لمینت MKP
1402-06-04
Menu
E7-01 Image data error Communication error with the E-sort module MCU PWB trouble ASIC trouble
E7-06 Image data decode error
Image expansion error MCU PWB abnormality USB cable trouble
E7-10 Shading trouble (Black correction copyir.com
The CCD black scan level is abnormal when the shading. Improper connection of the CCD unit flat cable CCD unit abnormality MCU PWB abnormality
E7-11 Shading trouble (White correction copyir.com
The CCD white scan level is abnormal when the shading. Improper connection of the CCD unit flat cable Dirt on the mirror, the lens, and the reference white plate Copy lamp lighting abnormality CCD unit abnormality MCU PWB abnormality (When occurred in the SPF scan position. copyir.com Improper installation of the mirror unit
E7-16 Abnormal laser output
When the laser output is stopped, HSYNC is detected. Laser abnormality MCU PWB abnormality.
E7-20 LSU trouble
The BD signal from the LSU cannot be detected in a certain cycle. (Always OFF or always ON copyir.com LSU connector or LSU harness defect or disconnection Polygon motor rotation abnormality Laser beams are not generated. MCU PWB abnormality.
F2-64 Toner supply abnormality
The maximum toner supply time is greatly exceeded. CRUM chip trouble Improper developing unit
F2-70 Improper cartridge
The destination of the main unit differs from that of the CRUM. When the life cycle information is other than Not Used (FFh copyir.com. CRUM chip trouble Improper developing unit
F2-74 Toner cartridge CRUM error PCU Toner cartridge (CRUM copyir.com trouble. PCU PWB trouble. Connector/harness trouble.
F5-02 Copy lamp lighting abnormality
The copy lamp does not turn on. Copy lamp abnormality Copy lamp harness abnormality CCD PWB harness abnormality.
H2-00 Thermistor open
The thermistor is open. The fusing unit is not installed. Thermistor abnormality Control PWB abnormality Fusing section connector disconnection The fusing unit is not installed.
H3-00 Heat roller high temperature detection
The fusing temperature exceeds 240°C. Thermistor abnormality Control PWB abnormality Fusing section connector disconnection.
H4-00 Heat roller low temperature detection
1 copyir.com When the target temperature (165°C copyir.com is not reached in 55 sec after starting warming-up. 2 copyir.com When the temperature below 100°C is detected for 300ms under the ready print state. “Starting warming-up” means not only that in power supply but also reset that in reset from shut-off and in side door close. (The timing of generating H4 is not limited to that in power supply. copyir.com Thermistor abnormality Heater lamp abnormality Thermostat abnormality Control PWB abnormality
L1-00 Feeding is not completed within the specified time after starting feeding. (The scan head locking switch is locked copyir.com
The white area and the black marking on the shading plate are used to obtain the difference in the CCD level values for judgment of lock. When the difference in the levels of which and black is small, it is judged that the black mark could not be scanned by lock and the trouble code “L1” is displayed. The scan head is locked by the lock switch. Mirror unit abnormality The scanner wire is disconnected. The origin detection sensor abnormality Mirror motor harness abnormality
L3-00 Scanner return trouble
When the mirror base is returned for the specified time (6 sec copyir.com in mirror initializing after turning on the power, the mirror home position sensor (MHPS copyir.com does not turn ON. Or when the mirror base is returned for the specified time (about 6 sec copyir.com after start of copy return, the mirror home position sensor (MHPS copyir.com does not turn ON. Mirror unit abnormality Scanner wire disconnection Origin detection sensor abnormality Mirror motor harness abnormality
L4-01 Main motor lock detection
When the main motor encoder pulse is not detected for 100 msec. Main motor unit abnormality Improper connection or disconnection the main motor and the harness. MCU PWB abnormality
L4-31 Exhaust fan motor lock detection trouble
The error detection is started after 2 sec from starting rotation of the exhaust fan motor. 1 copyir.com The continuous rotation state of 250ms is not detected for 1 sec after starting detection. 2 copyir.com When the lock sensor (in the exhaust fan copyir.com detects the HIGH level (unstable copyir.com after detection the lock state (stable state copyir.com. Exhaust fan motor connector connection trouble Exhaust fan motor trouble MCU PWB trouble
L6-10 Polygon motor lock detection
The lock signal (specified rpm signal copyir.com does not return within a certain time (about 20 sec copyir.com from starting the polygon motor rotation. Polygon motor unit abnormality Improper connection or disconnection of the polygon motor and the harness. MCU PWB abnormality
U2-00 EEPROM read/write error (Serial communication error copyir.com EEPROM abnormality
U2-11 Counter check sum error (EEPROM copyir.com
Check sum error of the counter area in the EEPROM EEPROM abnormality
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.