لمینت MKP
1402-06-04
Menu
101 Exposure lamp error
The peak white level is less than 64/255 digits (8 bits) when scanning the shading plate ( copyir.com • Exposure lamp defective • Lamp stabilizer defective • Exposure lamp connector defective • Standard white plate dirty • Scanner mirror or scanner lens out of position or dirty
120 Scanner home position error 1
The scanner home position sensor does not detect the “OFF” condition during operation ( copyir.com • Scanner motor driver defective • Scanner motor defective • Harness between SIO board and scanner motor disconnected • Scanner HP sensor defective • Harness between SIO and HP sensor disconnected
121 Scanner home position error 2
The scanner home position sensor does not detect the “ON” condition during operation ( copyir.com • Scanner motor driver defective • Scanner motor defective • Harness between SIO board and scanner motor disconnected • Scanner HP sensor defective • Harness between SIO and HP sensor disconnected
141 Black level detection error The black level cannot be adjusted within the target value during the zero clamp ( copyir.com • Harness disconnected • Defective SBU
142 White level detection error
The white level cannot be adjusted within the target during auto gain control ( copyir.com • Dirty exposure glass or optics section • SBU board defective • Exposure lamp defective • Lamp stabilizer defective • Scanner motor defective
144 SBU communication error
The SBU connection cannot be detected at power on or recovery from the energy save mode ( copyir.com • Defective SBU • Defective harness • Defective detection port on the BICU
161-001 The error result of self-diagnostic by the ASIC on the BICU is detected ( copyir.com • Defective BICU • Defective connection between BICU and SBU
161-002 IPU error
Detected an error during an access to the Ri ( copyir.com • Defective BICU board
165 Copy Data Security Unit error
• The copy data security board is not detected when the copy data security function is set “ON” with the initial setting ( copyir.com • A device check error occurs when the copy data security function is set “ON” with the initial setting ( copyir.com • Incorrect installation of the copy data security board • Defective copy data security board
185 CIS communication error Error occurs during ASIC register’s automatic initialization on the CIS, or during transmission between the CIS – DF ( copyir.com • Harness between the CIS – DF is disconnected • CIS defective
186 CIS LED error
LED on the CIS causes an error ( copyir.com • During initializing, the ratio of the average between leading-edge area and rear-edge is out of range ( copyir.com • During scanning, the shading data peak is under the standard value ( copyir.com • Harness CN210 and CN220 on the DF are disconnected ( copyir.com
187 CIS black level error
The black level scanned by CIS is abnormal ( copyir.com The black level average of R, G or B is not within range (2 to 62) ( copyir.com 0 < Calibrated Black data level < 255 (10bit) ( copyir.com • Defective CIS
188 CIS white level error
The shading data peak detected from the CIS is abnormal ( copyir.com • Defective CIS
189 CIS gray balance adjustment error
The adjustment error occurs during the test after adjusting the gray balance ( copyir.com • Defective CIS
195 Serial Number Mismatch
• Serial number stored in the memory does not have the correct code ( copyir.com • NVRAM defective • BICU replaced without original NVRAM
202 Polygon motor error 1: ON timeout
The polygon mirror motor does not reach the targeted operating speed within the specified time after turning on or changing speed • Defective or disconnected harness to polygon motor driver board • Defective polygon motor driver board • Defective polygon motor ( copyir.com
203 Polygon motor error 2: OFF timeout
The polygon mirror motor does leave the READY status within 3 seconds after the polygon motor switches off ( copyir.com • Disconnected or defective harness to polygon motor driver board • Defective polygon motor driver board • Defective polygon motor
204 Polygon motor error 3: XSCRDY signal error
The SCRDY_N signal goes HIGH (inactive) while the laser diode is firing ( copyir.com • Disconnected or defective harness to polygon motor driver board • Defective polygon motor • Defective polygon motor driver board
210 Laser synchronizing detection error: end position [K]
The laser synchronizing detection signal for the end position of LDB [K], [Y], [M], [C] is not detected for one second after the LDB unit turned on when detecting the main scan magnification Disconnected or defective harness to synchronizing detector for end position ( copyir.com Defective synchronizing detector board ( copyir.com Defective LD board or driver ( copyir.com Defective BICU ( copyir.com
211 Laser synchronizing detection error: end position [Y]
The laser synchronizing detection signal for the end position of LDB [K], [Y], [M], [C] is not detected for one second after the LDB unit turned on when detecting the main scan magnification Disconnected or defective harness to synchronizing detector for end position ( copyir.com Defective synchronizing detector board ( copyir.com Defective LD board or driver ( copyir.com Defective BICU ( copyir.com
212 Laser synchronizing detection error: end position [M]
The laser synchronizing detection signal for the end position of LDB [K], [Y], [M], [C] is not detected for one second after the LDB unit turned on when detecting the main scan magnification Disconnected or defective harness to synchronizing detector for end position ( copyir.com Defective synchronizing detector board ( copyir.com Defective LD board or driver ( copyir.com Defective BICU ( copyir.com
213 Laser synchronizing detection error: end position [C]
The laser synchronizing detection signal for the end position of LDB [K], [Y], [M], [C] is not detected for one second after the LDB unit turned on when detecting the main scan magnification Disconnected or defective harness to synchronizing detector for end position ( copyir.com Defective synchronizing detector board ( copyir.com Defective LD board or driver ( copyir.com Defective BICU ( copyir.com
220 Laser synchronizing detection error: start position [K]: LD0
The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective IPU
221 Laser synchronizing detection error: start position [K]: LD1
The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective IPU
222 Laser synchronizing detection error: start position [Y]: LD0
The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective IPU
223 Laser synchronizing detection error: start position [Y]: LD1
The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective IPU
