لمینت MKP
1402-06-04
Menu
E001-0000 Abnormality high temperature error of the fixing unit
Detect high temperature by the main thermistor (software) copyir.com Software detects that the temperature detected by the main thermistor is abnormally high (above 260 deg C) for 500 ms continuously copyir.com Replace the fixing unit, Replace the main power supply PCB, Replace the DC controller PCB To recover from the error: In service mode COPIER>FUNCTION> CLEAR>ERR
E001-0001 Abnormality high temperature error of the fixing unit
Detect high temperature by the sub thermistor (software) copyir.com Software detects that the temperature detected by the sub thermistor is abnormally high (above 260 deg C) for 500 ms continuously copyir.com Replace the fixing unit, Replace the main power supply PCB, Replace the DC controller PCB To recover from the error: In service mode COPIER>FUNCTION> CLEAR>ERR
E001-0003 Abnormality high temperature error of the fixing unit
Detect high temperature by the sub thermistor (hardware) copyir.com Hardware detects that the temperature detected by the contact type thermistor is abnormally high (above 230 deg C) copyir.com Replace the fixing unit, Replace the main power supply PCB, Replace the DC controller PCB To recover from the error: In service mode COPIER>FUNCTION> CLEAR>ERR
E003-0000 Error in the low temperature of the fixing unit
Detects the temperature detected by the main thermistor is abnormally low (below 120 deg C) for 1 sec continuously after passing 20 sec from turning ON the fixing heater copyir.com Check the connection of the main thermistor/thermal switch copyir.com Check open circuit of heater copyir.com Replace the cover switch copyir.com Replace the fixing unit copyir.com Replace the main power supply PCB copyir.com Replace the DC controller PCB copyir.com Clear the error in service mode: COPIER > FUNCTION > CLEAR > ERR copyir.com
E003-0001 Error in the low temperature of the fixing unit
Detects the temperature detected by the sub thermistor is abnormally low (below 70 deg C) for 1 sec continuously while adjusting print temperature copyir.com Check on connection of the sub thermistor/thermo switch, Replace the fixing unit, Check on a break in the heater, Replace the cover switch, Replace the main power supply PCB, Replace the DC controller PCB To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR
E003-0002 Error in the low temperature of the fixing unit
Detects the abnormally low temperature (open circuit) when turning ON the fixing heater copyir.com Clear the error in service mode: COPIER > FUNCTION > CLEAR > ERR copyir.com
E004-0000 Thermistor is not connected
During walm-up rotation, the thermistor connection signal (FUSER CNCTX) is open copyir.com – Confirm the cable connection – Replace the cable exchange, and established – Replace the fixing unit – Replace the DC controller PCB copyir.com
E009-0001 Error in pressure/release of fixing film unit
In case that the output of fixing automatic pressure phase sensor is not changed although rotating/reversing the fixing motor Check the pressure/release mechanism copyir.com Check the connection of the connector copyir.com Replace the motor copyir.com
E012-0000 Drum/ITB motor error
Lock of the motor fails to be detected 3 sec or more after the motor starts to operate copyir.com Check on connection of the connector, Replace the motor
E013-0001 Error in the waste toner motor
Detects the fault in the waste toner motor Replace the waste toner motor copyir.com
E013-0002 Error in the waste toner motor
Indicates that the waste toner motor does not rotate due to the open circuit copyir.com Replace the waste toner motor copyir.com Replace the DC controller PCB copyir.com
E015-0000 Error in the registration/multifeeder motor
Indicates that the signal indicates the motor rotates with the target speed is not sent to the port after passing more than 3 sec from the startup of the motor copyir.com Check on connection of the connector, Replace the motor
E020-0010 Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is higher than the upper limit of the target although setting it as the minimum when initializing Yellow ATR copyir.com Clean the ATR sensor window copyir.com Check the mounting of the developing assembly copyir.com Check the ATR sensor open circuit copyir.com Replace the ATR sensor copyir.com
E020-0011 Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is higher than the upper limit of the target although setting it as the minimum when initializing Magenta ATR copyir.com Clean the ATR sensor window copyir.com Check the mounting of the developing assembly copyir.com Check the ATR sensor open circuit copyir.com Replace the ATR sensor copyir.com
E020-0012 Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is higher than the upper limit of the target although setting it as the minimum when initializing Cyan ATR copyir.com Clean the ATR sensor window copyir.com Check the mounting of the developing assembly copyir.com Check the ATR sensor open circuit copyir.com Replace the ATR sensor copyir.com
E020-0013 Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is higher than the upper limit of the target although setting it as the minimum when initializing Black ATR copyir.com Clean the ATR sensor window copyir.com Check the mounting of the developing assembly copyir.com Check the ATR sensor open circuit copyir.com Replace the ATR sensor copyir.com
