ریکوآفشیو Ricoh Aficio SP5200SF

ریکوآفشیو Ricoh Aficio SP5200SF

ایرادات دستگاههای ریکو براساس کد می باشد. شرکت کپی ایران در نظر دارد تمامی سرویس مانوئلها و رفع ایرادات را در اختیار شما عزیزان قرار دهد.

195    Product number error
The input product number (11 digits) is not equal to the product identification code ( copyir.com     The input product number (11 digits) is not proper ( copyir.com
202    Polygon motor error 1: ON timeout
The polygon mirror motor did not reach the targeted operating speed within T1 seconds after turning on or changing speed ( copyir.com  * T1 = Time within which polygon rotation should become stable ( copyir.com     Polygon motor/driver board harness loose or disconnected ( copyir.com  Polygon motor/driver board defective
203    Polygon motor error 1: OFF timeout
The polygon mirror motor did not leave READY status within 3 seconds after polygon motor switched off ( copyir.com     Polygon motor/driver board harness loose or disconnected ( copyir.com  Polygon motor/driver board defective
204    Polygon motor error 1: XSCRDY signal error
The “H” status of XSCRDY signal is detected 4 times consecutively during the writing process ( copyir.com     Polygon motor/driver board harness loose or disconnected ( copyir.com  Polygon motor/driver board defective
220    Laser synchronization detection error: LD0
The laser synchronizing detection signal for the start position of the LD is not output within 500 ms after the LDB unit turns on with the polygon motor rotating normally ( copyir.com     Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com  efective laser synchronizing detector ( copyir.com  Laser beam does not go into the photo detector ( copyir.com  Defective GAVD ( copyir.com  Defective LD Driver ( copyir.com  Defective LDB ( copyir.com  Defective BCU ( copyir.com
221    Laser synchronization detection error: except LD0
The laser synchronizing detection signal for the start position of the other LDs are not output within 500 ms after LDB unit turns on with the polygon motor rotating normally ( copyir.com     Laser beam does not go into the photo detector ( copyir.com  Defective GAVD ( copyir.com  Defective LD Driver ( copyir.com  Defective LDB ( copyir.com  Defective BCU ( copyir.com
230    FGATE ON error
The FGATE signal did not assert within 1 second ( copyir.com  (The BCU generates the FGATE signal and sends it to the LD unit when the registration sensor switches on ( copyir.com )    Defective GAVD and PCI bridge ASIC ( copyir.com  Defective BCU ( copyir.com  Defective controller board ( copyir.com  Defective harness between BCU and LDB ( copyir.com
231    FGATE OFF error
The FGATE signal did not go off within 10 seconds after the machine finished writing ( copyir.com  (The BCU generates the FGATE signal and sends it to the LD unit when the registration sensor switches on ( copyir.com )    Defective GAVD and PCI bridge ASIC
240    LD error
The IPU detected a problem at the LD unit ( copyir.com     Defective LD unit ( copyir.com  Disconnect harness ( copyir.com  Disconnect LD Driver ( copyir.com
312    Charge roller current leak
The PWM duty output exceeded 50% for longer than 200 ms, indicating a leak in the charge roller current ( copyir.com fective BCU ( copyir.com     Cartridge (charge roller) defective ( copyir.com  High voltage supply board defective ( copyir.com  Disconnect harness ( copyir.com
320    Development Bias leak
The PWM duty output exceeded 50% for longer than 200 ms, indicating a leak in the charge roller current ( copyir.com     Bias applying section leak ( copyir.com  High voltage supply board defective ( copyir.com  Disconnect harness ( copyir.com  Development Bias CN loose
440    Primary Transfer PP output leak
The PWM duty output exceeded 50% for longer than 200 ms, indicating a leak in the charge roller current ( copyir.com     High voltage supply board defective ( copyir.com  Disconnect harness ( copyir.com  Development Bias CN loose
500    Main motor lock
The machine does not detect a main motor lock signal within 1 second after the main motor starts to rotate ( copyir.com  -or- The machine does not detect a main motor lock signal for 250 ms continuously while the main motor is rotating ( copyir.com     Mechanical overload on the drive mechanism ( copyir.com  Main motor defectivess ( copyir.com
530    Exhaust fan motor error
The CPU detects an exhaust fan lock signal for more than 2 seconds ( copyir.com     Mechanical overload on the Exhaust fan mechanism ( copyir.com  Exhaust fan harness loose or broken
531    Reverse Fan Motor error