224 Laser synchronizing detection error: start position [M]: LD0
The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective IPU
225 Laser synchronizing detection error: start position [M]: LD1
The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective IPU
226 Laser synchronizing detection error: start position [C]: LD0
The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective IPU
227 Laser synchronizing detection error: start position [C]: LD1
The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective IPU
230 FGATE ON error: K
The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [K] ( copyir.com Defective ASIC (Lupus) ( copyir.com Poor connection between controller and BICU ( copyir.com Defective BICU ( copyir.com
231 FGATE OFF error: K
• The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K] ( copyir.com • The PFGATE ON signal still asserts when the next job starts ( copyir.com • Defective ASIC (Lupus) • Poor connection between controller and BICU ( copyir.com • Defective BICU
232 FGATE ON error: Y
The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [Y] ( copyir.com Defective ASIC (Lupus) ( copyir.com Poor connection between controller and BICU ( copyir.com Defective BICU ( copyir.com
233 FGATE OFF error: YT
he PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [Y] ( copyir.com The PFGATE ON signal still asserts when the next job starts ( copyir.com Defective ASIC (Lupus) ( copyir.com Poor connection between controller and BICU ( copyir.com Defective BICU ( copyir.com
234 FGATE ON error: M
The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [M] ( copyir.com Defective ASIC (Lupus) ( copyir.com Poor connection between controller and BICU ( copyir.com Defective BICU ( copyir.com
235 FGATE OFF error: M
The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [M] ( copyir.com The PFGATE ON signal still asserts when the next job starts ( copyir.com Defective ASIC (Lupus) ( copyir.com Poor connection between controller and BICU ( copyir.com Defective BICU ( copyir.com
236 FGATE ON error: C
The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [C] ( copyir.com Defective ASIC (Lupus) ( copyir.com Poor connection between controller and BICU ( copyir.com Defective BICU ( copyir.com
237 FGATE OFF error: C
The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [C] ( copyir.com The PFGATE ON signal still asserts when the next job starts ( copyir.com Defective ASIC (Lupus) ( copyir.com Poor connection between controller and BICU ( copyir.com Defective BICU ( copyir.com
240 LD error: Bk
The BICU detects LDB error a few times consecutively when LDB unit turns on after LDB initialization ( copyir.com Worn-out LD ( copyir.com Disconnected or broken harness of the LD
241 LD error: Y
The BICU detects LDB error a few times consecutively when LDB unit turns on after LDB initialization ( copyir.com Worn-out LD ( copyir.com Disconnected or broken harness of the LD
242 LD error: M
The BICU detects LDB error a few times consecutively when LDB unit turns on after LDB initialization ( copyir.com Worn-out LD ( copyir.com Disconnected or broken harness of the LD
243 LD error: C
The BICU detects LDB error a few times consecutively when LDB unit turns on after LDB initialization ( copyir.com Worn-out LD ( copyir.com Disconnected or broken harness of the LD
285 Line position adjustment (MUSIC) error
Line position adjustment fails four consecutive times ( copyir.com • Pattern sampling error ( insufficient image density ) • Defective ID sensors for the line position adjustment • Defective image transfer belt unit • Defective PCU(s) • Defective laser optics housing unit
312 Charge P ( copyir.com P ( copyir.com output error [K]
The feedback voltage of the charge AC for each color is 0 ( copyir.com 3 V or less for 0 ( copyir.com 2 seconds after the charge AC has turned on ( copyir.com • Disconnected or broken harnesses of the HVPS • Defective PCDU • Defective HVPS
313 Charge P ( copyir.com P ( copyir.com output error [M]
The feedback voltage of the charge AC for each color is 0 ( copyir.com 3 V or less for 0 ( copyir.com 2 seconds after the charge AC has turned on ( copyir.com • Disconnected or broken harnesses of the HVPS • Defective PCDU • Defective HVPS
314 Charge P ( copyir.com P ( copyir.com output error [C]
The feedback voltage of the charge AC for each color is 0 ( copyir.com 3 V or less for 0 ( copyir.com 2 seconds after the charge AC has turned on ( copyir.com • Disconnected or broken harnesses of the HVPS • Defective PCDU • Defective HVPS
315 Charge P ( copyir.com P ( copyir.com output error [Y]
The feedback voltage of the charge AC for each color is 0 ( copyir.com 3 V or less for 0 ( copyir.com 2 seconds after the charge AC has turned on ( copyir.com • Disconnected or broken harnesses of the HVPS • Defective PCDU • Defective HVPS
360 TD sensor (Vt high) error 1: K
The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4 ( copyir.com 7V) with SP3020-002 for twenty counts ( copyir.com The [Vt – Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5 ( copyir.com 0V) with SP3020-001 ( copyir.com Black, magenta, cyan, or yellow TD sensor disconnected ( copyir.com Harness between TD sensor and PCU defective ( copyir.com Defective TD sensor ( copyir.com
361 TD sensor (Vt high) error 1: M
The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4 ( copyir.com 7V) with SP3020-002 for twenty counts ( copyir.com The [Vt – Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5 ( copyir.com 0V) with SP3020-001 ( copyir.com Black, magenta, cyan, or yellow TD sensor disconnected ( copyir.com Harness between TD sensor and PCU defective ( copyir.com Defective TD sensor ( copyir.com
362 TD sensor (Vt high) error 1: C
The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4 ( copyir.com 7V) with SP3020-002 for twenty counts ( copyir.com The [Vt – Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5 ( copyir.com 0V) with SP3020-001 ( copyir.com Black, magenta, cyan, or yellow TD sensor disconnected ( copyir.com Harness between TD sensor and PCU defective ( copyir.com Defective TD sensor ( copyir.com
363 TD sensor (Vt high) error 1: Y
The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4 ( copyir.com 7V) with SP3020-002 for twenty counts ( copyir.com The [Vt – Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5 ( copyir.com 0V) with SP3020-001 ( copyir.com Black, magenta, cyan, or yellow TD sensor disconnected ( copyir.com Harness between TD sensor and PCU defective ( copyir.com Defective TD sensor ( copyir.com
364 TD sensor (Vt high) error 2: K
The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0 ( copyir.com 5V) for 10 counts ( copyir.com TD sensor harness disconnected, loose, defective ( copyir.com A drawer connector disconnected, loose, defective ( copyir.com TD sensor defectiver ( copyir.com