E020-0020 Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Yellow ATR copyir.com Clean the ATR sensor window copyir.com Check the mounting of the developing assembly copyir.com Check the ATR sensor open circuit copyir.com Replace the ATR sensor copyir.com
E020-0021 Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Magenta ATR copyir.com Clean the ATR sensor window copyir.com Check the mounting of the developing assembly copyir.com Check the ATR sensor open circuit copyir.com Replace the ATR sensor copyir.com
E020-0021 Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Magenta ATR copyir.com Clean the ATR sensor window copyir.com Check the mounting of the developing assembly copyir.com Check the ATR sensor open circuit copyir.com Replace the ATR sensor copyir.com
E020-0022 Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Cyan ATR copyir.com Clean the ATR sensor window copyir.com Check the mounting of the developing assembly copyir.com Check the ATR sensor open circuit copyir.com Replace the ATR sensor copyir.com
E020-0023 Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Black ATR copyir.com Clean the ATR sensor window copyir.com Check the mounting of the developing assembly copyir.com Check the ATR sensor open circuit copyir.com Replace the ATR sensor copyir.com
E020-0100 Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Yellow is higher than the upper limit copyir.com Check the toner leakage from the toner buffer block within the developing assembly copyir.com Replace the patch image reading sensor copyir.com
E020-0101 Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Magenta is higher than the upper limit copyir.com Check the toner leakage from the toner buffer block within the developing assembly copyir.com Replace the patch image reading sensor copyir.com
E020-0102 Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Cyan is higher than the upper limit copyir.com Check the toner leakage from the toner buffer block within the developing assembly copyir.com Replace the patch image reading sensor copyir.com
E020-0103 Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Black is higher than the upper limit copyir.com Check the toner leakage from the toner buffer block within the developing assembly copyir.com Replace the patch image reading sensor copyir.com
E020-0200 Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Yellow is lower than the lower limit copyir.com Check the toner leakage from the toner buffer block within the developing assembly copyir.com Replace the patch image reading sensor copyir.com
E020-0201 Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Magenta is lower than the lower limit copyir.com Check the toner leakage from the toner buffer block within the developing assembly copyir.com Replace the patch image reading sensor copyir.com
E020-0202 Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Cyan is lower than the lower limit copyir.com Check the toner leakage from the toner buffer block within the developing assembly copyir.com Replace the patch image reading sensor copyir.com
E020-0203 Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Black is lower than the lower limit copyir.com Check the toner leakage from the toner buffer block within the developing assembly copyir.com Replace the patch image reading sensor copyir.com
E021-0000 Developing motor error
Indicates that the signal indicates the motor rotates with the target speed is not sent to the port after passing more than 3 sec from the startup of the motor copyir.com Check on connection of the developing motor and the DC controller PCB, Replace the DC controller PCB, Replace the developing moto
E025-0000 Error in the toner motor
Indicates an error of Y developing assembly toner supply Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0001 Error in the toner motor
Indicates an error of M developing assembly toner supply Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0002 Error in the toner motor
Indicates an error of C developing assembly toner supply Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0003 Error in the toner motor
Error of Bk developing assembly toner supply Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0100 Error in the toner motor
Y buffer supply error Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0101 Error in the toner motor
M buffer supply error Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0102 Error in the toner motor
C buffer supply error Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0103 Error in the toner motor
Bk buffer supply error Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E032-0001 The counter of the NE controller fails to operate copyir.com
A break in the count pulse signal is detected copyir.com Check on a break in the cable
E045-0000 OHP sensor error
The sampling data measured during initial multiple rotations is lower than the specific level copyir.com Replace the OHP sensor
E067-0101 High voltage-related error (Primary transfer)
The first detected current of primary transfer ATVC is the threshold or more copyir.com Check on the primary transfer roller spring, Clean the position where the primary transfer roller contacts, Replace the primary transfer roller, Replace the drum unit Check a value of COPIER> DISPLAY> MISC> DRM-LIFE, and replace the drum unit if the value is near 100 because the drum may have reached its life expectancy copyir.com
E067-0102 High voltage-related error (Primary transfer)