The CPU detects a Reverse fan lock signal for more than 2 seconds ( copyir.com ?#0    Mechanical overload on the Reverse fan mechanism ( copyir.com  Reverse fan harness loose or broken
532    PSU Fan Motor error
The CPU detects a PSU fan lock signal for more than 2 seconds ( copyir.com     Mechanical overload on the PSU fan mechanism ( copyir.com  PSU fan harness loose or broken
533    PSU2 Fan Motor error
The CPU detects a PSU2 fan lock signal for more than 2 seconds    Mechanical overload on the PSU2 fan mechanism ( copyir.com  PSU2 fan harness loose or broken
534    AIO Fan Motor error
The CPU detects an AIO fan lock signal for more than 2 seconds ( copyir.com     Mechanical overload on the AIO fan mechanism ( copyir.com  AIO fan harness loose or broken
541    Fusing thermistor error
The fusing temperature remains lower than 0C for over 7 seconds after the power relay switches on ( copyir.com     Thermistor disconnected ( copyir.com  Defective thermistor ( copyir.com  Fusing unit connected improperlyor
542    Fusing temperature warm-up error
1: Thermistor detects that the rate of heat increase is less than 7 degrees per 2 seconds consecutively 5 times ( copyir.com  2: The fusing temperature did not reach the standby temperature within 24 seconds at the center of the hot roller after the main switch turned on ( copyir.com  This SC will appear when condition 1 and 2 occur at the same time ( copyir.com     Defective thermistor ( copyir.com  Thermistor improper installation ( copyir.com  Defective fusing lamp
543    Fusing overheat error – software1
The detected temperature stays at 235°C for 1 second, and this consecutively occurs 10 times ( copyir.com     Defective Triac ( copyir.com  Defective IOB ( copyir.com  Defective engine board
544    Fusing overheat error – Hard 1
The thermistor detects over 250 C ( copyir.com     Defective Triac ( copyir.com  Defective IOB ( copyir.com  Defective engine board ( copyir.com  Fusing control error
545    Fusing lamp remains on 1
The fusing lamps remained ON at full capacity for more than 12 seconds after the fusing temperature attains reload temperature ( copyir.com     Fusing thermistor defective ( copyir.com  Defective fusing lamp ( copyir.com  Thermostat actuation
547    Zero cross signal detection error
Zero cross signal is detected consecutively 4 times (for 200 ms) at power on with fusing relay being off ( copyir.com  -or- Zero cross interrupts did not issue at the prescribed 3 second intervals ( copyir.com  -or- The detection error occurs twice or more in 10 zero cross signal detections ( copyir.com  This error is defined when the detected zero cross signal is less than 45 ( copyir.com     Defective fusing relay ( copyir.com  Defective fusing relay circuit ( copyir.com  Shorted +24V fuse on the PSU ( copyir.com  Unstable AC power ( copyir.com  AC line noise ( copyir.com  As for an error due to a high frequency noise interference, this SC will not appear ( copyir.com  In this case, SC557 will appear and output the log only ( copyir.com
557    Zero cross frequency error
Zero cross signals of wavelength 50-60 Hz were not detected within 5 seconds after the fusing relay switched on ( copyir.com     AC line noise (High frequency)
559    Fuser 3 times jam error
The paper jam counter for the fusing unit reaches 3 ( copyir.com  The paper jam counter is cleared if the paper is fed correctly ( copyir.com  This SC is activated only when this function is enabled with “Engine Maintenance” (default “OFF”) ( copyir.com     Paper jams at the fusing roller
622    Paper tray unit communication error bank 1
Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication ( copyir.com     1 ( copyir.com  Disconnect harnesses 2 ( copyir.com  Defective Paper tray unit 3 ( copyir.com  Defective engine board 4 ( copyir.com  External noise
623    Paper tray unit communication error bank 2
Three consecutive errors occur during poll`ing, after the paper tray unit has successful I2C communication ( copyir.com     Turn the Power Switch Off and On ( copyir.com  Connect the harnesses properly ( copyir.com  Replace the Paper tray unit ( copyir.com
624    Paper tray unit communication error bank 3
Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication ( copyir.com     Disconnect harnesses ( copyir.com  Defective Paper tray unit ( copyir.com  External noise
625    Paper tray unit communication error bank 4
Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication ( copyir.com     Disconnect harnesses ( copyir.com  Defective Paper tray unit ( copyir.com  External noise
641    Engine-Controller Communication Error: Non-Response
