ریکو آفشیو Ricoh Aficio SPC400DN

ریکو آفشیو Ricoh Aficio SPC400DN

ایرادات دستگاههای ریکو براساس کد می باشد. شرکت کپی ایران در نظر دارد تمامی سرویس مانوئلها و رفع ایرادات را در اختیار شما عزیزان قرار دهد.

195    Incorrect serial number
When checking the registered product number, it does not match the printer’s product number ( copyir.com     Registered product number does not match the printer’s product number ( copyir.com
202    Polygon motor error: Time out with the polygon motor activated
After the polygon motor turns on or changes the speed, SCRDY_N is not active within 10 seconds ( copyir.com     Disconnected cable from the polygon motor drive board or defective connection ( copyir.com  Defective polygon motor or drive board
203    Polygon motor error: Time out with the polygon motor inactivated
After the polygon motor turns off or changes the speed, SCRDY_N is not inactive within 10 seconds ( copyir.com     Disconnected cable from the polygon motor drive board or defective connection ( copyir.com  Defective polygon motor or drive board
204    Polygon motor error: XSCRDY signal error
PMRDY_N signal consecutively detects that the polygon motor is an inactive state while LDB unit scans ( copyir.com     Disconnected cable from the polygon motor drive board or defective connection ( copyir.com  Defective polygon motor or drive board
205    Polygon motor error: XSCRDY signal not stable
PMRDY_N signal consecutively detects that the polygon motor is an inactive state while the polygon motor turns on or changes the speed ( copyir.com     Disconnected cable from the polygon motor drive board or defective connection ( copyir.com  Defective polygon motor or drive board ( copyir.com
210    Trailing edge laser detection error: [K]
The laser synchronizing detection signal for LDB [K] of the trailing edge is not detected for one second after the LDB unit turned on when detecting the main scan magnification ( copyir.com     Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com  Defective laser synchronizing detector Defective LDB Defective EGB
211    Trailing edge laser detection error: [Y]
The laser synchronizing detection signal for LDB [Y] of the trailing edge is not detected for one second after the LDB unit turned on when detecting the main scan magnification ( copyir.com     Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com  Defective laser synchronizing detector Defective LDB Defective EGB
212    Trailing edge laser detection error: [M]
The laser synchronizing detection signal for LDB [M] of the trailing edge is not detected for one second after the LDB unit turned on when detecting the main scan magnification ( copyir.com     Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com  Defective laser synchronizing detector Defective LDB Defective EGB
213    Trailing edge laser detection error: [C]
The laser synchronizing detection signal for LDB [C] of the trailing edge is not detected for one second after the LDB unit turned on when detecting the main scan magnification ( copyir.com     Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com  Defective laser synchronizing detector Defective LDB Defective EGB
220    Laser Synchronizing Detection Error: LDB of the leading edge [K]
The laser synchronizing detection signal for LDB [K] of the leading edge is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com tion ( copyir.com     Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com  Defective laser synchronizing detector ( copyir.com  Defective LDB ( copyir.com  Defective EGB ( copyir.com
222    Leading edge laser detection error: [Y]
The laser synchronizing detection signal for LDB [Y] of the leading edge is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com     Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com  Defective laser synchronizing detector ( copyir.com  Defective LDB ( copyir.com  Defective EGB
224    Leading edge laser detection error: [M]
The laser synchronizing detection signal for LDB [M] of the leading edge is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally ( copyir.com     Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com  Defective laser synchronizing detector ( copyir.com  Defective LDB ( copyir.com  Defective EGB
226    Leading edge laser detection error: [C]
The laser synchronizing detection signal for LDB [C] of the leading edge is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally    Disconnected cable from the laser synchronizing detection unit or defective connection ( copyir.com  Defective laser synchronizing detector ( copyir.com  Defective LDB ( copyir.com  Defective EGB