The two detected currents of primary transfer ATVC are both the threshold or less copyir.com Check on the primary transfer roller spring, Clean the position where the primary transfer roller contacts, Replace the primary transfer roller, Replace the drum unit Check a value of COPIER> DISPLAY> MISC> DRM-LIFE, and replace the drum unit if the value is near 100 because the drum may have reached its life expectancy copyir.com
E067-0103 High voltage-related error (Primary transfer)
The two detected currents of primary transfer ATVC are the same each other copyir.com Check on the primary transfer roller spring, Clean the position where the primary transfer roller contacts, Replace the primary transfer roller, Replace the drum unit Check a value of COPIER> DISPLAY> MISC> DRM-LIFE, and replace the drum unit if the value is near 100 because the drum may have reached its life expectancy copyir.com
E100-0000 BD error
Lock of the BD control fails while rotation of the polygon motor is stable copyir.com Check on connection between the laser scanner unit and the DC controller PCB, Check on 24V line fuse, Replace the laser scanner unit
E110-0000 Error in polygon motor
BD control is not locked when 5 sec passed after the activation of polygon motor copyir.com Check on connection between the laser scanner unit and the DC controller PCB, Check on 24V line fuse, Replace the laser scanner unit copyir.com
E110-0001 Error in polygon motorSpeed lock of the FG speed control fails to be executed 5 sec after the polygon motor starts to operate (Does not reach the specified speed) copyir.com Check on connection between the laser scanner unit and the DC controller PCB, Check on 24V line fuse, Replace the laser scanner unit copyir.com
E193-0001 Error in IMG1 (error in add-on)
Error in initialization of image ASIC of DC controller PCB (IMG) Replace DC controller PCB
E202-0001 CIS unit HP detection error
The HP sensor fails to be ON after the CIS unit moves backward for a specific distance or more copyir.com Disconnect and then connect the connector, Replace the scanner HP sensor, Replace the scanner motor, Replace the reader controller PCB
E202-0002 CIS unit HP detection error
The HP sensor fails to be OFF after the CIS unit moves forward for a specific distance or more copyir.com Disconnect and then connect the connector, Replace the scanner HP sensor, Replace the scanner motor, Replace the reader controller PCB
E225-0001 CIS light quantity error
Normal light-up of the lamp fails to be confirmed at the time of power-on and shading correction when a job starts copyir.com Disconnect and then connect the connector, Replace the document lamp (xenon tube), Replace the CIS, Replace the inverter PCB, Replace the reader controller PCB copyir.com
E227-0001 Power supply error in the reader unit
24V port is off at power-on copyir.com Disconnect and connect the power supply connector, Replace the power supply
E227-0002 Power supply error in the reader unit
24V port is off when a job starts copyir.com Disconnect and connect the power supply connector, Replace the power supply
E227-0003 Power supply error in the reader unit
24V port is off when a job terminates copyir.com Disconnect and connect the power supply connector, Replace the power supply
E227-0004 Power supply error in the reader unit
24V port is off during a drive under load copyir.com Disconnect and connect the power supply connector, Replace the power supply
E240-0000 Error in communication of controller
Error in communication data copyir.com Disconnect and connect the main controller PCB (sub SJ-A/ PDRM-EF-A), or replace it copyir.com Replace the main controller PCB (main) copyir.com
E240-0001 Error in communication of controller
There is no response when 3 sec passed since the main controller had sent the pickup request to DC controller during printing copyir.com Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E240-0002 Error in communication of controller
There is no response when 4 sec passed since the main controller had sent the request for image output to DC controller during printing copyir.com Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E240-0003 Error in communication of controller
The engine is activated when jam occurs copyir.com Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E240-0004 Error in communication of controller
When 90 seconds pass as the pre-rotation end waiting Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E240-0005 Error in communication of controller
When 90 seconds pass as the Dhalf beginning waiting Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E243-0000 Control panel unit error
Communication between the main controller and the control panel unit is abnormal copyir.com Check on connection between the main controller PCB and the control panel unit
E244-0000 Error in connection of the flexible cable on the DC controller PCB
Error in connection of the flexible cable on the DC controller PCB (right side (1 pc copyir.com)) Check the connection of the flexible cable, replace the DC controller PCB
E244-0001 Error in connection of the flexible cable on the DC controller PCB
Error in connection of the flexible cable on the DC controller PCB (left side (3 pc copyir.com)) Check the connection of the flexible cable, replace the DC controller PCB
E248-0000 Backup memory error
Check error of the SRAM PCB (at start up) Check on connection of the SRAM PCB, Replace the SRAM PCB
E248-0001 Backup memory error
Reader controller EEPROM error at power-on Replace the reader controller PCB
E248-0002 Backup memory error
Reader controller EEPROM writing error Replace the reader controller PCB