There was no response to a frame sent from the controller board to the engine ( copyir.com  There is still no response after resending frames 3 times in 100 milliseconds    Engine board defective ( copyir.com  Engine board harness loose, broken, defective ( copyir.com  External noise
669    EEPROM communication error
The EEPROM was not connected at power on, or read/write operations on the EEPROM failed ( copyir.com  Retrying 3 times after the error detection cannot recover from the error ( copyir.com     External noise ( copyir.com  Defective EEPROM
670    Engine startup error
The engine board fails to respond within 70 seconds when the machine is turned on ( copyir.com     Connections between the engine board and the controller board are loose, disconnected, or damaged
671    Illegal engine board detection error
The machine code sent from the engine board is incorrect when the machine is turn on ( copyir.com     Installing another machine’s engine board ( copyir.com  Defective engine board ( copyir.com  Incorrect NVRAM on the engine board
681    RFID communication error
Machine cannot communicate with the RFID ( copyir.com  Retrying 3 times after the error detection when communicating with a RF tag cannot recover from the error ( copyir.com     Defective Reader/Writer ( copyir.com  Disconnect harnesses ( copyir.com  External noise ( copyir.com  Defective RFID tag or no ID tag ( copyir.com  Defective RFID unit ( copyir.com
683    RFID unit check error
When the unit checking is performed, a transmission error is detected more than 3 times ( copyir.com     External noise
688    CTL_PRREQ_N signal does not come ( copyir.com
The PRREQ signal is not received for 130 seconds after paper reaches the registration waiting point ( copyir.com     External noise ( copyir.com  Defective engine board
690    GAVD communication error
The machine detects an error in the data of the ASIC ( copyir.com     Defective GAVD ( copyir.com  Defective CPU ( copyir.com  Defective BCU ( copyir.com
790    Bank over stacking error
More than 4 PTUs installed ( copyir.com     Excess bank stack
819    Fatal kernel error
Due to a control error, a RAM overflow occurred during system processing ( copyir.com  One of the following messages was displayed on the operation panel ( copyir.com     System program defective ( copyir.com  HDD defective ( copyir.com  Controller board defective ( copyir.com  Optional board defective ( copyir.com
820    Self-Diagnostic Error: CPU
The central processing unit returned an error during the self-diagnostic test ( copyir.com     Controller board defective ( copyir.com  Software defective ( copyir.com
833    Self-diagnostic error 8: Engine I/F ASIC    ASIC (engine board defective)
851    IEEE 1394 I/F error
Driver setting incorrect and cannot be used by the 1394 I/F ( copyir.com     NIB (PHY), LINK module defective ( copyir.com  Controller board defective ( copyir.com
853    Wireless LAN Error 1
During machine start-up, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802 ( copyir.com 11b or Bluetooth) ( copyir.com     Wireless LAN card missing (was removed) ( copyir.com  Improper installation of the Wireless LAN card ( copyir.com
854    Wireless LAN Error 2
During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802 ( copyir.com 11b or Bluetooth) ( copyir.com     Wireless LAN card missing (was removed) during operation
855    Wireless LAN error 3
An error was detected on the Wireless LAN card (802 ( copyir.com 11b or Bluetooth) ( copyir.com     Wireless LAN card defective ( copyir.com  Wireless LAN card connection incorrect
856    Wireless LAN error 4
An error was detected on the wireless LAN card (802 ( copyir.com 11b or Bluetooth) ( copyir.com     Wireless LAN card defective ( copyir.com  PCI connector (to the mother board) loose
857    USB I/F Error
The USB driver is not stable and caused an error ( copyir.com     Bad USB card connection ( copyir.com  Defective controller board ( copyir.com
858    Data encryption conversion error    Key acquisition error
859    HDD data encryption errorn error    HDD check error
860    HDD startup error at main power on
HDD is connected but a driver error is detected ( copyir.com  The driver does not respond with the status of the HDD within 30 s ( copyir.com     HDD is not initialized ( copyir.com  Level data is corrupted ( copyir.com  HDD is defective
861    HDD re-try failure
At power on the HDD was detected ( copyir.com  Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec ( copyir.com     Harness between HDD and controller board disconnected, defective ( copyir.com  HDD power connector disconnected ( copyir.com  HDD defective ( copyir.com  Controller board defective ( copyir.com