230    FGATE: On error [K]
The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for [K] starts ( copyir.com     Defective connection between the controller board and EGB ( copyir.com  Defective cable between the EGB and LDB ( copyir.com
231    FGATE: Off error [K]
The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for [K] ends ( copyir.com  The PFGATE ON signal still asserts when the next job starts ( copyir.com     Defective connection between the controller board and EGB ( copyir.com  Defective cable between the EGB and LDB ( copyir.com
232    FGATE: On error [Y]
The PFGATE register of GAVD does not assert within 5 seconds after processing the image in normal job or MUSIC for [Y] started    Defective connection between the controller board and EGB ( copyir.com  Defective cable between the EGB and LDB ( copyir.com
233    FGATE: Off error [Y]
The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for [K] ends ( copyir.com  The PFGATE ON signal still asserts when the next job starts ( copyir.com     Defective connection between the controller board and EGB ( copyir.com  Defective cable between the EGB and LDB ( copyir.com
234    FGATE: On error [M]
The PFGATE register of GAVD does not assert within 5 seconds after processing the image in normal job or MUSIC for [M] started ( copyir.com     Defective connection between the controller board and EGB ( copyir.com  Defective cable between the EGB and LDB ( copyir.com
235    FGATE: Off error [M]
The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for [M] ends ( copyir.com  The PFGATE ON signal still asserts when the next job starts ( copyir.com     Defective connection between the controller board and EGB ( copyir.com  Defective cable between the EGB and LDB ( copyir.com
236    FGATE: On error [C]
The PFGATE register of GAVD does not assert within 5 seconds after processing the image in normal job or MUSIC for [C] started ( copyir.com     Defective connection between the controller board and EGB ( copyir.com  Defective cable between the EGB and LDB ( copyir.com
237    FGATE: Off error [C]
The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for [C] ends ( copyir.com   ( copyir.com  ( copyir.com  The PFGATE ON signal still asserts when the next job starts ( copyir.com     Defective connection between the controller board and EGB ( copyir.com  Defective cable between the EGB and LDB ( copyir.com
240    LDB error [K]
The EGB detects LDB error an the few times consecutively when LDB unit turns on after LDB initialization ( copyir.com     Defective LDB
241    LDB error [Y]
The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization    Defective LDB
242    LDB error [M]
The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization    Defective LDB
243    LDB error [C]
The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization ( copyir.com     Defective LDB
270    LDU shutter error
Sensor output does not change even if 1 second passes after the LDU shutter motor is on ( copyir.com     Sensor defective or LDU shutter motor defective
300    High voltage power board: Charge voltage output error [K]
The measured voltage is not proper when EGB measures the charge output for each color ( copyir.com     Defective charge roller ( copyir.com  Defective connectors ( copyir.com  Disconnected harness ( copyir.com  Defective high voltage power 1 ( copyir.com
301    High voltage power board: Charge voltage output error [M]
The measured voltage is not proper when EGB measures the charge output for each color ( copyir.com     Defective charge roller ( copyir.com  Defective connectors ( copyir.com  Disconnected harness ( copyir.com  Defective high voltage power 1 ( copyir.com
302    High voltage power board: Charge voltage output error [C]
The measured voltage is not proper when EGB measures the charge output for each color ( copyir.com     Defective charge roller ( copyir.com  Defective connectors ( copyir.com  Disconnected harness ( copyir.com  Defective high voltage power 1 ( copyir.com
303    High voltage power board: Charge voltage output error [Y]
The measured voltage is not proper when EGB measures the charge output for each color ( copyir.com     Defective charge roller Defective connectors Disconnected harness Defective high voltage power 1
304    Charge AC bias error [K]
The charge current less than 200 mkA is detected ( copyir.com     Defective charge roller ( copyir.com  Defective connectors ( copyir.com  Disconnected harness ( copyir.com  Defective high voltage power 1 ( copyir.com
