com High voltage supply board defective ( copyir.com Disconnect harness ( copyir.com Development Bias CN loose
500 Main motor lock
The machine does not detect a main motor lock signal within 1 second after the main motor starts to rotate ( copyir.com -or- The machine does not detect a main motor lock signal for 250 ms continuously while the main motor is rotating ( copyir.com Mechanical overload on the drive mechanism ( copyir.com Main motor defectivess ( copyir.com
530 Exhaust fan motor error
The CPU detects an exhaust fan lock signal for more than 2 seconds ( copyir.com Mechanical overload on the Exhaust fan mechanism ( copyir.com Exhaust fan harness loose or broken
531 Reverse Fan Motor error
The CPU detects a Reverse fan lock signal for more than 2 seconds ( copyir.com ?#0 Mechanical overload on the Reverse fan mechanism ( copyir.com Reverse fan harness loose or broken
532 PSU Fan Motor error
The CPU detects a PSU fan lock signal for more than 2 seconds ( copyir.com Mechanical overload on the PSU fan mechanism ( copyir.com PSU fan harness loose or broken
533 PSU2 Fan Motor error
The CPU detects a PSU2 fan lock signal for more than 2 seconds Mechanical overload on the PSU2 fan mechanism ( copyir.com PSU2 fan harness loose or broken
534 AIO Fan Motor error
The CPU detects an AIO fan lock signal for more than 2 seconds ( copyir.com Mechanical overload on the AIO fan mechanism ( copyir.com AIO fan harness loose or broken
541 Fusing thermistor error
The fusing temperature remains lower than 0C for over 7 seconds after the power relay switches on ( copyir.com Thermistor disconnected ( copyir.com Defective thermistor ( copyir.com Fusing unit connected improperlyor
542 Fusing temperature warm-up error
1: Thermistor detects that the rate of heat increase is less than 7 degrees per 2 seconds consecutively 5 times ( copyir.com 2: The fusing temperature did not reach the standby temperature within 24 seconds at the center of the hot roller after the main switch turned on ( copyir.com This SC will appear when condition 1 and 2 occur at the same time ( copyir.com Defective thermistor ( copyir.com Thermistor improper installation ( copyir.com Defective fusing lamp
543 Fusing overheat error – software1
The detected temperature stays at 235°C for 1 second, and this consecutively occurs 10 times ( copyir.com Defective Triac ( copyir.com Defective IOB ( copyir.com Defective engine board
544 Fusing overheat error – Hard 1
The thermistor detects over 250 C ( copyir.com Defective Triac ( copyir.com Defective IOB ( copyir.com Defective engine board ( copyir.com Fusing control error
545 Fusing lamp remains on 1
The fusing lamps remained ON at full capacity for more than 12 seconds after the fusing temperature attains reload temperature ( copyir.com Fusing thermistor defective ( copyir.com Defective fusing lamp ( copyir.com Thermostat actuation
547 Zero cross signal detection error
Zero cross signal is detected consecutively 4 times (for 200 ms) at power on with fusing relay being off ( copyir.com -or- Zero cross interrupts did not issue at the prescribed 3 second intervals ( copyir.com -or- The detection error occurs twice or more in 10 zero cross signal detections ( copyir.com This error is defined when the detected zero cross signal is less than 45 ( copyir.com Defective fusing relay ( copyir.com Defective fusing relay circuit ( copyir.com Shorted +24V fuse on the PSU ( copyir.com Unstable AC power ( copyir.com AC line noise ( copyir.com As for an error due to a high frequency noise interference, this SC will not appear ( copyir.com In this case, SC557 will appear and output the log only ( copyir.com
557 Zero cross frequency error
Zero cross signals of wavelength 50-60 Hz were not detected within 5 seconds after the fusing relay switched on ( copyir.com AC line noise (High frequency)
559 Fuser 3 times jam error
The paper jam counter for the fusing unit reaches 3 ( copyir.com The paper jam counter is cleared if the paper is fed correctly ( copyir.com This SC is activated only when this function is enabled with “Engine Maintenance” (default “OFF”) ( copyir.com Paper jams at the fusing roller
622 Paper tray unit communication error bank 1
Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication ( copyir.com 1 ( copyir.com Disconnect harnesses 2 ( copyir.com Defective Paper tray unit 3 ( copyir.com Defective engine board 4 ( copyir.com External noise
623 Paper tray unit communication error bank 2
Three consecutive errors occur during poll`ing, after the paper tray unit has successful I2C communication ( copyir.com Turn the Power Switch Off and On ( copyir.com Connect the harnesses properly ( copyir.com Replace the Paper tray unit ( copyir.com
