لمینت MKP
1402-06-04
Menu
E000-0001 Fixing Assembly low temperature error
The detected temperature of the Fixing Main Thermistor (THM1) failed to reach the specified temperature at the fixing start control copyir.com 1 copyir.com Perform the following to clear the error: COPIER > FUNCTION > CLEAR > ERR in the Service Mode; then, turn the power switch to OFF and then ON copyir.com
2 copyir.com Check the connection of the Fixing Assembly copyir.com (Connection error of the Drawer, connector disconnection, open circuit)
3 copyir.com Check the connection between the AC Driver PCB (PCB4) and Fixing Assembly copyir.com
4 copyir.com Replace the Fixing Assembly copyir.com
5 copyir.com Replace the AC Driver PCB (PCB4) copyir.com
6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E001-0000 Fixing Assembly high temperature error
The Fixing Main Thermistor (THM1) detected 250 degrees C or higher for 200msec or longer on end copyir.com 1 copyir.com Perform the following to clear the error: COPIER > FUNCTION > CLEAR > ERR in the Service Mode; then, turn the power switch to OFF and then ON copyir.com
2 copyir.com Check the connection of the Fixing Assembly copyir.com (Connection error of the Drawer, connector disconnection, open circuit)
3 copyir.com Check the connection between the AC Driver PCB (PCB4) and Fixing Assembly copyir.com
4 copyir.com Replace the Fixing Assembly copyir.com
5 copyir.com Replace the AC Driver PCB (PCB4) copyir.com
6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E001-0001 Fixing Assembly high temperature error (hardware detection)
The hardware circuit detected overheating of the Fixing Main Thermistor (THM1) or Fixing Sub Thermistor (THM2) for 30msec or longer on end copyir.com 1 copyir.com Perform the following to clear the error: COPIER > FUNCTION > CLEAR > ERR in the Service Mode; then, turn the power switch to OFF and then ON copyir.com
2 copyir.com Check the connection of the Fixing Assembly copyir.com (Connection error of the Drawer, connector disconnection, open circuit)
3 copyir.com Check the connection between the AC Driver PCB (PCB4) and Fixing Assembly copyir.com
4 copyir.com Replace the Fixing Assembly copyir.com
5 copyir.com Replace the AC Driver PCB (PCB4) copyir.com
6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E001-0002 Fixing Assembly high temperature error
The Fixing Sub Thermistor (THM2) detected 295 degrees C or higher for 200msec or longer on end copyir.com 1 copyir.com Perform the following to clear the error: COPIER > FUNCTION > CLEAR > ERR in the Service Mode; then, turn the power switch to OFF and then ON copyir.com
2 copyir.com Check the connection of the Fixing Assembly copyir.com (Connection error of the Drawer, connector disconnection, open circuit)
3 copyir.com Check the connection between the AC Driver PCB (PCB4) and Fixing Assembly copyir.com
4 copyir.com Replace the Fixing Assembly copyir.com
5 copyir.com Replace the AC Driver PCB (PCB4) copyir.com
6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E002-0000 Fixing Assembly temperature rise error
1 copyir.com The Fixing Main Thermistor (THM1) detected the temperature of lower than 115 degrees C for 400msec or longer on end 6 copyir.com0 seconds later after detecting 100 degrees C copyir.com
2 copyir.com The Fixing Main Thermistor (THM1) detected the temperature of lower than 150 degrees C for 400msec or longer on end 6 copyir.com0 seconds later after detecting 140 degrees C copyir.com 1 copyir.com Perform the following to clear the error: COPIER > FUNCTION > CLEAR > ERR in the Service Mode; then, turn the power switch to OFF and then ON copyir.com
2 copyir.com Check the connection of the Fixing Assembly copyir.com (Connection error of the Drawer, connector disconnection, open circuit)
3 copyir.com Check the connection between the AC Driver PCB (PCB4) and Fixing Assembly copyir.com
4 copyir.com Replace the Fixing Assembly copyir.com
5 copyir.com Replace the AC Driver PCB (PCB4) copyir.com
6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E003-0000 Fixing Assembly temperature decrease error (during printing)
1 copyir.com The Fixing Main Thermistor (THM1) detected the temperature of lower than 80 degrees C for 200msec or longer on end copyir.com
2 copyir.com The Fixing Sub Thermistor (THM2) detected the temperature of lower than 60 degrees C for 200msec or longer on end copyir.com 1 copyir.com Perform the following to clear the error: COPIER > FUNCTION > CLEAR > ERR in the Service Mode; then, turn the power switch to OFF and then ON copyir.com
2 copyir.com Check the connection of the Fixing Assembly copyir.com (Connection error of the Drawer, connector disconnection, open circuit)
3 copyir.com Check the connection between the AC Driver PCB (PCB4) and Fixing Assembly copyir.com
4 copyir.com Replace the Fixing Assembly copyir.com
5 copyir.com Replace the AC Driver PCB (PCB4) copyir.com
6 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E004-0000 Thermistor disconnection detection error
The disconnection of the thermistor connector was detected for 30msec on end copyir.com 1 copyir.com Check the connection of the Fixing Assembly copyir.com (Connection error of the Drawer, connector disconnection, open circuit)
2 copyir.com Check the connection between the AC Driver PCB (PCB4) and Fixing Assembly copyir.com
3 copyir.com Replace the Fixing Assembly copyir.com
4 copyir.com Replace the AC Driver PCB (PCB4) copyir.com
5 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E010-0001 Main Motor (M2) rotation error
The lock signal was not detected for 2 copyir.com0 seconds while detecting the signal every 100msec since starting the drive of the motor copyir.com 1 copyir.com Check the connector connection between the Main Motor (M2) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Main Motor (M2) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E010-0002 Main Motor (M2) rotation error
The lock signal was not detected 5 times in a row for 500msec while detecting the signal every 100msec during driving (after the lock signal detection) copyir.com 1 copyir.com Check the connector connection between the Main Motor (M2) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Main Motor (M2) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E013-0000 Waste Toner Motor (M3) rotation error
The same level of the lock signal was detected 375 times in a row while detecting the signal every 2msec copyir.com
* If paper is being fed, the error occurs after the paper has been delivered copyir.com 1 copyir.com Check the connector connection between the Waste Toner Motor (M3) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Waste Toner Motor (M3) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E014-0001 Fixing Motor (M1) rotation error