305    Charge AC bias error [M]
The charge current less than 200 mkA is detected ( copyir.com     Defective charge roller ( copyir.com  Defective connectors ( copyir.com  Disconnected harness ( copyir.com  Defective high voltage power 1 ( copyir.com
306    Charge AC bias error [C]
The charge current less than 200 mkA is detected ( copyir.com     Defective charge roller ( copyir.com  Defective connectors ( copyir.com  Disconnected harness ( copyir.com  Defective high voltage power 1 ( copyir.com
307    Charge AC bias error [Y]
The charge current less than 200 mkA is detected ( copyir.com     Defective charge roller ( copyir.com  Defective connectors ( copyir.com  Disconnected harness ( copyir.com  Defective high voltage power 1 ( copyir.com
325    Color development motor error
LOCK signal is not detected for more than two seconds while the motor START signal is on ( copyir.com  LOCK signal is not cancelled within two seconds after the motor is off ( copyir.com     Color development motor slip due to the increase of the load torque
360    TD sensor: Output maximum error [K]
Vt is more than the maximum value (4 ( copyir.com 5) for three times consecutively ( copyir.com     Defective connector connection ( copyir.com  Increasing toner density ( copyir.com
361    TD sensor: Output maximum error [M]
Vt is more than the maximum value (4 ( copyir.com 5) for three times consecutively ( copyir.com     Defective connector connection ( copyir.com  Increasing toner density ( copyir.com
362    TD sensor: Output maximum error [C]
Vt is more than the maximum value (4 ( copyir.com 5) for three times consecutively ( copyir.com     Defective connector connection ( copyir.com  Increasing toner density ( copyir.com
363    TD sensor: Output maximum error [Y]
Vt is more than the maximum value (4 ( copyir.com 5) for three times consecutively ( copyir.com     Defective connector connection ( copyir.com  Increasing toner density ( copyir.com
364    TD sensor: Output minimum error [K]
Vt is less than the minimum value (0 ( copyir.com 5) for three times consecutively ( copyir.com     Defective connector connection ( copyir.com  Decreasing toner density
365    TD sensor Output minimum error [M]
Vt is less than the minimum value (0 ( copyir.com 5) for three times consecutively ( copyir.com     Defective connector connection ( copyir.com  Decreasing toner density
366    TD sensor: Output minimum error [C]
Vt is less than the minimum value (0 ( copyir.com 5) for three times consecutively ( copyir.com     Defective connector connection ( copyir.com  Decreasing toner density
367    TD sensor: Output minimum error [Y]
Vt is less than the minimum value (0 ( copyir.com 5) for three times consecutively ( copyir.com     Defective connector connection ( copyir.com  Decreasing toner density
368    TD sensor: Initial control voltage error [K]
Vt is less than 1 V even though the control power voltage is adjusted to the maximum ( copyir.com  Vt is more than 1 V even though the control power voltage is adjusted to the minimum ( copyir.com     Defective connector connection ( copyir.com  Defective TD sensor ( copyir.com  The toner density in the developer is different ( copyir.com
369    TD sensor: Initial control voltage error [M]
Vt is less than 1 V even though the control power voltage is adjusted to the maximum ( copyir.com  Vt is more than 1 V even though the control power voltage is adjusted to the minimum ( copyir.com     Defective connector connection ( copyir.com  Defective TD sensor ( copyir.com  The toner density in the developer is different ( copyir.com
370    TD sensor: Initial control voltage error [C]
Vt is less than 1 V even though the control power voltage is adjusted to the maximum ( copyir.com  Vt is more than 1 V even though the control power voltage is adjusted to the minimum ( copyir.com     Defective connector connection ( copyir.com  Defective TD sensor ( copyir.com  The toner density in the developer is different ( copyir.com
371    TD sensor: Initial control voltage error [Y]
Vt is less than 1 V even though the control power voltage is adjusted to the maximum ( copyir.com  Vt is more than 1 V even though the control power voltage is adjusted to the minimum ( copyir.com     Defective connector connection ( copyir.com  Defective TD sensor ( copyir.com  The toner density in the developer is different ( copyir.com
372    TD sensor: Initial adjustment error [K]