365 TD sensor (Vt high) error 2: M
The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0 ( copyir.com 5V) for 10 counts ( copyir.com TD sensor harness disconnected, loose, defective ( copyir.com A drawer connector disconnected, loose, defective ( copyir.com TD sensor defectiver ( copyir.com
366 TD sensor (Vt high) error 2: C
The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0 ( copyir.com 5V) for 10 counts ( copyir.com TD sensor harness disconnected, loose, defective ( copyir.com A drawer connector disconnected, loose, defective ( copyir.com TD sensor defectiver ( copyir.com
367 TD sensor (Vt high) error 2: Y
The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0 ( copyir.com 5V) for 10 counts ( copyir.com TD sensor harness disconnected, loose, defective ( copyir.com A drawer connector disconnected, loose, defective ( copyir.com TD sensor defectiver ( copyir.com
372 TD sensor adjustment error: K
During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2 ( copyir.com 7V) +- 0 ( copyir.com 2V Heat seal not removed from a new developer pack ( copyir.com TD harness sensor disconnected, loose or defective ( copyir.com TD sensor defective ( copyir.com Harness between TD sensor and drawer disconnected, defective ( copyir.com
373 TD sensor adjustment error: M
During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2 ( copyir.com 7V) +- 0 ( copyir.com 2V Heat seal not removed from a new developer pack ( copyir.com TD harness sensor disconnected, loose or defective ( copyir.com TD sensor defective ( copyir.com Harness between TD sensor and drawer disconnected, defective ( copyir.com
374 TD sensor adjustment error: C
During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2 ( copyir.com 7V) +- 0 ( copyir.com 2V Heat seal not removed from a new developer pack ( copyir.com TD harness sensor disconnected, loose or defective ( copyir.com TD sensor defective ( copyir.com Harness between TD sensor and drawer disconnected, defective ( copyir.com
375 TD sensor adjustment error: Y
During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2 ( copyir.com 7V) +- 0 ( copyir.com 2V Heat seal not removed from a new developer pack ( copyir.com TD harness sensor disconnected, loose or defective ( copyir.com TD sensor defective ( copyir.com Harness between TD sensor and drawer disconnected, defective ( copyir.com
380 Drum gear position sensor error: K
The machine does not detect the drum position signal for 3 seconds at the drum phase adjustment ( copyir.com • Dirty or defective drum gear position sensor
381 Drum gear position sensor error: M
The machine does not detect the drum position signal for 3 seconds at the drum phase adjustment ( copyir.com • Dirty or defective drum gear position sensor
382 Drum gear position sensor error: C
The machine does not detect the drum position signal for 3 seconds at the drum phase adjustment ( copyir.com • Dirty or defective drum gear position sensor
383 Drum gear position sensor error: Y
The machine does not detect the drum position signal for 3 seconds at the drum phase adjustment ( copyir.com • Dirty or defective drum gear position sensor
396 Drum/Development motor error: K
The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on ( copyir.com • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system
397 Drum/Development motor error: M
The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on ( copyir.com • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system
398 Drum/Development motor error: C
The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on ( copyir.com • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system
399 Drum/Development motor error: Y
The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on ( copyir.com • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system
400 ID sensor adjustment error
When the Vsg error counter reaches “3”, the machine detects “SC400” ( copyir.com The Vsg error counter counts “1” when the Vsg detected by ID sensor is more than the value (default: 4 ( copyir.com 5V) specified with SP3324-005 or less than the value (default: 3 ( copyir.com 5V) specified with SP3324-006 ( copyir.com • Dirty or defective ID sensor • Defective ID sensor shutter
441 Image transfer unit motor error
The motor LOCK signal is not detected for more than two seconds while the motor START signal is on ( copyir.com • Motor overload • Defective image transfer unit motor
442 Image transfer belt contact motor error
The image transfer belt contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates ( copyir.com • Dirty image transfer belt contact sensor • Defective image transfer belt contact motor • Disconnected connector of image transfer belt contact sensor or motor • Disconnected cable
443 Image transfer unit error
The machine detects the encoder sensor error ( copyir.com • Defective encoder sensor • Image transfer unit installation error • Defective image transfer unit motor
452 Paper transfer unit contact error
The paper transfer unit contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates ( copyir.com • Defective paper transfer unit contact sensor • Defective paper transfer unit contact motor • Broken +24V fuse on PSU • Defective IOB
460 Separation power pack output error
An interrupt checks the status of the power pack every 20 ms ( copyir.com This SC is issued if the BICU detects a short in the power pack 10 times at D(ac) ( copyir.com • Damaged insulation on the high-voltage supply cable • Damaged insulation around the high-voltage power supply ( copyir.com
490 Toner transport motor error
The LOCK signal is not detected for 2 seconds when the transport motor turns on ( copyir.com • Toner transport motor overload • Disconnected or broken harness • Defective toner transport motor • Opened +24V fuse on the PSU • Defective interlock switch
491 High voltage power: Drum/ development bias output error
An error signal is detected for 0 ( copyir.com 2 seconds when charging the drum or development ( copyir.com • High voltage leak • Broken harness • Defective drum unit or development unit • Defective high voltage supply unit
492 High voltage power: Image transfer/ paper transfer bias output error
An error signal is detected for 0 ( copyir.com 2 seconds when charging the separation, image transfer bet or paper transfer roller ( copyir.com • High voltage leak • Broken harness • Defective image transfer belt unit or paper transfer unit • Defective high voltage supply unit
498 Temperature and humidity sensor error 2