E248-0003 Backup memory error
Reader controller EEPROM reading error after check error writing Replace the reader controller PCB
E351-0000 Main controller PCB error
Communication error of the main controller PCB occurs at start-up copyir.com Disconnect and connect the main controller PCB (sub SJ-A/ PDRM-EF-A/R-A), or replace it copyir.com Replace the main controller PCB (main) copyir.com
E400-0001 Feeder communication error
Checksum error – Check the connection of the cable – Check on connection between the ADF controller PCB and the main controller PCB (sub), Replace the ADF controller PCB, Replace the main controller PCB (sub
E400-0002 Feeder communication error
Reception status error – Check the connection of the cable – Check on connection between the ADF controller PCB and the main controller PCB (sub), Replace the ADF controller PCB, Replace the main controller PCB (sub
E400-0003 Feeder communication error
Reception interrupt error – Check the connection of the cable – Check on connection between the ADF controller PCB and the main controller PCB (sub), Replace the ADF controller PCB, Replace the main controller PCB (sub
E413-0001 Pressure motor trouble
Pressure HP sensor OPEN Replace the pressure motor copyir.com
E413-0002 Pressure motor trouble
Pressure HP sensor CLOSE Replace the pressure motor copyir.com
E490-0001 Error in different feeder model
Feeder for other model is detected copyir.com Connect an appropriate feeder
E503-0002 Finisher internal communication error
Communication error between the finisher and the saddle unit Check on connection between the saddle stitcher controller PCB and the finisher controller PCB, Replace the finisher controller PCB, Replace the saddle stitcher controller PCB
E503-0003 Finisher internal communication error
Communication error between the finisher and the puncher unit Check on connection between the saddle stitcher controller PCB and the finisher controller PCB, Replace the finisher controller PCB, Replace the saddle stitcher controller PCB
E505-0001 Finisher backup memory error
Data stored in the backup memory is abnormal copyir.com Check on connection between the DC controller PCB and the finisher controller PCB, Replace the finisher controller PCB, Replace the DC controller PCB
E505-0002 Finisher backup memory error
Abnormality of puncher unit EEPROM data Check on connection between the puncher controller PCB and the finisher controller PCB, Replace the finisher controller PCB, Replace the puncher controller PCB
E505-0003 Finisher backup memory error
Finisher controller EEPROM writing error Replace the finisher controller PCB
E505-0004 Finisher backup memory error
Finisher controller EEPROM writing timeout error Replace the finisher controller PCB
E508-0001 Error in different model
At start-up, when the pickup/delivery option for different model is detected copyir.com Replace to the supported pickup option (side paper deck), delivery option (finisher) for this model copyir.com
E514-8001 Stack delivery error / End assist motor error Finisher-Z1
The HP sensor fails to be ON within 1500ms after the return belt starts to move to its HP copyir.com Check on a drive of the stack retaining roller, Replace the return belt U-turn HP sensor (SR5) , Replace the stack delivery motor (M2)
E514-8001 Stack delivery error / End assist motor error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be OFF after the end assist motor rotates for a specific period of time copyir.com Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)
E514-8002 Stack delivery error / End assist motor error Finisher-Z1
The HP sensor fails to be OFF within 1500ms after the return belt starts to move to the belt contact position copyir.com Check on a drive of the stack retaining roller, Replace the return belt U-turn HP sensor (SR5) , Replace the stack delivery motor (M2)
E514-8002 Stack delivery error / End assist motor error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be ON after the end assist motor rotates for a specific period of time copyir.com Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)
E519-8001 Gear change motor error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be OFF after the end assist motor rotates for a specific period of time copyir.com Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)
E519-8002 Gear change motor error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be ON after the end assist motor rotates for a specific period of time copyir.com Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)
E530-8001 Rear alignment error Finisher-Z1
The HP sensor fails to be ON within 2000ms after the rear adjuster plate starts to move to its HP copyir.com Replace the rear adjuster plate HP sensor (SR4) , Replace the rear adjuster plate motor (M4)
E530-8001 Front alignment error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be OFF after the front jog motor rotates for a specific period of time copyir.com Replace the front adjuster plate HP sensor (PI36) , Replace the front adjuster plate motor (M33)
E530-8002 Rear alignment error Finisher-Z1
The HP sensor fails to be OFF within 1000ms after the rear adjuster plate starts to move from its HP copyir.com Replace the rear adjuster plate HP sensor (SR4) , Replace the rear adjuster plate motor (M4)
E537-8002 Front alignment error Finisher-Z1
The HP sensor fails to be OFF within 1000ms after the front adjuster plate starts to move from its HP copyir.com Replace the front adjuster plate HP sensor (SR3) , Replace the front adjuster plate motor (M3) , Replace the adjuster plate drive belt