Vt is not (A +-0 ( copyir.com 2) when initial setting for TD sensor is executed ( copyir.com  A = SP3011-001 for [K]    Defective connector connection ( copyir.com  Defective TD sensor ( copyir.com  The toner density in the developer is different from the initial condition ( copyir.com
373    TD sensor: Initial adjustment error [M]
Vt is not (A +-0 ( copyir.com 2) when initial setting for TD sensor is executed ( copyir.com  A = SP 3011 2 for [M]    Defective connector connection ( copyir.com  Defective TD sensor ( copyir.com  The toner density in the developer is different from the initial condition ( copyir.com
374    TD sensor: Initial adjustment error [C]
Vt is not (A +-0 ( copyir.com 2) when initial setting for TD sensor is executed ( copyir.com  A = SP 3011 3 for [C]    Defective connector connection ( copyir.com  Defective TD sensor ( copyir.com  The toner density in the developer is different from the initial condition ( copyir.com
375    TD sensor: Initial adjustment error [Y]
Vt is not (A ±0 ( copyir.com 2) when initial setting for TD sensor is executed ( copyir.com  A = SP 3011 4 for [Y]    Defective connector connection ( copyir.com  Defective TD sensor ( copyir.com  The toner density in the developer is different from the initial condition ( copyir.com
380    Drum gear position sensor error
When receiving the input signal of drum gear position sensor is not correctly done, SC380 is logged ( copyir.com     Dirty or defective drum gear position sensor
396    Drum motor error [K]
The LOCK signal is not detected for 2 seconds more while the start signal of the drum motor for black PCU is output ( copyir.com     OPC motor slip due to the excessive load
397    Drum motor error [CMY]
The LOCK signal is not detected for 2 seconds more while the start signal of the drum motor for color PCU is output ( copyir.com     OPC motor slip due to the excessive load
400    ID sensor correction error
Regular Vsp is not (4 ±0 ( copyir.com 5V) when ID sensor correction is executed ( copyir.com     Defective ID sensors ( copyir.com  Dirty ID sensors or transfer belt ( copyir.com  ID sensor life is over ( copyir.com
418    ID sensor: LED adjustment error
LED PWM adjustment is not [A] for three times consecutively ( copyir.com  [A] = 50 < [A] < 400    Defective ID sensors ( copyir.com  Dirty ID sensors or transfer belt ( copyir.com  ID sensor life is over ( copyir.com
442    Transfer belt contact error
The transfer belt contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates ( copyir.com     Dirty transfer belt contact sensor ( copyir.com  Defective transfer belt contact motor ( copyir.com  Disconnected connector of transfer belt contact sensor or motor ( copyir.com  Disconnected cable ( copyir.com
452    Transfer roller contact error
The transfer roller contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates ( copyir.com     Defective transfer roller contact sensor ( copyir.com  Defective transfer roller contact motor ( copyir.com  Defective IOB
490    High Voltage Power 1: High voltage output error
Error signal is detected for 10 times consecutively    One of the DC bias outputs for each PCU is shorted or one of the transfer belt bias outputs for [Y], [M] and [C] ( copyir.com  Power leaking ( copyir.com  Defective connection ( copyir.com  Disconnected cable ( copyir.com  Defective PCU ( copyir.com  Defective High Voltage Power 1 ( copyir.com
491    High Voltage Power 2: High voltage output error
Error signal is detected for 10 times consecutively ( copyir.com     One of the separation bias output, development bias output and transfer belt cleaning bias output is shorted or one of the transfer belt bias output for [K] and transfer roller bias output is shorted ( copyir.com  Power leaking ( copyir.com  Defective connection ( copyir.com  Defective PCU ( copyir.com  Defective High Voltage Power 2 ( copyir.com
531    Paper feed / Fusing motor error
LOCK signal is not detected for more than two seconds while the motor START signal is on ( copyir.com  LOCK signal is not cancelled within two seconds after the motor is off ( copyir.com     Defective paper feed/ fusing motor
532    Fan motor error
The fan motor “On” signal is not detected for the components below after the drum motor for black is set to “On” ( copyir.com  PSU fan ( copyir.com  Fusing unit fan ( copyir.com  Polygon motor fan ( copyir.com  Drive unit fan ( copyir.com  Exit paper fanoltage ( copyir.com     Defective fan motor
541    Thermistor error
The thermistor output is less than 0 °C for six seconds ( copyir.com     Disconnected thermistor ( copyir.com  Defective connector connection ( copyir.com