863    HDD data read failure
The data written to the HDD cannot be read normally, due to bad sectors generated during operation ( copyir.com     HDD defective
864    HDD data CRC error
During HDD operation, the HDD cannot respond to an CRC error query ( copyir.com  Data transfer did not execute normally while data was being written to the HDD ( copyir.com     HDD defective
865    HDD access error
HDD responded to an error during operation for a condition other than those for SC863, 864 ( copyir.com     HDD defective ( copyir.com
866    SD card error 1: Confirmation
The machine detects an electronic license error in the application on the SD card in the controller slot immediately after the machine is turned on ( copyir.com  The program on the SD card contains electronic confirmation license data ( copyir.com  If the program does not contain this license data, or if the result of the check shows that the license data in the program on the SD card is incorrect, then the checked program cannot execute and this SC code is displayed ( copyir.com     Program missing from the SD card
867    SD card error 2: SD card removed
The SD card in the boot slot when the machine was turned on was removed while the machine was on ( copyir.com     SD card is removed
868    SD card error 3: SD card access
An error occurred while an SD card was used ( copyir.com     SD card not inserted correctly ( copyir.com  SD card defective ( copyir.com  Controller board defective ( copyir.com
870    Address book data error
Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network ( copyir.com  The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective ( copyir.com     HDD defective ( copyir.com
872    HDD mail receive data error
The machine detected that the HDD was not operating correctly at power on ( copyir.com  The machine detected that the HDD was not operating correctly (could neither read nor write) while processing incoming email    The machine power was turned off during the HDD access ( copyir.com  HDD defective ( copyir.com
873    HDD mail send data error
An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD ( copyir.com     HDD defective ( copyir.com
874    Delete All error 2: Data area
An error occurred while the machine deleted data from the HDD ( copyir.com     The HDD deleting program detected an error ( copyir.com  An error detected during the NVRAM data or others deleting processes ( copyir.com
875    Delete All error 1: HDD
A data error was detected for the HDD/NVRAM after the Delete All option was used ( copyir.com     HDD defective
876    Log data abnormal (1)    Log data corruption ( copyir.com  Software error ( copyir.com  NVRAM defective ( copyir.com  HDD defective ( copyir.com
877    Data Overwrite Security SD card error
The all delete function did not execute but the Data Overwrite Security Unit (D362) is installed and activated ( copyir.com     SD card defective
878    TPM electronic recognition error
The main machine firmware failed to recognize TPM because USB flash is not operating or a system module was updated incorrectly ( copyir.com     Controller board defective
900    Electrical total counter error    NVRAM incorrect typNVRAM defectiveNVRAM data scrambled ( copyir.com  Unexpected error from external source
920    Printer error 1
An internal application error was detected and operation cannot continue ( copyir.com     Software defective ( copyir.com  Insufficient memory
921    Printer error 2
When the application started, the necessary font was not on the SD card ( copyir.com     Font not on the SD card
990    Software performance error
The software attempted to perform an unexpected operation due to: 1) software bug 2) incorrect internal parameter 3) insufficient working memory    Software defective
991    Software continuity error
The software attempted to perform an unexpected operation ( copyir.com  However, unlike SC990, the object of the error is continuity of the software ( copyir.com     Software defective
992    Unexpected Software Error
Software encountered an unexpected operation not defined under any SC code ( copyir.com     Software defective ( copyir.com  An error undetectable by any other SC code occurredxpect ( copyir.com
995    CPM setting error
998    Application start error
No applications start within 60 sec ( copyir.com  after the power is turned on ( copyir.com     Loose connection of RAM-DIMM, ROM-DIMM ( copyir.com  Software problem ( copyir.com  Controller board defective ( copyir.com