E537-8002 Rear alignment error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be ON after the swing motor rotates for a specific period of time copyir.com Replace the rear adjuster plate HP sensor (PI37) , Replace the rear adjuster plate motor (M34)
E540-8001 Upper tray up/down error Finisher-Y1, Saddle Finisher-Y2
The upper tray up/down motor clock is abnormal copyir.com Replace the shift motor (M37) of the tray 1, Replace the shift area sensor PCB of the tray 1
E540-8002 Stack tray up/down error Finisher-Z1
Paper surface detection fails to end within 1000ms copyir.com Replace the stack tray top paper sensor (SR9) , Replace the stack tray bottom paper sensor (SR10) , Replace the stack tray upper limit sensor (SR13) , Replace the stack tray lower limit sensor (SR12) , Replace the stack tray shift motor (M7)
E540-8002 Upper tray up/down error Finisher-Y1, Saddle Finisher-Y2
Area is abnormal copyir.com Replace the shift motor (M37) of the tray 1, Replace the shift area sensor PCB of the tray 1
E540-8003 Stack tray up/down error Finisher-Z1
Encoder lock within 200ms fails to reach 10pulse during paper surface detection copyir.com Replace the stack tray top paper sensor (SR9) , Replace the stack tray bottom paper sensor (SR10) , Replace the stack tray upper limit sensor (SR13) , Replace the stack tray lower limit sensor (SR12) , Replace the stack tray shift motor (M7)
E540-8003 Upper tray up/down error Finisher-Y1, Saddle Finisher-Y2
The safety switch is activated copyir.com Replace the shift motor (M37) of the tray 1, Replace the shift area sensor PCB of the tray 1
E540-8004 Stack tray up/down error Finisher-Z1
Outputs of the top paper sensor, bottom paper sensor, tray upper limit sensor, and tray lower limit sensor have abnormality during paper surface detection copyir.com Replace the stack tray top paper sensor (SR9) , Replace the stack tray bottom paper sensor (SR10) , Replace the stack tray upper limit sensor (SR13) , Replace the stack tray lower limit sensor (SR12) , Replace the stack tray shift motor (M7)
E542-8001 Lower tray up/down error Finisher-Z1
The lower tray up/down motor clock is abnormal copyir.com Replace the shift motor (M38) of the tray 2, Replace the shift area sensor PCB of the tray 2
E542-8002 Lower tray up/down error Finisher-Z1
Area is abnormal copyir.com Replace the shift motor (M38) of the tray 2, Replace the shift area sensor PCB of the tray 2
E542-8003 Lower tray up/down error Finisher-Z1
The safety switch is activated copyir.com Replace the shift motor (M38) of the tray 2, Replace the shift area sensor PCB of the tray 2
E577-8001 Paddle error Finisher-Z1
The HP sensor fails to be ON within 1500ms after the paper retaining paddle starts to move to its HP copyir.com Replace the paddle HP sensor (SR8) , Replace the paddle motor (M6)
E577-8002 Paddle error Finisher-Z1
The HP sensor fails to be OFF within 1000ms after the paper retaining paddle starts to move from its HP copyir.com Replace the paddle HP sensor (SR8) , Replace the paddle motor (M6)
E584-8001 Shutter unit error Finisher-Y1, Saddle Finisher-Y2
The shutter open sensor fails to be OFF (The shutter cannot be closed) copyir.com Replace the stack ejection motor (M32) , Replace the shutter open/close clutch (CL31), Replace the shutter HP sensor (PI45)
E584-8002 Shutter unit error Finisher-Y1, Saddle Finisher-Y2
The shutter open sensor fails to be ON (The shutter cannot be opened) copyir.com Replace the stack ejection motor (M32) , Replace the shutter open/close clutch (CL31), Replace the shutter HP sensor (PI45)
E590-8001 Puncher motor error Puncher Unit
The puncher HP sensor fails to be detected after the puncher motor is driven for 200ms copyir.com Replace the puncher HP sensor, Replace the puncher motor
E590-8002 Puncher motor error Puncher Unit
The puncher fails to detect the puncher HP sensor after the puncher motor stops during initial operation copyir.com Replace the puncher HP sensor, Replace the puncher motor
E591-8001 Puncher dust sensor error
Light receiving voltage at the time of light emission is abnormal copyir.com Replace the puncher dust sensor
E591-8002 Puncher dust sensor error
Light receiving voltage at the time of non-light-emission is abnormal copyir.com Replace the puncher dust sensor
E592-8001 Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal copyir.com Replace the end sensor
E592-8002 Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal copyir.com Replace the end sensor
E592-8003 Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal copyir.com Replace the side registration sensor 1
E592-8004 Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal copyir.com Replace the side registration sensor 1
E592-8005 Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal copyir.com Replace the side registration sensor 2
E592-8006 Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal copyir.com Replace the side registration sensor 2
E592-8007 Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal copyir.com Replace the side registration sensor 3
E592-8008 Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal copyir.com Replace the side registration sensor 3
E592-8009 Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal copyir.com Replace the side registration sensor 4
E592-800A Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal copyir.com Replace the side registration sensor 4