542    Print ready temperature error
The heating roller temperature increase that is less than 67 degrees for 9 seconds is detected five times consecutively ( copyir.com  The fusing temperature does not reach the print ready temperature within 15 seconds after the fusing lamp was controlled ( copyir.com     Defective thermistor ( copyir.com  Thermistor coming off ( copyir.com  Incorrect power supply input at the main power socket ( copyir.com  Defective fusing lamp ( copyir.com
543    High temperature detection: Software
The thermistor detects 230°C for 0 ( copyir.com 2 seconds ( copyir.com     Defective thermistor ( copyir.com  Defective I/O board ( copyir.com  Defective EGB ( copyir.com
544    High temperature detection: Hard
The thermistor detects 250°C ( copyir.com     Defective thermistor ( copyir.com  Defective I/O board ( copyir.com  Defective EGB ( copyir.com  Defective fusing unit, PSU, or EGB ( copyir.com
545    Heating lamp error
The fusing lamp is full-powered for 8 seconds after the heating roller reaches the print ready temperature ( copyir.com     Deformed thermistor ( copyir.com  Thermistor coming off ( copyir.com  Defective fusing lamp ( copyir.com
547    Zero cross error
The zero cross signal is detected three times even though the heater relay is off when turning on the main power ( copyir.com  The zero cross signal is not detected for three seconds even though the heater relay is on after turning on the main power or closing the front door ( copyir.com  The detection error occurs twice or more in the ten zero cross signal detections ( copyir.com  This error is defined when the detected zero cross signal is less than 17 for 200 ms ( copyir.com     Defective fusing lamp relay ( copyir.com  Defective fusing lamp relay circuit ( copyir.com  Unstable power supply ( copyir.com
557    Zero cross frequency error
The detection error occurs ten times in a row in ten zero cross signal detections ( copyir.com  This error is defined when the detected zero cross signal is more than 28 for 200 ms ( copyir.com  This SC is only logged ( copyir.com  In this case, the power frequency is defined as 60 Hz ( copyir.com     Noise (high frequency)
559    Continuous paper jam at Fusing unit
The paper jam occurs three times consecutively at the fusing unit only when the SP 1159 1 is set to “1 (ON)” ( copyir.com  If not, this SP does not occur ( copyir.com  The jam counter is cleared when a sheet of paper is fed normally ( copyir.com     Defective fusing entrance sensor ( copyir.com  Defective EGB ( copyir.com
636    SD Card Error
670    Engine start-up error
A command from the controller board is not received ( copyir.com     Defective engine board
687    Controller board command error
A command from the controller board is not received ( copyir.com     Loose connection ( copyir.com  Defective controller board ( copyir.com  Defective EGB ( copyir.com
690    EGB data error
The data transfer in the EGB is interrupted by some incident (e ( copyir.com g ( copyir.com  cover open etc ( copyir.com ) during the data transfer ( copyir.com     Defective EGB
818    Watchdog error
While the system program is running, no other programs can run (due to a bus hold or endless loop) ( copyir.com     Defective system program ( copyir.com  Defective controller board ( copyir.com
819    Kernel stop
821    Self-Diagnostic Error: ASIC
822    Self-Diagnostic Error: HDD
823    Self-diagnostic Error: NIB
824    Self-diagnostic Error: NVRAM
826    Self-diagnostic Error: RTC/Optional NVRAM
827    Self-diagnostic Error: RAM
828    Self-diagnostic Error: ROM
829    Self-diagnostic Error: Optional RAM
853    Wireless LAN or Bluetooth card not detected at starting communication
The wireless LAN or Bluetooth card is not detected before communication is established, though the wireless LAN or Bluetooth board is detected ( copyir.com     Loose connection
854    Wireless LAN or Bluetooth card not detected during operation
The wireless LAN or Bluetooth card is not detected after communication is established, though the wireless LAN or Bluetooth board is detected ( copyir.com     Loose connection
855    Wireless LAN or Bluetooth card error
An error is detected in the wireless LAN or Bluetooth card ( copyir.com     Loose connection ( copyir.com  Defective wireless LAN or Bluetooth card ( copyir.com
856    Wireless LAN or Bluetooth board error
An error is detected in the wireless LAN or Bluetooth board ( copyir.com     Defective wireless LAN or Bluetooth board ( copyir.com  Loose connection