The lock signal was not detected for 2 copyir.com0 seconds while detecting the signal every 100msec since starting the drive of the motor copyir.com 1 copyir.com Check the connector connection between the Fixing Motor (M1) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Fixing Motor (M1) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E014-0002 Fixing Motor (M1) rotation error
The lock signal was not detected 5 times in a row for 500msec while detecting the signal every 100msec during driving (after the lock signal detection) copyir.com 1 copyir.com Check the connector connection between the Fixing Motor (M1) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Fixing Motor (M1) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E014-0003 Fixing Motor (M1) pressure release error
The pressure release of the Fixing Assembly was not detected for 3 copyir.com0 seconds during the pressure release drive copyir.com 1 copyir.com Check the connector connection between the Fixing Pressure Release Sensor (PS18) or the Fixing Motor (M1) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Fixing Pressure Release Sensor (PS18) copyir.com
3 copyir.com Replace the Fixing Motor (M1) copyir.com
4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E014-0004 Fixing Motor (M1) pressurization error
The pressurization of the Fixing Assembly was not detected for 3 copyir.com0 seconds during the pressurization drive copyir.com 1 copyir.com Check the connector connection between the Fixing Pressure Release Sensor (PS18) or the Fixing Motor (M1) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Fixing Pressure Release Sensor (PS18) copyir.com
3 copyir.com Replace the Fixing Motor (M1) copyir.com
4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E020-0000 Detection of the toner clog between the Hopper Unit and the Developing Assembly
When the Developing Assembly Toner Sensor (TS2) detected “toner-absent” and the Hopper Toner Sensor (TS1) detected “toner-present”, the Developing Assembly Toner Sensor (TS2) did not detect “toner-present” though the Hopper Motor (M6) rotated by 194 times at intervals of 1 copyir.com0 second with having turned on the Developing Cylinder Clutch (CL2) copyir.com
* If paper is being fed, the error occurs after the paper has been delivered copyir.com 1 copyir.com Check the rotation of the Hopper Motor Gear copyir.com (If it is rotating, the sensor may not be detecting correctly copyir.com In that case, perform the following to supply toner to the Developing Assembly: COPIER > FUNCTION > INSTALL > TONER-S in the Service Mode copyir.com)
2 copyir.com Replace the Developing Assembly copyir.com
3 copyir.com Replace the Hopper Unit copyir.com
4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E024-0001 Disconnection of the Developing Assembly Toner Sensor (TS2)
1 copyir.com At normal speed: The Developing Assembly Toner Sensor (TS2) signal was detected 7500 times in a row at intervals of 100msec copyir.com
2 copyir.com At low speed: The Developing Assembly Toner Sensor (TS2) signal was detected 4500 times in a row at intervals of 100msec copyir.com
* If paper is being fed, the error occurs after the paper has been delivered copyir.com 1 copyir.com Check the connector connection between the Developing Assembly and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Developing Assembly copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E025-0000 Connector disconnection of the Hopper Toner Sensor (TS1)
The connection signal of the Hopper Toner Sensor (TS1) was not detected 10 times in a row for 100msec copyir.com
* If paper is being fed, the error occurs after the paper has been delivered copyir.com 1 copyir.com Check the connector connection between the Hopper Unit and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Hopper Unit copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E025-0001 Bottle Motor (M5) rotation error
The same level of the Bottle Motor (M5) lock signal was detected 230 times in a row while detecting the signal every 2 copyir.com0msec copyir.com
* If paper is being fed, the error occurs after the paper has been delivered copyir.com 1 copyir.com Check the connector connection between the Bottle Motor (M5) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Bottle Motor (M5) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E110-0001 Laser Scanner Motor rotation error
After startup of the Laser Scanner Motor, the speed lock signal of the Laser Scanner Motor was not detected although a specified period of time had passed copyir.com
*When the same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Laser Scanner Unit and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Laser Scanner Unit copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E110-0002 Laser Scanner Motor rotation error
After the speed lock of the Laser Scanner Motor settled, the speed lock signal was not detected 10 times in a row at intervals of 100msec copyir.com
*When the same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Laser Scanner Unit and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Laser Scanner Unit copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1
E110-0003 Laser Scanner Motor rotation error
The speed lock signal of the Laser Scanner Motor was not detected although 6 copyir.com5 seconds (when switching from low speed to normal speed) or 8 copyir.com0 seconds (when switching from normal speed to low speed) had passed copyir.com
*When the same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Laser Scanner Unit and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Laser Scanner Unit copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E196-0000 EEPROM access error
During communication with EEPROM, the communication failed to retry 20 times after the communication error had occurred copyir.com
* If paper is being fed, the error occurs after the paper has been delivered copyir.com 1 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E197-0000 Laser Driver PCB communication error
Error in communication with the Laser Driver PCB (communication data failure)
*When the same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Laser Scanner Unit and the Main Controller PCB (PCB2) or the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Laser Scanner Unit copyir.com
3 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E197-0003 Connector disconnection of the Laser Scanner Unit
The disconnection of the Laser Scanner Unit was detected copyir.com 1 copyir.com Check the connector connection between the Laser Scanner Unit and the Main Controller PCB (PCB2) or the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Laser Scanner Unit copyir.com