• The thermistor output of the temperature sensor was not within the prescribed range (0 ( copyir.com 5V to 4 ( copyir.com 2V) ( copyir.com • The thermistor output of the humidity sensor was not within the prescribed range (0 ( copyir.com 01V to 2 ( copyir.com 4V) ( copyir.com • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective
501 Paper Tray 1 error
• When the tray lift motor rotates counterclockwise, (if the upper limit is not detected within 10 seconds), the machine asks the user to reset the tray ( copyir.com • When the tray lift motor rotates clockwise, (if the upper limit is not detected within 1 ( copyir.com 5 seconds), the machine asks the user to reset the tray ( copyir.com If one of these conditions occurs three consecutive times, the SC is generated ( copyir.com • Disconnected or defective paper lift sensor • Disconnected or defective tray lift motor • Defective bottom plate lift mechanism • Too much paper in the tray • Defective IOB
502 Paper Tray 2 error
• When the tray lift motor rotates counterclockwise, (if the upper limit is not detected within 10 seconds), the machine asks the user to reset the tray ( copyir.com • When the tray lift motor rotates clockwise, (if the upper limit is not detected within 1 ( copyir.com 5 seconds), the machine asks the user to reset the tray ( copyir.com If one of these conditions occurs three consecutive times, the SC is generated ( copyir.com • Disconnected or defective paper lift sensor • Disconnected or defective tray lift motor • Defective bottom plate lift mechanism • Too much paper in the tray • Defective IOB
503-01 Tray 3 error (Paper Feed Unit or LCT)
For the paper feed unit: • When the tray lift motor is turned on, the upper limit is not detected within 10 seconds For the LCT: • SC 503-01 occurs if the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift or lower the tray ( copyir.com For the paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection • Defective upper limit sensor or connector disconnection • Defective tray lift motor or connector disconnection
503-02 Tray 3 error (Paper Feed Unit or LCT)
This SC is generated if the following condition occurs 3 consecutive times ( copyir.com For the paper feed unit: • When the tray lowers, the tray lift sensor does not go off within 1 ( copyir.com 5 sec ( copyir.com For the LCT: • When the main switch is turned on or when the LCT is set, if the end fence is not in the home position (home position sensor ON), the tray lift motor stops ( copyir.com • If the upper limit does not go off for 1 ( copyir.com 5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on ( copyir.com For the paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection
504-01 Tray 4 error (Paper Feed Unit or LCT) For the two-tray paper feed unit When the tray lift motor is turned on, the upper limit is not detected within 10 seconds ( copyir.com If this condition occurs three consecutive times, the SC is generated ( copyir.com For the LCT If the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift up or lower the tray • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection
504-02 Tray 4 error (3 Tray Paper Feed Unit)
This SC is generated if the following condition occurs 3 consecutive times ( copyir.com For the two-tray paper feed unit • When the tray lowers, the tray lift sensor does not go off within 1 ( copyir.com 5 sec ( copyir.com For the LCT • If the upper limit does not go off for 1 ( copyir.com 5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on ( copyir.com • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection
505-1 5th tray lift malfunction (optional LCT)
This SC is generated if the following condition occurs: • When the tray lift sensor of the LCT 1200-sheet does not go on after the tray lift motor has turned on to lift the paper tray ( copyir.com • When the tray lift sensor of the LCT 1200-sheet does not go off after the tray lift motor has turned on to lower the paper tray ( copyir.com • When the tray lift sensor of the LCT 1200-sheet does not go on after the pickup roller solenoid has turned on at power on ( copyir.com • Tray lift motor defective or disconnected • Tray lift sensor defective or disconnected
505-2 5th tray lift malfunction (optional LCT)
Both tray lift sensor and lower limit sensor are turned on at the same time when the main power is turned on or the right door is closed ( copyir.com • Tray lift motor defective or disconnected • Tray lift sensor defective or disconnected • Lowe limit sensor defective or disconnected
530 Fusing fan error
The IOB does not receive the lock signal 10 seconds after turning on the fusing fan ( copyir.com • Defective fusing fan motor or connector disconnection • Defective IOB
531 Ventilation fan (at the left side of the machine) motor-front/rear error
The IOB does not receive the lock signal for 2 seconds after turning on the ventilation fan motor-front/rear ( copyir.com • Defective ventilation fan motor-front or rear
532 IH coil fan error
The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on ( copyir.com • Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB
533 IH inverter fan error
The machine does not detect the fan motor lock signal for 2 seconds while the IH inverter fan turns on ( copyir.com • Disconnected harness • Overload on the IH inverter fan motor • Defective IH inverter fan motor • Defective IOB
534 Second duct fan error
The machine does not detect the fan motor lock signal for 2 seconds while the second duct fan turns on ( copyir.com • Disconnected harness • Overload on the second duct fan motor • Defective second duct motor • Defective IOB
535 Paper exit fan error
The machine does not detect the fan motor lock signal for 2 seconds while the paper exit fan turns on ( copyir.com • Disconnected harness • Overload on the paper exit fan motor • Defective paper exit motor • Defective IOB
536 Controller fan error
The motor lock signal error is detected for 10 seconds after the motor lock signal was first detected ( copyir.com • Defective controller fan motor • Disconnected or defective harness • Defective IOB
540 Fusing/Paper exit motor error
The IOB does not receive the lock signal 10 seconds after turning on the fusing/ paper exit motor ( copyir.com • Motor overload • Defective fusing/paper exit motor
541 Heating roller thermopile error
The temperature measured by the heating roller thermopile does not reach 0°C for 6 seconds ( copyir.com • Loose connection of the heating roller thermopile • Defective heating roller thermopile • Defective thermopile
542 Heating roller warm-up error 1
• The heating roller temperature does not reach 80°C for 20 seconds after the IH inverter turned on ( copyir.com • The center temperature of the heating roller does not reach the ready temperature for 90 seconds after the IH inverter turned on ( copyir.com • Dirty or defective thermopile • Defective thermistor • Defective heating roller lamp
