لمینت MKP
1402-06-04
Menu
E1-00 IMC PWB communication trouble
An abnormality occurs in communication between the MCU PWB and the IMC PWB copyir.com IMC PWB-MCU PWB harness abnormality MCU PWB connector disconnection IMC PWB ROM defect/data abnormality
E1-10 IMC PWB trouble
An abnormality occurs in the IMC PWB copyir.com USB chip error/CODEC error on the IMC PWB
E1-11 IMC ASIC error
An abnormality occurs in the IMC PWB copyir.com Abnormality in ASIC on the IMC PWB
E1-13 IMC PWB flash ROM error
An abnormality occurs in the IMC flash ROM copyir.com IMC PWB abnormality
E1-16 IMC PWB DIMM memory read/write check error
An installation error occurs in the IMC expansion compression memory module copyir.com An error occurs during access to the IMC expansion compression memory copyir.com Improper installation of the IMC expansion memory module copyir.com IMC expansion memory module abnormality IMC expansion memory contact abnormality IMC PWB abnormality copyir.com
E1-81 Interface error (Parityفتوکپی in communication with the IMC PWB
A parity error occurs in communication between the MCU PWB and the IMC PWB copyir.com IMC PWB-MCU PWB harness defect Improper connection of the MCU PWB connector IMC PWB ROM defect/data abnormality”
E1-82 Interface error (Overrunفتوکپی in communication with the IMC PWB
An overrun error occurs in communication between the MCU PWB and the IMC PWB copyir.com IMC PWB-MCU PWB harness defect Improper connection of the MCU PWB connector IMC PWB ROM defect/data abnormality copyir.com
E1-84 Interface error (Framingفتوکپی in communication with the IMC PWB
A framing error occurs in communication between the MCU PWB and the IMC PWB copyir.com IMC PWB-MCU PWB harness defect Improper connection of the MCU PWB connector IMC PWB ROM defect/data abnormality copyir.com
E7-01 Duplex model memory error
The memory capacity for the duplex model machine is improper copyir.com Insufficient memory capacity The memory capacity of the MCU PWB is improper copyir.com
E7-02 LSU trouble
The BD signal from the LSU cannot be detected in a certain cycle copyir.com (Always OFF or always ONفتوکپی LSU connector or LSU harness defect or disconnection Polygon motor rotation abnormality Laser beams are not generated copyir.com MCU PWB abnormality copyir.com
E7-10 Shading trouble (Black correctionفتوکپی
The CCD black scan level is abnormal when the shading copyir.com Improper connection of the CCD unit flat cable CCD unit abnormality MCU PWB abnormality copyir.com
E7-11 Shading trouble (White correctionفتوکپی
The CCD white scan level is abnormal when the shading copyir.com Improper connection of the CCD unit flat cable Dirt on the mirror, the lens, and the reference white plate Copy lamp lighting abnormality CCD unit abnormality MCU PWB abnormality (When occurred in the SPF scan position copyir.comفتوکپی Improper installation of the mirror unit
E7-12 Shading trouble
White correction is not completed in the specified number of operations copyir.com CCD unit flat cable connection failure copyir.com Dirt on mirrors, lenses, and the reference white plate copyir.com Copy lamp lighting abnormality CCD unit abnormality MCU PWB abnormality
E7-16 Abnormal laser output
When the laser output is stopped, HSYNC is detected copyir.com Laser abnormality MCU PWB abnormality copyir.com
F2-04 Improper cartridge (Destination error, life cycle errorفتوکپی
The destination of the machine differs from that of the CRUM copyir.com The life cycle information is other than “Not used (FFhفتوکپی copyir.com” CRUM chip defect Improper developing unit
F5-02 Copy lamp lighting abnormality
The copy lamp does not turn on copyir.com Copy lamp abnormality Copy lamp harness abnormality CCD PWB harness abnormality copyir.com
H2-00 Thermistor open
The thermistor is open copyir.com The fusing unit is not installed copyir.com Thermistor abnormality Control PWB abnormality Fusing section connector disconnection The fusing unit is not installed copyir.com
H3-00 Heat roller high temperature detection
The fusing temperature exceeds 240C° copyir.com Thermistor abnormality Control PWB abnormality Fusing section connector disconnection copyir.com
H4-00 Heat roller low temperature detection
When the fusing temperature is lower than 150C° after 55sec from the start of warming up copyir.com When the warming up complete temperature is not reached in 30sec from reaching 150C° copyir.com When the fusing temperature is lower than 100C° after 20sec from ready start copyir.com When the fusing temperature is lower than 145C° when printing copyir.com” Thermistor abnormality Heater lamp abnormality Thermostat abnormality Control PWB abnormality
L1-00 Scanner feed trouble
The scanner does not complete feeding in the specified time copyir.com Mirror unit abnormality The scanner wire is disconnected copyir.com The origin detection sensor abnormality Mirror motor harness abnormality
L3-00 Scanner return trouble
The scanner does not complete returning in the specified time copyir.com The mirror is not in the home position when OC copying is started with the mirror standby in the home position copyir.com Mirror unit abnormality Scanner wire disconnection Origin detection sensor abnormality Mirror motor harness abnormality
L4-01 Main motor lock detection
The main motor does not rotate copyir.com The motor lock signal is detected for 1sec or more after rotation of the main motor copyir.com The motor lock signal is detected for 1sec during rotation of the main motor copyir.com Main motor unit abnormality Improper connection or disconnection the main motor and the harness copyir.com MCU PWB abnormality
L4-11 Shifter motor trouble
The shifter home position detection signal is not detected when initializing the shifter copyir.com Shifter motor abnormality, improper connection or disconnection of the harness, shifter home position sensor abnormality
L6-10 Polygon motor lock detection
The polygon motor does not rotate copyir.com The motor lock signal is detected for 6sec after rotation of the polygon motor copyir.com The motor lock signal is detected for 1sec during rotation of the polygon motor copyir.com Polygon motor unit abnormality Improper connection or disconnection of the polygon motor and the harness copyir.com MCU PWB abnormality
L8-01 No full wave signal
The zero cross signal is not detected copyir.com Power unit abnormality MCU PWB abnormality
U2-04 EEPROM read/write error (Serial communication errorفتوکپی
EEPROM access process error EEPROM abnormality
U2-11 Counter check sum error (EEPROMفتوکپی
Check sum error of the counter area in the EEPROM EEPROM abnormality
U2-12 Adjustment value check sum error (EEPROMفتوکپی
Check sum error of the adjustment value area in the EEPROM EEPROM abnormality
U2-40 CRUM chip communication error
An error occurs during communication between the MCU and the CRUM chip copyir.com CRUM chip abnormality Developing unit disconnection MCU PWB abnormality
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.