E593-8001 Puncher shift motor error
The HP sensor fails to be OFF copyir.com Replace the HP sensor, Replace the puncher shift motor
E593-8002 Puncher shift motor error
The HP sensor fails to be ON copyir.com Replace the HP sensor, Replace the puncher shift motor
E5F0-8001 Saddle paper positioning error
The paper positioning plate HP sensor fails to be ON after the paper positioning plate motor is driven for 1 copyir.com33 sec copyir.com Replace the paper positioning plate motor (M4S), Replace the paper positioning plate HP sensor (PI7S)
E5F0-8002 Saddle paper positioning error
The paper positioning plate HP sensor fails to be OFF after the paper positioning plate motor is driven for 1 sec copyir.com Replace the paper positioning plate motor (M4S), Replace the paper positioning plate HP sensor (PI7S)
E5F1-8001 Saddle paper folder error
The number of detection pulses for the paper folder motor clock sensor is below the specific level copyir.com Replace the paper folder motor (M2S), Replace the paper folder motor clock sensor (PI4S)
E5F1-8002 Saddle paper folder error
The paper folder HP sensor fails to change after the paper folder motor is driven for 3 sec copyir.com Replace the paper folder motor (M2S), Replace the paper folder motor clock sensor (PI4S)
E5F2-8001 Saddle guide error
The guide HP sensor fails to be ON after the guide motor is driven for 0 copyir.com455 sec copyir.com Replace the guide motor (M3S), Replace the guide HP sensor (PI13S)
E5F2-8002 Saddle guide error
The HP sensor fails to be OFF after the guide motor is driven for 1 sec copyir.com Replace the guide motor (M3S), Replace the guide HP sensor (PI13S)
E5F3-8001 Saddle alignment error
The adjuster plate HP sensor fails to be ON after the jog motor is driven for 0 copyir.com5 sec copyir.com (for 1 copyir.com67 sec copyir.com during initial operation) Replace the jog motor (M5S), Replace the adjuster plate HP sensor (PI5S)
E5F3-8002 Saddle alignment error
The adjuster plate HP sensor fails to be OFF after the jog motor is driven for 1 sec copyir.com Replace the jog motor (M5S), Replace the adjuster plate HP sensor (PI5S)
E5F4-8001 Saddle rear side staple error
The stitching HP sensor fails to be ON after the stitcher motor (rear) rotates in the adverse direction for 0 copyir.com5 sec copyir.com or more copyir.com Replace the stitcher motor (rear, M6S), Replace the stitching HP sensor (rear, MS5S)
E5F4-8002 Saddle rear side staple error
The stitching HP sensor fails to be OFF after the stitcher motor (rear) rotates for 0 copyir.com5 sec copyir.com or more copyir.com Replace the stitcher motor (rear, M6S), Replace the stitching HP sensor (rear, MS5S)
E5F5-8001 Saddle front side staple error
The stitching HP sensor fails to be ON after the stitcher motor (front) rotates in the adverse direction for 0 copyir.com5 sec copyir.com or more copyir.com Replace the stitcher motor (front, M7S), Replace the stitching HP sensor (front, MS7S)
E5F5-8002 Saddle front side staple error
The stitching HP sensor fails to be OFF after the stitcher motor (front) rotates for 0 copyir.com5 sec copyir.com or more copyir.com Replace the stitcher motor (front, M7S), Replace the stitching HP sensor (front, MS7S)
E5F6-8001 Saddle paper push-on error
The paper pressure plate HP sensor fails to be ON after the paper pressure plate motor is driven for 0 copyir.com3 sec copyir.com or more copyir.com Replace the paper pressure plate motor (M8S), Replace the paper pressure plate HP sensor (PI14S)
E5F6-8002 Saddle paper push-on error
The paper pressure plate HP sensor fails to be OFF after the paper pressure plate motor is driven for 80ms or more copyir.com Replace the paper pressure plate motor (M8S), Replace the paper pressure plate HP sensor (PI14S)
E5F6-8003 Saddle paper push-on error
The number of detection pulses for the paper pressure plate motor clock sensor is below the specific level copyir.com Replace the paper pressure plate motor (M8S), Replace the paper pressure plate motor clock sensor (PI1S)
E5F6-8004 Saddle paper push-on error
The paper pressure plate leading edge sensor fails to be OFF after the paper pressure plate motor is driven for 80ms or more copyir.com Replace the paper pressure plate motor (M8S), Replace the paper pressure plate leading edge sensor (PI15S)
E5F6-8005 Saddle paper push-on error
The paper pressure plate leading edge sensor fails to be ON after the paper pressure plate motor is driven for 0 copyir.com3 sec copyir.com or more copyir.com Replace the paper pressure plate motor (M8S), Replace the paper pressure plate leading edge sensor (PI15S)
E5F8-8001 Saddle connector error
Disconnection of the guide HP sensor connector is detected copyir.com Disconnect and then connect the guide HP sensor (PI13S) connector
E5F8-8002 Saddle connector error
Disconnection of the paper pressure plate HP sensor connector is detected copyir.com Disconnect and then connect the paper pressure plate HP sensor (PI14S) connector
E5F8-8003 Saddle connector error
Disconnection of the paper pressure plate leading edge sensor connector is detected copyir.com Disconnect and then connect the paper pressure plate leading edge sensor (PI15S) connector
E5F9-8001 Saddle switch error
Open of the inlet cover is detected for 1 sec copyir.com or more after the host machine starts initial rotation/printing while the following sensors detect their covers closed copyir.com – Inlet cover sensor (PI9S) – Front cover open/close sensor (PI2S) – Delivery cover sensor (PI3S) Or, the front cover switch (MS2S) or the delivery cover switch (MS3S) is open copyir.com Replace the inlet cover switch (MS1S), Replace the front cover switch (MS2S), Replace the delivery cover switch (MS3S)