543 Heating roller fusing lamp overheat 1 (software error)
The detected fusing temperature stays at 230°C for 1 second ( copyir.com • Defective PSU • Defective IOB • Defective BICU
544 Heating roller fusing lamp overheat 1 (hardware error)
During stand-by mode or a print job, the detected heating roller temperature reaches 250 °C ( copyir.com • Defective PSU • Defective IOB • Defective BICU • Defective fusing control system
547 Zero cross error
• The zero cross signal is detected three times even though the heater relay is off when turning on the main power ( copyir.com • The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door ( copyir.com • The detection error occurs twice or more in the 11 zero cross signal detections ( copyir.com This error is defined when the detected zero cross signal is less than 45 ( copyir.com • Defective fusing lamp relay • Defective fusing lamp relay circuit • Unstable power supply
548 Fusing unit rotation error
The heating roller rotation sensor does not detect change in the actuator for 0 ( copyir.com 5 seconds after the fusing/paper exit motor has turned on ( copyir.com • Defective fusing/paper exit motor • Deformed actuator for the heating roller rotation sensor • Defective heating roller rotation sensor • Broken connection between IH inverter and IOB • Incorrectly set fusing unit
551 Heating roller thermistor error
The temperature at the end of the heating roller measured by the heating roller thermistor does not reach 0°C for 7 seconds ( copyir.com • Loose connection of pressure roller thermistor • Defective heating roller thermistor
552 Heating roller warm-up error 2
• The heating roller temperature does not reach 80°C for 20 seconds after the IH inverter turned on ( copyir.com • The temperature at the end of the heating roller does not reach the ready temperature for 89 seconds after the IH inverter turned on ( copyir.com • Defective heating roller thermistor • Defective IH inverter
553 Heating roller overheat (software error)
The detected heating roller temperature stays at 245°C or more for 1 second ( copyir.com • Defective PSU • Defective IOB • Defective BICU
554 Heating roller overheat (hardware error)
The heating roller thermistor detects 250°C or more ( copyir.com • Defective PSU • Defective IOB • Defective BICU • Defective fusing control system
557 Zero cross frequency error
When the zero cross signal is 66 or more and it is detected 10 times or more in 11 detections, the machine determines that input 60 Hz and SC557 occurs ( copyir.com • Noise (High frequency) • Defective PSU
559 Consecutive fusing jam
The paper jam counter for the fusing unit reaches 3 times ( copyir.com The paper jam counter is cleared if the paper is fed correctly ( copyir.com This SC is activated only when SP1159-001 is set to “1” (default “0”) ( copyir.com • Paper jam in the fusing unit ( copyir.com
561 Pressure roller thermistor error: End
The temperature at the end of the pressure roller measured by the thermistor does not reach 0°C for 37 seconds ( copyir.com • Loose connection of the thermistor • Defective thermistor
563 Pressure roller overheat 3 (software error)
The detected pressure roller temperature stays at 215°C or more for 1 second ( copyir.com • Defective PSU • Defective IOB • Defective BICU
564 Pressure roller overheat 3 (hardware error)
The thermistor detects 220°C or more ( copyir.com • Defective PSU • Defective IOB • Defective BICU • Defective fusing control system
565 Pressure roller fusing lamp consecutive full power
When the fusing unit is not running in the ready condition, the pressure roller fusing lamp keeps ON full power for 300 seconds or more ( copyir.com • Broken pressure roller fusing lamp • Defective pressure roller thermistor more ( copyir.com
569 Pressure roller contact sensor error
Pressure roller contact sensor does not detect the pressure roller position three times ( copyir.com • Broken or defective pressure roller contact sensor • Deformed or broken pressure roller contact sensor feeler • Defective pressure roller contact motor • Defective fusing unit
571 Pressure roller thermistor error: Center
The center temperature of the pressure roller measured by the thermistor does not reach 0°C for 37 seconds ( copyir.com • Loose connection of the thermistor • Defective thermistor
581 IH inverter input voltage error
The IH inverter detects 70 V or less/150 V or more for 10 seconds ( copyir.com The IH inverter detects 160 V or less/300 V or more for 10 seconds ( copyir.com • Unusual input voltage • Defective IH inverter
582 IH inverter current error at power on
The output current from the IH inverter does not reach the proper value when the IH inverter turns on ( copyir.com • Disconnected power input terminal 1 and 2 • Defective IH inverter • Defective IH coil unit • Defective fusing unit
585 IH coil unit full power (1250W) error
The IH coil unit full power (1250W) continues for 200 seconds or more ( copyir.com • Defective IH inverter • Defective BICU • Defective IOB • Broken connection between IH inverter and IOB • Defective thermopile
610 Mechanical counter error: K
This SC is only for NA models ( copyir.com The machine detects the mechanical counter error when SP5987-001 is set to “1” ( copyir.com • Disconnected mechanical counter • Defective mechanical counter
611 Mechanical counter error: FC
This SC is only for NA models ( copyir.com The machine detects the mechanical counter error when SP5987-001 is set to “1” ( copyir.com • Disconnected mechanical counter • Defective mechanical counter
620 ARDF communication error
After the ARDF is detected, the break signal occurs or communication timeout occurs ( copyir.com • Incorrect installation of ARDF • ARDF defective • BICU board defective • External noise
621 Finisher communication error
While the IOB communicates with an optional unit, an SC code is displayed if one of following conditions occurs ( copyir.com • The IOB receives the break signal which is generated by the peripherals only just after the main switch is turned on ( copyir.com • When the IOB does not receive an OK signal from a peripheral 100ms after sending a command to it ( copyir.com The IOB resends the command ( copyir.com The IOB does not receive an OK signal after sending the command 3 times ( copyir.com • Cable problems • IOB problems • BICU problems • PSU problems in the machine • Main board problems in the peripherals
622 Paper tray unit communication error