3 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E202-0001 CIS Unit home position detection error
The CIS HP Sensor (PS24) did not detect the CIS Unit 1 copyir.com Check the connection of the Flexible Cable between the Reader Controller PCB (PCB3) and the Main Controller PCB (PCB2) copyir.com
2 copyir.com Replace the Flexible Cable copyir.com
3 copyir.com Replace the CIS HP Sensor (PS24) copyir.com
4 copyir.com Replace the Reader Motor (M10) copyir.com
5 copyir.com Replace the Reader Controller PCB (PCB3) copyir.com
6 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E202-0002 CIS Unit home position detection error
The CIS Unit did not come off the CIS HP Sensor (PS24) copyir.com 1 copyir.com Check the connection of the Flexible Cable between the Reader Controller PCB (PCB3) and the Main Controller PCB (PCB2) copyir.com
2 copyir.com Replace the Flexible Cable copyir.com
3 copyir.com Replace the CIS HP Sensor (PS24) copyir.com
4 copyir.com Replace the Reader Motor (M10) copyir.com
5 copyir.com Replace the Reader Controller PCB (PCB3) copyir.com
6 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E240-0000 Controller communication error
A serial communication error was detected during normal operation copyir.com 1 copyir.com Check the connector connection between the DC Controller PCB (PCB1) and the Main Controller PCB (PCB2) copyir.com
2 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E240-0001 Controller communication error
A serial communication error was detected during printing copyir.com 1 copyir.com Check the connector connection between the DC Controller PCB (PCB1) and the Main Controller PCB (PCB2) copyir.com
2 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E246 System error Contact the service company office
E247 System error Contact the service company office
E248-0000 Reader backup data read error
The verification of the reader backup data failed to match copyir.com 1 copyir.com Check the connector connection between the Reader Controller PCB (PCB3) and the Main Controller PCB (PCB2) copyir.com
2 copyir.com Replace the Reader Controller PCB (PCB3) copyir.com
3 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E261-0000 Zero cross signal error
The zero cross signal was not detected for 500msec or longer while the relay turned to on copyir.com
*When the same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection copyir.com (All connectors on the DC Controller PCB)
2 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
3 copyir.com Replace the AC Driver PCB (PCB4) copyir.com
E315-0007 Image process device error
JBIG encode error 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check connection of Main Controller PCB copyir.com
3 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E315-000d Image process device error
JBIG decode error 1 copyir.com Delete the current job copyir.com
2 copyir.com Turn OFF and then ON the main power copyir.com
3 copyir.com Check connection of Main Controller PCB copyir.com
4 copyir.com Replace the DDR-SDRAM, the HDD and Main Controller PCB (PCB2) at the same time copyir.com
E315-000e Image process device error
Error at software decoding 1 copyir.com Delete the current job copyir.com
2 copyir.com Turn OFF and then ON the main power copyir.com
3 copyir.com Check connection of Main Controller PCB copyir.com
4 copyir.com Replace the DDR-SDRAM, the HDD and Main Controller PCB (PCB2) at the same time copyir.com
E315-000f Image process device error
Error at MemoryCopy 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check connection of Main Controller PCB copyir.com
3 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E315-0027 Image process device error
ROTU timeout error 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check connection of Main Controller PCB copyir.com
3 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E315-0035 Image process device error
MemFill timeout error 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check connection of Main Controller PCB copyir.com
3 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E315-0100 Image process device error
PRIO overrun 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check connection of Main Controller PCB copyir.com
3 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E315-0500 Device timeout
An image synchronous signal from the Main Controller PCB to the Reader is not received within 30 seconds copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0501 Device abnormal completion
An abnormal signal from the Main Controller PCB to the Reader is detected copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0510 Device timeout
An image synchronous signal from the Main Controller PCB to the Reader is not received within 30 seconds copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0511 Device abnormal completion
An abnormal signal from the Main Controller PCB to the Reader is detected copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0520 Device timeout
An image synchronous signal from the Main Controller PCB to the Reader is not received within 30 seconds copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0521 Device abnormal completion
An abnormal signal from the Main Controller PCB to the Reader is detected copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0530 Device timeout
An image synchronous signal from the Main Controller PCB to the Reader is not received within 30 seconds copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0531 Device abnormal completion
An abnormal signal from the Main Controller PCB to the Reader is detected copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0540 Device timeout
An image synchronous signal from the Main Controller PCB to the Reader is not received within 30 seconds copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0541 Device abnormal completion
An abnormal signal from the Main Controller PCB to the Reader is detected copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0550 Device timeout
An image synchronous signal from the Main Controller PCB to the Reader is not received within 30 seconds copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E315-0551 Device abnormal completion
An abnormal signal from the Main Controller PCB to the Reader is detected copyir.com 1 copyir.com Turn OFF and then ON the main power copyir.com
2 copyir.com Check the connection of the Main Controller PCB (including the flat cable) copyir.com
3 copyir.com Replace the flat cable copyir.com
4 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E350 System error Contact the service company office
E351-0000 Main Controller PCB communication error 1 copyir.com Turn OFF and then ON the main power
