کدها و خطاهای فتوکپی ریکو آفیشیو 3045

کدها و خطاهای فتوکپی ریکو آفیشیو 3045

2 SC CODE DESCRIPTIONS

NOTE: This is a list of فتوکپی ریکو آفیشیو 3045 new and revised SC codes for فتوکپی ریکو آفیشیو 3045 B079 (35 cpm) and B082 (45 cpm) machines. For details about oفتوکپی ریکو آفیشیو 3045r SC codes please refer to Service Manual of فتوکپی ریکو آفیشیو 3045 previous models.

Code No.

Symptom

Possible Cause

320

(Deleted)

C

Polygon motor error

335

(New)

C Polygonal Mirror Motor Error 1: ON Timeout
  • I/F harness of فتوکپی ریکو آفیشیو 3045 polygonal mirror motor disconnected or defective.
  • Polygonal mirror motor or polygonal mirror motor driver defective.
  • Polygonal mirror motor drive pulse is not output incorrectly.
  • GABIC cannot monitor XSCRDY signal.
فتوکپی ریکو آفیشیو 3045 XSCRDY signal is not issued (LOW: Active) within 25 s after فتوکپی ریکو آفیشیو 3045 polygonal mirror motor switches on.

336

(New)

C Polygonal Mirror Motor Error 2: OFF Timeout
  • I/F harness of فتوکپی ریکو آفیشیو 3045 polygonal mirror motor disconnected or defective.
  • Polygonal mirror motor or polygonal mirror motor driver defective.
  • Polygonal mirror motor drive pulse is not output incorrectly.
  • GABIC cannot monitor XSCRDY signal.
فتوکپی ریکو آفیشیو 3045 XSCRDY signal is not issued (HIGH: Inactive) within 2 s after فتوکپی ریکو آفیشیو 3045 polygonal mirror motor switches off.

337

(New)

C Polygonal Mirror Motor Error 3: XSCRDY Signal Error
  • I/F harness of فتوکپی ریکو آفیشیو 3045 polygonal mirror motor disconnected or defective.
  • Polygonal mirror motor or polygonal mirror motor driver defective.
  • Polygonal mirror motor drive pulse is not output incorrectly.
  • GABIC cannot monitor XSCRDY signal.
فتوکپی ریکو آفیشیو 3045 XSCRDY is not issued (HIGH: Inactive) after فتوکپی ریکو آفیشیو 3045 polygonal mirror motor has been rotating normally for 600 ms.

338

(New)

C Polygonal Mirror Motor Error 4: Unstable Timeout
  • I/F harness of فتوکپی ریکو آفیشیو 3045 polygonal mirror motor disconnected or defective.
  • Polygonal mirror motor or polygonal mirror motor driver defective.
  • Polygonal mirror motor drive pulse is not output incorrectly.
  • GABIC cannot monitor XSCRDY signal.
فتوکپی ریکو آفیشیو 3045 XSCRDY signal is detected LOW) (Active) after فتوکپی ریکو آفیشیو 3045 polygonal mirror motor switches on, but فتوکپی ریکو آفیشیو 3045 signal is not detected LOW after 1 s has elapsed, and not detected after anoفتوکپی ریکو آفیشیو 3045r 500 ms has elapsed.

450

(New)

C Feed Development Motor Error
  • Motor lock caused by overload.
  • Motor driver defective.
فتوکپی ریکو آفیشیو 3045 PLL lock signal remains LOW for 2 s while فتوکپی ریکو آفیشیو 3045 feed development motor is operating.

520

(New)

C Fusing/Feed-Out Motor Error
فتوکپی ریکو آفیشیو 3045 PLL lock signal remains LOW for 2 s while فتوکپی ریکو آفیشیو 3045 feed development motor is operating.
  • Motor lock caused by overload.
  • Motor driver defective.

SERVICE CALL CONDITIONS

Code No.

Symptom

Possible Cause

818

(New)

B Watch Dog Error
While فتوکپی ریکو آفیشیو 3045 system program is running, a bus hold or interrupt program goes into an eternal loop, preventing any oفتوکپی ریکو آفیشیو 3045r programs from executing.
  • System program defective
  • Controller board defective
  • Peripheral device malfunction

838

(Deleted)

B Self-diagnostic Error: Clock Generator

840

(New)

C Self-Diagnostic Error 1: EEPROM Access Error
  • EEPROM defective
  • EEPROM worn out

During input/output with فتوکپی ریکو آفیشیو 3045 EEPROM, one of فتوکپی ریکو آفیشیو 3045 following errors occurred:

  • A read error occurred, فتوکپی ریکو آفیشیو 3045n continued after 3 retries.
  • Write error occurred.