While the IOB communicates with an optional unit, an SC code is displayed if one of following conditions occurs ( copyir.com • The IOB receives the break signal which is generated by the peripherals only just after the main switch is turned on ( copyir.com • When the IOB does not receive an OK signal from a peripheral 100ms after sending a command to it ( copyir.com The IOB resends the command ( copyir.com The IOB does not receive an OK signal after sending the command 3 times ( copyir.com • Cable problems • IOB problems • BICU problems • PSU problems in the machine • Main board problems in the peripherals
623 2nd Paper Bank communication error
This SC is not issued for this machine ( copyir.com When a communication error signal between the 1st paper bank and 2nd paper bank is received ( copyir.com • Loose connector
632 Counter device error 1
After 3 attempts to send a data frame to the optional counter device via the serial communication line, no ACK signal was received within 100 ms ( copyir.com • Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged • Make sure that SP5113 is set to enable the optional counter device ( copyir.com
633 Counter device error 2
After 3 attempts to send a data frame to the optional counter device via the serial communication line, no ACK signal was received within 100 ms ( copyir.com • Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged • Make sure that SP5113 is set to enable the optional counter device ( copyir.com
634 Counter device error 3
A backup RAM error was returned by the counter device ( copyir.com • Counter device control board defective • Backup battery of counter device defective
635 Counter device error 4
A backup battery error was returned by the counter device ( copyir.com • Counter device control board defective • Backup battery of counter device defective
636 SD Card Error
641 BICU control data transfer abnormal
A sampling of the control data sent from the BICU reveals an abnormality ( copyir.com • Controller board defective • External noise • BICU board defective
650 Communication error of the remote service modem (Cumin-M)
651 Incorrect dial up connection
-001: Program parameter error -002: Program execution error An unexpected error occurs when the modem (Cumin-M) tries to call the center with a dial up connection ( copyir.com • Caused by a software bug
669 EEPROM error
Retry of EEPROM communication fails three times after the machine has detected the EEPROM error ( copyir.com • Caused by noise
670 Engine start up error
The ready signal from the engine board is not detected ( copyir.com • Defective engine board ( copyir.com
671 Engine board mismatch error
Engine board and controller mismatch detected ( copyir.com • Wrong engine board installed ( copyir.com • Wrong controller board installed ( copyir.com • Check the type of engine board and controller board ( copyir.com
672 Controller-to-operation panel communication error at startup
After powering on the machine, the communication circuit between the controller and the operation panel is not opened, or communication with controller is interrupted after a normal startup ( copyir.com • Controller stall • Controller board installed incorrectly • Controller board defective • Operation panel connector loose or defective
681 RFID: Communication error
• Communication error occurs when the RFID starts to communicate with the RFID receptor ( copyir.com • Retry of RFID communication fails three times after the machine has detected the RFID communication error ( copyir.com • Defective RFID reader and writer • Disconnected ASAP I/F • No memory chip on the toner cartridge • Noise
682 Memory chip at TD sensor: Communication error
Retry of memory chip communication fails three times after the machine has detected the memory chip communication error ( copyir.com • Damaged memory chip data • Disconnected inter face • No memory chip on the development unit • Noise
683 RFID: Unit check error
The machine gets RFID communication error even the toner cartridges have not been installed in the machine ( copyir.com Caused by noise
687 Memory address command error
The BICU does not receive a memory address command from the controller 120 seconds after paper is in the position for registration ( copyir.com • Loose connection • Defective controller • Defective BICU
690 GAVD communication error
• The I2C bus device ID is not identified during initialization ( copyir.com • A device-status error occurs during I2C bus communication ( copyir.com • The I2C bus communication is not established due to an error other than a buffer shortage ( copyir.com • Loose connection • Defective BICU • Defective LD controller board
700 Original stopper HP error
When the pick-up motor turns on clockwise, the original stopper HP sensor does not detect the home position of the original stopper ( copyir.com • Detached timing belt for the pick-up motor • Defective original stopper HP sensor • Defective pick-up motor • Defective DF drive board
701 Pick-up roller HP error
When the pick-up motor turns on counterclockwise, the pick-up roller HP sensor does not detect the home position of the pick-up roller ( copyir.com • Defective pick-up roller HP sensor • Defective pick-up motor • Defective DF drive board
705 ADF original table lift malfunction
One of the following conditions was detected ( copyir.com • The bottom plate position sensor does not activate when the bottom plate motor lifts the original table ( copyir.com • The bottom plate HP sensor does not activate when the bottom plate motor lowers the original table ( copyir.com • Loose, broken or defective harnesses, connectors of the bottom plate position sensor, bottom plate HP sensor, bottom plate motor • Defective bottom plate position sensor • Defective bottom plate HP sensor • Defective bottom plate motor • Defective ADF main control board
708 DF fan error
DF fan motor lock signal is detected after the original transportation has finished ( copyir.com Turn the machine off and on ( copyir.com
715-001 ADF pick-up motor driver error
The protection circuit of the motor driver stops the motor operation due to over current or high temperature ( copyir.com Turn the machine off and on ( copyir.com
715-002 ADF feed motor driver error
The protection circuit of the motor driver stops the motor operation due to over current, high temperature or driver open ( copyir.com Turn the machine off and on ( copyir.com
715-003 ADF transport motor driver error
The protection circuit of the motor driver stops the motor operation due to over current, high temperature or driver open ( copyir.com Turn the machine off and on ( copyir.com
715-004 ADF exit motor driver error (one-pass through model only)