624 Paper tray unit communication error bank 3
Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication ( copyir.com Disconnect harnesses ( copyir.com Defective Paper tray unit ( copyir.com External noise
625 Paper tray unit communication error bank 4
Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication ( copyir.com Disconnect harnesses ( copyir.com Defective Paper tray unit ( copyir.com External noise
641 Engine-Controller Communication Error: Non-Response
There was no response to a frame sent from the controller board to the engine ( copyir.com There is still no response after resending frames 3 times in 100 milliseconds Engine board defective ( copyir.com Engine board harness loose, broken, defective ( copyir.com External noise
669 EEPROM communication error
The EEPROM was not connected at power on, or read/write operations on the EEPROM failed ( copyir.com Retrying 3 times after the error detection cannot recover from the error ( copyir.com External noise ( copyir.com Defective EEPROM
670 Engine startup error
The engine board fails to respond within 70 seconds when the machine is turned on ( copyir.com Connections between the engine board and the controller board are loose, disconnected, or damaged
671 Illegal engine board detection error
The machine code sent from the engine board is incorrect when the machine is turn on ( copyir.com Installing another machine’s engine board ( copyir.com Defective engine board ( copyir.com Incorrect NVRAM on the engine board
681 RFID communication error
Machine cannot communicate with the RFID ( copyir.com Retrying 3 times after the error detection when communicating with a RF tag cannot recover from the error ( copyir.com Defective Reader/Writer ( copyir.com Disconnect harnesses ( copyir.com External noise ( copyir.com Defective RFID tag or no ID tag ( copyir.com Defective RFID unit ( copyir.com
683 RFID unit check error
When the unit checking is performed, a transmission error is detected more than 3 times ( copyir.com External noise
688 CTL_PRREQ_N signal does not come ( copyir.com
The PRREQ signal is not received for 130 seconds after paper reaches the registration waiting point ( copyir.com External noise ( copyir.com Defective engine board
690 GAVD communication error
The machine detects an error in the data of the ASIC ( copyir.com Defective GAVD ( copyir.com Defective CPU ( copyir.com Defective BCU ( copyir.com
790 Bank over stacking error
More than 4 PTUs installed ( copyir.com Excess bank stack
819 Fatal kernel error
Due to a control error, a RAM overflow occurred during system processing ( copyir.com One of the following messages was displayed on the operation panel ( copyir.com System program defective ( copyir.com HDD defective ( copyir.com Controller board defective ( copyir.com Optional board defective ( copyir.com
820 Self-Diagnostic Error: CPU
The central processing unit returned an error during the self-diagnostic test ( copyir.com Controller board defective ( copyir.com Software defective ( copyir.com
833 Self-diagnostic error 8: Engine I/F ASIC ASIC (engine board defective)
851 IEEE 1394 I/F error
Driver setting incorrect and cannot be used by the 1394 I/F ( copyir.com NIB (PHY), LINK module defective ( copyir.com Controller board defective ( copyir.com
853 Wireless LAN Error 1
During machine start-up, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802 ( copyir.com 11b or Bluetooth) ( copyir.com Wireless LAN card missing (was removed) ( copyir.com Improper installation of the Wireless LAN card ( copyir.com
854 Wireless LAN Error 2
During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802 ( copyir.com 11b or Bluetooth) ( copyir.com Wireless LAN card missing (was removed) during operation
855 Wireless LAN error 3
An error was detected on the Wireless LAN card (802 ( copyir.com 11b or Bluetooth) ( copyir.com Wireless LAN card defective ( copyir.com Wireless LAN card connection incorrect
856 Wireless LAN error 4
An error was detected on the wireless LAN card (802 ( copyir.com 11b or Bluetooth) ( copyir.com Wireless LAN card defective ( copyir.com PCI connector (to the mother board) loose
857 USB I/F Error
The USB driver is not stable and caused an error ( copyir.com Bad USB card connection ( copyir.com Defective controller board ( copyir.com
858 Data encryption conversion error Key acquisition error
859 HDD data encryption errorn error HDD check error
860 HDD startup error at main power on
HDD is connected but a driver error is detected ( copyir.com The driver does not respond with the status of the HDD within 30 s ( copyir.com HDD is not initialized ( copyir.com Level data is corrupted ( copyir.com HDD is defective
