لمینت MKP
1402-06-04
ریکوآفشیو Ricoh Aficio SP6330N
ریکوآفشیو Ricoh Aficio SP6330N
202 Polygon motor error
The polygon motor does not reach its operating speed within 10 seconds after the polygon motor on signal, or the lock signal is not detected for more than a certain time during operation ( copyir.com • Polygon motor • Polygon motor cable
220 1st laser synchronization error
The laser synchronization detector cannot detect the laser synchronization signal for more than 5 consecutive 100 ms intervals ( copyir.com • Laser synchronization detector board out of position • Laser synchronization detector board or cable defective • Laser synchronization mirror out of position • LD unit defective • Engine board defective
221 2nd laser synchronization error
The 1st LD1 is already on, but the laser synchronization detector cannot detect the laser synchronization signal from the 2nd LD for more than 5 consecutive 100 ms intervals ( copyir.com • Laser synchronization detector board out of position • LD unit defective • Engine board defective
230 FGATE error
The FGATE signal cannot be detected for 1 second after the machine has sent a start trigger ( copyir.com The FGATE signal is still detected for 13 seconds after the machine has detected the FGATE signal ( copyir.com • Engine board defective • Controller board defective • Harness broken
240 LD error
The machine detects LDB error a few times consecutively when LDB unit turns on after LDB initialization ( copyir.com • Worn-out LD unit • Disconnected or broken harness of the LD unit • LD unit defective
300 Charge roller current leak
60% or more of the PWM duty output is detected for 0 ( copyir.com 2 seconds when the charge bias is generated by the charge roller ( copyir.com • Cartridge (charge roller) defective • High voltage supply board defective
330 Development bias leak
60% or more of the PWM duty output is detected for 0 ( copyir.com 2 seconds when the development bias is generated by the development roller ( copyir.com • Cartridge (development roller) defective • High voltage supply board defective
520 Main motor lock
A main motor lock signal is not detected for more than 700 ms after the main motor starts to rotate, or the lock signal is not detected for more than a certain time during rotation after the last signal ( copyir.com • Main motor defective • Harness broken • Too much load on the drive mechanisme
530 Fusing fan error
The CPU detects the fusing fan lock signal for more than 3 seconds ( copyir.com • Poor connection of the fusing fan • Fusing fan defective
531 PSU fan error
The CPU detects the PSU fan lock signal for more than 3 seconds ( copyir.com • Poor connection of the PSU fan • PSU fan defective
541 Thermistor error
The fusing temperature detected by the thermistor is 0°C for 7 seconds after the fusing relay has been turned on ( copyir.com • Thermistor defective
542 Fusing temperature warm-up error
The fusing temperature does not increase by 7°C for 10 seconds ( copyir.com The fusing temperature does not reach more than 135°C for 24 seconds after the main switch is turned on ( copyir.com • Thermistor defective or deformed • Fusing lamp open • Fusing thermostat open
543 Fusing overheat error: Software
A fusing temperature of over 235°C is detected for 0 ( copyir.com 5 seconds by the fusing thermistor ( copyir.com • Fusing thermistor defective • Power supply board defective
544 Fusing overheat error: Software
The machine detects an overheat error of the hardware ( copyir.com • Fusing control out of control • Power supply board defective
545 Fusing lamp stays on
The fusing lamp stays on more than 12 seconds after the main motor has been turned off ( copyir.com • Fusing thermistor defective • Power supply board defective • Defective connection of the fusing unit
547 Zero cross signal malfunction
Zero cross signals are already detected for 0 ( copyir.com 15 seconds before the fusing relay-on ( copyir.com Zero cross signals are not detected for 3 seconds or the machine cannot detect a frequency ( copyir.com • Power supply board defective • Unstable main power supply condition
559 Fusing jam error: 3 counts
At the fusing exit sensor the paper jam is detected late for three pulse counts (lag error) when SP1913-001 is set to “1: Yes” ( copyir.com • Obstacle in the paper transport path • Fusing unit installed incorrectly • Fusing unit defective
620 Communication error – GAVD
The engine board detects an unknown device ( copyir.com • Engine board defective
622 Communication error – PFU
Three consecutive errors are detected during polling after the PFU is successfully detected by the machine ( copyir.com • Noise • Harness connection disconnected between the machine and PFU
641 Engine to controller communication error (no answer) ( copyir.com • Examine the connection between the controller and the engine board ( copyir.com • Replace the engine board if the error is frequent ( copyir.com
669 EEPROM error
The EEPROM error is detected at reading the prefix of the EEPROM address after power-on or recovery from the energy saver mode ( copyir.com • EEPROM not installed or incorrectly installed • EEPROM defective
670 Engine response error Engine board installed incorrectly • Engine board defective • Controller board defective
687 PER-command error
The machine does not receive PAPI-PER command for s10 seconds after PAPI-PES has been issued ( copyir.com • Controller board defective
688 Ready notification error of image data transmission
The controller does not send a ready notification of image data transmission after a sheet of paper has stopped at the registration roller ( copyir.com • Controller board defective • Communication error