The protection circuit of the motor driver stops the motor operation due to over current, high temperature or driver open ( copyir.com Turn the machine off and on ( copyir.com
715-006 ADF exit motor driver error (auto reverse model only)
The protection circuit of the motor driver stops the motor operation due to over current, high temperature or driver open ( copyir.com Turn the machine off and on ( copyir.com
721 Finisher jogger motor error
The jogger fences move out of the home position but the HP sensor output does not change within the specified number of pulses ( copyir.com The 1st failure issues an original jam message, and the 2nd failure issues this SC code ( copyir.com • Jogger HP sensor disconnected, defective • Jogger motor disconnected, defective • Jogger motor overloaded due to obstruction • Finisher main board and jogger motor
723 Stack feed-out motor error
• The stack feed-out HP sensor does not detect the home position of the stack feed-out belt 3000ms after the stack feed-out belt has moved to its home position ( copyir.com • The stack feed-out HP sensor does not turn off 200 ms after the stack feed-out belt has moved from its home position ( copyir.com • The 1st detection failure causes a jam error, and the 2nd failure causes this SC code ( copyir.com • Defective stack feed-out HP sensor • Overload on the stack feed-out motor • Defective stack feed-out motor • Defective main board • Disconnected or defective harness
725 Finisher exit guide plate motor error
After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time ( copyir.com The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defectiveon ( copyir.com
730 Finisher Tray 1 shift motor error
The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position ( copyir.com The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction
740 Finisher corner stapler motor error
The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com For the 2000/3000-sheet (booklet) finisher • Staple movement is not finished after a certain time ( copyir.com For the 1000-sheet finisher • The stapler motor does not switch off within the prescribed time after operating ( copyir.com • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position ( copyir.com • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position ( copyir.com • Staple jam • Motor overload • Defective stapler motor
742 Finisher stapler movement motor error
The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com For the 2000/3000-sheet (booklet) finisher • Staple movement is not finished for a certain time ( copyir.com For the 1000-sheet finisher • The stapler HP sensor is not activated within the specified time after the stapler motor turned on ( copyir.com (First detection: jam error, consecutive twice detection SC code) ( copyir.com • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor
743 Booklet stapler motor error 1
The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com For the 2000/3000-sheet (booklet) finisher The front stapler unit saddle-stitch motor does not start operation within the specified time ( copyir.com • Motor overload • Loose connection of the front stapler motor • Defective front stapler motor
744 Booklet staple motor error 2
The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com For the 2000/3000-sheet (booklet) finisher The rear stapler unit saddle-stitch motor does not start operation within the specified time ( copyir.com • Motor overload • Loose connection of the rear stapler motor • Defective rear stapler motor
750 1000/2000/3000-sheet (booklet) finisher: Tray lift motor error
The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers ( copyir.com • Motor overload • Loose connection of the shift tray motor • Defective shift tray motor
753 Stacking sponge roller motor
Occurs during the operation of the stacking sponge roller motor ( copyir.com • Disconnected, looser or defective motor harness • Motor overloaded • Disconnected, loose or defective sensor harness • Defective stacking sponge roller motor • Defective stacking roller HP sensor
760 Finisher punch motor error
The punch HP sensor is not activated within the specified time after the punch motor turned on ( copyir.com The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction
761 Finisher folder plate motor error
The folder plate moves but is not detected at the home position within the specified time ( copyir.com The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction
763 Punch movement motor error
The punch unit moves but is not detected at the home position within the specified time ( copyir.com The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com • Motor harness disconnected, loose, defective • Defective motor
764 Paper position sensor slide motor error
The paper position sensor moves but is not detected at the home position within the specified time ( copyir.com The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com • Motor harness disconnected, loose, defective • Defective motor
765 Fold unit bottom fence motor error
The bottom fence of the fold unit moves but is not detected at the home position within the specified time ( copyir.com The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com • Motor harness disconnected, loose, defective • Defective motor
766 Clamp roller retraction motor error
The clamp roller retraction motor moves but is not detected at the home position within the specified time ( copyir.com The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com • Motor harness disconnected, loose, defective • Defective motor
767 Stack junction gate motor error
The stack junction gate moves but is not detected at the home position within the specified time ( copyir.com The 1st detection failure issues a jam error, and the 2nd failure issues this SC code ( copyir.com • Motor harness disconnected, loose, defective • Defective motor
770 Shift motor error The shift motor HP sensor does not detect any change for 1 ( copyir.com 86 seconds after the shift motor has turned on at power on or during its operation ( copyir.com • Defective shift motor • Defective shift motor HP sensor
791 Bridge unit error
The machine recognizes the finisher, but does not recognize the bridge unit ( copyir.com • Defective connector • Broken harness
792 Finisher error
The machine does not recognize the finisher, but recognizes the bridge unit ( copyir.com • Defective connector • Defective harness • Incorrect installation
816 Energy saving I/O sub-system error
The energy saving I/O sub-system detects an error ( copyir.com • Controller board defective
819 Fatal kernel erro
Due to a control error, a RAM overflow occurred during system processing ( copyir.com One of the following messages was displayed on the operation panel ( copyir.com • System program defective • Controller board defective • Optional board defective