E5F9-8002 Saddle switch error
Open of the front cover switch is detected for 1 sec copyir.com or more after the host machine starts initial rotation/printing while the following sensors detect their covers closed copyir.com – Inlet cover sensor (PI9S) – Front cover open/close sensor (PI2S) – Delivery cover sensor (PI3S) Replace the front cover switch (MS2S), Replace the delivery cover switch (MS3S)
E5F9-8003 Saddle switch error
Open of the delivery cover switch is detected for 1 sec copyir.com or more after the host machine starts initial rotation/printing while the following sensors detect their covers closed copyir.com – Inlet cover sensor (PI9S) – Front cover open/close sensor (PI2S) – Delivery cover sensor (PI3S) – Delivery cover switch (MS3S) Replace the inlet cover switch (MS1S), Replace the front cover switch (MS2S), Replace the delivery cover switch (MS3S)
E601-0000 Abnormality of image memory
Communication error of the image memory (SDRAM) Replace the SDRAM
E602 Hard disk error
E604-0000 The image memory (SDRAM) is faulty/insufficient
Memory capacity required for a model fails to be recognized copyir.com Add on the SDRAM
E604-0001 The image memory (SDRAM) is faulty/insufficient
Memory for MEAP application is insufficient copyir.com Add on the SDRAM
E604-0002 The image memory (SDRAM) is faulty/insufficient
The image memory of larger than 1 copyir.com5GB is installed (at activation) Make the memory 1 copyir.com5GB or less copyir.com
E604-0512 The image memory (SDRAM) is faulty/insufficient
Memory is faulty/insufficient (512MB is required) Add on the SDRAM
E604-0768 The image memory (SDRAM) is faulty/insufficient
Memory is faulty/insufficient (768MB is required) Add on the SDRAM
E604-1024 The image memory (SDRAM) is faulty/insufficient
Memory is faulty/insufficient (1024MB is required) Add on the SDRAM
E604-1536 The image memory (SDRAM) is faulty/insufficient
Memory is faulty/insufficient (1536MB is required) Add on the SDRAM
E609-0008 Abnormal low temperature of the hard disk
At start-up, temperature of the HDD fails to reach the specific level within a specific period of time copyir.com Replace the HDD
E609-0009 Abnormal low temperature of the hard disk
During recovery from sleep mode, temperature of the HDD is below the specific level within the specific period of time copyir.com Replace the HDD
E610 Failure in the hard disk cryptographic key
E611-0000 Error in repeat of reboot due to fault of SRAM, etc copyir.com
SRAM information is broken, job information stored in SRAM cannot be read and reboot is repeated at recovery from power-off Clear SRAM to delete the shutdown assurance job copyir.com
E674 FAX board communication error Check on connection between the FAX board and the main controller PCB, Replace the FAX board, Replace the main controller PCB
E677 Abnormality of the external controller Check on connection of the cable, Re-install the external controller system copyir.com Connect an appropriate controller, Re-install the external controller system copyir.com Check on connection of the cable, Re-install the external controller system
E710-0000 IPC initialization error
Error in initialization of IPC chip Check the connection of cable, Replace the DC controller PCB
E710-0001 IPC initialization error
The status fails to be ready within 3 sec after the IPC chip starts up copyir.com Check on connection of the cable
E711-0001 IPC communication error
Error is set to the error register of the IPC chip 4 times or more within 1 copyir.com5 sec Check on connection of the cable, Replace the ADF controller PCB, Replace the reader controller PCB
E713-0000 Communication error between the finisher and the printer
Communication between the finisher and the copier stops copyir.com Check on connection of the cable, Replace the finisher controller PCB, Replace the DC controller PCB
E716-0000 Error in communication to cassette pedestal, 2 / 3 delivery unit
Error in data communication with cassette pedestal Check cable connection, replace pedestal PCB, replace DC controller PCB
E716-0001 Error in communication to cassette pedestal, 2 / 3 delivery unit
Error in data communication with 2 / 3 delivery unit Check cable connection, replace 2 / 3 delivery unit PCB, replace DC controller PCB
E717-0001 Communication error with the NE controller
The NE controller connected before the power is turned off fails to be recognized at power-on copyir.com Check on connection of the cable To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR
E717-0002 Communication error with the NE controller
A break in the IPC, IPC communication fails to recover Check on connection of the cable To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR
E719 Communication error with the coin vender/card reader Check on connection of the cable To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR
E730 PDL error Reset PDL, Turn OFF and back ON the main power
E731 UFR PCB error Check on connection of the UFR PCB , Replace the UFR PCB, Replace the main controller PCB
E732-0001 Reader communication error
DDI-S communication error Check on connection between the reader controller PCB and the main controller PCB, Check on the reader power supply
E732-8888 Reader communication error