841

(New)

C Self-Diagnostic Error 2: EEPROM Read/Write Data Error • فتوکپی ریکو آفیشیو 3045 data is being written into فتوکپی ریکو آفیشیو 3045 3 designated errors differently
فتوکپی ریکو آفیشیو 3045 values of فتوکپی ریکو آفیشیو 3045 data written and mirrored in 3 errors are all detected as not matching..

853

(New)

B Wireless LAN Error: Card Error 1 • Wireless LAN card not inserted into فتوکپی ریکو آفیشیو 3045 wireless LAN board
فتوکپی ریکو آفیشیو 3045 wireless LAN board can be accessed, but فتوکپی ریکو آفیشیو 3045 wireless LAN card (IEEE 802.11b or Bluetooth) cannot access فتوکپی ریکو آفیشیو 3045 board.

854

(New)

B Wireless LAN Error Card Error 2 • Wireless LAN card has been removed
فتوکپی ریکو آفیشیو 3045 board that holds فتوکپی ریکو آفیشیو 3045 wireless LAN card can be accessed, but فتوکپی ریکو آفیشیو 3045 wireless LAN card

(802.11b/Bluetooth) itself cannot be accessed while فتوکپی ریکو آفیشیو 3045 machine is operating

855

(New)

B Wireless LAN Error 3: Card Error 3
  • Wireless LAN card defective
  • Wireless card connection not tight
An error is detected for فتوکپی ریکو آفیشیو 3045 wireless LAN card (802.11b or Bluetooth).

856

(New)

Wireless LAN Error 4: Board
  • Wireless LAN card board defective
  • PCI connector loose
An error is detected for فتوکپی ریکو آفیشیو 3045 wireless LAN card (802.11b or Bluetooth).

857

(New)

B USB I/F Error • فتوکپی ریکو آفیشیو 3045 USB driver can generate three types of errors: RX, CRC, and STALL errors. Only فتوکپی ریکو آفیشیو 3045 STALL error can generate this SC code.
فتوکپی ریکو آفیشیو 3045 USB driver is unstable and generated an error. فتوکپی ریکو آفیشیو 3045 USB I/F cannot be used.

870

(New)

B Address Book Data Error
  • Software defective
  • HDD defective
Address book data stored on فتوکپی ریکو آفیشیو 3045 hard disk was detected as abnormal when it was accessed from eiفتوکپی ریکو آفیشیو 3045r فتوکپی ریکو آفیشیو 3045 operation panel or فتوکپی ریکو آفیشیو 3045 network.

SERVICE CALL CONDITIONS

Code No.

Symptom

Possible Cause

871

(New)

B FCU Flash ROM Error
  • Flash ROM device defective
  • Replace flash ROM on فتوکپی ریکو آفیشیو 3045 MBU
فتوکپی ریکو آفیشیو 3045 address book written into فتوکپی ریکو آفیشیو 3045 flash ROM mounted on فتوکپی ریکو آفیشیو 3045 FCU is detected as defective.

880

(New)

B MLB Error • MLB defective
A request for access to فتوکپی ریکو آفیشیو 3045 MLB (Media Link Board) was not answered within فتوکپی ریکو آفیشیو 3045 specified time.

920

(New)

B Printer Error 1
An internal application error was detected and operation cannot continue.
  • Software defective
  • Insufficient memory

925

(New)

B Network File Error • NIA
NIA

964

(Revised)

C Scanner Start Error • Software defective
During scanned image processing, anoفتوکپی ریکو آفیشیو 3045r command to start scanning was received.

992

(New)

A Unexpected Software Error
  • Software defective
  • An error undetectable by any oفتوکپی ریکو آفیشیو 3045r SC code occurred
Software encountered an unexpected operation not defined under any SC code.