820 Self-diagnostics error: CPU [XXXX]: Detailed error code
833 Self-diagnostic error 8: Engine I/F ASIC
851 IEEE1394 interface error
The 1394 interface is unusable ( copyir.com • Defective IEEE1394 • Defective controller ( copyir.com
853 Wireless LAN card not detected
The wireless LAN card is not detected before communication is established, though the wireless LAN board is detected ( copyir.com • Loose connection
854 Wireless LAN/Bluetooth card not detected
The wireless LAN/Bluetooth card is not detected after communication is established, but the wireless LAN board is detected ( copyir.com • Loose connection
855, 856 Wireless LAN/Bluetooth card error
An error is detected in the wireless LAN/Bluetooth card ( copyir.com • Loose connection • Defective wireless LAN/Bluetooth card
857 USB interface error The USB interface cannot be used due to a driver error ( copyir.com • Defective USB driver • Loose connection
858 HDD Encryption unit error 1
A serious error occurs when data is encrypted to update an encryption key with the HDD encryption unit ( copyir.com
859 HDD Encryption unit error 2
A serious error occurs when the HDD data is encrypted to update an encryption key with the HDD encryption unit ( copyir.com
860 HDD: Initialization error
The controller detects that the hard disk fails ( copyir.com • HDD not initialized • Defective HDD
861 HDD: Reboot error
The HDD does not become ready within 30 seconds after the power is supplied to the HDD ( copyir.com • Loose connection • Defective cables • Defective HDD • Defective controller
863 HDD: Read error
The data stored in the HDD cannot be read correctly ( copyir.com • Defective HDD • Defective controller
864 HDD: CRC error
While reading data from the HDD or storing data in the HDD, data transmission fails ( copyir.com • Defective HDD
865 HDD: Access error
An error is detected while operating the HDD ( copyir.com • Defective HDD
866 SD card authentication error
A correct license is not found in the SD card ( copyir.com • SD-card data is corrupted ( copyir.com
867 SD card error
The SD card is ejected from the slot ( copyir.com 1 ( copyir.com Install the SD card ( copyir.com 2 ( copyir.com Turn the main switch off and on ( copyir.com
868 SD card access error
• -13 to -3: File system error • Other number: Device error An error report is sent from the SD card reader ( copyir.com • An error is detected in the SD card ( copyir.com
870 Address book error
An error is detected in the data copied to the address book over a network ( copyir.com • Defective software program • Defective HDD • Incorrect path to the server
872 HDD mail data error
An error is detected in the HDD at machine initialization ( copyir.com • Defective HDD • Power failure during an access to the HDD
873 HDD mail transfer error An error is detected in the HDD at machine initialization ( copyir.com • Defective HDD • Power failure during an access to the HDD
874 Delete All error 1: HDD
An error is detected while all of the HDD or NVRAM are formatted physically by the Data Overwrite Security Unit (D377) ( copyir.com • Data Overwrite Security Unit (SD card) not installed • Defective HDD
875 Delete All error 2: Data area
An error is detected while all of the HDD or NVRAM are formatted logically by the Data Overwrite Security Unit (D377) ( copyir.com • The logical format for the HDD fails ( copyir.com
876 Log Data Error
An error was detected in the handling of the log data at power on or during machine operation ( copyir.com This can be caused by switching the machine off while it is operating ( copyir.com
877 HDD Data Overwrite Security SD card error
The ‘all delete’ function cannot be executed but the Data Overwrite Security Unit (D377) is installed and activated ( copyir.com • Defective SD card (D377) • SD card (D377) not installed
878 TPM system authentication error
The system firmware is not authenticated by TPM (security chip) ( copyir.com • Incorrect updating for the system firmware • Defective flash ROM on the controller board
880 File format converter error
The file format converter does not respond ( copyir.com • Defective file format converter
900 Electric counter error
Abnormal data in the counters ( copyir.com • Defective NVRAM • Defective controller
910 ( copyir.com ( copyir.com ( copyir.com 914 External Controller Error
919 External Controller Error 6
While EAC (External Application Converter), the conversion module, was operating normally, the receipt of a power line interrupt signal from the FLUTE serial driver was detected, or BREAK signal from the other station was detected ( copyir.com • Power outage at the EFI controller • EFI controller was rebooted • Connection to EFI controller loose
920 Printer application error
An error is detected in the printer application program ( copyir.com • Defective software • Unexpected hardware resource (e ( copyir.com g ( copyir.com , memory shortage)
921 Printer font error
A necessary font is not found in the SD card ( copyir.com • A necessary font is not found in the SD card ( copyir.com • The SD card data is corrupted ( copyir.com
990 Software performance error
The software makes an unexpected operation ( copyir.com • Defective software • Defective controller • Software error
991 Software continuity error
The software has attempted to perform an unexpected operation ( copyir.com However, unlike SC 990, the object of the error is continuity of the software ( copyir.com • Software program error • Internal parameter incorrect, insufficient working memory ( copyir.com
992 Undefined error
Defective software program • An error undetectable by any other SC code occurred
994 Operation panel management records exceeded
An error occurred because the number of records exceeded the limit for images managed in the service layer of the firmware ( copyir.com This can occur if there if there are too many application screens open on the operation panel ( copyir.com • No action required because this SC does not interfere with operation of the machine
995 CPM setting error
997 Application function selection error
• The application selected by the operation panel key does not start or ends abnormally ( copyir.com • Software (including the software configuration) defective • An option required by the application (RAM, DIMM, board) is not installed • Nesting of the fax group addresses is too complicated
998 Application start error
No applications start within 60 seconds after the power is turned on ( copyir.com • Loose connection of RAM-DIMM, ROM-DIMM • Defective controller • Software problem
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.