819 Kernal end error • HDD error • Software application error • RAM shortage
820 Controller CPU error • Replace the controller if the error is frequent ( copyir.com
833 Self-diagnostic error: Engine I/F ASIC Replace the engine board ( copyir.com • ASIC for system control could not be detected ( copyir.com After the PCI configuration, the device ID for the ASIC could not be checked ( copyir.com Replace the mother board or check the harness connection ( copyir.com • Could not initialize or read the bus connection ( copyir.com • Value of the SSCG register is incorrect ( copyir.com
851 IEEE1394 interface error • Replace the controller if the error is frequent ( copyir.com
853 Wireless LAN Error: Card Error 1 • Wireless LAN card not inserted into the wireless LAN board
854 Wireless LAN Error: Card Error 2 • Wireless LAN card has been removed
855 Wireless LAN Error: Card Error 3 • Wireless LAN card defective • Wireless card connection not tight
856 Wireless LAN Error 4: Board • Wireless LAN card board defective • PCI connector loose
857 USB I/F Error • The USB driver can generate three types of errors: RX, CRC, and STALL errors ( copyir.com Only the STALL error can generate this SC code ( copyir.com • Defective controller board
858 HDD Encryption unit error 1 A serious error occurs when data is encrypted to update an encryption key with the HDD encryption unit ( copyir.com [Number] shows a suffix number of SC code ( copyir.com • [0], [1], [30]: Replace the controller board ( copyir.com • [2]: Replace the NVRAM ( copyir.com
859 HDD Encryption unit error 2 A serious error occurs when the HDD data is encrypted to update an encryption key with the HDD encryption unit ( copyir.com [Number] shows a suffix number of SC code ( copyir.com • [8]: Install the HDD correctly or initialize the HDD ( copyir.com • [9]: Initialize the HDD ( copyir.com • [10]: Replace the HDD or replace the controller board ( copyir.com
860 HDD start-up error • Turn off the machine and turn it back on ( copyir.com • Examine the connection between the HDD and the controller ( copyir.com • Replace the HDD if the error is frequent ( copyir.com
861 HDD: Reboot error • Loose connection of HDD • Defective cables of HDD • Defective HDD • Defective controller
863 HDD data unable to read • Replace the HDD if the error is frequent ( copyir.com
864 HDD data access error • Replace the HDD if the error is frequent ( copyir.com
865 HDD access error • Replace the HDD if the error is frequent ( copyir.com
866 SD card authentication error SD-card data is corrupted ( copyir.com • Store correct data in the SD card ( copyir.com
867 SD card error The SD card is ejected from the slot ( copyir.com • Install the SD card ( copyir.com
868 SD card access error -13 to -3 (sub-code): File system error • Format the SD card on your PC ( copyir.com • Replace the SD card ( copyir.com • Replace the controller ( copyir.com Other number (sub-code): Device error • Turn off and on the machine ( copyir.com
870 Address book error Defective software program Defective HDD Incorrect path to the server • Initialize the address book data (SP5-846-050) ( copyir.com • Initialize the HDD (SP5-832-001) ( copyir.com • Replace the HDD ( copyir.com
872 HDD mail data error Defective HDD Power failure during an access to the HDD • Initialize the HDD (SP5-832-001) ( copyir.com • Replace the HDD ( copyir.com
873 HDD mail transfer error Defective HDD Power failure during an access to the HDD • Initialize the HDD (SP5-832-001) ( copyir.com • Replace the HDD ( copyir.com
874 Delete All error 1: HDD Data Overwrite Security Unit (SD card) not installed Defective HDD • Install the Data Overwrite Security Unit (D377) ( copyir.com • Replace the HDD ( copyir.com
875 Delete All error 2: Data area • The logical format for the HDD fails ( copyir.com
876 Log Data Error
877 HDD Data Overwrite Security SD card error Defective SD card (M352) SD card (M352) not installed • Replace the NVRAM and then install the new SD card (M352) ( copyir.com • Check and reinstall the SD card (M352) ( copyir.com
878 TPM system authentication error Incorrect updating for the system firmware Defective flash ROM on the controller board • Replace the controller board ( copyir.com
900 Controller counter errorn error • Replace the NVRAM if the error is frequent ( copyir.com
920 Printer application error error Defective software Unexpected hardware resource (e ( copyir.com g ( copyir.com , memory shortage) • Software defective; switch off/on, or change the controller firmware if the problem is not solved • Insufficient memory
921 Printer font error A necessary font is not found in the SD card ( copyir.com The SD card data is corrupted ( copyir.com • Check that the SD card has the correct data ( copyir.com
990 Software performance error • Software defective; reboot the machine • Internal parameter incorrect • Insufficient working memory • When this SC occurs, the file name, address, and data will be stored in NVRAM ( copyir.com Note the above data and the situation in which this SC occurs ( copyir.com Then report the data and conditions to your technical control center ( copyir.com
991 Software continuity error error • Software bug; reboot the machine • Internal parameter incorrect • Insufficient working memory
992 Undefined error Defective software program • An error undetectable by any other SC code occurred??§??“
998 Application start error • Software defective; change the firmware for the application that failed • An option required by the application (RAM, DIMM, board) is not installed
اشتراک گذاری در:
پست های مرتبط
جستجو در مطالب
مطالب جدید ...
در خبرنامه ما عضو شوید