995

(New)

A Machine Type Information Error فتوکپی ریکو آفیشیو 3045 B079 (35 cpm) and B082 (45 cpm) use فتوکپی ریکو آفیشیو 3045 same controller board, but فتوکپی ریکو آفیشیو 3045 DIP SW settings must be set correctly for فتوکپی ریکو آفیشیو 3045 machine speed. For details, see Section 3. Replace and Adjustment.
After فتوکپی ریکو آفیشیو 3045 machine is powered on, a mismatch is detected between فتوکپی ریکو آفیشیو 3045 CPM information sent from فتوکپی ریکو آفیشیو 3045 controller to فتوکپی ریکو آفیشیو 3045 engine and فتوکپی ریکو آفیشیو 3045 CPM information specified by فتوکپی ریکو آفیشیو 3045 DIP SW settings.

ELECTRICAL COMPONENT DEFECTS

Component (Symbol)

CN

Condition

Symptom

Scanner Home

Position (S1)

504-5(SIB) Open SC121 is displayed.
Shorted SC120 is displayed.
Platen Cover (S2) 504-8 (SIB) Open APS and ARE do not function properly.
Shorted No symptom.
Original Width (S3) 505-3, 4

(SIB)

Open CPU cannot detect فتوکپی ریکو آفیشیو 3045 original size properly. APS and ARE do not function correctly.
Shorted
Original Length-1 (S4) 505-8,9

(SIB)

Open CPU cannot detect فتوکپی ریکو آفیشیو 3045 original size properly. APS and ARE do not function correctly.
Shorted
Original Length-2 (S5) 505-13

(SIB)

Open CPU cannot detect فتوکپی ریکو آفیشیو 3045 original size properly. APS and ARE do not function correctly.
Shorted
LD Unit Home Position (S6) 204-B2

(IOB)

Open SC328 is displayed when فتوکپی ریکو آفیشیو 3045 laser beam pitch is changed.
Shorted SC327 is displayed when فتوکپی ریکو آفیشیو 3045 laser beam pitch is changed.
Toner Density (TD) (S7) 222-5  (IOB) Open فتوکپی ریکو آفیشیو 3045 add toner indicator blinks even if فتوکپی ریکو آفیشیو 3045re is toner in فتوکپی ریکو آفیشیو 3045 development unit.
Shorted SC390-01 is displayed.
Paper Exit (S8) 202-B2

(IOB)

Open فتوکپی ریکو آفیشیو 3045 Paper Jam indicator will light whenever a copy is made.
Shorted فتوکپی ریکو آفیشیو 3045 Paper Jam indicator lights even if فتوکپی ریکو آفیشیو 3045re is no paper.
Registration (S9) 224-B2

(IOB)

Open فتوکپی ریکو آفیشیو 3045 Paper Jam indicator lights even if فتوکپی ریکو آفیشیو 3045re is no paper.
Shorted فتوکپی ریکو آفیشیو 3045 فتوکپی ریکو آفیشیو 3045 Paper Jam indicator will light whenever a copy is made.
Image Density (ID) (S10) 203-5

(IOB)

Open SC350-03 is displayed after copying.
Shorted SC350-01 is displayed after copying.
Upper Paper Height (S11) 220-2

(IOB)

Open Add Paper is displayed even if فتوکپی ریکو آفیشیو 3045re is paper. If this condition occurred four times, SC501-02 will be displayed.
Shorted SC501-01 is displayed.
Lower Paper Height (S12) 214-2

(IOB)

Open Add Paper is displayed even if فتوکپی ریکو آفیشیو 3045re is paper. If this condition occurred four times, SC502-02 will be displayed.
Shorted SC502-01 is displayed.
Upper Paper End (S13) 220-8

(IOB)

Open فتوکپی ریکو آفیشیو 3045 Paper End indicator lights even if paper is placed in فتوکپی ریکو آفیشیو 3045 upper paper tray.
Shorted فتوکپی ریکو آفیشیو 3045 Paper End indicator does not light even if فتوکپی ریکو آفیشیو 3045re is no paper in فتوکپی ریکو آفیشیو 3045 upper paper tray.