2 copyir.com Disconnect and then connect the connector of the Main Controller PCB copyir.com
3 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E354 System error Contact the service company office
E355 System error Contact the service company office
E500-0000 Communication error
As for the communication with the Finisher and the Host Machine, the retry of the communication was over the specified number of times copyir.com 1 copyir.com Check the installation of the Host Machine and the Finisher copyir.com
2 copyir.com Check the connector connection between the DC Controller PCB (PCB1) and the Finisher Controller PCB (PCB1) copyir.com
3 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E530-0001 Front Alignment Motor (M4) error
At initialization of the Front Alignment Plate, the Front Alignment Plate failed to move from the Front Alignment Plate HP Sensor (S4) although the Front Alignment Motor (M4) was driven for 10mm copyir.com 1 copyir.com Check the connector connection of the Front Alignment Plate HP Sensor (S4) or the Front Alignment Motor (M4) copyir.com
2 copyir.com Replace the Front Alignment Plate HP Sensor (S4) copyir.com
3 copyir.com Replace the Front Alignment Motor (M4) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E530-0002 Front Alignment Motor (M4) error
At initialization of the Front Alignment Plate, the Front Alignment Plate failed to be detected by the Front Alignment Plate HP Sensor (S4) although the Front Alignment Motor (M4) was driven for 780msec copyir.com 1 copyir.com Check the connector connection of the Front Alignment Plate HP Sensor (S4) or the Front Alignment Motor (M4) copyir.com
2 copyir.com Replace the Front Alignment Plate HP Sensor (S4) copyir.com
3 copyir.com Replace the Front Alignment Motor (M4) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E531-8001 Staple Motor (M9) error
The Stapler failed to move from the Staple HP Sensor (S11) within the staple execution time (450msec) copyir.com 1 copyir.com Check the connector connection of the Staple Unit copyir.com
2 copyir.com Replace the Staple Unit copyir.com
3 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E531-8002 Staple Motor (M9) error
After execution of staple operation, the Staple Unit could not be detected by the Staple HP Sensor (S11) within 460msec although the motor was operated in the positive direction copyir.com And then, the Staple Unit could not be detected by the Staple HP Sensor (S11) within 460msec although the motor was rotated in the negative direction copyir.com 1 copyir.com Check the connector connection of the Staple Unit copyir.com
2 copyir.com Replace the Staple Unit copyir.com
3 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E537-0001 Rear Alignment Motor (M5) error
At initialization of the Rear Alignment Plate, the Rear Alignment Plate failed to move from the Rear Alignment Plate HP Sensor (S5) although the Rear Alignment Motor (M5) was driven for 10mm copyir.com 1 copyir.com Check the connector connection of the Rear Alignment Plate HP Sensor (S5) or the Rear Alignment Motor (M5) copyir.com
2 copyir.com Replace the Rear Alignment Plate HP Sensor (S5) copyir.com
3 copyir.com Replace the Rear Alignment Motor (M5) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E537-0002 Rear Alignment Motor (M5) error
At initialization of the Rear Alignment Plate, the Rear Alignment Plate failed to be detected by the Rear Alignment Plate HP Sensor (S5) although the Rear Alignment Motor (M5) was driven for 760msec copyir.com 1 copyir.com Check the connector connection of the Rear Alignment Plate HP Sensor (S5) or the Rear Alignment Motor (M5) copyir.com
2 copyir.com Replace the Rear Alignment Plate HP Sensor (S5) copyir.com
3 copyir.com Replace the Rear Alignment Motor (M5) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E540-0001 Stack Tray Shift Motor (M8) error
The Stack Tray shifting operation could not be completed although the Stack Tray Shift Motor (M8) was driven for 4 copyir.com0 seconds copyir.com 1 copyir.com Check the connector connection of the Stack Tray Paper Height Sensor (S9) or the Stack Tray Shift Motor (M8) copyir.com
2 copyir.com Replace the Stack Tray Paper Height Sensor (S9) copyir.com
3 copyir.com Replace the Stack Tray Shift Motor (M8) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E575-0001 Gripper Motor (M7) error
When the Gripper Motor (M7) was driven, the Gripper failed to move from the Gripper HP Sensor (S7) although the Gripper Encoder Sensor (S8) detected the rotation of 100 clocks copyir.com 1 copyir.com Check the connector connection of the Gripper HP Sensor (S7), Gripper Encoder Sensor (S8) or the Gripper Motor (M7) copyir.com
2 copyir.com Replace the Gripper HP Sensor (S7) copyir.com
3 copyir.com Replace the Gripper Encoder Sensor (S8) copyir.com
4 copyir.com Replace the Gripper Motor (M7) copyir.com
5 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E575-0002 Gripper Motor (M7) error
The Gripper failed to be detected by the Gripper HP Sensor (S7) although the Gripper Motor (M7) was driven for specified times (1 copyir.com7 seconds at initialization or 1 copyir.com4 seconds at normal operation) copyir.com 1 copyir.com Check the connector connection of the Gripper HP Sensor (S7) or the Gripper Motor (M7) copyir.com
2 copyir.com Replace the Gripper HP Sensor (S7) copyir.com
3 copyir.com Replace the Gripper Motor (M7) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E575-0004 Gripper Motor (M7) clock error
When the Gripper Motor (M7) was driven, the Gripper Encoder Sensor (S8) detected the rotation of 400 clocks or more copyir.com 1 copyir.com Check the connector connection of the Gripper Encoder Sensor (S8) or the Gripper Motor (M7) copyir.com
2 copyir.com Replace the Gripper Encoder Sensor (S8) copyir.com
3 copyir.com Replace the Gripper Motor (M7) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E577-0001 Paddle Motor (M3) error
The Paddle failed to move from the Paddle HP Sensor (S3) although the Paddle Motor (M3) was driven for 175 steps copyir.com 1 copyir.com Check the connector connection of the Paddle HP Sensor (S3) or the Paddle Motor (M3) copyir.com
2 copyir.com Replace the Paddle HP Sensor (S3) copyir.com
3 copyir.com Replace the Paddle Motor (M3) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E577-0002 Paddle Motor (M3) error
The Paddle failed to be detected by the Paddle HP Sensor (S3) although the Paddle Motor (M3) was driven for 2 copyir.com0 seconds copyir.com 1 copyir.com Check the connector connection of the Paddle HP Sensor (S3) or the Paddle Motor (M3) copyir.com
2 copyir.com Replace the Paddle HP Sensor (S3) copyir.com
3 copyir.com Replace the Paddle Motor (M3) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E583-0001 Tray Auxiliary Guide Motor (M6) error