857    USB interface error
The USB interface cannot be used due to a driver error ( copyir.com     Defective USB driver ( copyir.com  Loose connection
860    HDD: Initialization error
The controller detects that the hard disk fails ( copyir.com     HDD not initialized ( copyir.com  Defective HDD ( copyir.com
861    HDD: Reboot error
The HDD does not become ready within 30 seconds after the power is supplied to the HDD ( copyir.com     Loose connection ( copyir.com  Defective cables ( copyir.com  Defective HDD ( copyir.com  Defective controller ( copyir.com
863    HDD: Read error
The data stored in the HDD cannot be read correctly ( copyir.com     Defective HDD ( copyir.com  Defective controller ( copyir.com
864    HDD: CRC error
While reading data from the HDD or storing data in the HDD, data transmission fails ( copyir.com     Defective HDD
865    HDD: Access error
An error other than SC863 and SC864 is detected while operating the HDD ( copyir.com     Defective HDD
866    SD card authentication error
A correct license is not found in the SD card ( copyir.com     SD-card data is corrupted ( copyir.com
867    SD card error
The SD card for an application is ejected from the slot ( copyir.com     The SD card for an application is ejected from the slot ( copyir.com
868    SD card access error [File system error, Device error]
SD card error occurs when SD card is activated ( copyir.com     Defective SD card ( copyir.com  Defective SD card controller ( copyir.com
870    Address data error
An error is detected in theve SD data copied to the address book over a network ( copyir.com     Defective software program ( copyir.com  Defective HDD ( copyir.com  Incorrect path to the sever ( copyir.com
872    HDD mail data error
An error is detected in the mail receiving data area of the HDD at machine initialization ( copyir.com     Defective HDD ( copyir.com  Power failure during an access to the HDD ( copyir.com
873    HDD mail transfer error
An error is detected in the mail transmitting data area of the HDD at machine initialization ( copyir.com     Defective HDD ( copyir.com  Power failure during an access to the HDD ( copyir.com
874    Delete All error 1: HDD
An error is detected while the all data of the HDD or NVRAM are formatted physically by the Data Overwrite Security Unit (B735) ( copyir.com     Not installed Data Overwrite Security Unit (SD card) ( copyir.com  Defective HDD ( copyir.com
875    Delete All error 2: Data area
An error is detected while the all data of the HDD or NVRAM are formatted logically by the Data Overwrite Security Unit (B735) ( copyir.com     The logical format for HDD fails ( copyir.com
876    Log Data Error
877    HDD Data Overwrite Security SD card error
The all delete cannot be executed even though the Data Overwrite Security Unit (B735) is installed and activated ( copyir.com     Defective SD card (B735) ( copyir.com  Not installed SD card (B735) ( copyir.com
900    Electric counter error
Abnormal data is stored in the counters ( copyir.com     Defective NVRAM ( copyir.com  Defective controller ( copyir.com
920    Printer function error
The error that causes the malfunction in the software application is detected ( copyir.com     Turn the main switch off/on, or install Printer Application firmware ( copyir.com  Unexpected hardware structure (insufficient memory or hard disk space ( copyir.com )
921    Printer font error
No font is detected in the machines that have the font in the SD card when the printer application is run ( copyir.com     Install the System, Printer Application, NIB, and Web System firmware ( copyir.com
990    Software performance error 1
The software makes an unexpected operation ( copyir.com     Defective software ( copyir.com  Defective controller ( copyir.com  Software error ( copyir.com
991    Software performance error 2
Unexpected software error detected, which does not affect operation of the machine    The machine does not stop and the SC code is not displayed ( copyir.com  The machine automatically recovers ( copyir.com  However, the SC code is logged in the engine summary sheet (SMC) ( copyir.com
992    SC not defined
SC that is not controlled in the system occurs    Defective system software
998    Application start error
No applications start within 60 seconds after the power is turned on ( copyir.com     Loose connection of RAM, DIMM and SD card in slot 1 ( copyir.com  Defective controller ( copyir.com  Software problem ( copyir.com