4.2 ELECTRICAL COMPONENT DEFECTS

4.2.1 SENSORS

BLOWN FUSE CONDITIONS

Component (Symbol)

CN

Condition

Symptom

Lower Paper End (S14) 214-8

(IOB)

Open فتوکپی ریکو آفیشیو 3045 Paper End indicator lights even if paper is placed in فتوکپی ریکو آفیشیو 3045 lower paper tray.
Shorted فتوکپی ریکو آفیشیو 3045 Paper End indicator does not light even if فتوکپی ریکو آفیشیو 3045re is no paper in فتوکپی ریکو آفیشیو 3045 lower paper tray.
Upper Relay (S15) 220-5

(IOB)

Open فتوکپی ریکو آفیشیو 3045 Paper Jam indicator will light whenever a copy is made.
Shorted فتوکپی ریکو آفیشیو 3045 Paper Jam indicator lights even if فتوکپی ریکو آفیشیو 3045re is no paper.
Lower Relay (S16) 214-5

(IOB)

Open فتوکپی ریکو آفیشیو 3045 Paper Jam indicator will light whenever a copy is made.
Shorted فتوکپی ریکو آفیشیو 3045 Paper Jam indicator lights even if فتوکپی ریکو آفیشیو 3045re is no paper.
Transfer Belt Position (S19) 202-A10

(IOB)

Open No symptom
Shorted SC403 is displayed

4.2.2 SWITCHES

Component (Symbol)

CN

Condition

Symptom

Right Lower Cover (SW1) 216-4

(IOB)

Open Doors/Covers Open is displayed even if فتوکپی ریکو آفیشیو 3045 right lower cover is closed.
Shorted فتوکپی ریکو آفیشیو 3045 LCD goes blank when فتوکپی ریکو آفیشیو 3045 lower cover is opened.
Main (SW3) 102-1~4 (PSU) 107-1 Open فتوکپی ریکو آفیشیو 3045 machine does not turn on.
Shorted فتوکپی ریکو آفیشیو 3045 machine does not turn off.
Front Cover Safety (SW4) 107-1

(PSU)

Open Doors/Covers Open is displayed even if فتوکپی ریکو آفیشیو 3045 front cover is closed.
Shorted Doors/Covers Open is not displayed even if فتوکپی ریکو آفیشیو 3045 front cover is opened.

4.3 BLOWN FUSE CONDITIONS

Fuse

Rating

Symptom at power on

115V

210 ~ 230V

Power Su pply Board

FU1

6.3A / 125V 6.3A / 250V Doors/Covers Open is displayed

FU2

6.3A / 125V 6.3A / 250V Doors/Covers Open for فتوکپی ریکو آفیشیو 3045 finisher is displayed

FU3

6.3A / 125V 6.3A / 250V Paper end condition

FU5

6.3A / 125V 6.3A / 250V SC302, or SC403, or SC405 displayed

FU6

3.15A/125V 3.15A/250V

FU9

4A/125V 4A/250V

FU101

15A / 125V No response

FU102

10A / 125V 5A / 250V No response

FU103

2A / 125V 1A / 250V Normal operation (optional heaters do not work)

LEDS

4.4 LEDS

BICU LED Sequences

LED 101 (Green)

LED 102 (Red)

LED 103 (Orange)

Normal Operation Flashes Off Flashes
System Startup Flashes On (1~2s) فتوکپی ریکو آفیشیو 3045n Off Flashes
Firmware Update: Normal Execution Flashes On Flashes
Firmware Update: Error Flashes Flashes Flashes
Firmware Update: Normal End Flashes Off Flashes
Energy Save Mode Off Off Off

Controller LED Sequences

LED 1 (Red)

LED 2 (Red)

System Startup (including Self-Diagnostics) On Off
Self-Diagnostic Error On On
Normal Operation Flashes Off
Firmware Update: Normal Execution Flashes Flashes
Firmware Update: Error Off Off
Firmware Update: Normal End On On

NOTE: LED 1 monitors Data Bus Bit 14, LED 2 monitors Data Bus Bit 15.

4.5 TEST POINTS

Controller Board

Number

Monitored Signal

TP1

GND

TP3

GND

TP6

GND

TP8

DB0 RXD

TP9

DB0 TXD

TP10

GND

TP11

+5VE

TP12

GND

TP13

+5V

TP14

+5VE

TP15

GND

TP16

R_FGATE

TP17

W_FGATE

اشتراک گذاری در:

پست های مرتبط

دیدگاهتان را بنویسید

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

جستجو در مطالب

سوالی دارید؟

برای آگاهی از راه های ارتباط با ما، بر روی دکمه زیر کلیک کنید

مطالب جدید ...

در خبرنامه ما عضو شوید