The Tray Auxiliary Guide failed to move from the Tray Auxiliary Guide HP Sensor (S6) although the Tray Auxiliary Guide Motor (M6) was driven for 30mm copyir.com 1 copyir.com Check the connector connection of the Tray Auxiliary Guide HP Sensor (S6) or the Tray Auxiliary Guide Motor (M6) copyir.com
2 copyir.com Replace the Tray Auxiliary Guide HP Sensor (S6) copyir.com
3 copyir.com Replace the Tray Auxiliary Guide Motor (M6) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E583-0002 Tray Auxiliary Guide Motor (M6) error
The Tray Auxiliary Guide failed to be detected by the Tray Auxiliary Guide HP Sensor (S6) although the Tray Auxiliary Guide Motor (M6) was driven for 1 copyir.com8 seconds 1 copyir.com Check the connector connection of the Tray Auxiliary Guide HP Sensor (S6) or the Tray Auxiliary Guide Motor (M6) copyir.com
2 copyir.com Replace the Tray Auxiliary Guide HP Sensor (S6) copyir.com
3 copyir.com Replace the Tray Auxiliary Guide Motor (M6) copyir.com
4 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
E602 File system error on the HDD
E604-0512 Image memory is faulty or insufficient
512MB memory needs to be installed (insufficient memory for the model) 1 copyir.com Install a 512MB or larger main memory
E604-1024 Image memory is faulty or insufficient
1024MB memory needs to be installed (insufficient memory for the model) 1 copyir.com Install a 1024MB or larger main memory
E604-1536 Image memory is faulty or insufficient
1536MB memory needs to be installed (insufficient memory for the model) 1 copyir.com Install a 1536MB or larger main memory
E611-0000 An error code to prevent repeated resend due to power shutdown during FAX transmission
Repeated rebooting and resending in a short period of time 1 copyir.com Clear the FAX job information copyir.com
Execute the following: COPIER > FUNCTION > CLEAR > FXTX-CLR
2 copyir.com Turn OFF and ON the main power copyir.com
E613-0512 Image memory is faulty or insufficient
No necessary memory at Main Controller PCB Make a 512MB memory at Main Controller PCB (PCB2) copyir.com
E613-1024 Image memory is faulty or insufficient
No necessary memory at Main Controller PCB Make a 1024MB memory at Main Controller PCB (PCB2) copyir.com
E613-1536 Image memory is faulty or insufficient
No necessary memory at Main Controller PCB Make a 1536MB memory at Main Controller PCB (PCB2) copyir.com
E614 Flash PCB detection error
E674-0001 FAX Board communication error
The specified number of errors was detected with FAX Board communication 1 copyir.com Check wire connection between the FAX Board and the Main Controller PCB copyir.com
2 copyir.com Replace the FAX Board copyir.com
3 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E674-0004 FAX Board communication error
Error in access of the modem IC used by FAX 1 copyir.com Check wire connection between the FAX Board and the Main Controller PCB copyir.com
2 copyir.com Replace the FAX Board copyir.com
3 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E674-0008 FAX Board communication error
Error in access of the port IC used by OnBoardFax 1 copyir.com Check wire connection between the FAX Board and the Main Controller PCB copyir.com
2 copyir.com Replace the FAX Board copyir.com
3 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E674-000C FAX Board communication error
An error was detected in access of the modem IC or port IC used by Fax 1 copyir.com Check wire connection between the FAX Board and the Main Controller PCB copyir.com
2 copyir.com Replace the FAX Board copyir.com
3 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E674-0010 FAX Board communication error
Error in timer device to be used by FAX at activation 1 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E674-0011 FAX Board communication error
Error when the timer device to be used by FAX is started 1 copyir.com Replace the Main Controller PCB (PCB2) copyir.com
E674-0030 FAX Board communication error
Checksum error of USB-FAX MAINROM When the power is turned ON, get in the download mode from service mode to execute downloading of USBFAX MAINROM copyir.com
E674-0100 FAX Board communication error
After completion of fax communication, writing of the communication information (log) failed, and the log cannot be read copyir.com Turn OFF and then ON the power copyir.com Points to note) All the previous communication information will be cleared copyir.com
E674-0200 HDD access error
An error occurred when accessing the HDD copyir.com 1 copyir.com Turn OFF and then ON the power copyir.com 2 copyir.com System all format and installation 3 copyir.com Replace the HDD copyir.com 4 copyir.com Replace the Main Controller PCB copyir.com
E677-0003 Print server error
Error is detected by checking of the mother board at startup of the print server 1 copyir.com Check cable connection and turn ON the power again copyir.com
2 copyir.com Reinstall the printer server copyir.com
E711-0001 Communication error (retransmission request reception error)
Communication between the Host Machine and the Finisher was lost copyir.com 1 copyir.com Check the installation of the Host Machine and the Finisher copyir.com
2 copyir.com Check the connector connection between the DC Controller PCB (PCB1) and the Finisher Controller PCB (PCB1) copyir.com
3 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E713-0000 Error in communication with the Finisher (communication retry failure)
The communication did not connect again although the error retry was executed after failing to communicate with the Finisher copyir.com 1 copyir.com Check the installation of the Host Machine and the Finisher copyir.com
2 copyir.com Check the connector connection between the DC Controller PCB (PCB1) and the Finisher Controller PCB (PCB1) copyir.com
3 copyir.com Replace the Finisher Controller PCB (PCB1) copyir.com
4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E716-0000 Error in communication with the Cassette Module
The communication did not connect again although the error retry was executed after failing to communicate with the Cassette Module copyir.com 1 copyir.com Check the installation of the Host Machine and the Cassette Module copyir.com
2 copyir.com Check the connector connection between the DC Controller PCB (PCB1) and the Cassette Module Controller PCB (PCB101) copyir.com
3 copyir.com Replace the Cassette Module Controller PCB (PCB101) copyir.com
4 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E719-0001 Coin vendor error
Error when the coin vendor is started
– The Coin Vendor, which must have been connected before the power was turned OFF, is not connected when the power is turned ON Check cable connection between the charging management equipment and the host machine copyir.com