When the different scanner model is detected copyir.com Check the scanner model and the scan type at: COPIER > OPTION > BODY > SCAN TYPE, then make the scan type setting as below copyir.com 0 for CIS model reader 1 for CCD model reader
E732-9999 Reader communication error
When the scanner is initially detected on a printer model (not error) copyir.com Main power OFF/ON
E733-0000 Printer communication error
The printer fails to be detected at start-up copyir.com Check on connection between the DC controller PCB and the main controller PCB, Check on the printer power supply
E733-0001 Printer communication error
Abnormality of the Ethernet board Check on connection between the DC controller PCB and the main controller PCB, Check on the printer power supply
E740 Abnormality of the Ethernet board Replace the Ethernet board , Replace the main controller PCB (sub LAN-bar)
E743-0000 DDI communication error (Reader side detection)
The reader controller PCB detects communication error between the main controller PCB and the reader controller PCB copyir.com Disconnect and then connect the reader communication cable connector, Replace the reader controller PCB, Replace the main controller PCB
E744 Language file/BootROM error Upgrade the version of the Language file
E745 Token ring board error Check on connection of the token ring board, Replace the token ring board
E746 Option board error Replace with an appropriate UFR PCB copyir.com Replace with an appropriate main controller PCB (sub)
E747 Main controller PCB error (Image processing ASIC or memory control/communication control ASIC) Turn the main power off and turn it back on copyir.com Disconnect and connect the main controller PCB Replace the main controller PCB (Main) copyir.com
E748 Main controller PCB error (Image processing ASIC or memory control/communication control ASIC) Disconnect and then connect the main controller PCB (Sub SJA/ PDRM-EF-A/RO-A), Clean the terminal, Replace the main controller PCB (Sub SJ-A/PDRM-EF-A/RO-A), Disconnect and then connect the open interface PCB, Clean the terminal, Replace the open interface PCB, Replace the main controller PCB (main)
E749 Restart in accordance with a change of the product configuration Turn OFF and back ON the main power to recover copyir.com Recovered by turning the main power OFF / ON
E804-0000 Controller fan error
Stop of power supply cooling fan was detected Check the connection of power supply cooling fan, replace it
E804-0001 Controller fan error
Stop of power supply cooling fan 2 was detected Check the connection of power supply cooling fan 2, replace it
E804-0004 Controller fan error
Stoppage of the controller fan is detected for 16 sec continuously copyir.com Check on connection of the controller fan, Replace the controller fan
E805-0001 Fan error
Lock fails to be detected for 5sec continuously while the exhaust fan (front) is driven copyir.com Disconnection of the fan connector copyir.com Lock signal fails to be sent due to a fan failure copyir.com Check on connection of the exhaust fan (front), Replace the exhaust fan (front)
E805-0002 Fan error
Lock fails to be detected for 5sec continuously while the exhaust fan (rear) is driven copyir.com Disconnection of the fan connector copyir.com Lock signal fails to be sent due to a fan failure copyir.com Check on connection of the exhaust fan (rear), Replace the exhaust fan (rear)
E806-0001 Error in fan of main body
Error in delivery adhesive fan was detected Check the connection of delivery adhesive fan, replace it
E806-0002 Error in fan of main body
The drop of connector of delivery adhesive fan / the disconnection was detected Check the connection of delivery adhesive fan, replace it
E806-0003 Error in fan of main body
Error in secondary transfer exhaust fan was detected Check the connection of secondary transfer exhaust fan, replace it
E807-0001 Error in fan of process cartridge
Error in fan (front) of process cartridge was detected Check the connection of fan (front) of process cartridge, replace it
E807-0002 Error in fan of process cartridge
Error in fan (rear) of process cartridge was detected Check the connection of fan (rear) of process cartridge, replace it
E808-0000 Error in low-voltage power supply PCB (error in zero cross)
Error in low-voltage power supply PCB Replace low-voltage power supply PCB, replace DC controller PCB
E811-0000 Error in detection of new drum unit
Error in blowout of fuse for detection of new drum unit (process cartridge) Check the connection of drum unit, replace it Replace DC driver PCB
E811-0001 Error in detection of new drum unit
Error in blowout of fuse for detection of new drum unit (process cartridge) Check the connection of drum unit, replace it Replace DC driver PCB
E840-0000 Fan shutter error
Fan shutter open/close operation Error Abnormal rotation of the fan shutter motor Defect of the fan shutter position sensor Defect of the fan shutter home position error Defect of the DC controller PCB – Replace the fan shutter motor – Replace the fan shutter position sensor – Replace the fan shutter home position sensor – Replace the DC controller PCB
E990-0000 Error in the waste toner shutter
When the output of the waste toner shutter opening and shutting detection sensor doesn’t become “H” when it WMUPR period after the sleep returns after eight hours or more pass, the door opening and shutting is detected or main power switch turns on copyir.com – Check that the drum unit is properly installed – Replace the waste toner shutter sensor
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.