توشیبا استودیو Toshiba e-Studio 170F
10 A paper jam has occurred within the paper feed section of the recording paper tray copyir.com
10 There was no recording paper or the recording paper tray was not installed during the reception copyir.com
11 A recording paper jam occurred during the reception copyir.com
12 A document jam occurred copyir.com
13 During the transmission, the RX cover or front cover was opened and the transmission stopped copyir.com
20 A paper jam has occurred within the paper feed section of the optional recording paper tray copyir.com
20 A power failure occurred during the transmission or reception, and the transmission/reception document data was lost copyir.com
22 A file error occurred due to a directory error copyir.com
22 copyir.com copyir.com copyir.com 24 The fuser failed to operate normally copyir.com
30 The [STOP] key was pressed during the communication, and the communication was stopped copyir.com
32 The set number of document pages did not match the actual pages transmitted copyir.com
33 The polling password did not match, or no polling document existed copyir.com
41 The polygon motor in the LSU failed to operate copyir.com
42 The laser beam was not controlled correctly copyir.com
42 During a memory transmission or a memory reception, the machine ran out of image memory copyir.com The machine’s image memory was exhausted copyir.com
43 The HVPS failed to operate normally copyir.com
50 Dialing and redialing was attempted as many as the specified count but the line was busy copyir.com
51 The FAN motor failed to operate normally copyir.com
53 The password did not match in a relay or mailbox transmission, and the transmission ended in failure copyir.com
60 Communication error between the main-CPU (IC22) and the engine-CPU (IC37) copyir.com
80 The DSC (IC59) failed to operate normally copyir.com
80 A paper jam has occurred within the drum/developer section of the paper transport path copyir.com
81 The RTC (IC23) failed to operate normally copyir.com
82 The MODEM (IC5) for Line-1 failed to operate normally copyir.com
87 There was no residual memory in the remote party’s fax unit during a relay/mailbox transmission copyir.com
90 A paper jam has occurred within the paper exit section of the paper transport path copyir.com
B0 DIS (GI) could not detected copyir.com
B1 DIS/NSF that cannot be handled by the sender is received copyir.com
The receiver received NSS/DCS other than those declared by DIS/NSF copyir.com
B2 DCN is received copyir.com
B3 DCS/DTC was not detected copyir.com
B4 The sender performed fall-back but the transmission was not enabled copyir.com The receiver performed time-out after sending FTT copyir.com Or DCN is received copyir.com
B5 CFR (FTT) was not detected copyir.com
C0 Image signal carrier was not detected copyir.com
C1 High-speed signal was not detected on the receiving side copyir.com
C2 After detecting the image signal, carrier off was detected for more than 1 second copyir.com
C3 After detecting a high-speed signal, EOL was not detected for 15 seconds copyir.com
C4 The EOL timer has timed out copyir.com
D0 Post response signal was not detected on the sending side copyir.com Post signal was not detected on the receiving side copyir.com
D1 DCN is received copyir.com
D2 RTN/PIN is received on the sending side copyir.com RTN/PIN is received on the receiving side copyir.com
E0 A printer error occurred during a reception, and the machine is shifted into memory reception mode copyir.com However, there was not enough residual memory
E6 An error relating to the printer has occurred copyir.com
F0 The communication ended because of a WDT due to an overrun of the software copyir.com
F1 The communication ended because of an overrun of the software due to hard-ware noises copyir.com