While the charging management equipment is connected for operation, clear the error in the case of switching to the operation without the charging management equipment copyir.com
(To prevent a misuse by removing the charging management equipment, this error code is displayed copyir.com)
E719-0002 Coin vendor error
IPC error at coin vendor operation
– Open circuit of IPC, unable to recover the IPC communication
– When open circuit of the pickup/delivery signal cable is detected
– Invalid connection is detected Check cable connection between the charging management equipment and the host machine copyir.com
While the charging management equipment is connected for operation, clear the error in the case of switching to the operation without the charging management equipment copyir.com
(To prevent a misuse by removing the charging management equipment, this error code is displayed copyir.com)
E719-0003 Coin vendor error
– Communication error with the coin manager occurs during unit price acquisition at startup copyir.com Check cable connection between the charging management equipment and the host machine copyir.com
While the charging management equipment is connected for operation, clear the error in the case of switching to the operation without the charging management equipment copyir.com
(To prevent a misuse by removing the charging management equipment, this error code is displayed copyir.com)
E719-0004 Coin vendor error
The coin vendor was connected to a model that does not support the coin vendor 1 copyir.com Disconnect the coin vendor copyir.com
E719-0011 Coin vendor error
Error when the NewCardReader is started
– The NewCardReader, which must have been connected before the power was turned OFF, is not connected when the power is turned ON copyir.com) Check cable connection between the charging management equipment and the host machine copyir.com
While the charging management equipment is connected for operation, clear the error in the case of switching to the operation without the charging management equipment copyir.com
(To prevent a misuse by removing the charging management equipment, this error code is displayed copyir.com)
E719-0012 Coin vendor error
IPC error at NewCardReader operation
Open circuit of IPC, unable to recover the IPC communication Check cable connection between the charging management equipment and the host machine copyir.com
While the charging management equipment is connected for operation, clear the error in the case of switching to the operation without the charging management equipment copyir.com
(To prevent a misuse by removing the charging management equipment, this error code is displayed copyir.com)
E719-0031 Serial communication error when the NewCardReader is started
Unable to start communication with the Serial NewCardReader at startup 1 copyir.com Check if the cable of Serial NewCardReader is open circuit copyir.com
2 copyir.com Remove the Serial NewCardReader copyir.com
COPIER > Function > CLEAR > CARD
COPIER > Function > CLEAR > ERR
E719-0032 Serial communication error after the NewCardReader was started
Although communication with the Card Reader was possible at startup, it became unavailable in the middle of communication Check if the NewCardReader cable is open circuit
E730-1001 PDL software erro
rInitialization error 1 copyir.com PDL reset processing (user mode > function settings > printer > printer settings > utility > Reset Printer) copyir.com
2 copyir.com Turn OFF and then ON the power copyir.com
E730-100A PDL software error
Systematic fatal error occurs 1 copyir.com PDL reset processing (user mode > function settings > printer > printer settings > utility > Reset Printer) copyir.com
2 copyir.com Turn OFF and then ON the power copyir.com
E730-A006 PDL communication error
No reply from PDL copyir.com No reply from PDL due to failure or absence of the controller firmware 1 copyir.com PDL reset processing (user mode > function settings > printer > printer settings > utility > Reset Printer) copyir.com
2 copyir.com Turn OFF and then ON the power copyir.com
3 copyir.com Check connection of Main Controller PCB copyir.com
4 copyir.com Reinstall the controller firmware copyir.com
5 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E730-A007 Mismatched PDL version
Mismatch in version of the control software between the host machine and the PDL copyir.com System all format and installation copyir.com
E730-B013 PDL embedded font error
Broken font data 1 copyir.com Turn OFF and then ON the power copyir.com
2 copyir.com Reinstall the system using SST or USB copyir.com
3 copyir.com System all format and reinstall the system using SST or USB copyir.com
E730-C000 Initialization error
An error, such as failure in memory retrieval at startup, occurs 1 copyir.com System all format and installation copyir.com
2 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E730-C001 HDD access error
An error occurs when accessing to the HDD 1 copyir.com Start in safe mode to format the HDD (all the data in the HDD is erased) copyir.com
2 copyir.com Replace the HDD copyir.com
3 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E731-3000 Error in Main Controller PCB
Unable to recognize the Surf board 1 copyir.com Check connection of Main Controller PCB copyir.com
2 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E731-3001 Error in Main Controller PCB
Failure in Surf initialization 1 copyir.com Check connection of Main Controller PCB copyir.com
2 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E731-3002 Error in Main Controller PCB
Failure in Surf initialization 1 copyir.com Check connection of Main Controller PCB copyir.com
2 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E731-3015 Error in Main Controller PCB
Although it works normally at the software side, there is no video data into CL1-G 1 copyir.com Check connection of Main Controller PCB copyir.com
2 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E732-0010 Scanner communication error
Vertical Synchronizing signal detection error 1 copyir.com Check the connection of the Connector with the Reader copyir.com 2 copyir.com Check the power of the Reader (check if the initialization operation is executed at startup) copyir.com 3 copyir.com Replace the Reader Relay PCB copyir.com 4 copyir.com Replace the Main Controller PCB copyir.com
E740-0002 Ethernet Board error
Invalid MAC address 1 copyir.com Replace the LAN card
E740-0003 Ethernet Board error
Invalid MAC address 1 copyir.com Replace the LAN card
E743-0000 DDI communication error
SCI error, reception data NG, reception timeout, SEQ timeout error 1 copyir.com Turn OFF and then ON the power copyir.com
2 copyir.com Check connection of the cable between the Reader and the Controller copyir.com