861 HDD re-try failure
At power on the HDD was detected ( copyir.com Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec ( copyir.com Harness between HDD and controller board disconnected, defective ( copyir.com HDD power connector disconnected ( copyir.com HDD defective ( copyir.com Controller board defective ( copyir.com
863 HDD data read failure
The data written to the HDD cannot be read normally, due to bad sectors generated during operation ( copyir.com HDD defective
864 HDD data CRC error
During HDD operation, the HDD cannot respond to an CRC error query ( copyir.com Data transfer did not execute normally while data was being written to the HDD ( copyir.com HDD defective
865 HDD access error
HDD responded to an error during operation for a condition other than those for SC863, 864 ( copyir.com HDD defective ( copyir.com
866 SD card error 1: Confirmation
The machine detects an electronic license error in the application on the SD card in the controller slot immediately after the machine is turned on ( copyir.com The program on the SD card contains electronic confirmation license data ( copyir.com If the program does not contain this license data, or if the result of the check shows that the license data in the program on the SD card is incorrect, then the checked program cannot execute and this SC code is displayed ( copyir.com Program missing from the SD card
867 SD card error 2: SD card removed
The SD card in the boot slot when the machine was turned on was removed while the machine was on ( copyir.com SD card is removed
868 SD card error 3: SD card access
An error occurred while an SD card was used ( copyir.com SD card not inserted correctly ( copyir.com SD card defective ( copyir.com Controller board defective ( copyir.com
870 Address book data error
Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network ( copyir.com The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective ( copyir.com HDD defective ( copyir.com
872 HDD mail receive data error
The machine detected that the HDD was not operating correctly at power on ( copyir.com The machine detected that the HDD was not operating correctly (could neither read nor write) while processing incoming email The machine power was turned off during the HDD access ( copyir.com HDD defective ( copyir.com
873 HDD mail send data error
An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD ( copyir.com HDD defective ( copyir.com
874 Delete All error 2: Data area
An error occurred while the machine deleted data from the HDD ( copyir.com The HDD deleting program detected an error ( copyir.com An error detected during the NVRAM data or others deleting processes ( copyir.com
875 Delete All error 1: HDD
A data error was detected for the HDD/NVRAM after the Delete All option was used ( copyir.com HDD defective
876 Log data abnormal (1) Log data corruption ( copyir.com Software error ( copyir.com NVRAM defective ( copyir.com HDD defective ( copyir.com
877 Data Overwrite Security SD card error
The all delete function did not execute but the Data Overwrite Security Unit (D362) is installed and activated ( copyir.com SD card defective
878 TPM electronic recognition error
The main machine firmware failed to recognize TPM because USB flash is not operating or a system module was updated incorrectly ( copyir.com Controller board defective
900 Electrical total counter error NVRAM incorrect typNVRAM defectiveNVRAM data scrambled ( copyir.com Unexpected error from external source
920 Printer error 1
An internal application error was detected and operation cannot continue ( copyir.com Software defective ( copyir.com Insufficient memory
921 Printer error 2
When the application started, the necessary font was not on the SD card ( copyir.com Font not on the SD card
990 Software performance error
The software attempted to perform an unexpected operation due to: 1) software bug 2) incorrect internal parameter 3) insufficient working memory Software defective
991 Software continuity error
The software attempted to perform an unexpected operation ( copyir.com However, unlike SC990, the object of the error is continuity of the software ( copyir.com Software defective
992 Unexpected Software Error
Software encountered an unexpected operation not defined under any SC code ( copyir.com Software defective ( copyir.com An error undetectable by any other SC code occurredxpect ( copyir.com
995 CPM setting error
998 Application start error
No applications start within 60 sec ( copyir.com after the power is turned on ( copyir.com Loose connection of RAM-DIMM, ROM-DIMM ( copyir.com Software problem ( copyir.com Controller board defective ( copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.