3 copyir.com Check voltage (+24V and +12V) on the Reader Controller PCB copyir.com
4 copyir.com Replace the Reader Controller PCB (PCB3) copyir.com
5 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E744 Language file error
E746-0021 Engine ID error
Self-check error of Image Analysis Board (HW board used for PCAM) 1 copyir.com Replace the Image Analysis Board (HW board used for PCAM) copyir.com
2 copyir.com As a temporary measure, remove the Image Analysis Board and get in service mode:
COPIER > OPTION > LCNS-TR > ST-JBLK (Lv2); set ST-JBLK from 1 to 0, and turn OFF and then ON the power copyir.com
E746-0022 Engine ID error
Wrong version of Image Analysis Board 1 copyir.com Update the firmware of the Image Analysis Board copyir.com
2 copyir.com As a temporary measure, remove the Image Analysis Board and get in service mode:
COPIER > OPTION > LCNS-TR > ST-JBLK (Lv2); set ST-JBLK from 1 to 0, and turn OFF and then ON the power copyir.com
E746-0023 Engine ID error
No reply from the Image Analysis Board 1 copyir.com Check if the Image Analysis Board is correctly installed copyir.com
2 copyir.com Turn OFF and then ON the power copyir.com
3 copyir.com If the problem is not fixed, replace the Option Board copyir.com
4 copyir.com As a temporary measure, remove the Image Analysis Board and get in service mode:
COPIER > OPTION > LCNS-TR > ST-JBLK (Lv2); set ST-JBLK from 1 to 0, and turn OFF and then ON the power copyir.com
E746-0024 Engine ID error
Operation error of the Image Analysis Board 1 copyir.com Turn OFF and then ON the power copyir.com
2 copyir.com If the problem is not fixed, replace the Image Analysis Board copyir.com
3 copyir.com As a temporary measure, remove the Image Analysis Board and get in service mode:
(Lv2) COPIER > OPTION > LCNS-TR > ST-JBLK ; set ST-JBLK from 1 to 0, and turn OFF and then ON the power copyir.com
E746-0031 Engine ID error
Hardware error 1 copyir.com Turn OFF and then ON the power copyir.com
2 copyir.com Replace the TPM PCB copyir.com
E746-0032 Engine ID error
TPM key mismatch Format the system
Use SST or USB memory to format the HDD, and then execute downloading of the system software copyir.com See Chapter 6 Upgrading for details copyir.com For reference, the method using USB memory is shown below:
1 copyir.com Prepare USB memory in which the system software was registered copyir.com
E746-0033 Engine ID error
Mismatched data in the TPM Recovery is available if backup of the TPM has been executed copyir.com
1 copyir.com Connect the USB memory in which the TPM key is saved copyir.com
2 copyir.com Management Settings > Data Management > TPM Settings; click [Restore TPM key] copyir.com
3 copyir.com Enter the password that was specified at the time of backup work copyir.com
4 copyir.com Once the restore completion screen is displayed, click [OK] and remove the USB memory, and then turn OFF and ON the main power switch copyir.com
When backup of the TPM key is not executed
System format is necessary copyir.com
Use SST or USB memory to format the HDD, and then download the system software copyir.com
E746-0034 TPM auto recovery error
An error occurs when clearing the HDD while the TPM setting is ON The symptom is recovered by turning OFF and then ON the power
E746-0035 TPM version error
TPM which cannot be used in this machine was installed copyir.com Install the supported TPM copyir.com
E747-1201 PDL rendering error
Image processing IC error 1 copyir.com Turn OFF and then ON the power (send the data to Inc because running the data which generated an error code causes another error code) copyir.com
2 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E748-2010 Flash PCB error
Unable to find IPL (startup program) Replace the Flash PCB and install the system using SST or USB
E748-2021 Main Controller PCB access error
Necessary H/W on Main Controller PCB is not detected 1 copyir.com Clean the terminal of Main Controller PCB, and remove and then install Main Controller PCB copyir.com
2 copyir.com Replace Main Controller PCB (PCB2) copyir.com
E748-2023 Main Controller PCB access error
Unable to initialize memory DDR2-SDRAM at the Main Controller PCB 1 copyir.com Clean the terminal of DDR2-SDRAM, and remove and then install the DDR2-SDRAM copyir.com
2 copyir.com Replace the DDR2-SDRAM copyir.com
E748-2024 Main Controller PCB access error
The CPU at the Main Controller PCB failed to complete initialization 1 copyir.com Clean the terminal of DDR2-SDRAM, and remove and then install the DDR2-SDRAM copyir.com
2 copyir.com Check power state of Main Controller PCB and check around the connector copyir.com
3 copyir.com Replace Main Controller PCB copyir.com
E748-9000 System error Contact the service company office
E749-0002 Rebooting instruction due to change of MEAP configuration
There is a change in configuration that requires turning OFF and then ON the power The symptom is recovered by turning OFF and then ON the power
E749-0003 Booting instruction due to change in mAccele configuration
There is a change in configuration that requires turning OFF and then ON the power The symptom is recovered by turning OFF and then ON the power
E749-0005 Booting instruction due to change in hardware configuration
There is a change in configuration that requires turning OFF and then ON the power The symptom is recovered by turning OFF and then ON the power
E749-0006 Restart direction due to configuration change copyir.com
The option such as the Finisher and ADF was installed or removed when all of following conditions were met and the machine configuration is changed when the main power switch is turned ON copyir.com
– Settings/Registration > Preferences > Timer/Energy Settings > Quick Startup at Power-on > ON
– The Main Power Switch is turned OFF
– The power plug of the machine is connected to the output copyir.com It is recovered by turning OFF and then ON the main power copyir.com
CAUTION
This machine provides power to some PCBs even when in the main power OFF status copyir.com
The power supply is not completely OFF by just turning OFF the main power switch and therefore, the machine is unable to detect a configuration change copyir.com
When disconnecting and then connecting a connector, always disconnect the power plug copyir.com
Refer to the Service Manual > Chapter 2 > External and Controls > Quick Startup for details copyir.com
E753-0001 Downloading error
Firmware update error
This symptom occurs when trying to update the firmware of an option that is not installed 1 copyir.com Check the log to identify the location of the download error copyir.com
Check if the target option is installed copyir.com
When the target option is not installed:
-> The symptom is recovered by turning OFF and then ON the power (because there is nothing to update)
When the target option is installed:
-> Check if the target option is properly installed and see if the software to download is for the correct target option, and then execute downloading again copyir.com
E804-0000 Power Supply Cooling Fan (FM4) error
When detecting a failure of the Power Supply Cooling Fan (FM4) copyir.com 1 copyir.com Check the connector connection between the Power Supply Cooling Fan (FM4) and the AC Driver PCB (PCB4) copyir.com
2 copyir.com Replace the Power Supply Cooling Fan (FM4) copyir.com
E805-0000 Heat Exhaust Fan (Rear) (FM6) error
The lock signal was detected for 5 copyir.com0 seconds while the Heat Exhaust Fan (Rear) (FM6) was being stopped copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Heat Exhaust Fan (Rear) (FM6) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Heat Exhaust Fan (Rear) (FM6) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E805-0001 Heat Exhaust Fan (Rear) (FM6) rotation error
The lock signal was not detected for 5 copyir.com0 seconds while the Heat Exhaust Fan (Rear) (FM6) was being driven copyir.com
*The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Heat Exhaust Fan (Rear) (FM6) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Heat Exhaust Fan (Rear) (FM6) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E805-0002 Heat Exhaust Fan (Front) (FM5) error
The lock signal was detected for 5 copyir.com0 seconds while the Heat Exhaust Fan (Front) (FM5) was being stopped copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Heat Exhaust Fan (Front) (FM5) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Heat Exhaust Fan (Front) (FM5) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E805-0003 Heat Exhaust Fan (Front) (FM5) rotation error
The lock signal was not detected for 5 copyir.com0 seconds while the Heat Exhaust Fan (Front) (FM5) was being driven copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Heat Exhaust Fan (Front) (FM5) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Heat Exhaust Fan (Front) (FM5) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E820-0000 Developing Cooling Fan (Front) (FM7) error
The lock signal was detected for 5 copyir.com0 seconds while the Developing Cooling Fan (Front) (FM7) was being stopped copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Developing Cooling Fan (Front) (FM7) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Developing Cooling Fan (Front) (FM7) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E820-0001 Developing Cooling Fan (Front) (FM7) rotation error
The lock signal was not detected for 5 copyir.com0 seconds while the Developing Cooling Fan (Front) (FM7) was being driven copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Developing Cooling Fan (Front) (FM7) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Developing Cooling Fan (Front) (FM7) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E820-0002 Developing Cooling Fan (Rear) (FM8) error
The lock signal was detected for 5 copyir.com0 seconds while the Developing Cooling Fan (Rear) (FM8) was being stopped copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Developing Cooling Fan (Rear) (FM8) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Developing Cooling Fan (Rear) (FM8) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E820-0003 Developing Cooling Fan (Rear) (FM8) rotation error
The lock signal was not detected for 5 copyir.com0 seconds while the Developing Cooling Fan (Rear) (FM8) was being driven copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Developing Cooling Fan (Rear) (FM8) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Developing Cooling Fan (Rear) (FM8) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E822-0000 Delivery Cooling Fan (Front) (FM3) error
The lock signal was detected for 5 copyir.com0 seconds while the Delivery Cooling Fan (Front) (FM3) was being stopped copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Delivery Cooling Fan (Front) (FM3) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Delivery Cooling Fan (Front) (FM3) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E822-0001 Delivery Cooling Fan (Front) (FM3) rotation error
The lock signal was not detected for 5 copyir.com0 seconds while the Delivery Cooling Fan (Front) (FM3) was being driven copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Delivery Cooling Fan (Front) (FM3) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Delivery Cooling Fan (Front) (FM3) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E822-0003 Delivery Cooling Fan (Center) (FM2) rotation error
The lock signal was not detected for 5 copyir.com0 seconds while the Delivery Cooling Fan (Center) (FM2) was being driven copyir.com *The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Delivery Cooling Fan (Center) (FM2) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Delivery Cooling Fan (Center) (FM2) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E822-0005 Delivery Cooling Fan (Rear) (FM1) rotation error
The lock signal was not detected for 5 copyir.com0 seconds while the Delivery Cooling Fan (Rear) (FM1) was being driven copyir.com
*The same status was detected again after executing an error retry copyir.com 1 copyir.com Check the connector connection between the Delivery Cooling Fan (Rear) (FM1) and the DC Controller PCB (PCB1) copyir.com
2 copyir.com Replace the Delivery Cooling Fan (Rear) (FM1) copyir.com
3 copyir.com Replace the DC Controller PCB (PCB1) copyir.com
E880-0001 Controller Fan error
Lock of Controller Fan is detected Check if the connector is connected
If the connector is OK, replace Controller Fan copyir.com
E881-0001 CPU abnormal temperature rising error
Abnormal temperature of the Main Controller CPU 1 copyir.com Send cold air to the device copyir.com 2 copyir.com If there is a shielding object around the inlet, remove it to secure enough space copyir.com 3 copyir.com Check the fan, and remove dust or replace the fan if it has an abnormality such as abnormal sound copyir.com 4 copyir.com Replace the Main Controller PCB copyir.com
E996-0071 Frequent error avoidance jam (ADF) Depending on the setting of JM-ERR-R in service mode, “010071” jam is displayed as an error copyir.com
Collect log and contact to the sales companies copyir.com
To cancel the setting, select COPIER> OPTION> FNC-SW> JM-ERR-R, and set JM-ERR-R to 0
E996-0CA0 Frequent error avoidance jam (PRINTER) Make “000CA0” jam to be displayed as an error by setting JM-ERR-D in service mode copyir.com
Collect log and contact to the sales companies copyir.com
To cancel the setting, select COPIER> OPTION> FNC-SW> JM-ERR-D, and set JM-ERR-D to 0
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.